DEVELOPMENT OF TOURIST FACILITIES AT SONEPUR MELA GROUND, SARAN IN BIHAR.

BIHAR STATE TOURISM DEVELOPMENT CORPORATION LIMITED

Technical Sheet

Name of Work DEVELOPMENT OF TOURIST FACILITIES AT SONEPUR MELA GROUND, SARAN IN BIHAR Cost of Work as per BOQ(Rs in Lakhs) 2310.72558 Time of Completion in months 12 ALL COLOURED CELL TO BE FILLED ACCORDINGLY

Sactioned Amount 242857000 Date of Sanction 2026-06-01T00:00:00Z Date of Tender 2026-05-15T00:00:00Z

Sl No. Items Requirement Cl. No. Name of the Contractor

Address of the Contractor

1 Registration No.

2 Bid Validity Bids shall remain valid for a period not less than 120 days after the deadline date. A Bid valid for a shorter period shall be rejected by the Employer as non-responsive 120 Days 15.1 Bid validity periods In days

3 Bid Security (A) Online mode i.e. internet payment gateway (credit/ debit card), Net Banking, NEFT/ RTGS 16.1 Amount To be entered (Rs in Lakhs)

(B) Unconditional bank guarantee from any scheduled Indian bank issued within the state in the format given (If issued from any bank outside state will be converted to any bank within the state before executing the agreement. Amount To be entered (Rs in Lakhs)

Bid Security Amount - (Rs. In Lakhs) 33.3 Bid Security Amount - Rs.

4 (i) Legal Status of Bidder. 4.3(a)

(ii) Place of Registration.

(iii) Principal place of Business

(iv) Power of attorney of signatory Bid Attached or Not 4.2(iv)

5 Total value of civil engineering construction work performed in last five years. 1. Annual Financial Turn Over usually not less than 50 % of the estimated annual payments under the contract (Rs in Lakhs) APPENDIX to ITB

2020-21 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.469

2021-22 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.36

2022-23 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.26

2023-24 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.166

2024-25 Amount To be entered (Rs in Lakhs)

Escalation Factor= 1.08

6 Work Experience of Similar nature Satisfactory completed atleast one similar work of value not less than 50 % of estimated value of contract (Rs in Lakhs) 4.5 (b) Amount To be entered (Rs in Lakhs)

7 Minimum Quantities of work done as prime contractor in any one year during last five years. Items Unit Total Quantity 4.5 ( c )

Brick Work cum 876.21 Value to be entered in unit cum

Electrical Works Rs. 17772618 Value to be entered in Rs.

PHE Work Rs. 3539046 Value to be entered in Rs.

PCC&RCC cum 1633.56 Value to be entered in unit cum

Steel MT 162.79 Value to be entered in MT

Flooring Work. (Any Stone, Granite, Kota, Sand Stone etc.) sqm 6342.38 Value to be entered in unit sqm

8 Bidding Capacity More than the total Bid value of present work = A*N*3-B=Rs. ____.Where A = Maxm. Value of work executed in any one yr during last 5 yrs. N= Nos of years for completion of works. B=Value of existing commitments & ongoing works to be completed in period (Rs in Lakhs) 4.4

9 (a) Existing commitments and ongoing works Amount To be entered (Rs in Lakhs)

(b) Work for which Bid already submitted Amount To be entered (Rs in Lakhs)

10 Availability of key items of Contractor's Equipment Type of Equipment/Maximum age No. Required Nos. Max. Age Page-17 Nos./ Max. Age

Front end Loader 1 5

Plate Vibrator 2 5

Niddle Vibrator 2 5

Water tankar 2 5

Steel shuttering 2500sft 5 to 7

Concrete Mixture 1 5

11 Key Personnel Personnel/Qualification/Contract Package Size (Rs. 10 to 30 Crore) Page-18 Name of the Personnel and Experince in years

Project Manager/ B.E. Civil + 10 Years Exp. (5 years as Manager) or retired E.E. 1 No.

Site Engineer/ B.E. Civil + 07 Years Exp. (3 years in Building Construction) or retired A.E. 1 No.

Plant Engineer/ B.E. Civil + 05 Years Exp. or Dip. Electrical + 07 Years Exp. or Retired J.E. 1 No.

Site Supervisor/ Fresh Graduate in Civil or Diploma Civil + 03 Years Exp. or retired I.T.I Holder. 2 Nos.

12 Evidence of accesses to Financial Resources Evidence of access to or availability of creadit facilities (10% of estimated cost), certified by bankers (Not more than 3 months old). (Rs in Lakhs). 4.2(i) Amount To be entered (Rs in Lakhs)

13 Proposed methodology and programme of construction. Justifying their capability of execution and completion of the work as per technical specifications within the stipulated period of completion as per milestones. (Attached or not) 4.3(l)

14 Litigation History Information regarding any litigation, current or during the last five years, in which the Bidder is involved, the parties concerned, and disputed amount. (Attached or not) 4.3(j)

15 Affidavit Regarding statements made in the required attachments are true and correct. Page-24

16 Undertaking Able to invest a minimum of cost upto 25% of contract value of work. During implementation of contract. (Rs in Lakhs). 4.2(ii)

17 NOC for Debar (Affidavit)

BIHAR STATE TOURISM DEVELOPMENT CORPORATION LTD.

(A GOVERNMENT OF BIHAR UNDERTAKING)

DEVELOPMENT OF TOURIST FACILITIES AT SONEPUR MELA GROUND, SARAN IN BIHAR

QUOTING SHEET FOR BIDDERS

Name of Contractor

Address of Contractor

E-mail ID of Contractor Mobile Number

NIT -08/E-TENDER/ BSTDC/SBD/2026-27

Sl No. Description Estimated Amount Rate Quoted by Contractor

% Above/Below TOTAL QUOTED AMOUNT Rs.(In Figure) TOTAL QUOTED AMOUNT Rs.(In Words)

1 Total Schedule Amount (Rs.) 138508169

2 Total Non-Schedule Amount (Rs.) To be Quoted !

TOTAL AMOUNT Rs. 231072558

Development of Tourist Facilities at Sonepur Mela Ground, Saran, Bihar

Bill of Quantity

S. No Sl. No./ Code. SOR- Description of Work Unit Qnty Rate (Rs) Amount (Rs.)

PART-A CIVIL SOR ITEMS

2.29 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cmdeep and disposal or rubbish ,lead up to 50 m lift up to 1.5 m

0.0 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

2 2.6.1 All kinds of soil Cum 3698.02 314.9 1164506.498

3 2.28 Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. Cum 5973.32 287.3 1716134.836

0.9 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap.)

0.0 Concrete Work

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

5 4.1.6 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size) Cum 656.54 3279.8 2153319.892

6.1C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

6 6.1.14C Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work Cum 1670.7125 4923 8224917.6375

7 6.45.2 Cement mortar 1.:4 (1 cement: 4 coarse sand ) Sqm 81.7 700.8 57255.36

0.0 Reinforced Cement Concrete Works

0.0 Centring and shuttering including strutting, propping etc. and removal of form for:

8 5.9.1 Foundations, footings, bases of columns, etc., for mass concrete. Sqm 1720.04 211.6 363960.464

9 5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 3803 437.5 1663812.5

10 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 2086.82 404.7 844536.054

11 5.9.6 Columns, Pillars, Piers, Abutments, Post and struts Sqm 2541.02 494.4 1256280.288

5.22 Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars

5.33 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and including retard setting of concrete, improve work ability without impairing strength and admixtures in recommended proportions as per IS: 9103 to accelerate, reinforcement, durability as per direction of Engineer-in charge.

16 5.33.1 All work upto plinth level Cum 1210.1 5063.4 6127220.339999999

17 5.33.2 All work from plinth level upto floor V level. Cum 1355.44 5863.2 7947215.808

0.0 Flooring Works

18 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I. Sqm 12684.75 283.3 3593589.6750000003

11.78 Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc.complete as per manufacturer’s specifications & direction of Engineer-in-Charge. 60mm thick C.C.paver block of M-35 grade with approved colour, design & pattern.

16.69 Providing and laying at or near ground level Factory made kerb stone of M-25 gade cement concrete in position to the required line levl and curvature jointed with cement mortar 1:3(1 cement:3 coarse sand) including making joints with or without grooves (thickness of joint except at sharp curve shall not to more than 5 mm)including making drainage opening wherever required completred etc.as per direction of engineer in charge (length of finish kerb edging shall be measured for payment)(Precast C.C kerb stone shall be approved by Engineer in charge)

20 For Green Area A Cum 3.375 7998.8 26995.95

4.9 Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S.Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S.Pipes 40 mm dia and 450 mm long with 150x150x6mm M.S.plate welded at bottom and embedded 150 mm in cement concrete 1:3:6 (1Cement :3coarse sand (zone-III) derived from natural sources : 6graded stone aggregate 20 mm nominal size derived from natural sources), including necessary excavation of size 250x250x450 mm deep for the same in bitumen / concrete pavement at specified spacing

21 In Parking Nos 250 588.6 147150

11.3 40 mm thick fine dressed stone flooring over 20 mm (average) thick base with joint finished fiush:base 1:5 (1 cement: 5 coarse sand )with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.

7.37 Stone work ( machine cut edges veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately

23 7.37.1.A Dressing of sand stone in veneer work Sqm 1375.2 2563.8 3525737.7600000002

8.12 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (avearage) thick base of cement mortar 1:4 (1cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

24 (a) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm 1279.17 2147.7 2747273.409

11.41A Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the anufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.1 Double charge vitrified tile polished finish of size

11.41A Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.1 Double charge vitrified tile polished finish of size

27 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (Thickness to be specified by the manufacture) of approved make inall colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement Motar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete Sqm 141.7 795 112651.49999999999

8.13 Providing and laying Polished Granite Store Flooring In required design and patterns , linear as well as curvilinear portion of the thick stone slab over 20mm (average)thick base of cement mortary 1:4(cement :4 coarse sand)laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing curing and polishing etc.all complete as specified an as directed by the Engineer in Charge

28 8.13.1 Polished Granite Stone slab jet black Cheary Red ,Elite Brown Cat Eye or equivalent. Sqm 279 3605.2 1005850.7999999999

0.0 Aluminium Work

0.0 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up tandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, traight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

29 21.1.2.3 Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) KG 577.9575 480 277419.6

30 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture ,including providing and fixing top & bottom pivot &spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete asper direction of Engineer-in- charge (Door handle,lock and stopper etc.to be paid separately). Sqm 8.16 5143 41966.88

31 10.18 Providing and fixing circular/ hexagonal cast iron or M.S sheet box for ceiling fan clamp 140mm internal dia, 73mm height, 5mm thick rim bottom and top lids,1.5mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3mm dia round headed screws, one lock at the corners.Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. Num 311 165.4 51439.4

10.32 Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

32 10.32.2 In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works. KG 6494.4 114.6 744258.2399999999

10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel rimer, including welding and bolted with special shaped washers etc. complete

33 10.16.1 Hot finished welded type tubes KG 2776.33 123.9 343987.287

0.9 Supplying and fixing Rolling sutters of approved make.made of required size of M.S. laths inter locked together through their intire length and jointed together at the end by locks mounted on specially designed pipe shaft with brackets, side guides and arragments for inside and out side locking with push and pull operation complete including the cost of providing and fixing necessery 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

34 10.6.1 80x1.25mm M.S laths With 1.25mm thik top cover. Sqm 1134 2673.7 3031975.8

35 7.42 Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge Each 750 265 198750

36 9.145 Providing and Fixing factory made PVC door frame made of PVC extruded sections of size75 mm x53mm, having wall thickness 2.0 mm (±0.2mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28mm x 30mm x 2mm thickness (±0.2mm) and 75mm x 200mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut jointed and fusion welded together, including providing and fixing 3 nos of 125mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer’s specification and direction of engineer-in charge. MTR 86.4 582.3 50310.72

37 0.000 Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after in serting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer’s specification and direction of engineer-in charge. Sqm 38.4 3792.5 145632

9.147E Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 min height dimension comprising of uPVC multi-chambered frame with in-built roller track and sas hextruded pro filed uly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape& size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inlines as had aptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wiremesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100x8mm sizefor fixing frame to finished wall and necessary stainless steel screws etc .Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hard ware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes ,wiremesh and silicon sealent shall be paid separately). Note: For uPVC frame and sas hextruded profiles minus 5% to lerance in dimension i.e. in depth & width of profile shall be acceptable.

38 9.147E.1 Two track two panels sliding window madeof (big series) frame 67x50mm & sash 46x62mm both having wall thickness of 2.3±0.2mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) Sqm 45.9 7239.1 332274.69

0.0 Plaster And Finishing Work

13.11 12 mm cement plaster of mix

13.24 6 mm cement Plaster to ceiling of mix

40 13.24.2 1:4(1 cement;4 coares sand) Sqm 3803 125.6 477656.8

41 13.80A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Sqm 16430.7 105.4 1731795.7800000003

13.46.A Finishing walls with Premium Acrylic smooth exterior paint with silicone additives of required shade.

42 13.46A.1 New work (Two or more coats applied @ 1.43 ltr / 10 sqm. Over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm). Sqm 12856.7 132.5 1703512.75

13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

43 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Sqm 7077 117.3 830132.1

0.0 Repair Work

13.45 Finishing walls with textured exterior paint of required shade :

44 13.45.1 New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm Sqm 140 215.2 30128

13.94 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

45 13.94.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. Sqm 280 116.5 32620

46 14.43 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Sqm 280 7.7 2156

12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointingcompound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutoutsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

47 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I Sqm 550 828.2 455510

0.0 Water Proofing Treatments Work

0.0 Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water-proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing applying a secoung coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300 x 300 mm square. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and specifed by the Engineer-in-Charge

48 22.8.1 With average thickness of 120 mm and minimum thickness at khurras point to be 65 .. Sqm 3803 850.7 3235212.1

0.0 Dismantling And Demolishing

0.9 Demolishing cement concrete including disposal of material within 50 metre lead:

50 15.3 Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material withing 50 metres lead: Cum 25.5 1411.2 35985.6

15.13 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead.

51 15.13.1 Of area 3 sqm and below Each 4 58.9 235.6

15.7 Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead:

52 15.7.4 In cement mortar Cum 26.25 823.7 21622.125

15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

53 15.23.2 For thickness of tiles above 25 mm and upto 40 mm Sqm 37.5 47.5 1781.25

54 15.6 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. Cum 112.5 219.3 24671.25

0.0 Horticulture And Landscaping

55 23.1 Trenching in ordinary soil upto adepth of 60 cm including removal and stacking of service able materials and thendis posing of by spreading and neatly levelling with in alead of 50 mand making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooding trench with water (encluding cost of imported earth,sludge or manure) Sqm 642 44.7 28697.4

56 23.2 Supplying and stacking of good earth at site including royalty but excluding carriage earth measusred in stacks will be reduced by 20% for payment) Cum 192.6 143.5 27638.1

57 23.3 Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment). Cum 96.3 282.6 27214.38

23.4 Supplying and stacking a site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

58 23.4.1 Screened through sieve of l.S. designation 20 mm Cum 96.3 278.9 26858.069999999996

59 23.5 Rough dressing the trenched ground including breaking clods. 100 Sqm 6.42 85.9 551.4780000000001

60 23.6 Uprooting weeds form the trench edarea after 10 to 15 days of its flooding with water including disposal of uprooted vegetation. 100 Sqm 6.42 283.2 1818.144

61 23.7 Fine dressing the ground 100 Sqm 6.42 208.8 1340.496

62 23.8 Spreading of sludge , dump manure or /and good earth inrequired thickness (Cost of sludge,dump manure or /and good earth tobe paid separately). Cum 96.3 30.1 2898.63

63 23.9 Mixing earth and sjudge or manure in porportion specified or directed. Cum 385.2 20.9 8050.679999999999

23.1 Grassing with 'Doob' grass including water In gand maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weed sand fit formo wing including supplying good earth if needed.

64 23.10.2 In rows 7.5 cm apart in either direction. 100 Sqm 6.42 670.8 4306.536

65 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clod sand mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20 %: one part of stacked volume of sludge or manure after reduction by 8% ). flooding with water, filling with earth if necessary , watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as drected, with in a lead of 50 mli ft upto 1.5 m complete (cost of sludge,manureor extra earth to be paid for separately). Cum 71.82 126.9 9113.957999999999

23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludg einthe ratio of 2;1 by volume (2 parts of stacked volume of earth after reduction by 20%: 1 part of stacked volume of manure after reduction by 8%) flooding with water ,dressing including removal of rubbish and surplus earth, if any with all lead sandl if ts (cost of manure, sludge or extra good earth if needed to be paid for separately):

66 23.14.1 Holes 1.2 m dia, And 1.2 m deep. Each 10 536.5 5365

67 23.14.2 Holes 60 cm ciia. And 60 cm deep Each 20 69.3 1386

68 23.2 Filling mixture of earth and sludge or manure in the deisired proportion in trenches, flooding with water and levelling (cost of supplying earth and sludge or manure and mixing excluded). Cum 385.2 10.3 3967.56

69 23.24 Flooding the ground with water including making kiaries and dismantelling the same 100 Sqm 6.42 171.4 1100.388

Part-B Trees, Plants, Shrubs And Creepers

A Boundary Wall

70 5.12 Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. Each 15 322.9 4843.5

71 9.3 Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. Each 20 40 800

72 9.12 Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge Each 20 25 500

73 9.14 Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. Each 25 25 625

74 5.7 Providing and Displaying Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. in 25 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. Each 50 461.25 23062.5

75 5.31 Providing and Displaying Furcaira variegated well developed with fresh & healthy foliage 8 to 10 leaves in 30 cm Earthen Pot as per direction of the officer-in-charge. Each 20 225.5 4510

76 5.37 Providing and Displaying Phoenix roebelenii palm well developed having 20 to 25 fresh & healthy leaves 90 to 105 cm ht. in 30 cm Cement Pot as per direction of the officer-in-charge. Each 15 538.15 8072.25

77 6.8 Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each 60 20 1200

78 6.11 Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 25 30 750

79 6.24 Providing and stacking of Setcreasea purpurea full of variegated leaves in 15 cm size of Earthen Pot/Plastic Pot as per direction of the officer-in-charge Each 25 20 500

80 7.1 Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. Each 20 180 3600

C Entrance Step

81 5.3 Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. Each 15 41 615

82 5.14 Providing and Displaying Cycus revoluta in 35 cm challi, specimen , having 30 to 40 with fresh and healthy, leaves having 25cm to 30cm circumfrance of base stem well developed as per direction of the officer-in-charge. Each 20 1183.9 23678

83 5.29 Providing and Displaying Fishtail palm well developed with fresh & healthy foliage leaves of ht 210 to 240cm Specimen in 35 cm Cement Pot as per direction of the officer-in-charge Each 25 307.5 7687.5

84 5.31 Providing and Displaying Furcaira variegated well developed with fresh & healthy foliage 8 to 10 leaves in 30 cm Earthen Pot as per direction of the officer-in-charge. Each 25 225.5 5637.5

85 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. Each 100 20 2000

86 6.24 Providing and stacking of Setcreasea purpurea full of variegated leaves in 15 cm size of Earthen Pot/Plastic Pot as per direction of the officer-in-charge Each 50 20 1000

87 8.25 Providing and stacking of Ficus panda of height 30-45 cm. with 3-4 branches and healthy foliage in p.bag of size 20 cm as per direction of the officer-in-charge. Each 20 35 700

0.0 HORTICULTURE CARRIAGE

93 2 DUMP MANURE Cum 96.3 187.54 18060.102

95 4 NEEL GIRI/MAXICAN GRASS TURF Sqm 5271 4.2 22138.2

96 Add 5.36% GST on SOR item As Per BCD 5875350.578756709

97 SIGNORANCE FEE 646770.72617824

PART-B PLUMBING SOR ITEMS

17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

98 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps nos 22 2764.4 60816.8

99 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. nos 22 1068.5 23507

17.2 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

100 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid nos 11 4230 46530

17.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

101 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests nos 10 4470.9 44709

