SPL REPAIR TO BLDG NO SP 1 AND T 2 AND SPL REPAIR TO REPLACEMENT OF RUSTED CI GI PIPE WITH DI PPR PIPE AND ALLIED WORKS AT CERTAIN LOCATION AND SPL REPAIR TO CONVERSION OF HT LINE WITH HT UG CABLE AT BENGDUBI MIL STN UNDER GE BENGDUBI

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre-painted colored trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating, 550 MPA yield stress as per AS-1397), colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, as in roof covering/ cladding to wall, fixed with and including Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals), complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

S&F mild steel rolled sections [Fe 410-W (Gde E-250) quality - B] as in roof trusses (framed), trussed, main and cross beams, hip and jack rafters, purlins, Gusset plate and base plates, where connected to common rafters and running rails, distance pieces, cleats, guides for sliding doors; fixed with angle cleats or other connecting plates, framing for cladding, staging for water tanks, nuts, bolts, washers etc,includng welding or riveting etc, complete all as specified and as directed.

M&L for the Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed.

S&F anodised aluminium snap grid of size 605x605mm frame work for false ceiling hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out GI flat iron 40x3mm size 60mm long and fixed expansion hold fasteners 12.5mm dia and 40mm long,complete all as specified and as directed.

S & F 4mm thick Non-asbestos fibre cement decorative/designer building boards to steel frame work with screws in ceiling (flat and/or slopping) and including jointless finish with & also including joining compound and tape as per manufacturer instructions, including dismantling of wall and ceiling boards complete all as specified and as directed. Notes :- (i) The board shall be confirming to IS-14862 and shall be manufactured from the homogeneious mixture of cement, quartz and cellulose and shall be curred with high pressure steam using auto claving process.(ii) Aluminium frame work shall be measured and paid for separately.

Providing and fixing DESIGNER Pvc False Ceiling ,consisting of 6mm(+-0.25) thick hollow plain embossed PVC sheet of Manufactured by ISO 9001-2008, certifiedcompany, used as panel insert in a frame work made using anodised aluminium section in square pattern. The aluminium frame work is supported from the ceiling with the help of "J" hook and GI wire/6mm roads of require sizes to maintain proper level etc . The aluminium framwork is supported on side wall with the use of aluminium L-section of size 1"x1"(25mmx25mm) angles etc including dismantling of wall and ceiling boards complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M & L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles of size 300mmx 450mm , 6 to 7 mm thick on the vertical surfaces such as in skirting / dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the shade of the tiles, over and including 10mm thick cement mortal backing coat in CM (1:4), complete all as specified and and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & show on drawing for SI NO 8101 on Sr. Page No181 of SSR Part -II and as directed.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water etc, and also including removal of rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6), on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacturer instructions, complete all as specified and as directed. Note:- WPC shall be measured and paid seperately.

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 15 mm dia bore complete all specified .

Taking down steel tubing & connections including cleaning for refing serviceable pipe or removal balance pipe of 20 mm dia bore complete all specified .

S&F laying of CPVC pipes SDR 11& plain CPVC SDR 11 20mm outer dia laid in trenches/wall complete all as specifed

S&F laying of CPVC pipes SDR 11& plain CPVC SDR 11 25mm outer dia laid in trenches/wall complete all as specifed

S&F hard drawn steel wire fabric (weight not exc.4kg/Sqm) fixed in tank caging, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including disposing off the retrieved debris outside the premises, complete all as specified and as directed.

M&L for providing 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate), as in plinth protection, surface finished even & smooth without using extra cement including provision of 10 mm joints (at an interval of 3 metre and turnings) duly filled with fine sand and bitumen in the ratio of (3:1), complete all as specified and directed.

S&F in repair mild steel helical door spring 300mm long, ordinary rat tail rod pattern springs including roller and roller plate fixed with screw to wooden frame or with welding to steel frame, complete all as specified and as directed.

S & F in repairs stainless steel curtain rod of 25mm dia including six nos curtain ring per running meter complete all as specified and as directed.

M&L for preparing new Plasterd surfaces of walls duly applied 2mm wall care Putty and there after applying two coats of oil bound distemper, white or any tint as approved, over and including a coat of primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white washing, complete all as specified and directed .

M&L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer, complete all as specified and directed.

M&L for preparing new wooden surfaces of any description not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed .

