SPL REPAIR TO JOINERY, FLOOR TILING, BATHROOM, KITCHEN IN CERTAIN MD ACCN (04 NOS) AT TIGRIS ROAD UNDER GE (EAST) DELHI CANTT-10

Amount

Dismantling of Brickwork of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stone work and precast concrete articles

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Demolition of Reinforced cement Concrete in any description and any position n exc 15 cm thickness (below or above ground level)

Demolition cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes including all fittings and accessories, 100/75 mm bore and in any position all as specified.

Dismantling water tanks exc 500 Ltrs but not exc 1000 ltr capacity and removing from site.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each complete all as specified

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each complete.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm and refixing or resecuring in same opening complete.

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor Includes cost of glass and includes all other connected accessories. Net Opening will be measured for payment

All same as per item No 12 here-in-before but area exc 1.00 Sqm but n exc 2.00 complete all as specified.

M&L Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks and similar work conforming to Fe 290 Gde-E-165 all as specified .

S&F for Stainless steel wire mesh 0.36 mm nominal dia and avg width of aparture 1.4mm and fixed with stainless steel wire staples.

S&F Fiber Glass Reinforced Plastic (FRP) Door Frames of cross section 90mm x 45mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame complete all as speified and directed. Note : Colour and pattern shall be approved by GE.

S&F 30 mm thick Glass Fibre Reinforced Plastic (FRP) paneled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames complete all as specified and directed. Note : Colour and pattern shall be approved by GE.

Pressed steel frames size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling hollow portion of frames with PCC 1:3:6 Type C-0 using 12.5mm graded crushed stone aggregate etc., complete all as specified and as directed.Frame

Pressed steel frames size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling hollow portion of frames with PCC 1:3:6 Type C-0 using 12.5mm graded crushed stone aggregate etc., complete all as specified and as directed.

S&F for 35 mm thickness flush shutters, solid core construction, with particle board core and plywood face panels both faces covered with laminate decorative face veneer with lipping incl edge to match frame complete all as specified and directed.

S&F Factory made 2nd class hard wood,35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces with lipping. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F SS butt hinges 100mm long medium weight cold rolled mild steel etc

S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt, all as specified .

S&F aluminium anodised handle cast type of extruded section 150 mm long fixed with screws.

S&F aluminium anodised sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete.

S&F MS 250mm long ordinary rat tail rod pattern spring incl roller and plate complete all as specified

Rubber door seal 32mm wide with Aluminium strip of size 19mm wide fixed with machine steel screw with washer complete

Taking down Kitchen Cabinet/wardrob/shelf/cupboard etc similar article of any description and any position and removing from site including all fittings and frame work, complete all as specified and as directed.

S&F and fabrication of wardrobe/ cup board made out of 18-19 mm thick PVC board of density 600 kg/cum laminated sheet on both sides, colour as approved by GE, complete all as specified and directed.

PVC sheet white 15 mm thick fixed with approved adhesive and stainless steel machine screw (Star) in narrow widths of n-exc 10 cm width, complete all as specified and as directed.

S&F and fabrication of modular kitchen factory made out of 18-19 mm thick BWR PLY/HDHMR with laminations on both sides for base cabinets & upper cabinets, stainless steel basket consisting with the following specification :- (a) Multipurpose basket of size 21”x20”x4” (02 nos) with 5.3 mm thick SS wire. (b) Multipurpose basket of size 21”x20”x8” (01 No) with 5.3 mm thick SS wire. (c) Fix box cuttlery basket of size 21”x20”x4” (01 No) with 5.3 mm thick SS wire (d) Cup & saucer basket of size 21”x20”x4” (01 No) with 5.3 mm thick SS wire. (e) Plate basket of size 21”x20”x6” (01 No) with 5.3 mm thick SS wire. (f) Multipurpose basket of size 17”x20”x4” (01 No) with 5.3 mm thick SS WIRE. (g) Grain trolley with mechanism basket of size 17”x20”x13” (01 no) with 5.3 mm thick SS wire. (h) Detergent holder SS minimum wt of wire basket 0.75 kg (01 No) (j) Bin Holder SS minimum wt of wire basket 0.50 KG (01 No) (k) Plate Basket of size 21”X20”X6” (01 No) WITH 5.3 mm thick SS wire. (l) Thalli Basket of size 21”x20”x8” (01 No) with 5.3 mm thick SS wire. (m) GTPT SS of size 24”x10”, minimum wt 1.80 kg (01No) (n) Stainless Steel hydraulic auto soft close hinge as reqd at site (o) Stainless Steel telescopic channel as reqd at site (p) Stainless Steel handles for cabinets as reqd at site (q) Make: Action Tesa or equivalent Stainless Steel double bowl sink 3’ long incl waste pipe, CP waste coupling.