17.4 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

102 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern nos 10 3723.2 37232

103 17.72 Providing and fixing white vitreous china flat back or wall corner type lipped roviding and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms nos 10 204.7 2047

8.1 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and

104 8.10.1 White Agaria Marble Stone sqm 25 3061.2 76530

105 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. nos 10 146.3 1463

18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

106 100 mm diameter nos 10 166.3 1663

18.58 Providing and fixing PTMT grating of approved quality and colour.

18.58.1 Circular type

107 18.58.1.1 100 mm nominal dia nos 26 33.2 863.2

0.00_ Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

17.60.1 100 mm inlet and 100 mm outlet

108 17.60.1.1 Sand cast iron S&S as per IS: 3989 nos 26 1129.2 29359.2

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.35 Providing and fixing soil, waste and vent pipes :

111 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 Metre 220 978.3 215226

17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

112 17.38.1.1 Sand cast iron S&S as per IS - 1729 each 150 530.7 79605

17.39 Providing and fixing plain bend of required degree..

113 17.39.1.1 Sand cast iron S&S as per IS - 1729 each 120 457.2 54864

17.41 Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :

114 17.41.1.1 Sand cast iron S&S as per IS - 1729 each 120 1038.8 124656

17.42 Providing and fixing double equal plain junction of required degree.

115 17.42.1.1 Sand cast iron S&S as per IS - 1729 each 110 861.2 94732

17.43 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

116 17.43.1.1 Sand cast iron S&S as per IS - 1729 each 130 671.2 87256

17.44 Providing and fixing single equal plain junction of required degree :

117 17.44.1.1 Sand cast iron S&S as per IS - 1729 each 150 580.2 87030

17.53 Providing and fixing sand cast iron S&S off sets as per IS-1729

17.53.1 76 mm off sets

17.53.1 114 mm off sets

119 17.53.2.2 With 100mm dia pipe Each 50 560.1 28005

17.53.3 152 mm off sets

120 17.53.3.2 With 100mm dia pipe Each 50 666.3 33315

17.55 Providing and fixing door piece, insertion rubber washer 3 mm thick, bolts & nuts complete.

121 17.55.1.1 Sand cast iron S&S as per IS-1729 Each 60 711.3 42678

17.56 Providing and fixing terminal guard:

122 17.56.1.1 Sand cast iron S&S as per IS-1729 Each 50 392.9 19645

17.57 Providing and fixing collar

123 17.57.1.1 Sand cast iron S&S as per IS-1729 Each 30 399.6 11988

17.58 Providing lead caulked joints to sand cast iron / centrifugally cast (spun) iron pipes and fittings of diameter.

17.59 Providing and fixing M.S stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter:

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

126 18.8.1 15 mm nominal outer dia Pipes Metre 100 278.2 27820

127 18.8.2 20 mm nominal outer dia Pipes Metre 70 350.8 24556

128 18.8.3 25 mm nominal outer dia pipes Metre 50 463.1 23155

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

129 18.7.2 20 mm nominal outer dia Pipes Metre 50 233.9 11695

130 18.7.3 25 mm nominal outer dia Pipes Metre 50 317.3 15865

131 18.7.4 32 mm nominal outer dia Pipes Metre 30 395.2 11856

132 18.7.5 40 mm nominal outer dia Pipes Metre 45 538.4 24228

133 18.7.6 50 mm nominal outer dia Pipes Metre 350 791 276850

18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

134 18.17.1A 20 mm nominal bore. nos 10 465.4 4654

135 18.17.1 25 mm nominal bore nos 10 532.3 5323

136 18.17.2 32 mm nominal bore nos 10 589.9 5899

137 18.17.3 40 mm nominal bore nos 10 707.3 7073

138 18.17.4 50 mm nominal bore nos 10 878.2 8782

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

139 18.18.1 15 mm nominal bore nos 50 348.9 17445

140 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. per liter 40000 9.7 388000

0.00_ Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts,nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

141 18.60.1 50 mm dia nominal bore each 2 3533.7 7067.4

142 18.65 Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms. Each 10 96.8 968

18.75 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.

143 18.75.3 25mm nominal bore, weighing not less than 62 gms each 10 100.6 1006

144 18.77 Cutting holes up to 15 x 15 cm in R.C.C floors and roofs for passing drain pipe and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof. Each 10 217.1 2171

17.34 Providing and fixing toilet paper holder :

146 17.22A Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. nos 32 886.2 28358.4

18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

148 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : nos 40 434.2 17368

18.32 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation,foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :

149 18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 100A No 20 1177.9 23558

2.1 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:

2.10.1 All kinds of soil

150 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia Metre 1500 391.7 587550

12.78 Providing and fixing on wall face PVC (working pressure 4kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

151 12.78.2 110 mm diameter Metre 800 257.5 206000

12.79 Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

12.79.1 Coupler

12.79.2 Single pushfit Coupler:

12.79.3 Single tee with door

12.8 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50 x 50 x 50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

157 12.81 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. Each 35 47.9 1676.5

19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

162 19.4.1 100x100 mm size P type

163 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 3 1860.6 5581.799999999999

0.0 Providing, laying and jointing glazed stoneware pipes class 'SP1' with stiff mixture of cement mortar in the proportion of 1:1(1 cement: 1 fine sane) including testing of joints etc. complete.

164 19.1.2 150 mm diameter Metre 10 464.3 4643

0.0 Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coase sand: 10 graded stone aggregate 40 mm nominal size) all-round S.W pipes including bed concrete as per standard design.

165 19.3.2 150 mm diameter S.W. pipe Metre 10 311.4 3114

19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

166 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 4 7914.7 31658.8

19.9 Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design

19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

167 19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 1 7090 7090

168 19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be isible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. each 150 310.9 46635

19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

169 19.19.3.1 Circular shape 560 mm internal diameter each 5 985.1 4925.5

19.27 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :

170 19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 50 3743.3 187165

19.29 Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design :

171 19.29.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 25 7186 179650

0.0_ Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

24.1.1 All types of soil

0.0_ Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

173 24.3.3 200 mm nominal size dia mtr 300 940.8 282240

174 24.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. cum 160 1188.9 190224

175 24.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. cum 160 1195.6 191296

176 24.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. cum 160 1195.6 191296

177 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. cum 160 1343.2 214912

PLUMBING BORING

24.1 Boring/drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. (All types of soil)

24.2 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools,plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

24.3 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC (UPVC) medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

181 24.3.2 150 mm nominal size dia P/M 0.0 660.1 198030

182 24.3.1 100 mm nominal size dia P/M 0.0 546.1 163830

24.4 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC (UPVC) medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

183 24.4.1 100 mm nominal size dia P/M 0.0 573.1 171930

24.13 Supplying the following fittings & fixing the same in position as per approved lowering assembly and strata chart including providing all equipments and welding the same on process of lowering the assay etc. all complete as per S/D of E/I.

184 24.13.2 150 mm dia well cap Each 2 210.7 421.4

24.14 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

185 24.14.2 (b) 150 mm dia M.S. Clamp 1.6 M long (one Pair) Each 2 1531.4 3062.8

24.15 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

186 24.15.1 100mm dia & 6mm thick M.S. well shoe plug Each 2 228.3 456.6

187 24.6 Providing all materials, labours, & equipments for fixing tube well with pea gravel of Dalbhumigarh to size 4mm to 8mm approx. as suitable for strata including carriage washing, placing and packing the same in position around the tube well etc. all complete as per direction of E/I. P/M3 0.0 1195.6 21520.8

188 NS-1 Transportation of drilling plants, developing equipments & all other required tools and M/c by and suitable mechanical means including all cost of loading, unloading, placing at work site and back after completion of work as per S/D of E/I Each 4 10640 42560

189 NS-2 Supplying all materials and labours for arrangement for additional water required during the drilling period for 70 Hrs & site clearance & leveling etc. And providing the soap duster etc. to staff engaged in drilling etc. all complete work as per specification & direction of E.I. Each 4 7980 31920

190 Add 5.36% GST on SOR item As Per BCD 335538.412

PART-C ELECTRICAL SOR ITEMS

1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch ,modular plate suitable size G.I box etc as per requred.

192 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. Metre 5500 309 1699500

0.0_ Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

193 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 3000 201 603000

194 1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 2000 246 492000

195 1.7.3 2X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 220 309 67980

195 1.7.4 2X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 5300 422 2236600

1.21 Supplying & fixing of following size medium class PVC conduit along with accessories in surface/ recess including cutting of wall and making good the same in case of recessed conduit as required.

1.24 Supplying and fixing following modular switch/ socket on the existing modulor plat & switch box/ including connections but excluding modular plate etc .as per required etc.

198 1.24.1 5/6 amps switch Each 241 82 19762

199 1.24.2 2 way, 5/6 amps switch Each 20 131 2620

201 1.24.4 3 pin , 5/6 amps socket outlet Each 241 112 26992

202 1.24.5 6 pin , 15/16 amps socket outlet Each 315 183 57645

203 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as required. Each 185 358 66230

204 1.26 Supplying and fixing modular blanking plate on the existing modular plate & metal box excluding modular plate, etc. as required. Each 150 34 5100

1.27 Supplying and fixing following size/ modules, Gl box along with modular base and cover plate for modular switches in recess etc as required.

211 1.33 Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. Each 150 64 9600

212 1.34 Supplying and fixing batten/ angle holder including connection etc. as required. Each 150 80 12000

1.59 Wiring for group controlled (looped) light point/ fan point/ exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit etc as required.

2.4 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

214 2.4.7 4OO A, 50 KA, FPMCCB Each 1 45651 45651

215 2.4.20 8OO A, 50 KA, TPMCCB Each 1 38599 38599

2.7 Providing and fixing following capacity four pole ON-load panel mounted changeover switches inside the existingcubical panel board including drilling holes in cubicle panel, making connections etc. as required.

2.8 Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, inter connections, powder painted including earthing etc. as required. (But without MCB/RCC Bilsolator)

217 2.8.2 2+4 way, Single door Each 133 1399 186067

218 2.8.7 12 way, Double door Each 6 2314 13884

2.9 Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. as required, (But without MCB/RCCB/lsolator)

219 2.9.3 8 way ( 4 + 24 ), Double door, horizontal type Each 7 6199 43393

2.12 Supptying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

220 2.12.1 6 A to 32'A, Single pole Each 726 237 172062

2.13 Supplying and fixing following rating, 2401475 volts, "C"curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

221 2.13.1 6 A to 32 A, double pole Each 130 667 86710

222 2.13.3 40 A to 63 A, double pole Each 20 1198 23960

223 2.13.4 40 A to 63 A, four pole Each 20 2324 46480

2.18 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

226 2.19 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. Each 35 1513 52955

227 3.2 Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required. set 25 6323 158075

228 3.4 Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required. set 6 6884 41304

229 3.6 Earthing with copper earth plate 600 mm X 600 mm X 3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required. set 6 13721 82326

230 3.7 Supplying and laying 6 SWG G.l. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with Gl thimble as required. Meter 1500 37 55500

231 3.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of brass nut bolt and & spring washer spaced at 50mm) Meter 130 1026 133380

232 3.9 Supplying and laying 25 mm X 6 mm G.t. strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with GI nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of G.l. nut bolt & spring washer spaced at 50 mm) Meter 225 133 29925

233 3.10 Providing and laying 25mm x 5mm Copper strip in 40 mm. Dia copper pipe from earth electrode including connection with brass nut, bolt, washer, excavation and refilling etc. as required. Meter 50 1628 81400

234 3.11 Providing and laying 25mm x 5mm G.I. strip in 40 mm. Dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as required. Meter 250 721 180250

235 4.1 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having singte prong on top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required. set 10 1056 10560

236 4.4 Jointing copper/ G.l. tape (with another copper/ G ltape,base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required. set 10 81 810

237 4.6 Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run) M 50 559 27950

5.7 Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

240 5.10 Supplying and fixing 70112 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,lP 65 protection and complete u.,ith integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required. Each 40 1275 51000

241 5.13 Supplying and fixing post top / gate light (width 250/300mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( Butwithout lamp) Each 15 1399 20985

5.14 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

5.15 Supplying and fixing fotrlowing types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on poleibuilding including connection earthing the body etc as required

6.1 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

244 6.1.7 20 watt LED lamp Each 15 267 4005

6.3 Supplying and fixing of following types LED electronic driver in the existing LED street Iight etc as required.

245 6.3.4 For 90 watt LED street light Each 30 2674 80220

6.4 Supplying and fixing of following types LED electronic driver in the existing LED Flood light etc as required.

246 6.4.4 For 100 watt LED Flood light Each 40 2247 89880

0.0_ Laying of one number additional PVC insulated and pVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

248 7.2.2 Above 35 sq. mm and upto 95 sq. mm Each 400 232 92800

249 7.2.4 Above 185 sq. mm and upto 400 sq. mm Each 150 274 41100

0.0_ Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

7.8 Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

255 8.9 Supply and fixing pole mounted junction box/fuse box for single phase/ 2 core low wattage street light pole with all accessories and connection etc. as required. Each 20 825 16500

256 8.15 Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required. Each 185 2482 459170

8.17 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

8.22 Supply and erection of 6 metre height Hot-dip galvanized octagonal street Iight pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

260 2301 4 Metre height Octagonal Hot-Dip galvanized street light poles with top dia. (A/F) 70 mm & bottom dia (A/F) 130 mm and made of 3 mm thick sheet, base plate diamension 220 X 220 X 12 mm including suitable size foundation bolts etc. Each 15 9500 142500

9.15 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part ll complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. ln the existing trench, complete as required.

261 9.15.5 200 mm dia (OD-200 mm & lD-175 mm nominal) metre 250 646 161500

9.16 Providing and making of following sizes octagonal street light pole foundation in reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) of specified size including PVC conduit, form work, curing, reinforcement, excavation and refilling etc. as required.

262 9. 16.1 For 4 metre pole (500mm X 500mm X 1000mm) Each 15 3305 49575

263 9.16.2 For 6/7 metre pole (500mm X 500mm X 1400mm) Each 20 4398 87960

DSR-2022 CABLE TRAY

DSR 4.1 Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

264 DSR 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness RM 200 604 120800

265 DSR 4.1.3 200 mm width X 50 mm depth X 1.6 mm thickness RM 200 689 137800

266 DSR 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness RM 150 777 116550

PART-D FIRE FIGHTING SOR ITEMS

4 Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

(b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

(d) Suitable cement concrete foundation duly plastered and with anti vibration pads

7 Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

268 7.6 80mm nominal dia Rmt 30 951 28530

269 7.7 100mm nominal dia Rmt 350 1316 460600

9 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

270 9.1 Single headed Gunmetal Set 9 7245 65205

11 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

273 13 Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. each 9 1236 11124

14 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

15 Providing, installation, testing and commissioning of stainless steel Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

16 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

276 0.0 Gunmetal Set 18 5206 93708

17 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. "Connections from riser with 25 mm dia stop gun metalvalve & M.S. Pipe and socket."

18 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

278 0.0 Gunmetal Set 9 2393 21537

19 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

279 0.0 2 way-100 mm dia M.S. Pipe Set 4 6331 25324

280 20 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Set 4 17707 70828

281 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. per liter 80000 9.7 776000

PART-E HVAC DSR-2022 ITEMS

AIR DISTRIBUTION WORK

16.12.1-DSR-2022 FACTORY FABRICATED DUCTS

Supply, fabricating, Installation, testing and commissioning of G.I Sheet metal rectangular/round ducting (supplied in L-Section for rectangular duct) complete as per class VIII conforming to IS 277-1962 (revised). The fabrication of duct shall strictly conform to ISS 655- 1963. along with supports, nuts, bolts. Support shall be considered at an interval of 3.0 mtrs and on all branches. All supports should be made of galvanised steel angle with drilled holes & GI threaded rods with check nuts & washers of Hilti with support from roof of Gripple/Equivalent make. Measurement shall be made based upon effective duct area, Contractor to bid accordingly. 2.5 mm to 3 mm thick self adhesive normal gasket for Ducting as per OEM specifications to be considered.

282 16.12.1.1-DSR-2022 Thickness 0.63 mm sheet m² 35 1080 37800

GRILLES & WIREMESH

Supply, installation, testing, balancing & commissioning of Extruded Aluminium construction Grilles. The grilles will be powder coated in shade approved by Client and installed as per approved shop drawings and specifications. The grilles may be double or single louvered, adjustable or fixed as required by Client.

283 16.15-DSR-2022 Grille with VCD m² 1 9105 9105

BILL OF QUANTITY FOR NON SOR ITEMS

Development of Tourist Facilities at Sonepur Mela Ground, Saran, Bihar

Bill of Quantity

(Each Item rate must be filled)

S.NO S.NO/SOR Description of Work Unit Qnty Amount (Rs.)

PART-A CIVIL NS ITEMS

1 Supply of GFRC Jali panels (custom design as per approved concept by Architect and Engineer in Charge) Includes mold design, casting, and curing. Technical specs • Thickness: Typically 18–24 mm • Compressive Strength: 40–80 MPa • Flexural Strength: 10–30 MPa • Dry Density: 1.8–2.1 t/m³ • Fiber Content: 2–5% by weight • Curing: 7 days under polythene or polymer curing compound • Finish Options: Sandstone, marble, antique, or custom paint Optional: antique, sandstone, marble effect. Precision cutting with diamond tools.Includes protective packaging. SS clamps, epoxy grout, or mechanical fasteners. Includes surface sealing if required. Design Approval: All jali patterns must be approved by architect/client before casting. • Tolerance: Dimensional tolerance ±2 mm. • Installation: Must comply with façade safety standards and wind load requirements. • Warranty: Minimum 5 years against structural defects and weathering. Sqm 709.5

MR-2 CNC-cut 2D metal Elephant profile artistic installations

2 Design, detailing, and fabrication of CNC-cut 2D metal Elephant combination of one Full size and one small size (custom design as per approved concept by Architect and Engineer in Charge) Must meet corrosion resistance and aesthetic standards. Finish as per artistic intent and environmental exposure. Fixed on top of gate with RCC pedestal or steel base with anchoring bolts. Artistic enhancement and nighttime visibility. Material Grade: Use corrosion-resistant metals like SS 304/316 or Corten steel depending on climate and exposure. • Finish Quality: Surface finish must be uniform, free from blemishes, and aligned with the artistic vision. • Structural Integrity: Must withstand wind loads, seismic activity (if applicable), and vandalism. • Installation Safety: All lifting and fixing must comply with local safety codes and engineering standards. • Documentation: Include soft drawings, artist’s concept approval, and structural calculations. Num 4

MR-3 Immersive Room - 1,2,3 and 4

A Projector Display

4 i 7000 Lumen, WUXGA with 4K Enhancement, 1.35-2.20 Throw Ratio, Laser Light Source, 20,000 Hrs typical life, 3 Chip LCD Projector, 400W typical power consumption Epson/Christie/Barco 16

5 ii 5000 Lumen, HD with 4K Enhancement, 0.16-0.22 Throw Ratio, Laser Light Source, 20,000 Hrs typical life, 3 Chip LCD Projector, 400W typical power consumption Epson/Christie/Barco 6