S & F finial fancy type for curtain rod in pair etc complete all as specified and as directed.

M&L for 75mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub-base of flooring, etc, finished concrete surfaces even and rough to receive cement screed, complete all as specified and as directed.

Supply and fixing switch socket , 2 in 1, 5pin, 5 Amp, complete all as specified and as directed.

S&F switch socket outlet, 2 in 1, 6 pin, 5 and 15 amp, complete all as specified and as directed.

S&F ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting, complete all as specified and as directed.

S&F for stepped type electronic fan regulator, suitable flush type, complete all as specified and directed.

S&F sheet metal enclosure for MCBs DBs, TPN, 4 way with 200Amps rated bus bar 240 volts, Double Door with magnetic locking system, Powder coated including necessary provision for inserting the DBs in wall by cutting the bricks/stone masonary etc and making good of disturbed surfaces to match with existing colour of wall, complete all as specified and as directed.

S&F for sheet metal enclosure MCB, SPN, DB, 8 ways, 100 Amps rated bus bar 240V IP-43 IK 09 in double door, Aluminium Zinc coated hardware for rust proof longevility with magnetic locking system including provision for inserting the DBs in wall by cutting the brick/stone masonery etc andmaking good the disturbed surfaces in CM 1:3, complete all as specified and directed.

S & F MCB Three pole and neutral rated capacity 16 to 32 amp rating 240V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

S & F MCB single pole and neutral rated capacity 6 to 32 amp rating 240V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

S & F MCB single pole rated capacity 6 to 32 amp rating 240V, breaking capacity 10KA 'C' curve and current indication for individual pole and designed based on advanced current limiting hammer trip mechanism ,complete all as specified and directed.

Supply and fixing LED tube light batten type made of CRCA sheet with decorative end caps suitable with ultra bright glass LED tube light 1x18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/celling incl fittings accessories and connecting up with twin core fexible copper conductor cable suitable size all as specified.

S & F energy saving new generation enviromental friendly long life versatile presure die cast aluminium IP 66 for securty ligh fitting luninaire with high power LEDs as ligh source (100 Im/watt) with LDR sensor for automatic ON/OFF operation and electronic driver of capacity 25 watts with pre-wared and necessary mounting arrangements and provison of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade braket 1.5 mtr long bend to requred shape with clamps, nut botls including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer , complete all as directed by Engineer-in-charge.

Taking down ceiling fan/exhaust fan any sweep, keeping with safe custody and refixing the same with replacement of unsv 3core PVC insulated sheathed multistanded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal, complete all as specified and directed

S&F energy saving BLDC ceiling fan; 5 star rating, Type of motor - Brush Less DC Motor (BLDC) and Input Power - 32 to 35 Watts with full speed and reduced power consumption with reduced speed technology, Voltage- 90-300V AC, 50Hz, single phase, RPM - 340 to 375 rpm, Blades- Decorated, Sweep - 1200 mm, Air de

livery - Not less than 210 CFM with service value 6.00 BEE and Colour - Glow white/ Toast Brown/ Gloss Black or others as approved by GE, complete all as specified and as directed.

S & F for energy Exhaust fan of 300 mm sweep made of metal body Ventil Air-DS type complete with louver with botls nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted). complete all as directed and specified.

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing , high transmissitivity diffuser , high lumen output box type fitting , 230 volts and intregated electronic driver connector block etc , complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193from ceiling rose to fitting complete all as specified and as directed.

Material and labour for sub main wiring with 2 run of single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 6.0 sqmm and one single core PVC insulated (unsheathed) multi stranded copper conductor FRLSH cable of size 6.0sqmm as in continuous earth wire drawn into and including concealed PVC conduit, medium grade of 25 mm bore complete with fittings, PVC Junction Boxes, fixings accessories, also including cutting chases, pinning in, making good to facing and pointing in using cement mortar 1:3 and making good disturbed surfaces to match with the adjoining surfaces including taking down of existing old submain wire complete all as specified and as directed. Note:- For payment purposes, 2 runs of main cable (each of 1RM) 1 run of earth continuity cable (1RM) and one run of conduit (1RM) all together shall be considered as "1RM".

Taking down GI pipes 15 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 20 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 25 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 40 mm dia from trenches/walls/floor etc complete all as specified and directed.

Taking down GI pipes 50 mm dia from trenches/walls/floor etc complete all as specified and directed.