S&F 75 mm dia oval shape brass handle fancy type polished bright finish complete all as specified and directed.

S&F 100mm dia oval shape brass handle fancy type polished bright finish complete all as specified and directed.

S&F continues (piano) hinges, mild steel, bright finish width of flap (when open) 30mm.

S&F Hasp 100mm and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete

Magnetic catches with steel body ‘H’ type, fixed to shutter complete all as specified and as directed.

S&F 65 mm size brass Cup board lock, 4 lever grade I of superior quality all as specified and directed.

S&F Floor door stopper of brass body and tongue, anodized, with hard drawn steel fixed in floor with over all length of cover plate 140 mm fixed in repairs complete.

S&F in repair 20mm dia Stainless steel curtain rod with of superior quality fixed complete all as specified

S&F SS steel End bulb and SS bracket suitable for 20 mm dia drapory rod plete all as specified.

S&F in repair for 12 mm thick frameless toughened glass Shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type with fixing arrangement and making necessary holes etc. for fixing required fittings, including taking down of existing work all complete as per direction of Engineer-incharge

M&L for 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors finished rough all as specified.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl 20 mm thick screed bed in Cement Mortar (1:4) complete all as specifed and dircted .

Molding (Sandwitch moulding) of granite slab edges as directed by Engr-in-charge including polishing etc complete

M&L for drilling and making hole in marble/granite slab of cooking plateform for cooking gas pipe etc n. exc 25 mm dia all as directed by Engineer-in-Charge.

M&L for Vetrified ceramic tiles ultra charged ( dark shade) 10mm thick (square/rectangular) area of each tile exc 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:4) complete all as specified

All same as per srl item No 47 here-in-before but with 10mm thick rendering in CM 1:4 as in backing coat for dado/skirting complete all as specified.

M&L for Non skid ceramic coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:6) complete all as specified

M&L for 1st/Premium quality glazed ceramic digital coloured tiles with highlighter concetp in matching pattern of size 1200X 600X 7 to 8 mm thick as in vertical surfaces such as skirtings, dados etc set & jointed in neat cement slurry & pointed with white or coloured cement to match the shade of tiles over and incl 15 mm thick rendering coat in CM (1:4) incl dismantling of existing tiles complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) as in shelves supported on walls using cement concrete type B-1 1:2:4 (20mm graded aggregate) complete.

Formwork to soffits of suspended slabs such as in shelves not exceeding 200mm thick rough finished flat surfaces of concrete complete all as spd and directed

Form work to edges of concrete flat exc 5 cm but n-exc 10cm wide for rough finished flat surfaces of concrete complete.

M&L TMT bar 10mm dia and over dia cut to length, bent to shape required incl cranking bending and binding with and including mild steel wire(annealed) not less then 0.9mm dia

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, helves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth but n exc. 20mm girth.

Supplying and laying 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings including short lengths, fixed to wall and ceiling or laid in floor complete all as specified and directed.

Supplying and laying 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings including short lengths, fixed to wall and ceiling or laid in floor complete all as specified and directed.

S&F in repair for 15 mm dia Bib Cock with Wall Flange as per manufacture’s manual complete all as specified and directed Make : JAQUAR OPP-15037PM or equivalent in Hindware.

S&F in repair for 15mm brass CP Angle stop cock with wall flange complete. Make : JAQUAR AQT- CHR 3057 or equivalent in Hindware.

S&F in repair for 15mm brass CP Angle stop cock (Concealed type) with wall flange complete. Make : JAQUAR ALD- CHR 083 or equivalent in Hindware.