B Immersive Scenography

6 i Providing and fixing Glass Fibre fibber-reinforced polymer (Live Size Human Sculpture):- (GFRP) Sculpture (Life Size) as per architectural intent drawing & intent images. The GFRP work shall include: a) Providing sculpture drawings, based on the architectural intent drawings and intent images for sculpture and obtaining approval from the Curator & engineer in charge. b) Providing samples up to 0.04 sqm or 0.008 cum in size, wherever necessary, in approved colours, shades and finish, representing the product in actual colour, textures and patterns etc. as directed. c) Preparing necessary Molds made out of fibreglass/steels/wood/rubber etc. in accordance with approved drawings. d) Fabrication of sculptures as per approved drawing and samples by using approved mix of polyester or epoxy resin by spray process along with alkali resistant glass fibre. The glass fibre shall be laid in 3 layers on top of one another, with each layer oriented in various preferred direction and necessary quantities of mables gravel/silica sand added to obtain the required finish. All anchorage points for anchors shall be provided with concealed reinforcement, as required, each unit shall be marked with permanent serial number coordinated with sculpture drawing designators and shall be properly cured and cleaned before installation. Care shall be taken to carefully remove all toxic material harmful to plant/animal or building materials. The fabricated sculpture shall be strictly in accordance with the approved drawing and sample, in approved colours and textures. All glass fibre-reinforced plastic fabrications shall be moulded surface coat over polyester resin laminate reinforced with glass fibre structural reinforcing as required with 1. Surface coat: Ultraviolet inhibited NPG-ISO polyester gel coat 0.5mm thick, nominal. 2. Surface coat: Polyurethane, 3. Colour: as approved 4. Texture on exposed side as approved. 5. Resin: Isophthalic polyester resin with low flame spread, low smoke and low heat distortion. 6. Glass fibber: ""E"" type random chopped fibres. 7. Glass content: 15 percent by weight maximum.8. Shell thickness: 5mm minimum,9. Flexural strength:138 MPa, 10. Modulus of Elasticity: 6200MPa,11. Tensile strength: 83 MPa,12. Compressive strength:117 MPa,13. Bearing strength:62 MPa 14. Thermal expansion coefficient: 5.56x10^-6 degree C. 15. Specific gravity: 1:5,16. Variation in thickness, from nominal: Minus 1.5mm, plus 6 mm 17. Variation in thickness of gel coat: +/-0.06mm, maximum, 18. Variation from dimension indicated on drawings: +/- 3mm, maximum,19. Variation of hardware from intended location: +/- 6mm, maximum. All sculptures shall be properly installed, as directed over properly constructed substrates. All substrates must be in correct lines, levels and true Custom 16

7 ii Providing and Fixing Glass Fibre fibber-reinforced polymer (Live Size Animal Sculpture) (GFRP) Sculpture (Life Size) as per architectural intent drawing & intent images. Elephant, Horse, Cow, Bull, Camel, Goat, Hen, Dog. Custom 20

8 iii GFRP Bust with Pedestal:- Providing, supplying and installing approximately 2X 'true size' busts including GFRP mounting pedestal for each bust as per architectural intent drawings/details, as approved and directed. Sample clay models of each bust shall be submitted for approval and necessary changes/modifications carried out and fresh sample submitted, wherever required and the work executed only in accordance with the approved sample. Bust size: 900mm x 600mm Custom 14

9 iv Providing and making decorative wall painting - sq. ft. (concept paintings) at all heights and levels in accordance with approved architectural intent drawing and approved sample. The work shall include all necessary cost of labour, skilled artist/painter all material, T&P, scaffolding at all heights, leads and lifts etc. Appling necessary priming coat and approved wall putty and/or all other necessary surface preparation work as required and as directed. Item is also inclusive of providing 2m x 2m sample of the decorative wall painting in true colours and finish for approval purpose. All concept painting work must be carried out as per samples as approved by the Curator & Engineer in charge. Item is for complete fully finished works, including base preparation works and additional payment whatever shall be made on any account. Custom 1500

10 v High Relief Mural (GFRP/Cement)-sq. ft. Providing and making decorative high relief mural on wall at all height and level using white/grey cement as the base material, mixed with fine/coarse sand/aggregates as required and directed in approved colours and textures including and undercoat of 12mm thick plaster in 1:4 (1 cement & 4 fine sand). The high relief decorative mural shall involve wall art to create bamboo mats/screens and other forms in accordance with the intent architectural drawings and other details. Item is inclusive of all necessary curing, cost of all skilled artist/painter, all labour and materials, T&P, scaffolding at all heights, leads and lifts involved in execution of the complete works. Item is also inclusive of providing 1m x 1m decorative high relief mural sample in required forms, pattern, shapes and colours for approval purpose, before commencement of the specific mural work. All decorative high relief mural work must be carried out as per sample as approved by Curator & Engineer in charge. Item is for complete fully finished works, including any necessary base preparation works and no additional payment whatever shall be made on any account. Custom 500

11 vi Decorative Three Dimensional Painting -sq. ft. Providing and making decorative three dimensional wall painting at all heights and levels in accordance with approved architectural intent drawing and approved sample. The work shall include all necessary cost of labour, skilled artist/painter all material, T&P, scaffolding at all heights, leads and lifts etc. Appling necessary priming coat and approved wall putty and/or all other necessary surface preparation work as required and as directed. Item is also inclusive of providing 1m x 1m sample of the decorative three dimensional wall painting in true colours and finish for approval purpose. All three dimensional painting work must be carried out as per samples as approved by the Curator & Engineer in charge. Item is for complete fully finished works, including base preparation works and additional payment whatever shall be made on any account. Custom 1500

12 vii Canvas with frame (4x5ft) Canvas print with frame of rare old pictures of Sonpur mela UV print on canvas with highly detail with DPI 300. Canvas frame as per approved images of mela & design. Providing and making Canvas at all heights and levels in accordance with approved images and approved sample. The work shall include all necessary cost of labour, skilled artist/painter all material, T&P, scaffolding at all heights, leads and lifts etc. All canvas work must be carried out as per samples as approved by the Curator & Engineer in charge. Item is for complete fully finished works, including base preparation works and additional payment whatever shall be made on any account. Custom 4

C Content Production

13 i Cost of 4K visual production, including scripting, concept design, storyboarding, archival research, animation, and post-production of synchronized rich media content, ready for transfer to media servers. Custom 4

14 i Single emission projectors for indoor application. The warm white LED light source with Very Narrow light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 439 lm, with a 110 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium and features a white finish, processed by means of powder coating. The ingress protection degree is IP20; the total weight is of 0.2 kg. The total absorbed power is 4 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. The device features protection class II and can be ceiling-mounted. Line alight / Endo / CNC / Forma 7

15 ii Single emission projectors for indoor application. The warm white LED light source with Medium light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 1948 lm, with a 110 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium and features a white finish, processed by means of powder coating. The ingress protection degree is IP20; the total weight is of 0.3 kg. The total absorbed power is 18 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. The device features protection class II and can be ceiling-mounted. Line alight / Endo / CNC / Forma 7

16 iii Single emission projectors for indoor application. The warm white LED light source with Narrow light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 1703 lm, with a 110 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium and features a white finish, processed by means of powder coating. The ingress protection degree is IP20; the total weight is of 0.3 kg. The total absorbed power is 12 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. The device features protection class II and can be ceiling-mounted. Line alight / Endo / CNC / Forma 7

17 iv Advanced, multi-functional LED track mounted projector, tiltable vertically 0°-90° and rotatable horizontally 350°. With built-in bidirectional zooming lens with sharpness adjustability, and lens rotation. Adjustable shutters to re-frame the beam to the desired size and shape (circle, square/rectangle, or irregular four-sided shapes). High-precision optics for sharp outlines and high degree of lighting uniformity. The warm white LED light source with farmable distribution is composed of LEDs with CCT of 3000 K and a CRI 90;The ingress protection degree is IP20; The total absorbed power is 25 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. Line alight / Endo / CNC / Forma 7

18 v Single emission recessed downlights for indoor application. The Warm white LED light source with a wide flood light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 2352 lm, with a 117 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium end ab - 46100 and features a White finish, processed by means of powder coating; the diffuser is made of uv resistant polycarbonate. The ingress protection degree is IP20; the total weight is of 0.2 kg. The Non Dim power supply is to be Provided separately. Accessories like Spread Lens and Honeycomb Louvre to be provided Separately. The total absorbed power is 19.8 W. The power supply cable is included and features a 0.300 m length. The device features protection class III and can be ceiling-mounted, with a 65 mm diameter hole (in plasterboard). Line alight / Endo / CNC / Forma 7

19 vi Single emission recessed/surface upplight for indoor application. The Warm white LED light source with a wide flood light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 762 lm, with a 98 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium end ab - 46100 and features a White finish, processed by means of powder coating; the diffuser is made of uv resistant polycarbonate. The ingress protection degree is IP20; the total weight is of 0.6 kg. The Non Dim power supply is to be Provided separately. The total absorbed power is 9.4 W. The power supply cable is included and features a 0.300 m length. The device features protection class III and can be ceiling-mounted, with a 100 mm diameter hole (in plasterboard). Compliant with the EN 60598-1 standard and its specific provisions. Line alight / Endo / CNC / Forma 7

E Audio Systems

20 i Slim Column Speaker Slim Column Speaker,600MM,BLK,1PC JBL / D&B / Meyer 16

21 ii Power Subwoofer 2 x 10" High Output Compact Subwoofer; Power Rating 400W continuous at 8 Ohms; etc. JBL / D&B / Meyer 4

22 iii Digital Power Amplifier CDi Series, Network Based Digital DriveCore Multichannel Power Amplifier with 4 x 600W; built-in DSP and BLULink, etc. Crown / D&B / Meyer 4

23 iv Audio Interface Audiophile 18x20, 24-Bit/96 kHz USB Audio/MIDI Interface BSS / D&B / JBL 4

24 F Backend Infrastructure

25 i LCD Monitor ViewSonic / Dell /Samsung 1

26 ii 19'U Server Rack D-Link / Walpack / Netrack 1

27 iii Wireless Keyboard Mouse Combo Logitech / Dell 1

28 iv Playout Controller Intel Based Media System 8

29 v Playout Software for calibration, edge blending and projection mapping. Watchout / Pixera/Touch Designer 8

30 vi Cables and Networking Belden / Manhattan/Light ware 1

31 vii Projector Celling Mount Kit Custom 24

32 viii Drawings, System Integration and Onsite Programming. LOT 1

33 ix Sitework and TBL LOT 1

MR-4 INTERIOR WORK

35 1 Reception Area- Designer Wall Paneling with Italian Marble and Louvers; Fabricating and Designing of Wall panel of size 6m (W) X 8M(H) with fixing WPC Board base on vertical wall with the screw and Hitex glue for leveling the wall. Fixing of Louvers on this base and in the middle of wall design of white Italian marble to create the design as per architectural standards with fixing of polished teak wood border design on wall in required shape in between Italian marble and louvers to create an aesthetical look on wall in reception area with provision of fixing profile light. The above work will be finished as per E/I and architect design. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. Sqm 11

36 2 Providing and fixing of Experience Centre Name and Logo made of Acrylic sheet as per stander size required in architectural design given. Provision of Back lit will be provided in Name and logo as per approval of Engineer-in-charge. No. 1

37 3 Reception Counter: Providing and fixing of Reception counter of size 5400x750x750/1050mm (H) to be made of 19mm thick BWP ply of century/Green make for all surfaces with the working top of size 750mm width at 750mm level and the customer top of 300mm width at 1050mm level. There after a double layer of Flexi ply (12mm + 06mm thick) is to be fixed with necessary fittings to the block board and flexi ply is to be curved in half round shape in both side of billing counter. The front modesty panel is to be made of ply and flexi ply as required and on that a 12mm thick corian material of approved shade and make as per drawing and design. Solid surface material is to be fixed with acrylic epoxy adhesive compound including surface and edge finishing and modesty panel and mold to make the interior aesthetical look. All exposed surfaces will be finished with 1mm mica of century/Green make. Three sets of drawer chest with two drawers and one cupboard with concealed hinges and lock and key will be provided with billing counter along with key board tray on telescopic channel for smooth movement. Access flap and wire manager to be provided for electric/Data cables. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 1

38 4 Wooden Chair: Providing and fixing wooden chair made of seasoned teak wood. Back & seat cover cushion chair uphlostered in fabric. All wood shell be polished in PU Matt polish. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 54

39 5 Supplying and fixing Modular Cabin table i. MAIN TABLE SIZE - 2100MM W x 900MM D X 750MM H, ii. The worktop Will be in single piece made up of prelaminated particle board. iii. The worktop shall be made of 36mm thick prelaminated particle board with 2 mm thick hot melt PVC edge banding from REHAU iv. The worktops shall be provided with metallic inserts for precise alignments and longer life. v. The top is resting on the vertical strips of particle board. vi. The modesty of the table is also made up of 18 mm thk. prelamianted particle board which is attached table top. With the horizontal panels created under as second top under main vii. The side panels are also made up of 25mm thick prelaminated particle board with 2 mm thick hot melt PVC edge banding from REHAU vii. Complete hardwares to be used from EBCO. Table will be provided a Side unit of size 1050x450x750mm which should have two drawer on top with hinge shutter credenza under it. Made up of prelaminated particle board with 2mm thk. PVC edge bending from REHAU. Complete hardwares to be used from EBCO. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

40 6 Back Unit - Back Unit (W)2000mm X (D)500mm X (H)750mm. File Cabinets And Multipurpose Storage Units For The Contemporary Workspace. Constructed From Engineered Wood And Finished In Black Oak For A Superior Feel And Finish. The Unit Comprises Of Long Stacked Horizontal Shelves Encased In Wooden Shutters. The File Cabinet And Sideboard Is A Perfect Addition To The Wall Or On The Side Next To The Theon Office Desk For Storing Your Files, Documents And Important Papers, all complete as per direction of E/I. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 1

41 7 EXECUTIVE LEATHERETTE REVOLVING CHAIR (High Back) of approved make. The seat and back are made up of 1.2cm thick hot pressed plywood and upholstered with pure leather of required color and moulded Polyurethane foam. BACK SIZE: 520mm. (W) X 700mm. (H), SEAT SIZE: 520mm. (W) X 510mm. (D) The chair should have 360 degree Revolving type, Front pivot synchro tilt mechanism, 5-position locking with anti-shock back mechanism. The High Resilience Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS: 7888 for 25% compression. The seat and back are arrested together with a 9.0cm (W) spine made of 0.8cm thick HR steel.. It is fitted with 5nos. twin wheel castors. The pedestal is 67.0cm pitch-center dia (77.0 cm with castor). The twin wheel castors are injection moulded in Black Nylon.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

42 8 Visitor Office chair contemporary design, all black finish or as per choice of E/I, double padded cushion encased in an all black leatherette, or approved equivalent. The side padding and the headrest provide added lumbar support to the user. Material & Sub type Leatherette Colour Family Black Dimension (W)610mm X (D)505mm X (H)990mm Back Type Low Back Base Cantilever Frame Base Type Cantilever Maximum Seating Height19", all complete as per direction of E/I.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 4

43 9 3-Seater sofa of size 1920x750x740mm. The inside Frame is made of seasoned wood and has anti termite treatment. The seat and back are made of high density foam and is finished in leatherette upholstery. The frame base has webbing for supporting the cushions. The complete sofa body has polyurethane foam in desired shape.Foam of sofa will be comfortable cushion with high density and resilent foam. All upholstery materials used in specially designed and all ply wood used in MR grade. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

44 10 Wooden Centre Table: Size 1130x630x410mm (H) The Centre table is made keeping in mind the comfort with decorative glass top of toughened glass . The table is a gorgeous piece of furniture to highlight the room. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below t5he glass provide the glass with a focal point and some support. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

45 11 Wall paneling: Providing and fixing of wall panel made out of 2”x1” xCPT wood frame work at every 1.6” c/c(Vertical / Horizental) both ways, covered with 12mm thick ply all exposed surface of the paneling shell be finished with approved colour 1mm thick laminate complete as per detail drawing and instruction of E/I. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. Sqm 50

46 12 Toughened Glass : Providing and fixing of toughened glass of required shape and size. Sqm 2

47 13 Place Marker : Printed Text on sign board: Providing, fixing and installation of Signages made with premium quality vinyl sheet pasted on 05mm thick sun board. Size 150x450mm No. 1

48 1 Dining Chair: Providing and installation of café chair of the following specifications. The seat and back shall be one piece injection moulded in high impact strength poly propylene. The dimensions of seat shall be 52.5cm(W) x 53.2cm (D) and of back shall be 51.6cm (W) x 40.5cm(H).The tubular welded frame is made from dia 2.22+/- 0.03 x 0.12+/- 0.0128cm and 3.5+/- 0.03cm x 1.5+/-0.03cm x 0.12+/-0.0128cm. The tubes are buff polished to give shiny finish. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. Nos 36

49 2 VIP Stacking chair for VIP Launge : Providing and fixing chair make as approved quality of paris is a that parts fit this lounge chair it exudes style and boisterous come with its bold pattern upholstery . The supple gray fabric complements the solid legs up on which tghe chair is set for a firm sturdy base bring home some chic style with paris out. Newest lounge chair for the long time sitting. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 10

50 3 Dining table: Providing and fixing of dining table in round shape The top of the table will be 30 mm thick including 18mm ply and 12mm White granite top table. Unrestructured of the table will polished seasoned wood of specially designed. The table top will be pasted with chemical adhesive finished with corners edging incuding rubbing, curing, moulding and polishing to the edges to give high gloss finish complete at all levelsMake VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 6

51 4 Cash Counter: Providing and fixing Cash counter of size 4500x750x750 (H) to be made of 19mm thick BWP ply of century/Green make for all surfaces with the working top of size 750mm width at 750mm level. All exposed surfaces will be finished with 1mm mica of century/Green make. Two sets of drawer chest with two drawers and one cupboard with concealed hinges and lock and key will be provided with billing counter along with key board tray on telescopic channel for smooth movement. Access flap and wire manager to be provided for electric/Data cables.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 1

52 5 Providing and fixing MEDIUM BACK EXECUTIVE REVOLVING CHAIR with adjustable lumber support in mesh back with armrest with PU pad. The back of the chair will be provided adjustable support on head and neck for extra comfort. The seat is made up of 1.2cmm thick hot pressed plywood, upholesterse with fabric and moulded polyurethane foam. and center tilt synchro Mechanism, Peneumatic Height Adjustment. The pedestal is with twin wheel injection moulded casters.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

53 6 Kitchen Island Unit with Two Burner Range : Kitchen Island Unit made of Stainless Steel Sheet and SS Square Frame with Two Burner Range of total size 12’W x 2.5’D with height 32” and 28” will be in two parts fitted with drawer for keeping spices and salt below cook top. A sliding shelf will be provided under the cook top & drawer for the store of waste cooking materials, additional shelf will be given in bottom for keeping cooked food. In another part a ss sink with swan head tap will be fitted. And also making arrangement for keeping LPG cylinder inside a covered cupboard along with three drawer unit for keeping kitchen items. The material used in fabricating the above items is such as Top Sheet 18 guage, Shelf & facia will be in 22 guage in 304 Grade, Legs & Frame -- square pipe in Grade 202, as per drawing. No. 1

54 7 Kitchen Hood: Fabricating of Kitchen Steel Hood of Size 72”x36”x20” with filter along with ducting pipe in GI sheet and exhaust fan for out-let to remove particles such as dust, dirt, smoke etc. The out-let pipe will be hanged with fast nut in the ceiling No. 2

MR-5 Sculpture In Central Courtyard

55 Design, detailing, and fabrication of metal sculpture (custom design as per approved concept by Architect and Engineer in Charge) Must meet corrosion resistance and aesthetic standards. Finish as per artistic intent and environmental exposure. RCC pedestal or steel base with anchoring bolts. Artistic enhancement and nighttime visibility. Material Grade: Use corrosion-resistant metals like SS 304/316 or Corten steel depending on climate and exposure. • Finish Quality: Surface finish must be uniform, free from blemishes, and aligned with the artistic vision. • Structural Integrity: Must withstand wind loads, seismic activity (if applicable), and vandalism. • Installation Safety: All lifting and fixing must comply with local safety codes and engineering standards. • Documentation: Include soft drawings, artist’s concept approval, and structural calculations. Num 11

MR-6 Mural- On Toilet Block Building

57 Providing and installing a high-relief mural designed in an abstract realism style, approximately measuring 16 meters by 5 meters. The artwork is crafted from durable sand and cement, with a surface layering thickness ranging from approximately 2 inches to 6 inches as needed. It comes with a 12-month material warranty from our side. The surface will feature a clear Western color, complemented by a two-tone color palette. To enhance the richness and depth of the colors, a matte nish pigment will be applied, ensuring vibrant, long-lasting hues that add a distinctive character to the mural. Sqm 80

MR-7 Super Tree

59 Design, detailing, and fabrication of metal super tree (custom design as per approved concept by Architect and Engineer in Charge).Must meet corrosion resistance and aesthetic standards. Finish as per artistic intent and environmental exposure. RCC pedestal or steel base with anchoring bolts. Artistic enhancement and night time visibility. General Description: 1- Structure Type: Decorative metal super tree, inspired by vertical garden or sculptural installations. 2- Purpose: Aesthetic landmark with integrated lighting for public spaces, parks, or commercial zones. 3- Height Range: Typically 6–15 meters, depending on design intent. 4- Finish: Powder-coated or weather-resistant paint in specified color Num 8

Main Frame: 1- Mild steel or galvanized steel sections (IS 2062 grade or equivalent). 2- Hollow circular/square pipes for trunk and branches. 3- MS plate (minimum 20 mm thick) with anchor bolts for foundation. Lighting Fixtures: 1- LED spotlights, strip light, RGB floodlights, Pixel dot light on metal structure as per architectural design and concept. 2- IP65 or higher rating for outdoor use. 3- Smart control options (DMX, remote, or app-based).