All as above item no 57 but tap 2 in 1 of 15mm bore complete all as specified and as directed.

All as per item No 91 here-in-before but for one 3pin 5 Amp switch socket outlet, independent board , complete all as specified and as directed.

All as per item No 91 here-in-before but for one fan point/exhaust fan point contrilled by one switch on the same board complete all as specified and as directed.

All as per item No 91 here-in-before but for one 3pin 5 Amp switch socket outlet,same board complete all as specified and as directed.

All as per item No 91 here-in-before but for one 5/15 Amp switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLSH) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLSH) cable for earth continuity wire, complete all as specified and as directed.

All as per item no 121 above but 20 mm Bore.

Taking down CI pipes 80 mm dia from trenches/walls/floor etc complete including all joints all as specified and directed.

Taking down CI pipes 100 mm dia from trenches/walls/floor etc complete including all joints all as specified and directed.

M&L for steel water tubing medium grade galvanised with new fitting laid in trenches 15mm bore :-

S&F PPR (Poly Propylene random co-polymer) pipe size 110 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 90 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 50 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

S&F PPR (Poly Propylene random co-polymer) pipe size 40 mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

All as per item no 121 above but 25 mm Bore.

S&F PPR (Poly Propylene random co-polymer) pipe size 25mm OD, PN-10 (SDR-11) IS-15801, 3-layer (outer green coloured UV stablized, middle black coloured UV stablizer and innermost layer white coloured with anti-microbial property) having thermal stability for hot & cold water supply with and including all necessary including all fitting such as elbow, tee, socket, bends, union joint etc complete all as specified and directed.

Taking down CI pipes including all fittings of 150mm bore including checking and segregation of serviceable pipe and keep the serviceable pipes & Lead in safe custody for cleaning and refixing complete all as specified and as directed.

All as per item no 121 above but 40 mm Bore.

All as per item no 121 above but 50 mm Bore.

Supply, Jointing and laying in trenches in standard length , centrifugally cast ( spun ) ductile iron ( DI ) pressure pipes,with inside cement mortar lining and black bitumen external coating, nominal diameter, class K-7 classification, confirming to IS-8329 ISI marked , including pushon and rubber gasket joints and jointing necessary DI specials etc including testing, complete for 100mm bore all as specified and as diercted.

All as per item no 121 above but 80 mm Bore.

All as per item no 121 above but 100 mm Bore.

All as per item no 134 above but 150mm bore

Taking down unserviceable CI sluice valve 80 mm to 150mm dia complete all as directed.

All as per item no 137 above but 150 mm bore

Supply and fixing Sluice valve cast iron confirming to IS : 14846 both end flanged with S/S spindle with nut class PN:1.6 with ISI marked complete with hand wheel nuts, bolts, washers & rubber gusket etc of following the sizes complete for 80mm bore all as specified and directed.

Supply and fixing in repair Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore.

Supply and fixing in repair Float valve from PVC Tank with fittings,for iron pipe and fixed for 20 mm bore.

Supply and fixing in repair Float valve from PVC Tank with fittings,for iron pipe and fixed for 20 mm bore.

M&L for construction of brick masonry valve pit of size 1200x1200x900mm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in foundation, and 15mm thick rendering in cement mortor (1:4) internally, externally up to 15cm below GL, providing valve pit cover made of 3 mm thick MS sheet/plate, welded with 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embeded in PCC 1:2:4 type B-1 (20mm graded aggregate) block of size 230 x 200 x 100mm and provision of hinges, handle and locking arrangement including two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer and necessary excavation and earth work in soft/loose soil including dismantling of existing valve pit complete all as specified & directed.

M&L for construction of brick masonry valve pit of size 900x900x900mm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in foundation, and 15mm thick rendering in cement mortor (1:4) internally, externally up to 15cm below GL, providing valve pit cover made of 3 mm thick MS sheet/plate, welded with 40 X 40 X 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embeded in PCC 1:2:4 type B-1 (20mm graded aggregate) block of size 230 x 200 x 100mm and provision of hinges, handle and locking arrangement including two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer and necessary excavation and earth work in soft/loose soil including dismantling of existing valve pit complete all as specified & directed.

Dismantling of cross arms, bracings, supports, clamps and back plates fabricated from angle sections sectio

ns including nuts, bolts, washers, complete all as specified and directed.