S&F in repair for 15 mm dia 2 Way Bib Cock with Wall Flange as per manufacture’s manual complete all as specified and directed Make : JAQUAR OPP-15041PM or equivalent in Hindware.

S&F in repair Wall mixture with CP Telephonic shower pipe fixed over wall surface as per manufacturets mannual and Square Over Head shower (200mmx200mm) including easy flex shower tube with hand shower 68mm dia round shape single flow (ABS body chrome plated with rubit cleaning system etc complete all as specifed and directed Make : JAQUAR SHFLR 5281N or Hindware.

S&F in repair sink mixture with regular swinging spout (wall mounted modle ) with connecting legs & wall flanges) for 15 mm bore complete all as specifed and directed Make : JAQUAR FLR 5309N or Hindware

S&F in repair Center hole basin mixer with wall flage 15mm dia chromium plated brass with costed swinging spout including plugging and fixed as position complete Make : JAQUAR FLR 5167NB or equivalent in Hindware.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. Make : JAQUAR CAN-CHR-1173 N or Hindware.

S&F in repair for corner Acrylic self up of size 225mmx225mm radius fixed in position complete.Make : JAQUAR or Hindware.

S&F in repair for Toilet Paper Holder fixed in position complete. Make : JAQUAR ACN 1153N or Hindware.

S&F in repair for towel rail 300mm long fixed in position complete. Make : JAQUAR CAN CHR 1101S or Hindware.

S&F in repair for Towel ring fixed in positon complete.Make : JAQUAR 1121N or Hindware.

S&F in repair for Brass soap dish (Chrome) with wall flange fixed in positon complete.Make : JAQUAR AEC 1131or Hindware.

S&F in repair Brass Chromium plated shower rose 150x150mm size with or without swivel joints, any size incl SS shower arms fixing to steel pipe or union complete.

S&F CP Health faucet with 1.00Mtr long CP flexible pipe as per approved sample complete all as specified and as directed by Engineer-in-Charge. Make : JAQUAR Ald CHR 563 or equivalent in Hindware.

5.50 mm thick looking mirror with decorative edging on border/moulded edges of requied size area exc 1 Sqm but not exc 2.00 sqm each with suitable fixing arrangements in wall complete all as specified and directed.

S&F in repair PVC Cabinet mirror of size 450x300mm fixed with screw and PVC gutties on wall complete all as specified and directed Make : Prayag Cat part/Item Code 557 Equivalent in Shakti as approved.

S&F Stainless steel peg set (set of 06 hook) as per sample kept in GE office fixed in position with screw and PVC gutty on wall in repairs, complete all as specified and as directed.

S&F vitreous chinaware white colour oval shape counter top wash hand basin (WHB) size 640mm x 425mmx155mm complete, 1st quality, fixed over granite stone slab with and including suitable waste pipe and waste fitting coupling 32 mm bore long screwed shank and fly nuts complete all as specified and directed (Make – Jaquar WHT - 25901 or Equivalent In Hindware).

S&F in repair Vitreous china squalting pan of Orrisa pattern long pan size 580mmx440mm white with 'P' or 'S' trap front or back inlet and foot rest any pattern including connection to trap and to flushing pipe etc complete including lime concrete bedding and making good to floor.

S&F Vitreous china floor mounted toilet one piece type (white) including connection in drain etc incl ,plastic water closet seat cover, CP Jet sprey and P or S trap, fixed in repairs, complete all as specified and as directed. Make : Hindware Cat Part No 192055 or equivalent in Cera/Hindware.

S&F in repair PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete including taking down by dismantling the existing unserviceable cistern of any description.(Make: - Parryware or equivalent in Hindustan Sanitary ware/Cera)

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm long complete.

PVC waste pipe 60 to 80 cm long sutible for sink/wash hand basin, fixed in repairs, complete all as specified and as directed.

S&F Rotational molded polyethylene water storage tanks (cylindrical vertical with threaded lead) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 litres all as specified .

S&F in repair ball brass valve high pressure with polythene float and fly nut complete screwed for Iron pipe 20mm bore

S&F in repair Gun metal gate valve with iron wheel head screed both ends for iron pipe and fixed 20mmm bore complete

M&L in repair PVC (SWR) multi floor trap with grating in cluding jointing with solvent cement 63/75mm dia of outlet.