Fabrication & Installation 1- Welding: MIG/TIG welding with proper finishing and grinding. 2- Surface Treatment: 3- Sandblasting before painting. 4- Zinc primer + top coat (minimum 100 microns total). Foundation: 1- RCC pedestal with anchor bolts. 2- M25 grade concrete with steel reinforcement. Electrical Works 1- Cabling: 2- Armoured copper cables (1.5–4 sq mm depending on load). 3- Concealed conduits within the structure. 4- Control Panel: 5- Weatherproof enclosure. 6- Timer or sensor-based automation. 7- Earthing: 8- GI earth rod with proper connections.

Lighting Design 1- Type: Ambient + accent lighting. 2- Color Options: Static white or programmable RGB. 3- Mounting: Recessed or surface-mounted depending on fixture type. 4- Power Load: Estimated 500W–1500W per tree depending on size and lighting density.

60 Supplying, Providing, and Fixing, a musical fountain—also known as a dancing fountain or fairy fountain—is a choreographed water feature that synchronizes water movements, lighting effects, and music to produce captivating shows. These fountains are often installed in public parks, malls, resorts, and cultural venues. as per Architects and Engineer in Charge. How It Works 1- Water Jets: Controlled by high-pressure pumps and valves to shoot water in patterns. 2- Lighting: LED or RGB lights illuminate the water, often changing color and intensity. 3- Music Synchronization: A computerized control system times water and light effects to match the rhythm and mood of the music. 4- Automation: Some advanced systems can respond to live music in real-time, creating spontaneous displays. Num 1

MR-9 Illuminated 3D text on external façade

61 YOU ARE AT SONPUR MELA (900MM HIGH) Providing,fixing & installation of Illuminated 3D text on external façade having 3mm white transparent Acrylic Letters on sides & black acrylic on front With LED 170 per Running Inch Each Alphabet 18

PART-B PLUMBING NS ITEMS

63 NS-1 Providing Supply of Grape Supporting Bars, 12 mm diameter, 2.4 m long, fabricated from mild steel with U-bend at ends for wire holding, surface painted (2 coats red oxide + 1 coat enamel), suitable for trellis grape farming system. Nos 10

64 NS-2 Providing Tixing Testing Commissioning Delta Brass Robe Hook | Coat Hook | Bathroom Accessories (Chrome Finish, Wall Mounted) testing of joints complete as per direction of Engineer in Charge. Nos 21

65 NS-3 Providing Supply and place PARASNATH brand stainless steel perforated dustbin, capacity 10–15 liters, made from high-grade SS 202/304 stainless steel with a matt finish. Dustbin shall have a perforated body design for ventilation, be corrosion-resistant, durable, and suitable for indoor use in offices, institutions, or commercial spaces. Approximate dimensions: 250mm diameter x 300mm height. Smooth edges and anti-skid base. Sample to be approved prior to supply. Nos 25

66 NS-4 Providing & fixing of approved coloured verticle type hot water 25 ltr geysers. The inner container shall be made of copper sleeve with PUF insulation between inner and outer container, element pipe and heating element, pressure cum vaccume release, thermostat and thermal cutout arrangements and fusible plug. The outer container shall be of powder coated finish with all other accessories including fixing brackets complete as required. Nos 4

67 NS-5 Supplying and fixing of shower diverter made of brass/chrome-plated, suitable for concealed installation, 2-way/3-way function, including necessary fittings, cutting, threading, and making connections complete in all respects as per direction of Engineer-in-Charge. Nos 10

68 NS-6 Supply Installation, commissioning and testing of single phase 2H.P. submersible pump set having discharging capacity 3 Ips at a total head of 30 meter (approx) of KSBj Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & (i) 50 mm dia x 3 mtrs long medium classG.I column pipe both end thread and one end socketed- 6 (six) nos (ii) lx3x2,5 mm' flat copper conductor submersible cable -40 (forty) mtrs. (iii) 50 mm dia union socketlIonel no. (iv) 65 mm dia x 250 mm long G.!. nipple- 1(one) no. (v) 50 mm dia G.I Elbow-l(One) no. (vi) 50 mm dia M.S, clamps-2(Two) Pairs. (vii) 50 mmx 250 mm long G.I nipple- lIOnel no. (viii) Tube well cap for T/WelllIonel no. (ix) 50 ":l~ia x 65 mm dia 2 No

Supply Installation, commissioning and testing of floor mounted outdoor type loT feeder pillar single phase starter controll pannel operated on 220V, 3 phase, 50 cis for 3 HP Submersible pump set made of MS sheet (minimum 2 mm thick) duly spray power coated painting with following accessories made of M.Ssheet ( minimum 2mm thick) duly spray powder coated painting with following accessories (i) 90-220 V range single phase7. 5 KVA automatic voltage stabilizer make- Sen & Pandit/ Vertex/ISI marked If any. 1No. (ii) Suitable single phase starter control panelfor above motor of BCH /L&T make-1 (one) no. 2 No

Supplying & fitting 2.5 mm' copper service cable from power point from nearest source up-to I pumping station 150 m

Providing all materials and labour required lor doing earthing station with G.I earth pipe of 40 mm dia x 4.5 mtrs 20fts. long G.I pipe including accessories excavation of earth , providing masonry enclosure with Coverplate having locking arrangementand watering pipe etc.with salt, charcoal,etc.as per IE & IS specification 2 No

PART-C ELECTRICAL NS ITEMS

NS-1 NS ITEMS LIGHTING

69 SITC of Step light with 3W,h aving IP65 Protection Rating, CCT: 3000K / 5600K, Aluminum Alloy Material, Body Color: Telegrey. Input Voltage: AC100-230V Each 140

70 NS-2 SITC of 9W Mono color Spike light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Spike for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV- 4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Each 115

71 NS-3 SITC of 9W Mono color Spot light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Each 130

72 NS-4 SITC of high quality inground light with a power rating of 12W and CCT —3000K - 5600K for crisp articulation—offering versatility across architectural applications. Beam Angle : 30°, designed to minimize hot spots and ensure smooth light distribution. The fixture’s body combines stainless steel and aluminium, achieving a balance of corrosion resistance and thermal efficiency. Rated IP67, it guarantees complete protection against dust ingress, making it ideal for high-exposure environments including driveways, plazas. The unit supports wide-range Each 70

73 NS-5 SITC of 10W COB Downlight - Metal Body, CCT: 3000K, Power Input: AC 140-240V, 50Hz, IP Rating: IP65. Each 140

74 NS-6 SITC of high quality long through mono color Linear wash light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 36W, CCT : 1800K/3000K/4000K/6000K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK07, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP67 connector having the length >300mm. Each 22

75 NS-7 SITC of 9W Mono color Spike light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Spike for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV- 4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Each 40

76 NS-7.1 SITC of UNILinear Flex is IP68 cove lighting with reliable performance and excellently water-proof, anti-dust LED strips, CCT : 1100LM 3000K L5000, (as per the design approval) with professional design for vivid colors. or equivalent with the engineer or 3rd party testing laboratory approval. MTR 50

NS-8 NS ITEMS DG SETS

Designing, Supply & erection of DG set of capacity given below with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 +(-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel, making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer, outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge.

The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 v. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator,control fuse, frequency meter, CT's) h) Metering set 60/5A/11 OV (Amp. Meter, Volt Meter) i) Overload protection for DC-1 No. j) Battery Charger 24V DC k)Copper bus bar of suitable size I) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, De control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge

77 200KVA DG SET Each 1

NS-9 ELECTRICAL PANEL

Design, manufacture supply, installation, testing and commissioning of the following extensible cubicle type indoor mounting, dead front, fully compartmentalised with hinged lockable detachable front & back openable, dust and vermin proof, floor mounting sheet steel clad switchboard fabricated out of 2 mm thick CRCA powder coated sheet steel suitable for use at 415 volts 3 phase 4 wire 50 cycle system and to withstand a symmetrical fault level as specified at 415 volts. Panels shall be fabricated in easily transportable sections, length, height, depth etc. to match with site condition. All incomer breaker and Bus Couplers shall be interlocked electrically as shown in SLD and specifications.

Note: The following provisions shall be required to be made in the switchboard as detailed below:

a) The Switchboards shall have provision to accommodate all cables from the bottom /top as required.

b) All live accessible parts shall be shrouded with 1mm thick polycarbonate/3 mm thick FRP sheet and all equipment shall be finger touch proof. The busbar insulation shall be with heat shrinkable sleeves according to the colour code. SMC shrouds and busbar supports shall be used.

c) Galvanised hardware with zinc passivation shall be used in fabrication of Switchboards.

d) All rear door of Main LT Panel shall be Almirah type with lockable arrangement.

e) Space heater shall be provided with thermostat with 6A MCB as backup protection in each section of Main LT Panel & controlled with 20 A DP MCB, 10 KA.

f) Provision of one 6/16 amp socket & compartment lighting for each vertical section of main LT Panel.

g) The panel shall display Main Incomers Bus Couplers of Main LT Panel. This line diagram shall be made from luminous non fading materials to glow in dark and each breaker legend shall be provided with bi-colour LED lights to show the Phase indication Lamp & ON/OFF status of the respective feeder (Incomers / Bus couplers)

h) All control & power wiring shall be broughtout upto the cable alley in the terminal blocks. 10% extra terminals shall be supplied along with Panel.

i) An approval shall be taken for each panel before manufacturing.

j) Suitable Aluminium earth bus to be provided throughout the length of Switchboards.

k) All indication lamps / illuminated push buttons shall be LED type.

l) 2A SP MCBs shall be used as backup protections.

m) Coil of all motor starters shall be fed from 440 V / 230 V Control Transformer.

n) All incomer meters of Main LT Panel shall be multifunction & should have all the electrical parameters like, Voltage, Ampere, KW, KVAR, KWH, PF, Frequency etc. with communication port RS-485.

o) All feeders with KWHr meter will be Electronic Dual Reading KWHr meter alongwith appropriate CT's and 1 sq. mm control wiring from each KWHr meter for RS-485 communication till DCU's compartment.

p) Provision for providing 230V AC supply for Dual KWHr metering when any or all DG are in operation

q) One separate compartment of minimum size 400 x 900 mm for power management system of D.C.U.'s with control wiring as per following specification and control wiring scheme. Control wiring shall be looped from each energy meter till DCU's compartment for sending DCU register change command from data connectivity.

r) All CT & PT's shall be cast resin type. Class - 3 CT shall be provided up to 100 amp and above that the CT shall be Class - 1.

s) Zone selective Interlocking to be hardwired between incoming & outgoing ACB of main LT Panel.

t) All incomer ACBs of Main LT Panel shall be with microprocessor based releases (O/C, S/C & E/F), display of current/voltage and communication port RS-485, however ACB Incomers in other distribution panel and outgoing of Main LT Panel shall be with standard releases.( Ics=100%Icu=Icw )

u) All Main LT Panel outgoing ACB shall be with inbuilt earth fault release with CT & MCCB shall be with earth fault module with associated neutral CT for feeder protection, for TP feeders & E/F release for FP feeders.

v) All MCCB shall be provided with Rotary handle, door interlocked & lockable in off position of MCCB.

w) All Main LT Panel outgoing MCCBs shall be with microprocessor based releases, line load reversibility, Ics = 100% Icu.

x) Rating of Neutral bus-bar shall be 50% of phase-bus bar

y) All MCB to be C Curve type

z) Micro PLC for auto load management & interlocking as per logic specified.

i) 800amps 50 kA 440 volt FP MCCB with overcurrent and short circuit and earth fault module, with heavy duty solid detachable neutral link

Metering for incoming:

a) 3 nos 800/5A Class 1, 15 VA Burden CT's for metering & 1 nos associated Neutral CT for earth fault module.

b) Digital flush type class -1.0 accuracy multifunction meter with RS-485 communication port for measurement of THD, KVARH KW, KWH, KVAR, PF, V, A, Hz, equivalent to EM6400 NG, with 3 Nos. current transformers of required ratio, 15 VA Class 1.0

c) Phase indication Lamp & ON/OFF indicating lamps with 3X2A SP MCB as backup protection.

TPN Aluminium busbars aluminium three phase and neutral busbars rated at 1000 amps, 50 KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Current density of Bus Bar to be 1.0 sq.mm / amp.

A 10 Nos. 100 Amp 4P MCCB With breaking capacity of 25KA

B 2 Nos. 63 Amp 4P MCCB With breaking capacity of 25KA

C 6 Nos. 63 Amp 4P MCB With breaking capacity of 10KA

C 1 Nos. 63 Amp DP MCB With breaking capacity of 10KA

78 MAIN LT PANEL complete as above required. Each 1

NS-10 METER BOARD PANEL (BLOCK AREA AREA)

i) 100 amps 25 kA 440 volt FP MCCB with overcurrent and short circuit and earth fault module, with heavy duty solid detachable neutral link

Metering for incoming:

a) 3 nos 100/5A Class 1, 15 VA Burden CT's for metering & 1 nos associated Neutral CT for earth fault module.

b) Digital flush type class -1.0 accuracy multifunction meter with RS-485 communication port for measurement of THD, KVARH KW, KWH, KVAR, PF, V, A, Hz, equivalent to EM6400 NG, with 3 Nos. current transformers of required ratio, 15 VA Class 1.0

c) Phase indication Lamp & ON/OFF indicating lamps with 3X2A SP MCB as backup protection.

TPN Aluminium busbars aluminium three phase and neutral busbars rated at 150 amps, 25KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Current density of Bus Bar to be 1.0 sq.mm / amp.

A 20 Nos. 32 Amp DP MCB With breaking capacity of 10KA

B 4 Nos. 63 Amp 4P MCB With breaking capacity of 10KA

79 SUB LT PANEL complete as above required. Each 8

NS-11 Feeder Pillar

Design, fabrication, assembling, wiring and supply, installation, testing and commissioning of Distribution Panels fabricated out of (load bearing member of 2mm and non load bearing member 1.6 mm thick) GI sheet steel in cubicle compartmentised modular 3b construction, free standing floor mounted with bottom cable entry,300 mm MS painted stand and standing covering from 3 sides, IP 55 double door with canopy ,dust and vermin proof with reinforcement of suitable size angle iron, channel, `T’ sections and / or flats wherever necessary. 3 mm thick cable gland plates shall be provided at the bottom of the panels with appropriate stand etc. Panels shall be treated with all anticorrosive process before powder coating as per specifications and final approved shade. 2 Nos. earthing terminals shall be provided for all distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be used in fabrication of panels.(Make AAA Switchgear, Indiatech panel, Neptune india)

Feeder Pillar (For External Landscape lighting) IP 55 for outdoor Protection

63 Amps 4 pole MCCB

100 Amps TPN Aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set

63 Amps two pole MCB incomer with 63 Amps DP contactor 0-24 hours timer auto / manual and outgoings including 6 No. 10/16/20 Amps SP MCB with separate neutral link of each phase- 1 set (50%)

40 Amps DP MCB with 32 amp industrial sockets - 2 sets

63 Amps 4 Pole MCB - 2 set

80 Feeder Pillar for external / landscape lighting as described above Each 1

NS -12 NS ITEMS C.C.T.V.SYSTEM

(Make- Honeywell, Godrej, Samsung as per approval of EIC)

81 A IP Varifocal Dome camera: Design, Supply, installation, testing and commissioning of 4MP BULLET IP CAMERA.,minimum 1 year warranty Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 45

82 B Supply , Installation , Testing and commissioning of 16 Channel NVR (Network Vedio Recorder) Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 3

83 C Supply, installation, testing & commissioning of 43" inches LED screen suitable for showing out puts from NVRs on a single screen (24x7) complete in all respect complete as required. Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 2

84 D Supply, laying and termination of CAT6 cable in existing conduits/ raceway/ cable tray for both video and control. MTR 2000

85 E Supply, installation, testing & commissioning of 4 TB Survillance HDD for camera recording.(24*7 ) Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 3

86 F Supply, installation, testing & commissioning of 8 PORT POE GIGA SWITCH Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 6

87 G Supply, installation, testing & commissioning of RJ 45 CONNECTOR Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 50

NS-13 11kV / 415V PACKAGED SUBSTATION: HT SIDE: 4P VCB TRANSFORMER: OIL TYPE LT SIDE: 4P MCCB

Outdoor type Package Substation with facility for internal lighting, earthing, padlocks etc. Connection between RMU & Transformer will be by 3 nos. 1C x 95 Sqmm. Aluminium conductor XLPE cable and connections from Transformer to LT ACB / MCCB will be by Aluminium bus bar connections. Cable termination kits for RMU shall be in the scope of supply (within the enclosure).

Package Substation will have the following equipments:

1 No. 630A ACB as Outgoing to Transformer : 1 No.

IDMT RELAY– Self Powered, Microprocessor based numerical 3 Nos. O/C +1 No. E/F (with inbuilt tripping mechanism - mytop or equivalent) with LCD display - ON/OFF/Trip..

Dual core CT’s for protection & metering, cast resin type and of suitable ratio & burden, (Class-1 for metering & class 5P10 for protection).

Cast Resin PT's of 11000V/√3/110V/√3 ratio of Class-1 accuracy & of suitable burden with HV fuse on primary side & MCB / MPCB on secondary side.

The Ring Switches and Tee-Off Circuit Breaker are provided with Integrated Earthing Switches with Making Capacity.

Live cable indicator for ring switches.

Shunt trip coil rated for 24V DC

SF6 Gas pressure indicator.

Padlocking facility.

Mechanical indications for breaker ON / OFF / TRIP

Communicable type multifunction meter with MDI (A, V, Hz, KW, KWH, KVA, KVAH, KVAR, KVARH)

Ammeter with selector switch.

Voltmeter with selector switch.

Line Voltage presence indicator.

Transformer Auxiliary Relay with alarm & trip contacts for:

Winding temperature

Oil Temperature

Emergency 'OFF' Push buttons

Manual ON/OFF Push buttons

12 Windows annunciator. (Hooter @ Remote location i.e. inside LT Panel room) with necessary cabling.

Trip circuit healthy indication

230V AC / 24V DC Power Pack of suitable capacity

CFL based bulk head light fixture with limit switch in the HT Compartment.

11KV/415V, 400.kVA three phase, Dyn11, tapping + 15% to - 15% in steps of 2.5% On load Tap changer (OLTC), CU/CU Winding Hermetically Sealed without gas cushion ONAN Transformer with standard accessories :1 No.

Transformers shall be as per IS : 1180 ,Level 2 ( Star 1 rated)

Door interlock to trip HT breaker on opening of transformer compartment door (only in transformer's with off circuit tap changer).

1 No. 4pole 800A / 50kA manually operated fixed type *MCCB with microprocessor based O/L, S/C & E/F releases. Ics = Icu for the breaker.

LT side metering shall include: 1set of LT cast resin CT's, PT’s & Communicable type VAF meter, LED TYPE R Y B indication lamps, ON/OFF/ Trip indication lamps, control MCB's / MPCB’s of required fault withstand and control wiring etc. at the LT side incomer breaker.

CFL based bulk head light fixture with limit switch in the LT Compartment.

