S/R to Craig Garden No.5 at Barnes Court Shimla. (SH-Covering of path from main roar to office building.)

Amount

Cutting in earth work in all heights/depths and in all kinds of soil such as kankar, moorum, shingle and decomposed or soft rock and hard rock including their intermediate classification and chiselling / wedging out rock where blasting is prohabited including saturated soil and filling in embankment etc., where necessary and disposal of all excavated un serviceable materials in all leads and lifts including through mechanical transporation, the disposal of unserviceable materials will be done in acquired width of the road or on approved dumping site.

Excavation in foundations, trenches etc. in all kinds of earth work including spade work, pick work, jumper work blasting work including where blasting is prohibited and chiselling/ wedging out of rock etc. upto all lifts stacking the excavated soil not more than 3meters clear from the edge of the excavation and then returning the stacked soil in 15cm layer when required into plinths, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth within all leads and lifts as directed by Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling in all heights in all floors and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like including carriage of materials in all leads and lifts.

Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 25 mm nominal size) and curing complete excluding cost of centring and shuttering including carriage of materials in all leads and lifts in foundations and plinth.

Steel work welded in built up sections including hollow section, trusses and framed work, including cutting hoisting fixing in position and applying a priming coat of red lead paint in beams joists, channels, angles, tee, flats including hollow sections with connection plate or angle cleats as in main and cross beam hips and jack rafter, purlins connected to common rafter and the like including carriage of materials within all leads and lifts.

Providing and fixing 0.60mm thick prepainted steel sheet Tata Durashine or equivelant in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5microns over 5microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of materials upto all leads and lifts.

Providing and fixing M.S. BP Sheet 2.00mm thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in charge (Base members of steel work shall be measured and paid separtely) including carriage of materials within all leads and lifts.

Providing and fixing ridges or hips 60cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20microns over 5microns primer coating + back coat of polyster of 5microns over 5microns primer coating i/c fixing with self drilling screws complete and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charge including carriage of materials upto all leads and lifts.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamal paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including carriage of materials within all leads and lifts;- With enamal paint other then white.

sat pal