S&F PVC (SWR) pipes, 110 mm bore double socketed in any length with rubber joints, as in walls/floor complete all as specified.

S&F PVC (SWR) pipes, 75 mm bore double socketed in any length with rubber joints, as in walls/floor complete all as specified.

S&F PVC(SWR) bends suitable for 100 mm bore complete all as specified

S&F PVC (SWR) junction single, (single T) equal or unequal of 100mm bore

S&F PVC(SWR) bends suitable for 75 mm bore complete all as specified

S&F PVC (SWR) junction double, (double T) equal or unequal of 75mm bore with access door

S&F PVC (SWR) vent cowl of 110mm bore

S&F for stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipecomplete all as specified and directed.

M&L brick work with sub class 'B' st or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete.

M&L for Brickwork with subclass `B' bricks, straight or curved on plan to any radius in half thick brick built in CM (1:4) complete.

M&L for 50 mm thick in Plain cement concrete type C2 (1:3:6)( using 40 mm graded aggregate ) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as directed at site.

Taking down cement plaster on brick wall including racking out joints hacking for key scrubing down with water etc

M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface of wall finished. (Note: Crushed stone sand will be used for plaser work)

M&L for 10mm thick cement plaster on brick or concrete surfaces, as in ceiling / facia / chajja etc. in cement mortar 1:3 finished even and fair complete all as specified . (Note: . Crushed stone sand will be used for plaser work).

M&L for 15 mm thick external rendering on brick work or cement concrete surfaces in cement mortar 1:4, finished even and fair incl mixing of water proofing compound complete all as specified. (Note: 1. Water Proofing compound shall be measured and paid for separately 2. Crushed stone sand will be used for plaser work ).

Supply only water proofing compound (Makes :Pidilite Industries / Impermo /Snowcem India Ltd / Sika )

M & L for preparation of old decorated external wall and ceiling surface by sand paper of required sizes filling in wall care putty in potholes existing or created ,again sand papering thus making surface smooth and two coat of weather proofing exterior acrylic emulsion paint complete all as specified and directed

M&L for preparation Internal wall and ceiling surface old by complete removal of existing treatment of walls for upto 4 storey buildings by mechanised sander of Berger Paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools as required and applying a layer of 1mm thick wall care putty, again sand papering thus making surface smooth and applying one coat of primer and applying two coats of premium qualiy exterior acrylic emulsion paint (weather coat) on surfaces complete all as specified and directed by Engr-in-charge. Note : (i) Final finishes to be applied with roller.

M&L for preparation Internal wall and ceiling surface old/new by complete removal of existing treatment of walls for upto 4 storey buildings by mechanised sander of Berger Paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools as required and applying a layer of 1mm thick wall care putty, again sand papering thus making surface smooth and applying one coat of primer and applying two coats of interior grade acrylic emulsion paint premium quality on surfaces complete all as specified and directed by Engr-in-charge. Note : Final finishes to be applied with roller.

S&F Suspended Gypsum board ceiling works in decorative steps including vertical/sloping members includes with GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) alongwith perimeter of nailing screw fixed in brick wall/RCC with the help of nylon seelves and screws at 610mm centre, then suspending GI intermediate channels of size 45mm (0.9mm thick with two flange of 15mm each) from the soffits at 1220mm centre with GI cleat and steel expansion fasteners, ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm centres, 12.5mm tapered edge gypsum board conforing to IS 2095 (1982) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centre,. Screws fixing is done mechanically either with screw driver or drilling machine with suitable attachment finally the board are to be jointed and finishing the tapered and square edges of the boards are to be joints compound, joint fiber tape including dismatling of old false ceiling any description. Note :- Details of fixing & material will be got approved by GE before commencement of work.

M&L Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified.

M&L Preparation of new wooden or wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

M&L for 75mm thick cement concrete 1:3:6, Type C-1 ( using 20mm graded stone aggregate) as in sub-bases, floors and pavings complete as specified and directed.