88 Packaged Substation as described above. No 1

SOLAR PV SYSTEM

NS-14 Supply Installation testing commissioning of Solar Photovoltaic grid connected roof top Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- (a) Solar Photovoltaic Module manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. (b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz plus /- 2.5 Hz, output voltage suitable to generate AC (c) Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degrees C. The PCU shall adjust the voltage and frequency level to suit grid frequency (d) Data Monitoring System complete with accessories. (e) Fixing of Array junction box and Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. (f) Lightning and surge voltage protection. (g) Connections and Interconnections by supplying and fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power

89 1 Above 100 kWp and up to 500 Kwp KWp 200

PART-D FIRE FIGHTING NS ITEMS

FIRE EXTINGUISHERS

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity.

90 NS-1 ABC powder type fire extinguisher of 6 Kgs. Capacity, with initial filling (Mono Ammonium Phospate Powder) in brand new cylinder with powder coated finish, Stored Pressur type, Pressure Gauge, Controllable discharge mechanism with Hose & Nozzle , confirming to IS:15683:2008. Nos. 15

91 NS-2 Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, Co2 gas as per IS 15222 with controll discharge mechanism fitted with Hose & Horn applicable on Class B fire rating 21B confirming to IS: 15683:2008. CO2 Cylinder as per IS 7285 with ISI mark. Nos. 15

PART-E HVAC NS ITEMS

AIR CONDITIONING WORK

VARIABLE REFRIGERANT VOLUME/ FLOW SYSTEM

Supply, testing and commisioning of Aircooled inverter based modular type VRF/ VRV system using R-410A refrigerant. This should complete with interconnecting copper refrigerant piping with insulation, copper power cabling and control wiring in PVC conduit between indoor and outdoor (given in separate head). Power supply to suggested ODU shall be given at one point and further distribution shall be in scope of contractor including panel and cabling. This specifications is applied for all items wherever it is required.

MK-1 OUTDOOR UNITS

Supply, unloading, storing, shifting, installing, testing and commissioning of Modulating VRF/VRV Outdoor Unit (Cooling Only Type) suitable for 415V/ 3Ph/ 50Hz AC. Supply including 100% Inverter Based Scroll Compressors with first charge of R-410A refrigerant with DC Inverter, High efficiency heat transfer cooling coil suitable for environment friendly R-410A refrigerant, Air cooled propeller type condensor fan with DC motor drive, interconnecting piping, suction line insulation, microprocessor control panel suitable for automatic operation, High speed calculation inverter control, MS frame with rubber pad etc. all complete as per specifications, drawings and direction of Engineer In charge.

The unit capacities shall be considered after taking deration into account due to copper piping lengths & ambient conditions. The Unit shall be capable of operating upto 52 °C ambient temperature. Test certificates to this effect must be provided prior to supplying equipment at site. The card replacement shall be done without any extra cost if it fails to perform under indicated voltage range and fluctuations.

VRV ODU's shall be capable of operating in the following range: i) For Cooling : (-)5 °C to 52 °C

Note- Nominal capacity suitable for cooling requirements. Combination above capacities as per OEM for economical & efficient combination.

MK-2 4 WAY CASSETTE UNIT

Supply, unloading, storing, shifting, installing, testing and commissioning of VRV/VRF type 4-way cassette Indoor units. The unit shall include pre-filter, fan section and DX-coil section. The housing of the unit shall be powder coated galvanized steel. The body shall be light in weight. Unit shall have an external attractive panel for supply and return air. The condensate drain of the units to be done with proper insulation & fittings to be terminated to the main drain line as per the layout plan. All indoor AC units shall be provided with drain pumps which shall be subjected to brand selected.

93 2.0 TR Nos 1

94 2.6 TR Nos 4

95 3.2 TR Nos 2

96 4.0 TR Nos 2

MK-3 HI WALL UNIT

Supply, unloading, storing, shifting, installing, testing and commissioning of VRV/VRF type wall mountedhi-wall units. The unit shall include pre-filter, fan section and DX-coil section. The housing of the unit shall be powder coated galvanized steel. The body shall be light in weight. Unit shall have an external attractive panel. The condensate drain of the units to be done with proper insulation & fittings to be terminated to the main drain line as per the layout plan.

97 1.5 TR Nos 2

MK-4 INLINE FAN

Supply, unloading, storing, shifting, installing, testing and commissioning of circular Inline fan shall be complete with non-stalling backward curved centrifugal Impeller, GSS Casing, direct driven Single phase(230 V±10%, 50 Hz.) external rotor Motor with IP44 Protection & Class B Insulation with speed regulator & all accessories as required. Noise Level shall not exceed 60 dB (A) at 3 meters at room condition.

98 Capacity: 400 CFM External Static Pressure: 12 mm WC Nos 1

MK-5 COPPER REFRIGERANT PIPING

Supply, installation, testing and commissioning of refrigerant pipe work with (19mm/13mm thick) closed cell elastomeric nitrile rubber/XLPE tubular insulation between each set of indoor & outdoor units as per specification, all piping inside the room shall be properly supported with GI slotted cable trays & all external piping shall run in covered cable tray. UV coat protection to be applied on the exposed elastomeric insulation provided on pipes. (Cost to be included in quoted price)

99 41.8 mm O.D. (with 19mm insulation) RM 25

10 34.9 mm O.D. (with 19mm insulation) RM 6

101 28.6 mm O.D. (with 19mm insulation) RM 10

102 22.2 mm O.D. (with 19mm insulation) RM 6

103 19.1 mm O.D. (with 19mm insulation) RM 55

104 15.9 mm O.D. (with 19mm insulation) RM 35

105 12.7 mm O.D. (with 13mm insulation) RM 10

106 9.5 mm O.D. (with 13mm insulation) RM 65

107 Y Joints Pair 11

MK-6 UPVC CONDENSATE DRAIN PIPING

Supply, installation, testing and commissioning of 6 Kg/m3 density UPVC pipe (heavy duty) with 9mm thick nitrile rubber insulation (tube insulation) with protective coating as per the approved shop drawings and specifications.

108 40mm dia. RM 15

109 32mm dia. RM 30

110 25mm dia. RM 20

MK-7 CONTROL & TRANSMISSION WIRING

Supply, installation, testing & commissioning of copper flexible control cum transmission wiring of 2core x 1.5mm2 in suitable conduits between indoor and outdoor units. Charges of conduits are included.

111 2 Core x 1.5 sqmm copper RM 120

BIHAR STATE TOURISM DEVELOPMENT CORPORATION LTD.

(A GOVERNMENT OF BIHAR UNDERTAKING)

DEVELOPMENT OF TOURIST FACILITIES AT SONEPUR MELA GROUND, SARAN IN BIHAR

QUOTING SHEET FOR BIDDERS

Name of Contractor

Address of Contractor

E-mail ID of Contractor Mobile Number

NIT -08/E-TENDER/ BSTDC/SBD/2026-27

Sl No. Description Estimated Amount Rate Quoted by Contractor

% Above/Below TOTAL QUOTED AMOUNT Rs.(In Figure) TOTAL QUOTED AMOUNT Rs.(In Words)

1 Total Schedule Amount (Rs.) 138508169

2 Total Non-Schedule Amount (Rs.) To be Quoted !

TOTAL AMOUNT Rs. 231072558

Development of Tourist Facilities at Sonepur Mela Ground, Saran, Bihar

Bill of Quantity

S. No Sl. No./ Code. SOR- Description of Work Unit Qnty Rate (Rs) Amount (Rs.)

PART-A CIVIL SOR ITEMS

2.29 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cmdeep and disposal or rubbish ,lead up to 50 m lift up to 1.5 m

0.0 Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

2 2.6.1 All kinds of soil Cum 3698.02 314.9 1164506.498

3 2.28 Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. Cum 5973.32 287.3 1716134.836

0.9 Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap.)

0.0 Concrete Work

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

5 4.1.6 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size) Cum 656.54 3279.8 2153319.892

6.1C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

6 6.1.14C Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work Cum 1670.7125 4923 8224917.6375

7 6.45.2 Cement mortar 1.:4 (1 cement: 4 coarse sand ) Sqm 81.7 700.8 57255.36

0.0 Reinforced Cement Concrete Works

0.0 Centring and shuttering including strutting, propping etc. and removal of form for:

8 5.9.1 Foundations, footings, bases of columns, etc., for mass concrete. Sqm 1720.04 211.6 363960.464

9 5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 3803 437.5 1663812.5

10 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 2086.82 404.7 844536.054

11 5.9.6 Columns, Pillars, Piers, Abutments, Post and struts Sqm 2541.02 494.4 1256280.288

5.22 Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars

5.33 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and including retard setting of concrete, improve work ability without impairing strength and admixtures in recommended proportions as per IS: 9103 to accelerate, reinforcement, durability as per direction of Engineer-in charge.

16 5.33.1 All work upto plinth level Cum 1210.1 5063.4 6127220.339999999

17 5.33.2 All work from plinth level upto floor V level. Cum 1355.44 5863.2 7947215.808

0.0 Flooring Works

18 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I. Sqm 12684.75 283.3 3593589.6750000003

11.78 Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc.complete as per manufacturer’s specifications & direction of Engineer-in-Charge. 60mm thick C.C.paver block of M-35 grade with approved colour, design & pattern.

16.69 Providing and laying at or near ground level Factory made kerb stone of M-25 gade cement concrete in position to the required line levl and curvature jointed with cement mortar 1:3(1 cement:3 coarse sand) including making joints with or without grooves (thickness of joint except at sharp curve shall not to more than 5 mm)including making drainage opening wherever required completred etc.as per direction of engineer in charge (length of finish kerb edging shall be measured for payment)(Precast C.C kerb stone shall be approved by Engineer in charge)

20 For Green Area A Cum 3.375 7998.8 26995.95

4.9 Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S.Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S.Pipes 40 mm dia and 450 mm long with 150x150x6mm M.S.plate welded at bottom and embedded 150 mm in cement concrete 1:3:6 (1Cement :3coarse sand (zone-III) derived from natural sources : 6graded stone aggregate 20 mm nominal size derived from natural sources), including necessary excavation of size 250x250x450 mm deep for the same in bitumen / concrete pavement at specified spacing

21 In Parking Nos 250 588.6 147150

11.3 40 mm thick fine dressed stone flooring over 20 mm (average) thick base with joint finished fiush:base 1:5 (1 cement: 5 coarse sand )with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.

7.37 Stone work ( machine cut edges veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately

23 7.37.1.A Dressing of sand stone in veneer work Sqm 1375.2 2563.8 3525737.7600000002

8.12 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (avearage) thick base of cement mortar 1:4 (1cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

24 (a) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Sqm 1279.17 2147.7 2747273.409

11.41A Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the anufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.1 Double charge vitrified tile polished finish of size

11.41A Providing and laying Vitrified tiles in floor in different sizes {thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.1 Double charge vitrified tile polished finish of size

27 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (Thickness to be specified by the manufacture) of approved make inall colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement Motar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete Sqm 141.7 795 112651.49999999999

8.13 Providing and laying Polished Granite Store Flooring In required design and patterns , linear as well as curvilinear portion of the thick stone slab over 20mm (average)thick base of cement mortary 1:4(cement :4 coarse sand)laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing curing and polishing etc.all complete as specified an as directed by the Engineer in Charge

28 8.13.1 Polished Granite Stone slab jet black Cheary Red ,Elite Brown Cat Eye or equivalent. Sqm 279 3605.2 1005850.7999999999

0.0 Aluminium Work

0.0 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up tandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, traight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

29 21.1.2.3 Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) KG 577.9575 480 277419.6

30 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture ,including providing and fixing top & bottom pivot &spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete asper direction of Engineer-in- charge (Door handle,lock and stopper etc.to be paid separately). Sqm 8.16 5143 41966.88

31 10.18 Providing and fixing circular/ hexagonal cast iron or M.S sheet box for ceiling fan clamp 140mm internal dia, 73mm height, 5mm thick rim bottom and top lids,1.5mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3mm dia round headed screws, one lock at the corners.Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. Num 311 165.4 51439.4

10.32 Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

32 10.32.2 In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works. KG 6494.4 114.6 744258.2399999999

10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel rimer, including welding and bolted with special shaped washers etc. complete

33 10.16.1 Hot finished welded type tubes KG 2776.33 123.9 343987.287

0.9 Supplying and fixing Rolling sutters of approved make.made of required size of M.S. laths inter locked together through their intire length and jointed together at the end by locks mounted on specially designed pipe shaft with brackets, side guides and arragments for inside and out side locking with push and pull operation complete including the cost of providing and fixing necessery 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

34 10.6.1 80x1.25mm M.S laths With 1.25mm thik top cover. Sqm 1134 2673.7 3031975.8

35 7.42 Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge Each 750 265 198750

36 9.145 Providing and Fixing factory made PVC door frame made of PVC extruded sections of size75 mm x53mm, having wall thickness 2.0 mm (±0.2mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28mm x 30mm x 2mm thickness (±0.2mm) and 75mm x 200mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut jointed and fusion welded together, including providing and fixing 3 nos of 125mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer’s specification and direction of engineer-in charge. MTR 86.4 582.3 50310.72

37 0.000 Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after in serting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer’s specification and direction of engineer-in charge. Sqm 38.4 3792.5 145632

9.147E Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 min height dimension comprising of uPVC multi-chambered frame with in-built roller track and sas hextruded pro filed uly reinforced with 1.60±0.2mm thick galvanized mild steel section made from roll forming process of required length (shape& size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inlines as had aptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wiremesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100x8mm sizefor fixing frame to finished wall and necessary stainless steel screws etc .Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hard ware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes ,wiremesh and silicon sealent shall be paid separately). Note: For uPVC frame and sas hextruded profiles minus 5% to lerance in dimension i.e. in depth & width of profile shall be acceptable.

38 9.147E.1 Two track two panels sliding window madeof (big series) frame 67x50mm & sash 46x62mm both having wall thickness of 2.3±0.2mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) Sqm 45.9 7239.1 332274.69

0.0 Plaster And Finishing Work

13.11 12 mm cement plaster of mix

13.24 6 mm cement Plaster to ceiling of mix

40 13.24.2 1:4(1 cement;4 coares sand) Sqm 3803 125.6 477656.8

41 13.80A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Sqm 16430.7 105.4 1731795.7800000003

13.46.A Finishing walls with Premium Acrylic smooth exterior paint with silicone additives of required shade.

42 13.46A.1 New work (Two or more coats applied @ 1.43 ltr / 10 sqm. Over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm). Sqm 12856.7 132.5 1703512.75

13.48 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.

43 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm. Sqm 7077 117.3 830132.1

0.0 Repair Work

13.45 Finishing walls with textured exterior paint of required shade :

44 13.45.1 New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm Sqm 140 215.2 30128

13.94 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

45 13.94.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. Sqm 280 116.5 32620

46 14.43 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Sqm 280 7.7 2156

12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointingcompound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutoutsmade with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

47 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I Sqm 550 828.2 455510

0.0 Water Proofing Treatments Work

0.0 Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water-proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing applying a secoung coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300 x 300 mm square. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and specifed by the Engineer-in-Charge

48 22.8.1 With average thickness of 120 mm and minimum thickness at khurras point to be 65 .. Sqm 3803 850.7 3235212.1

0.0 Dismantling And Demolishing

0.9 Demolishing cement concrete including disposal of material within 50 metre lead:

50 15.3 Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material withing 50 metres lead: Cum 25.5 1411.2 35985.6

15.13 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead.

51 15.13.1 Of area 3 sqm and below Each 4 58.9 235.6

15.7 Demolishing brick work including stacking of serviceable material and disposal of unserviceable material within 50 meters lead:

52 15.7.4 In cement mortar Cum 26.25 823.7 21622.125

15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

53 15.23.2 For thickness of tiles above 25 mm and upto 40 mm Sqm 37.5 47.5 1781.25

54 15.6 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. Cum 112.5 219.3 24671.25

0.0 Horticulture And Landscaping

55 23.1 Trenching in ordinary soil upto adepth of 60 cm including removal and stacking of service able materials and thendis posing of by spreading and neatly levelling with in alead of 50 mand making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooding trench with water (encluding cost of imported earth,sludge or manure) Sqm 642 44.7 28697.4

56 23.2 Supplying and stacking of good earth at site including royalty but excluding carriage earth measusred in stacks will be reduced by 20% for payment) Cum 192.6 143.5 27638.1

57 23.3 Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment). Cum 96.3 282.6 27214.38

23.4 Supplying and stacking a site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

58 23.4.1 Screened through sieve of l.S. designation 20 mm Cum 96.3 278.9 26858.069999999996

59 23.5 Rough dressing the trenched ground including breaking clods. 100 Sqm 6.42 85.9 551.4780000000001

60 23.6 Uprooting weeds form the trench edarea after 10 to 15 days of its flooding with water including disposal of uprooted vegetation. 100 Sqm 6.42 283.2 1818.144

61 23.7 Fine dressing the ground 100 Sqm 6.42 208.8 1340.496

62 23.8 Spreading of sludge , dump manure or /and good earth inrequired thickness (Cost of sludge,dump manure or /and good earth tobe paid separately). Cum 96.3 30.1 2898.63

63 23.9 Mixing earth and sjudge or manure in porportion specified or directed. Cum 385.2 20.9 8050.679999999999

23.1 Grassing with 'Doob' grass including water In gand maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weed sand fit formo wing including supplying good earth if needed.