All as per item no 137 above but 100 mm bore

Dismantling ACSR or AAC conductor any type & any size and removing from site complete all as specified and directed.

Dismantling of GI earth wire from any position all as specified and directed by Engr-in-Charge.

Excavation in trenches in soft/loose soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation,laying of cable, pipe etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out, complete all as specified and directed.

Removal of surplus soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Returning, filling in, including spreading, watering and well ramming in layers not exc 25cm thick in layers in soft/loose soil, complete all as specified and directed.

M& L for fine Sand cushioning in trenches for cushioning of underground cable including spreading, levelling, well ramming in layers , complete all as specified and directed. Note: Punned thickness 18cm shall be considered for payment as per para 19.75 of SSR Part-I)

Supply & Laying in Trenches unreinforced precast concrete cable cover ,class HV type-l flat ,size 300x180x40mm conforming to IS 5820-1978 for cable protection complete all as specified and as directed.

Supply and fixing in trenches GI pipe 100 mm bore light grade for protection of U/G cable complete all as specified and as directed.

Supply and installation (above ground) including testing HT joint box 2 way outdoor type of size 1200 x900 x 900 mm (overall) made out of 3.15mm thick CRCA sheet with support of angle iron frame of size 40 x40x6mm with KIOSK BOX inner box of suitable size and comprising of 03 Nos HT porcelain bushing and copper round bus bar 12mm dia rigidly mounted on bakelite sheet 12mm thick to support insulators of suitable size and shape including providing necessary electric connection and applied two coats of synthetic enamel paint over a coat of red oxide primer to steel surface (int & Externally) including PCC 1:3:6 type C1 Using 20mm graded stone aggregate complete including necessary excavation and earth work for foundation and necessary electric connection coplete and including dismantaling of unserviceable joint box complete all as specified and as directed.

Supply and installation (above ground) including testing HT joint box 3 way outdoor type of size 1500 x1000 x 900 mm (overall) made out of 3.15mm thick CRCA sheet with support of angle iron frame of size 40 x40x6mm with KIOSK BOX inner box of suitable size and comprising of 03 Nos HT porcelain bushing and copper round bus bar 12mm dia rigidly mounted on bakelite sheet 12mm thick to support insulators of suitable size and shape including providing necessary electric connection and applied two coats of synthetic enamel paint over a coat of red oxide primer to steel surface (int & Externally) including PCC 1:3:6 type C1 Using 20mm graded stone aggregate complete including necessary excavation and earth work for foundation and necessary electric connection coplete and including dismantaling of unserviceable joint box complete all as specified and as directed.

M&L for Cable jointing kit for 11 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm including testing complete all as specified and as directed.

M&L Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 sqmm to 95 sqmm including testing complete all as specified and as directed.

M&L Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armourend aluminium conductor cable of size 50 sqmm to 95 sqmm including testing complete all as specified and as directed.

S & F erecting steel tubular pole , swaged complete with cast iron base plate finial taper plug bolts, nuts, washer and screws including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminous paints to portion embedded in PCC including numbering of poles with two coats of synthetic enamel paints , type 410-SP-55 (11 mtr long) complete Note:- Excavation & Earth work and PCC foundations/base shell be measured amd paid separately under relevant items of this BoQ.

M & L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of preparation of exposed surfaces, application of one coat of red oxide primer and thereafter 2 coats of alluminium paint, complete all as specified and directed.

Supply and fix in repair Pin type, polymer type insulator including two galvanised iron washers and one galvanised iron nut, 150mm height, 150mm dia for 11000 volts grade, complete all as specified and directed.

Supply and fixing in replacement of vertical type switch air break gang operated switch tripple pole mechanically operating mounted on insulator and steel frame with operating mechanism worked from ground level for current rating up to 200 Amps and working pressure of 11000 volts grade consisting of 4 insulator per pole with GI medium grade operating handle and locking arrangements fixed with down rod operating brackets, complete all as specified and as directed.

PRICE SCHEDULE (a) (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) (b) Estimated rate Column is for Department use only. (Note: Credit amount if any vide Credit schedule shall be deducted from the total quoted amount of Sch 'A' to arrive total contract sum.) (c) The Tenderers attention is drawn to the fact that the Work Order No 1 shall be placed after submission of performance security of requisite amount in favor of Accepting Officer.