M&L Pre polished coloured bullnosed cement concrete tiles 300mm x 300mm x 25mm thick, set, jointed with coloured cement and pigment and pointed in neat cement slurry in floors, pavements etc over incl 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L PCC type B-1 1:2:4 using 20mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edgs. complete all as specified and directed.

M&L E-board 4mm thick self design type tiles ceiling on GI Powder coated channel /Tee/Grid of make (Armstrong or equivalent) including cutting holes to brick wall built in cement mortar & making good in cement mortar 1:3 or concrete 1:2:4 type B-0 as required frame work including taking down existing unserviceable ceilings board alongwith frame work of any type, new ceiling to be of following specification :- (a) Plugging to wall around the rooms & supplying & fixing GI Powder coated angle of size 25mm x 25mm x 1.0 mm (b)1.60mm dia GI wire suspenders with adjustable clamps including fixing to ceiling dash free fasterers (c)25mm x25mm x 1.5mm GI Powder coated tee as in main & cross members at 595mm c/c supported suspenders alongwith adjustable clamp to maintain level . (d) E-board 4mm thick self design type ceiling tiles of size 600mm x 595mm confirming to relevant IS in squares of GI Powder coated Tee with clips made to shape, complete all as specified and as directed.

M&L for cutting holes into of through brick walls exc half brick but n exc one brick built in cement mortar for inserting hold fast and making good dismentled porton in cement mortar 1:3 or cement concrete 1:2:4 type B1 all as specified and directed

M&L for Mild steel work as in Hollow section, angle Iron, flat Iron for fixed indepently connecting purlin, rafters, MS plate as reqd forming holes bolted and welded attchment and curved shaped by welding (thickness of metal n.exc 6mm) making jointless by filling including cutting etc complete all as specified.

S & F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws incl taking down existing CGI sheet complete all as specified.

M&L for prepration of surface on wall and ceiling for filling cracks with Smart care Textutred crack filler with following steps. 1) Open the Crack and widen it to form of V' shaped groove with help of Chisel. 2) Clean the area throughly so that it is free from dust and loose particles. 3) Apply a shelf priming coat (1:1) dilution with water ) of smart care textured crack filler over crack edges and allow to dry it for 1- 2 hrs. 4) Apply first coat of undiluted smart care Textured crack filler on the crack using spatula or putty Knife. 5) Press the paste firmly in the crack to ensure full contact with the surface .6) Spread Smart care Textured cracks Filler up to atleast 3 cm on either side of the crack for better adhesion. 7) Apply in consecutive prependiculkar layers to avoid leaving air pockets . 8) allow to dry for a minium 6 hrs. 9) apply the second undiluted coat in the in the same manner as required.

S&F in repair vanity box of HDHMR of size 580x450x680 mm with Mirror Cabinet of Size 500x700mm with table top basin complete all as specifies and directed Make- Amara in Parryware Main Cabinet C896146 Mirror Cabinet C896C46 or Equivalent in Kohler or Marc.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for taking credit and making good disturbed surfaces complete all as directed.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) including FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches/sockets/fan regulator etc , with and including Modular cover plates of suitable size and making good surface complete all as directed for the following :-

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

All as per srl item No. 120 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire on independent board

S&F Modular switch 6 Amp, 1 way, 1 module size complete all as specified and as directed.

S&F Modular Bell push 6A 1 module complete all as specified and as directed

S&F Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as specified and as directed.

S&F Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as specified and as directed

S&F Modular socket 6/16 Amp multipurpose , 2 module complete all as specified and as directed.

S&F Modular Fan regulator step type, 120 watts complete all as specified and as directed

S&F Call bell ding dong type, AC, 230V complete all as specified and as directed.

S&F Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps complete all as specified and as directed

S&F PVC batten holder including 9W LED bulb all as specified and directed.

S & F in replacement LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, 20 Watts, cool/warm white as per site requirement complete all as specified and directed..

S&F Recess/Surface mounting 2x2 square flat panel ultra slim scoop LED light 36 W warm/cool white with driver/transformer etc suitable for Grid ceiling/Gypsum board/POP ceiling incl making electric connection complete as as directed. Make: Syska/havels/philipsC&S/Polycab

S & F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, 10 Watts, cool/warm white as per site requirement complete all as specified and directed..