64 23.10.2 In rows 7.5 cm apart in either direction. 100 Sqm 6.42 670.8 4306.536

65 23.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clod sand mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20 %: one part of stacked volume of sludge or manure after reduction by 8% ). flooding with water, filling with earth if necessary , watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as drected, with in a lead of 50 mli ft upto 1.5 m complete (cost of sludge,manureor extra earth to be paid for separately). Cum 71.82 126.9 9113.957999999999

23.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludg einthe ratio of 2;1 by volume (2 parts of stacked volume of earth after reduction by 20%: 1 part of stacked volume of manure after reduction by 8%) flooding with water ,dressing including removal of rubbish and surplus earth, if any with all lead sandl if ts (cost of manure, sludge or extra good earth if needed to be paid for separately):

66 23.14.1 Holes 1.2 m dia, And 1.2 m deep. Each 10 536.5 5365

67 23.14.2 Holes 60 cm ciia. And 60 cm deep Each 20 69.3 1386

68 23.2 Filling mixture of earth and sludge or manure in the deisired proportion in trenches, flooding with water and levelling (cost of supplying earth and sludge or manure and mixing excluded). Cum 385.2 10.3 3967.56

69 23.24 Flooding the ground with water including making kiaries and dismantelling the same 100 Sqm 6.42 171.4 1100.388

Part-B Trees, Plants, Shrubs And Creepers

A Boundary Wall

70 5.12 Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. Each 15 322.9 4843.5

71 9.3 Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. Each 20 40 800

72 9.12 Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge Each 20 25 500

73 9.14 Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. Each 25 25 625

74 5.7 Providing and Displaying Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. in 25 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. Each 50 461.25 23062.5

75 5.31 Providing and Displaying Furcaira variegated well developed with fresh & healthy foliage 8 to 10 leaves in 30 cm Earthen Pot as per direction of the officer-in-charge. Each 20 225.5 4510

76 5.37 Providing and Displaying Phoenix roebelenii palm well developed having 20 to 25 fresh & healthy leaves 90 to 105 cm ht. in 30 cm Cement Pot as per direction of the officer-in-charge. Each 15 538.15 8072.25

77 6.8 Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge Each 60 20 1200

78 6.11 Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. Each 25 30 750

79 6.24 Providing and stacking of Setcreasea purpurea full of variegated leaves in 15 cm size of Earthen Pot/Plastic Pot as per direction of the officer-in-charge Each 25 20 500

80 7.1 Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge. Each 20 180 3600

C Entrance Step

81 5.3 Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. Each 15 41 615

82 5.14 Providing and Displaying Cycus revoluta in 35 cm challi, specimen , having 30 to 40 with fresh and healthy, leaves having 25cm to 30cm circumfrance of base stem well developed as per direction of the officer-in-charge. Each 20 1183.9 23678

83 5.29 Providing and Displaying Fishtail palm well developed with fresh & healthy foliage leaves of ht 210 to 240cm Specimen in 35 cm Cement Pot as per direction of the officer-in-charge Each 25 307.5 7687.5

84 5.31 Providing and Displaying Furcaira variegated well developed with fresh & healthy foliage 8 to 10 leaves in 30 cm Earthen Pot as per direction of the officer-in-charge. Each 25 225.5 5637.5

85 6.12 Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. Each 100 20 2000

86 6.24 Providing and stacking of Setcreasea purpurea full of variegated leaves in 15 cm size of Earthen Pot/Plastic Pot as per direction of the officer-in-charge Each 50 20 1000

87 8.25 Providing and stacking of Ficus panda of height 30-45 cm. with 3-4 branches and healthy foliage in p.bag of size 20 cm as per direction of the officer-in-charge. Each 20 35 700

0.0 HORTICULTURE CARRIAGE

93 2 DUMP MANURE Cum 96.3 187.54 18060.102

95 4 NEEL GIRI/MAXICAN GRASS TURF Sqm 5271 4.2 22138.2

96 Add 5.36% GST on SOR item As Per BCD 5875350.578756709

97 SIGNORANCE FEE 646770.72617824

PART-B PLUMBING SOR ITEMS

17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

98 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps nos 22 2764.4 60816.8

99 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. nos 22 1068.5 23507

17.2 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

100 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid nos 11 4230 46530

17.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

101 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests nos 10 4470.9 44709

17.4 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

102 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern nos 10 3723.2 37232

103 17.72 Providing and fixing white vitreous china flat back or wall corner type lipped roviding and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms nos 10 204.7 2047

8.1 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and

104 8.10.1 White Agaria Marble Stone sqm 25 3061.2 76530

105 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. nos 10 146.3 1463

18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

106 100 mm diameter nos 10 166.3 1663

18.58 Providing and fixing PTMT grating of approved quality and colour.

18.58.1 Circular type

107 18.58.1.1 100 mm nominal dia nos 26 33.2 863.2

0.00_ Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

17.60.1 100 mm inlet and 100 mm outlet

108 17.60.1.1 Sand cast iron S&S as per IS: 3989 nos 26 1129.2 29359.2

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.35 Providing and fixing soil, waste and vent pipes :

111 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 Metre 220 978.3 215226

17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

112 17.38.1.1 Sand cast iron S&S as per IS - 1729 each 150 530.7 79605

17.39 Providing and fixing plain bend of required degree..

113 17.39.1.1 Sand cast iron S&S as per IS - 1729 each 120 457.2 54864

17.41 Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :

114 17.41.1.1 Sand cast iron S&S as per IS - 1729 each 120 1038.8 124656

17.42 Providing and fixing double equal plain junction of required degree.

115 17.42.1.1 Sand cast iron S&S as per IS - 1729 each 110 861.2 94732

17.43 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

116 17.43.1.1 Sand cast iron S&S as per IS - 1729 each 130 671.2 87256

17.44 Providing and fixing single equal plain junction of required degree :

117 17.44.1.1 Sand cast iron S&S as per IS - 1729 each 150 580.2 87030

17.53 Providing and fixing sand cast iron S&S off sets as per IS-1729

17.53.1 76 mm off sets

17.53.1 114 mm off sets

119 17.53.2.2 With 100mm dia pipe Each 50 560.1 28005

17.53.3 152 mm off sets

120 17.53.3.2 With 100mm dia pipe Each 50 666.3 33315

17.55 Providing and fixing door piece, insertion rubber washer 3 mm thick, bolts & nuts complete.

121 17.55.1.1 Sand cast iron S&S as per IS-1729 Each 60 711.3 42678

17.56 Providing and fixing terminal guard:

122 17.56.1.1 Sand cast iron S&S as per IS-1729 Each 50 392.9 19645

17.57 Providing and fixing collar

123 17.57.1.1 Sand cast iron S&S as per IS-1729 Each 30 399.6 11988

17.58 Providing lead caulked joints to sand cast iron / centrifugally cast (spun) iron pipes and fittings of diameter.

17.59 Providing and fixing M.S stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter:

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

126 18.8.1 15 mm nominal outer dia Pipes Metre 100 278.2 27820

127 18.8.2 20 mm nominal outer dia Pipes Metre 70 350.8 24556

128 18.8.3 25 mm nominal outer dia pipes Metre 50 463.1 23155

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

129 18.7.2 20 mm nominal outer dia Pipes Metre 50 233.9 11695

130 18.7.3 25 mm nominal outer dia Pipes Metre 50 317.3 15865

131 18.7.4 32 mm nominal outer dia Pipes Metre 30 395.2 11856

132 18.7.5 40 mm nominal outer dia Pipes Metre 45 538.4 24228

133 18.7.6 50 mm nominal outer dia Pipes Metre 350 791 276850

18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

134 18.17.1A 20 mm nominal bore. nos 10 465.4 4654

135 18.17.1 25 mm nominal bore nos 10 532.3 5323

136 18.17.2 32 mm nominal bore nos 10 589.9 5899

137 18.17.3 40 mm nominal bore nos 10 707.3 7073

138 18.17.4 50 mm nominal bore nos 10 878.2 8782

18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

139 18.18.1 15 mm nominal bore nos 50 348.9 17445

140 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. per liter 40000 9.7 388000

0.00_ Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts,nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

141 18.60.1 50 mm dia nominal bore each 2 3533.7 7067.4

142 18.65 Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms. Each 10 96.8 968

18.75 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.

143 18.75.3 25mm nominal bore, weighing not less than 62 gms each 10 100.6 1006

144 18.77 Cutting holes up to 15 x 15 cm in R.C.C floors and roofs for passing drain pipe and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof. Each 10 217.1 2171

17.34 Providing and fixing toilet paper holder :

146 17.22A Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. nos 32 886.2 28358.4

18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

148 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : nos 40 434.2 17368

18.32 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation,foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :

149 18.32.1 With common burnt clay F.P.S.(non modular) bricks of class designation 100A No 20 1177.9 23558

2.1 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:

2.10.1 All kinds of soil

150 2.10.1.2 Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia Metre 1500 391.7 587550

12.78 Providing and fixing on wall face PVC (working pressure 4kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

151 12.78.2 110 mm diameter Metre 800 257.5 206000

12.79 Providing and fixing on wall face PVC moulded fitting / accessories for rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

12.79.1 Coupler

12.79.2 Single pushfit Coupler:

12.79.3 Single tee with door

12.8 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50 x 50 x 50 mm hard wood plugs, screwed with M.S screws of required length, including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

157 12.81 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. Each 35 47.9 1676.5

19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

162 19.4.1 100x100 mm size P type

163 19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 3 1860.6 5581.799999999999

0.0 Providing, laying and jointing glazed stoneware pipes class 'SP1' with stiff mixture of cement mortar in the proportion of 1:1(1 cement: 1 fine sane) including testing of joints etc. complete.

164 19.1.2 150 mm diameter Metre 10 464.3 4643

0.0 Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coase sand: 10 graded stone aggregate 40 mm nominal size) all-round S.W pipes including bed concrete as per standard design.

165 19.3.2 150 mm diameter S.W. pipe Metre 10 311.4 3114

19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

166 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 4 7914.7 31658.8

19.9 Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design

19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

167 19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 1 7090 7090

168 19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be isible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. each 150 310.9 46635

19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

169 19.19.3.1 Circular shape 560 mm internal diameter each 5 985.1 4925.5

19.27 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :

170 19.27.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 50 3743.3 187165

19.29 Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame and vertical grating complete as per standard design :

171 19.29.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 25 7186 179650

0.0_ Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

24.1.1 All types of soil

0.0_ Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

173 24.3.3 200 mm nominal size dia mtr 300 940.8 282240

174 24.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. cum 160 1188.9 190224

175 24.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. cum 160 1195.6 191296

176 24.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. cum 160 1195.6 191296

177 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. cum 160 1343.2 214912

PLUMBING BORING

24.1 Boring/drilling bore well of required dia for casing/strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. (All types of soil)

24.2 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools,plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

24.3 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC (UPVC) medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

181 24.3.2 150 mm nominal size dia P/M 0.0 660.1 198030

182 24.3.1 100 mm nominal size dia P/M 0.0 546.1 163830

24.4 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC (UPVC) medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

183 24.4.1 100 mm nominal size dia P/M 0.0 573.1 171930

24.13 Supplying the following fittings & fixing the same in position as per approved lowering assembly and strata chart including providing all equipments and welding the same on process of lowering the assay etc. all complete as per S/D of E/I.

184 24.13.2 150 mm dia well cap Each 2 210.7 421.4

24.14 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

185 24.14.2 (b) 150 mm dia M.S. Clamp 1.6 M long (one Pair) Each 2 1531.4 3062.8

24.15 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

186 24.15.1 100mm dia & 6mm thick M.S. well shoe plug Each 2 228.3 456.6

187 24.6 Providing all materials, labours, & equipments for fixing tube well with pea gravel of Dalbhumigarh to size 4mm to 8mm approx. as suitable for strata including carriage washing, placing and packing the same in position around the tube well etc. all complete as per direction of E/I. P/M3 0.0 1195.6 21520.8

188 NS-1 Transportation of drilling plants, developing equipments & all other required tools and M/c by and suitable mechanical means including all cost of loading, unloading, placing at work site and back after completion of work as per S/D of E/I Each 4 10640 42560

189 NS-2 Supplying all materials and labours for arrangement for additional water required during the drilling period for 70 Hrs & site clearance & leveling etc. And providing the soap duster etc. to staff engaged in drilling etc. all complete work as per specification & direction of E.I. Each 4 7980 31920

190 Add 5.36% GST on SOR item As Per BCD 335538.412

PART-C ELECTRICAL SOR ITEMS

1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch ,modular plate suitable size G.I box etc as per requred.

192 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. Metre 5500 309 1699500

0.0_ Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

193 1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 3000 201 603000

194 1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 2000 246 492000

195 1.7.3 2X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 220 309 67980

195 1.7.4 2X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 5300 422 2236600

1.21 Supplying & fixing of following size medium class PVC conduit along with accessories in surface/ recess including cutting of wall and making good the same in case of recessed conduit as required.

1.24 Supplying and fixing following modular switch/ socket on the existing modulor plat & switch box/ including connections but excluding modular plate etc .as per required etc.

198 1.24.1 5/6 amps switch Each 241 82 19762

199 1.24.2 2 way, 5/6 amps switch Each 20 131 2620

201 1.24.4 3 pin , 5/6 amps socket outlet Each 241 112 26992

202 1.24.5 6 pin , 15/16 amps socket outlet Each 315 183 57645

203 1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as required. Each 185 358 66230

204 1.26 Supplying and fixing modular blanking plate on the existing modular plate & metal box excluding modular plate, etc. as required. Each 150 34 5100

1.27 Supplying and fixing following size/ modules, Gl box along with modular base and cover plate for modular switches in recess etc as required.

211 1.33 Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. Each 150 64 9600

212 1.34 Supplying and fixing batten/ angle holder including connection etc. as required. Each 150 80 12000

1.59 Wiring for group controlled (looped) light point/ fan point/ exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit etc as required.

2.4 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

214 2.4.7 4OO A, 50 KA, FPMCCB Each 1 45651 45651

215 2.4.20 8OO A, 50 KA, TPMCCB Each 1 38599 38599

2.7 Providing and fixing following capacity four pole ON-load panel mounted changeover switches inside the existingcubical panel board including drilling holes in cubicle panel, making connections etc. as required.

2.8 Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, inter connections, powder painted including earthing etc. as required. (But without MCB/RCC Bilsolator)

217 2.8.2 2+4 way, Single door Each 133 1399 186067

218 2.8.7 12 way, Double door Each 6 2314 13884

2.9 Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. as required, (But without MCB/RCCB/lsolator)

219 2.9.3 8 way ( 4 + 24 ), Double door, horizontal type Each 7 6199 43393

2.12 Supptying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

220 2.12.1 6 A to 32'A, Single pole Each 726 237 172062

2.13 Supplying and fixing following rating, 2401475 volts, "C"curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

221 2.13.1 6 A to 32 A, double pole Each 130 667 86710

222 2.13.3 40 A to 63 A, double pole Each 20 1198 23960

223 2.13.4 40 A to 63 A, four pole Each 20 2324 46480

2.18 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

226 2.19 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. Each 35 1513 52955

227 3.2 Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required. set 25 6323 158075

228 3.4 Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required. set 6 6884 41304

229 3.6 Earthing with copper earth plate 600 mm X 600 mm X 3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required. set 6 13721 82326

230 3.7 Supplying and laying 6 SWG G.l. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with Gl thimble as required. Meter 1500 37 55500

231 3.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of brass nut bolt and & spring washer spaced at 50mm) Meter 130 1026 133380

232 3.9 Supplying and laying 25 mm X 6 mm G.t. strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with GI nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of G.l. nut bolt & spring washer spaced at 50 mm) Meter 225 133 29925

233 3.10 Providing and laying 25mm x 5mm Copper strip in 40 mm. Dia copper pipe from earth electrode including connection with brass nut, bolt, washer, excavation and refilling etc. as required. Meter 50 1628 81400

234 3.11 Providing and laying 25mm x 5mm G.I. strip in 40 mm. Dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as required. Meter 250 721 180250

235 4.1 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having singte prong on top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required. set 10 1056 10560

236 4.4 Jointing copper/ G.l. tape (with another copper/ G ltape,base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required. set 10 81 810

237 4.6 Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run) M 50 559 27950

5.7 Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

240 5.10 Supplying and fixing 70112 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,lP 65 protection and complete u.,ith integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required. Each 40 1275 51000

241 5.13 Supplying and fixing post top / gate light (width 250/300mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( Butwithout lamp) Each 15 1399 20985

5.14 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

5.15 Supplying and fixing fotrlowing types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on poleibuilding including connection earthing the body etc as required

6.1 Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

244 6.1.7 20 watt LED lamp Each 15 267 4005

6.3 Supplying and fixing of following types LED electronic driver in the existing LED street Iight etc as required.

245 6.3.4 For 90 watt LED street light Each 30 2674 80220

6.4 Supplying and fixing of following types LED electronic driver in the existing LED Flood light etc as required.

246 6.4.4 For 100 watt LED Flood light Each 40 2247 89880

0.0_ Laying of one number additional PVC insulated and pVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

248 7.2.2 Above 35 sq. mm and upto 95 sq. mm Each 400 232 92800

249 7.2.4 Above 185 sq. mm and upto 400 sq. mm Each 150 274 41100

0.0_ Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

7.8 Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

255 8.9 Supply and fixing pole mounted junction box/fuse box for single phase/ 2 core low wattage street light pole with all accessories and connection etc. as required. Each 20 825 16500

256 8.15 Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required. Each 185 2482 459170

8.17 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

8.22 Supply and erection of 6 metre height Hot-dip galvanized octagonal street Iight pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

260 2301 4 Metre height Octagonal Hot-Dip galvanized street light poles with top dia. (A/F) 70 mm & bottom dia (A/F) 130 mm and made of 3 mm thick sheet, base plate diamension 220 X 220 X 12 mm including suitable size foundation bolts etc. Each 15 9500 142500

9.15 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part ll complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. ln the existing trench, complete as required.

261 9.15.5 200 mm dia (OD-200 mm & lD-175 mm nominal) metre 250 646 161500

9.16 Providing and making of following sizes octagonal street light pole foundation in reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) of specified size including PVC conduit, form work, curing, reinforcement, excavation and refilling etc. as required.

262 9. 16.1 For 4 metre pole (500mm X 500mm X 1000mm) Each 15 3305 49575

263 9.16.2 For 6/7 metre pole (500mm X 500mm X 1400mm) Each 20 4398 87960

DSR-2022 CABLE TRAY

DSR 4.1 Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

264 DSR 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness RM 200 604 120800

265 DSR 4.1.3 200 mm width X 50 mm depth X 1.6 mm thickness RM 200 689 137800

266 DSR 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness RM 150 777 116550

PART-D FIRE FIGHTING SOR ITEMS

4 Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

(b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

(d) Suitable cement concrete foundation duly plastered and with anti vibration pads

7 Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

268 7.6 80mm nominal dia Rmt 30 951 28530

269 7.7 100mm nominal dia Rmt 350 1316 460600

9 Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

270 9.1 Single headed Gunmetal Set 9 7245 65205

11 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

273 13 Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. each 9 1236 11124

14 Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

15 Providing, installation, testing and commissioning of stainless steel Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

16 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

276 0.0 Gunmetal Set 18 5206 93708

17 Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. "Connections from riser with 25 mm dia stop gun metalvalve & M.S. Pipe and socket."

18 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

278 0.0 Gunmetal Set 9 2393 21537

19 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

279 0.0 2 way-100 mm dia M.S. Pipe Set 4 6331 25324

280 20 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Set 4 17707 70828

281 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. per liter 80000 9.7 776000

PART-E HVAC DSR-2022 ITEMS

AIR DISTRIBUTION WORK

16.12.1-DSR-2022 FACTORY FABRICATED DUCTS

Supply, fabricating, Installation, testing and commissioning of G.I Sheet metal rectangular/round ducting (supplied in L-Section for rectangular duct) complete as per class VIII conforming to IS 277-1962 (revised). The fabrication of duct shall strictly conform to ISS 655- 1963. along with supports, nuts, bolts. Support shall be considered at an interval of 3.0 mtrs and on all branches. All supports should be made of galvanised steel angle with drilled holes & GI threaded rods with check nuts & washers of Hilti with support from roof of Gripple/Equivalent make. Measurement shall be made based upon effective duct area, Contractor to bid accordingly. 2.5 mm to 3 mm thick self adhesive normal gasket for Ducting as per OEM specifications to be considered.

282 16.12.1.1-DSR-2022 Thickness 0.63 mm sheet m² 35 1080 37800

GRILLES & WIREMESH

Supply, installation, testing, balancing & commissioning of Extruded Aluminium construction Grilles. The grilles will be powder coated in shade approved by Client and installed as per approved shop drawings and specifications. The grilles may be double or single louvered, adjustable or fixed as required by Client.

283 16.15-DSR-2022 Grille with VCD m² 1 9105 9105

BILL OF QUANTITY FOR NON SOR ITEMS

Development of Tourist Facilities at Sonepur Mela Ground, Saran, Bihar

Bill of Quantity

(Each Item rate must be filled)

S.NO S.NO/SOR Description of Work Unit Qnty Amount (Rs.)

PART-A CIVIL NS ITEMS

1 Supply of GFRC Jali panels (custom design as per approved concept by Architect and Engineer in Charge) Includes mold design, casting, and curing. Technical specs • Thickness: Typically 18–24 mm • Compressive Strength: 40–80 MPa • Flexural Strength: 10–30 MPa • Dry Density: 1.8–2.1 t/m³ • Fiber Content: 2–5% by weight • Curing: 7 days under polythene or polymer curing compound • Finish Options: Sandstone, marble, antique, or custom paint Optional: antique, sandstone, marble effect. Precision cutting with diamond tools.Includes protective packaging. SS clamps, epoxy grout, or mechanical fasteners. Includes surface sealing if required. Design Approval: All jali patterns must be approved by architect/client before casting. • Tolerance: Dimensional tolerance ±2 mm. • Installation: Must comply with façade safety standards and wind load requirements. • Warranty: Minimum 5 years against structural defects and weathering. Sqm 709.5

MR-2 CNC-cut 2D metal Elephant profile artistic installations

2 Design, detailing, and fabrication of CNC-cut 2D metal Elephant combination of one Full size and one small size (custom design as per approved concept by Architect and Engineer in Charge) Must meet corrosion resistance and aesthetic standards. Finish as per artistic intent and environmental exposure. Fixed on top of gate with RCC pedestal or steel base with anchoring bolts. Artistic enhancement and nighttime visibility. Material Grade: Use corrosion-resistant metals like SS 304/316 or Corten steel depending on climate and exposure. • Finish Quality: Surface finish must be uniform, free from blemishes, and aligned with the artistic vision. • Structural Integrity: Must withstand wind loads, seismic activity (if applicable), and vandalism. • Installation Safety: All lifting and fixing must comply with local safety codes and engineering standards. • Documentation: Include soft drawings, artist’s concept approval, and structural calculations. Num 4

MR-3 Immersive Room - 1,2,3 and 4

A Projector Display

4 i 7000 Lumen, WUXGA with 4K Enhancement, 1.35-2.20 Throw Ratio, Laser Light Source, 20,000 Hrs typical life, 3 Chip LCD Projector, 400W typical power consumption Epson/Christie/Barco 16

5 ii 5000 Lumen, HD with 4K Enhancement, 0.16-0.22 Throw Ratio, Laser Light Source, 20,000 Hrs typical life, 3 Chip LCD Projector, 400W typical power consumption Epson/Christie/Barco 6

B Immersive Scenography

6 i Providing and fixing Glass Fibre fibber-reinforced polymer (Live Size Human Sculpture):- (GFRP) Sculpture (Life Size) as per architectural intent drawing & intent images. The GFRP work shall include: a) Providing sculpture drawings, based on the architectural intent drawings and intent images for sculpture and obtaining approval from the Curator & engineer in charge. b) Providing samples up to 0.04 sqm or 0.008 cum in size, wherever necessary, in approved colours, shades and finish, representing the product in actual colour, textures and patterns etc. as directed. c) Preparing necessary Molds made out of fibreglass/steels/wood/rubber etc. in accordance with approved drawings. d) Fabrication of sculptures as per approved drawing and samples by using approved mix of polyester or epoxy resin by spray process along with alkali resistant glass fibre. The glass fibre shall be laid in 3 layers on top of one another, with each layer oriented in various preferred direction and necessary quantities of mables gravel/silica sand added to obtain the required finish. All anchorage points for anchors shall be provided with concealed reinforcement, as required, each unit shall be marked with permanent serial number coordinated with sculpture drawing designators and shall be properly cured and cleaned before installation. Care shall be taken to carefully remove all toxic material harmful to plant/animal or building materials. The fabricated sculpture shall be strictly in accordance with the approved drawing and sample, in approved colours and textures. All glass fibre-reinforced plastic fabrications shall be moulded surface coat over polyester resin laminate reinforced with glass fibre structural reinforcing as required with 1. Surface coat: Ultraviolet inhibited NPG-ISO polyester gel coat 0.5mm thick, nominal. 2. Surface coat: Polyurethane, 3. Colour: as approved 4. Texture on exposed side as approved. 5. Resin: Isophthalic polyester resin with low flame spread, low smoke and low heat distortion. 6. Glass fibber: ""E"" type random chopped fibres. 7. Glass content: 15 percent by weight maximum.8. Shell thickness: 5mm minimum,9. Flexural strength:138 MPa, 10. Modulus of Elasticity: 6200MPa,11. Tensile strength: 83 MPa,12. Compressive strength:117 MPa,13. Bearing strength:62 MPa 14. Thermal expansion coefficient: 5.56x10^-6 degree C. 15. Specific gravity: 1:5,16. Variation in thickness, from nominal: Minus 1.5mm, plus 6 mm 17. Variation in thickness of gel coat: +/-0.06mm, maximum, 18. Variation from dimension indicated on drawings: +/- 3mm, maximum,19. Variation of hardware from intended location: +/- 6mm, maximum. All sculptures shall be properly installed, as directed over properly constructed substrates. All substrates must be in correct lines, levels and true Custom 16

7 ii Providing and Fixing Glass Fibre fibber-reinforced polymer (Live Size Animal Sculpture) (GFRP) Sculpture (Life Size) as per architectural intent drawing & intent images. Elephant, Horse, Cow, Bull, Camel, Goat, Hen, Dog. Custom 20

8 iii GFRP Bust with Pedestal:- Providing, supplying and installing approximately 2X 'true size' busts including GFRP mounting pedestal for each bust as per architectural intent drawings/details, as approved and directed. Sample clay models of each bust shall be submitted for approval and necessary changes/modifications carried out and fresh sample submitted, wherever required and the work executed only in accordance with the approved sample. Bust size: 900mm x 600mm Custom 14

9 iv Providing and making decorative wall painting - sq. ft. (concept paintings) at all heights and levels in accordance with approved architectural intent drawing and approved sample. The work shall include all necessary cost of labour, skilled artist/painter all material, T&P, scaffolding at all heights, leads and lifts etc. Appling necessary priming coat and approved wall putty and/or all other necessary surface preparation work as required and as directed. Item is also inclusive of providing 2m x 2m sample of the decorative wall painting in true colours and finish for approval purpose. All concept painting work must be carried out as per samples as approved by the Curator & Engineer in charge. Item is for complete fully finished works, including base preparation works and additional payment whatever shall be made on any account. Custom 1500

10 v High Relief Mural (GFRP/Cement)-sq. ft. Providing and making decorative high relief mural on wall at all height and level using white/grey cement as the base material, mixed with fine/coarse sand/aggregates as required and directed in approved colours and textures including and undercoat of 12mm thick plaster in 1:4 (1 cement & 4 fine sand). The high relief decorative mural shall involve wall art to create bamboo mats/screens and other forms in accordance with the intent architectural drawings and other details. Item is inclusive of all necessary curing, cost of all skilled artist/painter, all labour and materials, T&P, scaffolding at all heights, leads and lifts involved in execution of the complete works. Item is also inclusive of providing 1m x 1m decorative high relief mural sample in required forms, pattern, shapes and colours for approval purpose, before commencement of the specific mural work. All decorative high relief mural work must be carried out as per sample as approved by Curator & Engineer in charge. Item is for complete fully finished works, including any necessary base preparation works and no additional payment whatever shall be made on any account. Custom 500

11 vi Decorative Three Dimensional Painting -sq. ft. Providing and making decorative three dimensional wall painting at all heights and levels in accordance with approved architectural intent drawing and approved sample. The work shall include all necessary cost of labour, skilled artist/painter all material, T&P, scaffolding at all heights, leads and lifts etc. Appling necessary priming coat and approved wall putty and/or all other necessary surface preparation work as required and as directed. Item is also inclusive of providing 1m x 1m sample of the decorative three dimensional wall painting in true colours and finish for approval purpose. All three dimensional painting work must be carried out as per samples as approved by the Curator & Engineer in charge. Item is for complete fully finished works, including base preparation works and additional payment whatever shall be made on any account. Custom 1500

12 vii Canvas with frame (4x5ft) Canvas print with frame of rare old pictures of Sonpur mela UV print on canvas with highly detail with DPI 300. Canvas frame as per approved images of mela & design. Providing and making Canvas at all heights and levels in accordance with approved images and approved sample. The work shall include all necessary cost of labour, skilled artist/painter all material, T&P, scaffolding at all heights, leads and lifts etc. All canvas work must be carried out as per samples as approved by the Curator & Engineer in charge. Item is for complete fully finished works, including base preparation works and additional payment whatever shall be made on any account. Custom 4

C Content Production

13 i Cost of 4K visual production, including scripting, concept design, storyboarding, archival research, animation, and post-production of synchronized rich media content, ready for transfer to media servers. Custom 4

14 i Single emission projectors for indoor application. The warm white LED light source with Very Narrow light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 439 lm, with a 110 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium and features a white finish, processed by means of powder coating. The ingress protection degree is IP20; the total weight is of 0.2 kg. The total absorbed power is 4 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. The device features protection class II and can be ceiling-mounted. Line alight / Endo / CNC / Forma 7

15 ii Single emission projectors for indoor application. The warm white LED light source with Medium light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 1948 lm, with a 110 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium and features a white finish, processed by means of powder coating. The ingress protection degree is IP20; the total weight is of 0.3 kg. The total absorbed power is 18 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. The device features protection class II and can be ceiling-mounted. Line alight / Endo / CNC / Forma 7

16 iii Single emission projectors for indoor application. The warm white LED light source with Narrow light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 1703 lm, with a 110 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium and features a white finish, processed by means of powder coating. The ingress protection degree is IP20; the total weight is of 0.3 kg. The total absorbed power is 12 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. The device features protection class II and can be ceiling-mounted. Line alight / Endo / CNC / Forma 7

17 iv Advanced, multi-functional LED track mounted projector, tiltable vertically 0°-90° and rotatable horizontally 350°. With built-in bidirectional zooming lens with sharpness adjustability, and lens rotation. Adjustable shutters to re-frame the beam to the desired size and shape (circle, square/rectangle, or irregular four-sided shapes). High-precision optics for sharp outlines and high degree of lighting uniformity. The warm white LED light source with farmable distribution is composed of LEDs with CCT of 3000 K and a CRI 90;The ingress protection degree is IP20; The total absorbed power is 25 W. Casambi LED Driver is included with the fixture, Motion Control: Casambi, Dimming Options: Casambi. Line alight / Endo / CNC / Forma 7

18 v Single emission recessed downlights for indoor application. The Warm white LED light source with a wide flood light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 2352 lm, with a 117 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium end ab - 46100 and features a White finish, processed by means of powder coating; the diffuser is made of uv resistant polycarbonate. The ingress protection degree is IP20; the total weight is of 0.2 kg. The Non Dim power supply is to be Provided separately. Accessories like Spread Lens and Honeycomb Louvre to be provided Separately. The total absorbed power is 19.8 W. The power supply cable is included and features a 0.300 m length. The device features protection class III and can be ceiling-mounted, with a 65 mm diameter hole (in plasterboard). Line alight / Endo / CNC / Forma 7

19 vi Single emission recessed/surface upplight for indoor application. The Warm white LED light source with a wide flood light distribution is composed of LEDs with CCT of 3000 K and a CRI 90; the source luminous flux is 762 lm, with a 98 lm/W nominal luminous efficacy. The device body is made of die-cast aluminium end ab - 46100 and features a White finish, processed by means of powder coating; the diffuser is made of uv resistant polycarbonate. The ingress protection degree is IP20; the total weight is of 0.6 kg. The Non Dim power supply is to be Provided separately. The total absorbed power is 9.4 W. The power supply cable is included and features a 0.300 m length. The device features protection class III and can be ceiling-mounted, with a 100 mm diameter hole (in plasterboard). Compliant with the EN 60598-1 standard and its specific provisions. Line alight / Endo / CNC / Forma 7

E Audio Systems

20 i Slim Column Speaker Slim Column Speaker,600MM,BLK,1PC JBL / D&B / Meyer 16

21 ii Power Subwoofer 2 x 10" High Output Compact Subwoofer; Power Rating 400W continuous at 8 Ohms; etc. JBL / D&B / Meyer 4

22 iii Digital Power Amplifier CDi Series, Network Based Digital DriveCore Multichannel Power Amplifier with 4 x 600W; built-in DSP and BLULink, etc. Crown / D&B / Meyer 4

23 iv Audio Interface Audiophile 18x20, 24-Bit/96 kHz USB Audio/MIDI Interface BSS / D&B / JBL 4

24 F Backend Infrastructure

25 i LCD Monitor ViewSonic / Dell /Samsung 1

26 ii 19'U Server Rack D-Link / Walpack / Netrack 1

27 iii Wireless Keyboard Mouse Combo Logitech / Dell 1

28 iv Playout Controller Intel Based Media System 8

29 v Playout Software for calibration, edge blending and projection mapping. Watchout / Pixera/Touch Designer 8

30 vi Cables and Networking Belden / Manhattan/Light ware 1

31 vii Projector Celling Mount Kit Custom 24

32 viii Drawings, System Integration and Onsite Programming. LOT 1

33 ix Sitework and TBL LOT 1

MR-4 INTERIOR WORK

35 1 Reception Area- Designer Wall Paneling with Italian Marble and Louvers; Fabricating and Designing of Wall panel of size 6m (W) X 8M(H) with fixing WPC Board base on vertical wall with the screw and Hitex glue for leveling the wall. Fixing of Louvers on this base and in the middle of wall design of white Italian marble to create the design as per architectural standards with fixing of polished teak wood border design on wall in required shape in between Italian marble and louvers to create an aesthetical look on wall in reception area with provision of fixing profile light. The above work will be finished as per E/I and architect design. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. Sqm 11

36 2 Providing and fixing of Experience Centre Name and Logo made of Acrylic sheet as per stander size required in architectural design given. Provision of Back lit will be provided in Name and logo as per approval of Engineer-in-charge. No. 1

37 3 Reception Counter: Providing and fixing of Reception counter of size 5400x750x750/1050mm (H) to be made of 19mm thick BWP ply of century/Green make for all surfaces with the working top of size 750mm width at 750mm level and the customer top of 300mm width at 1050mm level. There after a double layer of Flexi ply (12mm + 06mm thick) is to be fixed with necessary fittings to the block board and flexi ply is to be curved in half round shape in both side of billing counter. The front modesty panel is to be made of ply and flexi ply as required and on that a 12mm thick corian material of approved shade and make as per drawing and design. Solid surface material is to be fixed with acrylic epoxy adhesive compound including surface and edge finishing and modesty panel and mold to make the interior aesthetical look. All exposed surfaces will be finished with 1mm mica of century/Green make. Three sets of drawer chest with two drawers and one cupboard with concealed hinges and lock and key will be provided with billing counter along with key board tray on telescopic channel for smooth movement. Access flap and wire manager to be provided for electric/Data cables. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 1

38 4 Wooden Chair: Providing and fixing wooden chair made of seasoned teak wood. Back & seat cover cushion chair uphlostered in fabric. All wood shell be polished in PU Matt polish. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 54

39 5 Supplying and fixing Modular Cabin table i. MAIN TABLE SIZE - 2100MM W x 900MM D X 750MM H, ii. The worktop Will be in single piece made up of prelaminated particle board. iii. The worktop shall be made of 36mm thick prelaminated particle board with 2 mm thick hot melt PVC edge banding from REHAU iv. The worktops shall be provided with metallic inserts for precise alignments and longer life. v. The top is resting on the vertical strips of particle board. vi. The modesty of the table is also made up of 18 mm thk. prelamianted particle board which is attached table top. With the horizontal panels created under as second top under main vii. The side panels are also made up of 25mm thick prelaminated particle board with 2 mm thick hot melt PVC edge banding from REHAU vii. Complete hardwares to be used from EBCO. Table will be provided a Side unit of size 1050x450x750mm which should have two drawer on top with hinge shutter credenza under it. Made up of prelaminated particle board with 2mm thk. PVC edge bending from REHAU. Complete hardwares to be used from EBCO. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

40 6 Back Unit - Back Unit (W)2000mm X (D)500mm X (H)750mm. File Cabinets And Multipurpose Storage Units For The Contemporary Workspace. Constructed From Engineered Wood And Finished In Black Oak For A Superior Feel And Finish. The Unit Comprises Of Long Stacked Horizontal Shelves Encased In Wooden Shutters. The File Cabinet And Sideboard Is A Perfect Addition To The Wall Or On The Side Next To The Theon Office Desk For Storing Your Files, Documents And Important Papers, all complete as per direction of E/I. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 1

41 7 EXECUTIVE LEATHERETTE REVOLVING CHAIR (High Back) of approved make. The seat and back are made up of 1.2cm thick hot pressed plywood and upholstered with pure leather of required color and moulded Polyurethane foam. BACK SIZE: 520mm. (W) X 700mm. (H), SEAT SIZE: 520mm. (W) X 510mm. (D) The chair should have 360 degree Revolving type, Front pivot synchro tilt mechanism, 5-position locking with anti-shock back mechanism. The High Resilience Polyurethane foam is moulded with density=45+/-2 kg/m cube and hardness load 16+/-2 kgf as per IS: 7888 for 25% compression. The seat and back are arrested together with a 9.0cm (W) spine made of 0.8cm thick HR steel.. It is fitted with 5nos. twin wheel castors. The pedestal is 67.0cm pitch-center dia (77.0 cm with castor). The twin wheel castors are injection moulded in Black Nylon.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

42 8 Visitor Office chair contemporary design, all black finish or as per choice of E/I, double padded cushion encased in an all black leatherette, or approved equivalent. The side padding and the headrest provide added lumbar support to the user. Material & Sub type Leatherette Colour Family Black Dimension (W)610mm X (D)505mm X (H)990mm Back Type Low Back Base Cantilever Frame Base Type Cantilever Maximum Seating Height19", all complete as per direction of E/I.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 4

43 9 3-Seater sofa of size 1920x750x740mm. The inside Frame is made of seasoned wood and has anti termite treatment. The seat and back are made of high density foam and is finished in leatherette upholstery. The frame base has webbing for supporting the cushions. The complete sofa body has polyurethane foam in desired shape.Foam of sofa will be comfortable cushion with high density and resilent foam. All upholstery materials used in specially designed and all ply wood used in MR grade. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

44 10 Wooden Centre Table: Size 1130x630x410mm (H) The Centre table is made keeping in mind the comfort with decorative glass top of toughened glass . The table is a gorgeous piece of furniture to highlight the room. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below t5he glass provide the glass with a focal point and some support. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

45 11 Wall paneling: Providing and fixing of wall panel made out of 2”x1” xCPT wood frame work at every 1.6” c/c(Vertical / Horizental) both ways, covered with 12mm thick ply all exposed surface of the paneling shell be finished with approved colour 1mm thick laminate complete as per detail drawing and instruction of E/I. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. Sqm 50

46 12 Toughened Glass : Providing and fixing of toughened glass of required shape and size. Sqm 2

47 13 Place Marker : Printed Text on sign board: Providing, fixing and installation of Signages made with premium quality vinyl sheet pasted on 05mm thick sun board. Size 150x450mm No. 1

48 1 Dining Chair: Providing and installation of café chair of the following specifications. The seat and back shall be one piece injection moulded in high impact strength poly propylene. The dimensions of seat shall be 52.5cm(W) x 53.2cm (D) and of back shall be 51.6cm (W) x 40.5cm(H).The tubular welded frame is made from dia 2.22+/- 0.03 x 0.12+/- 0.0128cm and 3.5+/- 0.03cm x 1.5+/-0.03cm x 0.12+/-0.0128cm. The tubes are buff polished to give shiny finish. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. Nos 36

49 2 VIP Stacking chair for VIP Launge : Providing and fixing chair make as approved quality of paris is a that parts fit this lounge chair it exudes style and boisterous come with its bold pattern upholstery . The supple gray fabric complements the solid legs up on which tghe chair is set for a firm sturdy base bring home some chic style with paris out. Newest lounge chair for the long time sitting. Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 10

50 3 Dining table: Providing and fixing of dining table in round shape The top of the table will be 30 mm thick including 18mm ply and 12mm White granite top table. Unrestructured of the table will polished seasoned wood of specially designed. The table top will be pasted with chemical adhesive finished with corners edging incuding rubbing, curing, moulding and polishing to the edges to give high gloss finish complete at all levelsMake VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 6

51 4 Cash Counter: Providing and fixing Cash counter of size 4500x750x750 (H) to be made of 19mm thick BWP ply of century/Green make for all surfaces with the working top of size 750mm width at 750mm level. All exposed surfaces will be finished with 1mm mica of century/Green make. Two sets of drawer chest with two drawers and one cupboard with concealed hinges and lock and key will be provided with billing counter along with key board tray on telescopic channel for smooth movement. Access flap and wire manager to be provided for electric/Data cables.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 1

52 5 Providing and fixing MEDIUM BACK EXECUTIVE REVOLVING CHAIR with adjustable lumber support in mesh back with armrest with PU pad. The back of the chair will be provided adjustable support on head and neck for extra comfort. The seat is made up of 1.2cmm thick hot pressed plywood, upholesterse with fabric and moulded polyurethane foam. and center tilt synchro Mechanism, Peneumatic Height Adjustment. The pedestal is with twin wheel injection moulded casters.Make VINAR, DURIAN, GODREJ or equivalent as per approval of Engineer-in-charge. No. 2

53 6 Kitchen Island Unit with Two Burner Range : Kitchen Island Unit made of Stainless Steel Sheet and SS Square Frame with Two Burner Range of total size 12’W x 2.5’D with height 32” and 28” will be in two parts fitted with drawer for keeping spices and salt below cook top. A sliding shelf will be provided under the cook top & drawer for the store of waste cooking materials, additional shelf will be given in bottom for keeping cooked food. In another part a ss sink with swan head tap will be fitted. And also making arrangement for keeping LPG cylinder inside a covered cupboard along with three drawer unit for keeping kitchen items. The material used in fabricating the above items is such as Top Sheet 18 guage, Shelf & facia will be in 22 guage in 304 Grade, Legs & Frame -- square pipe in Grade 202, as per drawing. No. 1

54 7 Kitchen Hood: Fabricating of Kitchen Steel Hood of Size 72”x36”x20” with filter along with ducting pipe in GI sheet and exhaust fan for out-let to remove particles such as dust, dirt, smoke etc. The out-let pipe will be hanged with fast nut in the ceiling No. 2

MR-5 Sculpture In Central Courtyard

55 Design, detailing, and fabrication of metal sculpture (custom design as per approved concept by Architect and Engineer in Charge) Must meet corrosion resistance and aesthetic standards. Finish as per artistic intent and environmental exposure. RCC pedestal or steel base with anchoring bolts. Artistic enhancement and nighttime visibility. Material Grade: Use corrosion-resistant metals like SS 304/316 or Corten steel depending on climate and exposure. • Finish Quality: Surface finish must be uniform, free from blemishes, and aligned with the artistic vision. • Structural Integrity: Must withstand wind loads, seismic activity (if applicable), and vandalism. • Installation Safety: All lifting and fixing must comply with local safety codes and engineering standards. • Documentation: Include soft drawings, artist’s concept approval, and structural calculations. Num 11

MR-6 Mural- On Toilet Block Building

57 Providing and installing a high-relief mural designed in an abstract realism style, approximately measuring 16 meters by 5 meters. The artwork is crafted from durable sand and cement, with a surface layering thickness ranging from approximately 2 inches to 6 inches as needed. It comes with a 12-month material warranty from our side. The surface will feature a clear Western color, complemented by a two-tone color palette. To enhance the richness and depth of the colors, a matte nish pigment will be applied, ensuring vibrant, long-lasting hues that add a distinctive character to the mural. Sqm 80

MR-7 Super Tree

59 Design, detailing, and fabrication of metal super tree (custom design as per approved concept by Architect and Engineer in Charge).Must meet corrosion resistance and aesthetic standards. Finish as per artistic intent and environmental exposure. RCC pedestal or steel base with anchoring bolts. Artistic enhancement and night time visibility. General Description: 1- Structure Type: Decorative metal super tree, inspired by vertical garden or sculptural installations. 2- Purpose: Aesthetic landmark with integrated lighting for public spaces, parks, or commercial zones. 3- Height Range: Typically 6–15 meters, depending on design intent. 4- Finish: Powder-coated or weather-resistant paint in specified color Num 8

Main Frame: 1- Mild steel or galvanized steel sections (IS 2062 grade or equivalent). 2- Hollow circular/square pipes for trunk and branches. 3- MS plate (minimum 20 mm thick) with anchor bolts for foundation. Lighting Fixtures: 1- LED spotlights, strip light, RGB floodlights, Pixel dot light on metal structure as per architectural design and concept. 2- IP65 or higher rating for outdoor use. 3- Smart control options (DMX, remote, or app-based).