Supply and fixing wall light fitting comet type suitable for LED lamp with B 22 base complete all as specified and as directed.

S & F energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

Supply and fixing in replacement of street light fitting bracket, 1.0 mtr long made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Supply and fixing in replacement of LED bed side light, 5/6 Watts, wall mounted type and making all electric connections complete all as specified and directed.

Supply and fixing in replacement of Ventilating fan 250 mm sweep plastic body type including self cosing louver and making all electric connections and depositing u/s to MES store yard complete all as directed.

S&F In ceiling fan 1200 mm sweep with blades, down rod, and accessories with BLDC motor without remote and depositing the old u/s to MES store yard complete all as specified.

Supply and fixing Wall Mounted Fan 400 mm sweep plastic body type including making all electric connections and depositing the old u/s to MES store yard complete all as directed

Supply and fixing Water Heater (Geyser) 25 ltre capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners (4No.) for hanging and CP and PVC connection for inlet and outlet upto stop cock including taking down the old u/s geryser and depositing to MES store yard complete all as specifed and directed.

Supply and fixing Water Heater (Geyser) 3 ltre capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners (4No.) for hanging and CP and PVC connection for inlet and outlet upto stop cock complete all as specifed and directed.

Supply and fixing of exhaust fan upto 300 mm sweep metalic body type and making all electric connections complete all as directed and depositing the old U/s item to MES store yard.

M&L in replacement Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into and incl PVC concealed conduit 25 mm dia with all fittings and 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire complete all as specified and as directed.

M&L in replacement for Sub main wiring with 2 run of 6 .0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into and incl PVC concealed conduit 25 mm dia with all fittings and 6.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire complete all as specified and as directed

M&L in replacement for Sub main wiring with 2 run of 4 .0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into and incl PVC concealed conduit 25 mm dia with all fittings and 4.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire complete all as specified and as directed

S&F in replacement Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 08 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

S&F in replacement Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 04 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed

Supply and fixing in replacement of Modular AC Socket with 25 Amps SP mini MCB, 230 Volts, 50Hz. In 4 module sheet metal enclosure complete all as specified and as directed.

S&F MCB in replacement SP, C Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F in replacement Isolator SPN 40 Amp, complete all as specified and as directed

Supply and fixing in replacement of MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections and taking out the old unserviceable DB complete all as directed.

S&F MCCB in replacement 3P 125 Amp with breaking capacity 16 KA suitable for 415 volts AC supply, with over load and short circuit protection complete all as specified

Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed.

Supply and fixing of high pressure booster pump with 8 ltr capacity pressure tank, coupled with electric motor of capacity 0.50 HP, 230 volts, single phase, 50 Hz incl Pressure Guage, Pressure switch & connecting accessories of GI i.e bend, nipple, socket, tee of requisite size etc incl cutting of existing pipe complete all as directed.

S& F Static Energy Meter three phase electronic type with LCD display of capacity 10-60A including connection with seal and sealing wire including taking out the old u/s and depositing to MES store yard complete all as specified and as directed

Supply and fixing in replacement of LED post top lantern fitting powder coated aluminium die cast and spun aluminium with clear/opal diffuser 25 Watt incl LED driver with gallary suitable for mounting on 32/40 mm GI pipe including necessary electric connections complete all as directed.

Supply and fixing in replacement of LED ceiling light fitting 15 watt, in round shape, surface/recess type cool/warm white as per site requirement and making all electric connections complete all as directed.

Supply and fixing in replacement of LED ceiling light fitting 10 watt, in round shape, surface/recess type cool/warm white as per site requirement and making all electric connections complete all as directed.

Supply and fixing Flexible LED strip light tubular type, any colour , incl LED AC to DC adopter and making all electric connections complete all as directed.

Supply and fixing AC to DC adaptor for LED strip light tubular type complete all as specfied and as directed

Supply and fixing cable pvc insulated copper conductor unsheathed 1.5 sqmm for fitting in false ceiling for connection complete all as specified

Vipul Construction

Akhil Enterprises

aggarwal engineers contractors

M/s SAAR ENGINEERS