Fabrication & Installation 1- Welding: MIG/TIG welding with proper finishing and grinding. 2- Surface Treatment: 3- Sandblasting before painting. 4- Zinc primer + top coat (minimum 100 microns total). Foundation: 1- RCC pedestal with anchor bolts. 2- M25 grade concrete with steel reinforcement. Electrical Works 1- Cabling: 2- Armoured copper cables (1.5–4 sq mm depending on load). 3- Concealed conduits within the structure. 4- Control Panel: 5- Weatherproof enclosure. 6- Timer or sensor-based automation. 7- Earthing: 8- GI earth rod with proper connections.

Lighting Design 1- Type: Ambient + accent lighting. 2- Color Options: Static white or programmable RGB. 3- Mounting: Recessed or surface-mounted depending on fixture type. 4- Power Load: Estimated 500W–1500W per tree depending on size and lighting density.

60 Supplying, Providing, and Fixing, a musical fountain—also known as a dancing fountain or fairy fountain—is a choreographed water feature that synchronizes water movements, lighting effects, and music to produce captivating shows. These fountains are often installed in public parks, malls, resorts, and cultural venues. as per Architects and Engineer in Charge. How It Works 1- Water Jets: Controlled by high-pressure pumps and valves to shoot water in patterns. 2- Lighting: LED or RGB lights illuminate the water, often changing color and intensity. 3- Music Synchronization: A computerized control system times water and light effects to match the rhythm and mood of the music. 4- Automation: Some advanced systems can respond to live music in real-time, creating spontaneous displays. Num 1

MR-9 Illuminated 3D text on external façade

61 YOU ARE AT SONPUR MELA (900MM HIGH) Providing,fixing & installation of Illuminated 3D text on external façade having 3mm white transparent Acrylic Letters on sides & black acrylic on front With LED 170 per Running Inch Each Alphabet 18

PART-B PLUMBING NS ITEMS

63 NS-1 Providing Supply of Grape Supporting Bars, 12 mm diameter, 2.4 m long, fabricated from mild steel with U-bend at ends for wire holding, surface painted (2 coats red oxide + 1 coat enamel), suitable for trellis grape farming system. Nos 10

64 NS-2 Providing Tixing Testing Commissioning Delta Brass Robe Hook | Coat Hook | Bathroom Accessories (Chrome Finish, Wall Mounted) testing of joints complete as per direction of Engineer in Charge. Nos 21

65 NS-3 Providing Supply and place PARASNATH brand stainless steel perforated dustbin, capacity 10–15 liters, made from high-grade SS 202/304 stainless steel with a matt finish. Dustbin shall have a perforated body design for ventilation, be corrosion-resistant, durable, and suitable for indoor use in offices, institutions, or commercial spaces. Approximate dimensions: 250mm diameter x 300mm height. Smooth edges and anti-skid base. Sample to be approved prior to supply. Nos 25

66 NS-4 Providing & fixing of approved coloured verticle type hot water 25 ltr geysers. The inner container shall be made of copper sleeve with PUF insulation between inner and outer container, element pipe and heating element, pressure cum vaccume release, thermostat and thermal cutout arrangements and fusible plug. The outer container shall be of powder coated finish with all other accessories including fixing brackets complete as required. Nos 4

67 NS-5 Supplying and fixing of shower diverter made of brass/chrome-plated, suitable for concealed installation, 2-way/3-way function, including necessary fittings, cutting, threading, and making connections complete in all respects as per direction of Engineer-in-Charge. Nos 10

68 NS-6 Supply Installation, commissioning and testing of single phase 2H.P. submersible pump set having discharging capacity 3 Ips at a total head of 30 meter (approx) of KSBj Kirloskar or equivalent make with all accessories & fittings etc including loading unloading and transportation of the pump set to the work site with all required labour, materials, tools and tackles installation, testing & (i) 50 mm dia x 3 mtrs long medium classG.I column pipe both end thread and one end socketed- 6 (six) nos (ii) lx3x2,5 mm' flat copper conductor submersible cable -40 (forty) mtrs. (iii) 50 mm dia union socketlIonel no. (iv) 65 mm dia x 250 mm long G.!. nipple- 1(one) no. (v) 50 mm dia G.I Elbow-l(One) no. (vi) 50 mm dia M.S, clamps-2(Two) Pairs. (vii) 50 mmx 250 mm long G.I nipple- lIOnel no. (viii) Tube well cap for T/WelllIonel no. (ix) 50 ":l~ia x 65 mm dia 2 No

Supply Installation, commissioning and testing of floor mounted outdoor type loT feeder pillar single phase starter controll pannel operated on 220V, 3 phase, 50 cis for 3 HP Submersible pump set made of MS sheet (minimum 2 mm thick) duly spray power coated painting with following accessories made of M.Ssheet ( minimum 2mm thick) duly spray powder coated painting with following accessories (i) 90-220 V range single phase7. 5 KVA automatic voltage stabilizer make- Sen & Pandit/ Vertex/ISI marked If any. 1No. (ii) Suitable single phase starter control panelfor above motor of BCH /L&T make-1 (one) no. 2 No

Supplying & fitting 2.5 mm' copper service cable from power point from nearest source up-to I pumping station 150 m

Providing all materials and labour required lor doing earthing station with G.I earth pipe of 40 mm dia x 4.5 mtrs 20fts. long G.I pipe including accessories excavation of earth , providing masonry enclosure with Coverplate having locking arrangementand watering pipe etc.with salt, charcoal,etc.as per IE & IS specification 2 No

PART-C ELECTRICAL NS ITEMS

NS-1 NS ITEMS LIGHTING

69 SITC of Step light with 3W,h aving IP65 Protection Rating, CCT: 3000K / 5600K, Aluminum Alloy Material, Body Color: Telegrey. Input Voltage: AC100-230V Each 140

70 NS-2 SITC of 9W Mono color Spike light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Spike for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV- 4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Each 115

71 NS-3 SITC of 9W Mono color Spot light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Each 130

72 NS-4 SITC of high quality inground light with a power rating of 12W and CCT —3000K - 5600K for crisp articulation—offering versatility across architectural applications. Beam Angle : 30°, designed to minimize hot spots and ensure smooth light distribution. The fixture’s body combines stainless steel and aluminium, achieving a balance of corrosion resistance and thermal efficiency. Rated IP67, it guarantees complete protection against dust ingress, making it ideal for high-exposure environments including driveways, plazas. The unit supports wide-range Each 70

73 NS-5 SITC of 10W COB Downlight - Metal Body, CCT: 3000K, Power Input: AC 140-240V, 50Hz, IP Rating: IP65. Each 140

74 NS-6 SITC of high quality long through mono color Linear wash light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 36W, CCT : 1800K/3000K/4000K/6000K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK07, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, IP66, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP67 connector having the length >300mm. Each 22

75 NS-7 SITC of 9W Mono color Spike light, Protection Rating : IP66, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" and having CE certification against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Spike for fixing the lights. Power consumption : 9W, CCT : 1800/3000/4000/6000K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : AC110-230V, Surge Protection : Inbuilt surge protection 2KV- 4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK05, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK05, IP66, from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Each 40

76 NS-7.1 SITC of UNILinear Flex is IP68 cove lighting with reliable performance and excellently water-proof, anti-dust LED strips, CCT : 1100LM 3000K L5000, (as per the design approval) with professional design for vivid colors. or equivalent with the engineer or 3rd party testing laboratory approval. MTR 50

NS-8 NS ITEMS DG SETS

Designing, Supply & erection of DG set of capacity given below with noise controlled devices acoustic of suitable rating, testing and commissioning of diesel generating set, radiator cooled, 3 phase, 4 wire, 50 cycles 415 +(-)1% volts AC alternator coupled directly through a set of flexible coupling on a common MS fabricated base frame with diesel engine complete with suitable size incoming cable from generator to change over/AMF panel, making 2nd incoming cable connection from transformer, outgoing cable connection from changeover/ standard panel, making second incoming cable connection from transformer, outgoing cable connection from changeover / STD panel to incomer of motor starter panel, fenced enclosure with platform for DG sets complete as per following detailed scope and specifications and directions of Engineer-in-charge.

The rating should be at 1500 RPM. a) Diesel Engine b) Alternator c) Battery 24 v. d) Base Plate. e) suitable sq mm suitable core copper cable upto 40 metres. f) Tools, standard panel g) Metering set 415 VAC-1 set (Amp. meter, Volt Meter, ASS, VSS, Phase Indicator,control fuse, frequency meter, CT's) h) Metering set 60/5A/11 OV (Amp. Meter, Volt Meter) i) Overload protection for DC-1 No. j) Battery Charger 24V DC k)Copper bus bar of suitable size I) KWH meter 96 sqmm size m) Starting fuse button and key switch9on/off) n) Indicating lamps for low lubricated oil pressure, high coolant temperature, set running, load on, De control and other required accessories complete in all respects to the satisfaction of Engineer-in-charge

77 200KVA DG SET Each 1

NS-9 ELECTRICAL PANEL

Design, manufacture supply, installation, testing and commissioning of the following extensible cubicle type indoor mounting, dead front, fully compartmentalised with hinged lockable detachable front & back openable, dust and vermin proof, floor mounting sheet steel clad switchboard fabricated out of 2 mm thick CRCA powder coated sheet steel suitable for use at 415 volts 3 phase 4 wire 50 cycle system and to withstand a symmetrical fault level as specified at 415 volts. Panels shall be fabricated in easily transportable sections, length, height, depth etc. to match with site condition. All incomer breaker and Bus Couplers shall be interlocked electrically as shown in SLD and specifications.

Note: The following provisions shall be required to be made in the switchboard as detailed below:

a) The Switchboards shall have provision to accommodate all cables from the bottom /top as required.

b) All live accessible parts shall be shrouded with 1mm thick polycarbonate/3 mm thick FRP sheet and all equipment shall be finger touch proof. The busbar insulation shall be with heat shrinkable sleeves according to the colour code. SMC shrouds and busbar supports shall be used.

c) Galvanised hardware with zinc passivation shall be used in fabrication of Switchboards.

d) All rear door of Main LT Panel shall be Almirah type with lockable arrangement.

e) Space heater shall be provided with thermostat with 6A MCB as backup protection in each section of Main LT Panel & controlled with 20 A DP MCB, 10 KA.

f) Provision of one 6/16 amp socket & compartment lighting for each vertical section of main LT Panel.

g) The panel shall display Main Incomers Bus Couplers of Main LT Panel. This line diagram shall be made from luminous non fading materials to glow in dark and each breaker legend shall be provided with bi-colour LED lights to show the Phase indication Lamp & ON/OFF status of the respective feeder (Incomers / Bus couplers)

h) All control & power wiring shall be broughtout upto the cable alley in the terminal blocks. 10% extra terminals shall be supplied along with Panel.

i) An approval shall be taken for each panel before manufacturing.

j) Suitable Aluminium earth bus to be provided throughout the length of Switchboards.

k) All indication lamps / illuminated push buttons shall be LED type.

l) 2A SP MCBs shall be used as backup protections.

m) Coil of all motor starters shall be fed from 440 V / 230 V Control Transformer.

n) All incomer meters of Main LT Panel shall be multifunction & should have all the electrical parameters like, Voltage, Ampere, KW, KVAR, KWH, PF, Frequency etc. with communication port RS-485.

o) All feeders with KWHr meter will be Electronic Dual Reading KWHr meter alongwith appropriate CT's and 1 sq. mm control wiring from each KWHr meter for RS-485 communication till DCU's compartment.

p) Provision for providing 230V AC supply for Dual KWHr metering when any or all DG are in operation

q) One separate compartment of minimum size 400 x 900 mm for power management system of D.C.U.'s with control wiring as per following specification and control wiring scheme. Control wiring shall be looped from each energy meter till DCU's compartment for sending DCU register change command from data connectivity.

r) All CT & PT's shall be cast resin type. Class - 3 CT shall be provided up to 100 amp and above that the CT shall be Class - 1.

s) Zone selective Interlocking to be hardwired between incoming & outgoing ACB of main LT Panel.

t) All incomer ACBs of Main LT Panel shall be with microprocessor based releases (O/C, S/C & E/F), display of current/voltage and communication port RS-485, however ACB Incomers in other distribution panel and outgoing of Main LT Panel shall be with standard releases.( Ics=100%Icu=Icw )

u) All Main LT Panel outgoing ACB shall be with inbuilt earth fault release with CT & MCCB shall be with earth fault module with associated neutral CT for feeder protection, for TP feeders & E/F release for FP feeders.

v) All MCCB shall be provided with Rotary handle, door interlocked & lockable in off position of MCCB.

w) All Main LT Panel outgoing MCCBs shall be with microprocessor based releases, line load reversibility, Ics = 100% Icu.

x) Rating of Neutral bus-bar shall be 50% of phase-bus bar

y) All MCB to be C Curve type

z) Micro PLC for auto load management & interlocking as per logic specified.

i) 800amps 50 kA 440 volt FP MCCB with overcurrent and short circuit and earth fault module, with heavy duty solid detachable neutral link

Metering for incoming:

a) 3 nos 800/5A Class 1, 15 VA Burden CT's for metering & 1 nos associated Neutral CT for earth fault module.

b) Digital flush type class -1.0 accuracy multifunction meter with RS-485 communication port for measurement of THD, KVARH KW, KWH, KVAR, PF, V, A, Hz, equivalent to EM6400 NG, with 3 Nos. current transformers of required ratio, 15 VA Class 1.0

c) Phase indication Lamp & ON/OFF indicating lamps with 3X2A SP MCB as backup protection.

TPN Aluminium busbars aluminium three phase and neutral busbars rated at 1000 amps, 50 KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Current density of Bus Bar to be 1.0 sq.mm / amp.

A 10 Nos. 100 Amp 4P MCCB With breaking capacity of 25KA

B 2 Nos. 63 Amp 4P MCCB With breaking capacity of 25KA

C 6 Nos. 63 Amp 4P MCB With breaking capacity of 10KA

C 1 Nos. 63 Amp DP MCB With breaking capacity of 10KA

78 MAIN LT PANEL complete as above required. Each 1

NS-10 METER BOARD PANEL (BLOCK AREA AREA)

i) 100 amps 25 kA 440 volt FP MCCB with overcurrent and short circuit and earth fault module, with heavy duty solid detachable neutral link

Metering for incoming:

a) 3 nos 100/5A Class 1, 15 VA Burden CT's for metering & 1 nos associated Neutral CT for earth fault module.

b) Digital flush type class -1.0 accuracy multifunction meter with RS-485 communication port for measurement of THD, KVARH KW, KWH, KVAR, PF, V, A, Hz, equivalent to EM6400 NG, with 3 Nos. current transformers of required ratio, 15 VA Class 1.0

c) Phase indication Lamp & ON/OFF indicating lamps with 3X2A SP MCB as backup protection.

TPN Aluminium busbars aluminium three phase and neutral busbars rated at 150 amps, 25KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Current density of Bus Bar to be 1.0 sq.mm / amp.

A 20 Nos. 32 Amp DP MCB With breaking capacity of 10KA

B 4 Nos. 63 Amp 4P MCB With breaking capacity of 10KA

79 SUB LT PANEL complete as above required. Each 8

NS-11 Feeder Pillar

Design, fabrication, assembling, wiring and supply, installation, testing and commissioning of Distribution Panels fabricated out of (load bearing member of 2mm and non load bearing member 1.6 mm thick) GI sheet steel in cubicle compartmentised modular 3b construction, free standing floor mounted with bottom cable entry,300 mm MS painted stand and standing covering from 3 sides, IP 55 double door with canopy ,dust and vermin proof with reinforcement of suitable size angle iron, channel, `T’ sections and / or flats wherever necessary. 3 mm thick cable gland plates shall be provided at the bottom of the panels with appropriate stand etc. Panels shall be treated with all anticorrosive process before powder coating as per specifications and final approved shade. 2 Nos. earthing terminals shall be provided for all distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be used in fabrication of panels.(Make AAA Switchgear, Indiatech panel, Neptune india)

Feeder Pillar (For External Landscape lighting) IP 55 for outdoor Protection

63 Amps 4 pole MCCB

100 Amps TPN Aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set

63 Amps two pole MCB incomer with 63 Amps DP contactor 0-24 hours timer auto / manual and outgoings including 6 No. 10/16/20 Amps SP MCB with separate neutral link of each phase- 1 set (50%)

40 Amps DP MCB with 32 amp industrial sockets - 2 sets

63 Amps 4 Pole MCB - 2 set

80 Feeder Pillar for external / landscape lighting as described above Each 1

NS -12 NS ITEMS C.C.T.V.SYSTEM

(Make- Honeywell, Godrej, Samsung as per approval of EIC)

81 A IP Varifocal Dome camera: Design, Supply, installation, testing and commissioning of 4MP BULLET IP CAMERA.,minimum 1 year warranty Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 45

82 B Supply , Installation , Testing and commissioning of 16 Channel NVR (Network Vedio Recorder) Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 3

83 C Supply, installation, testing & commissioning of 43" inches LED screen suitable for showing out puts from NVRs on a single screen (24x7) complete in all respect complete as required. Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 2

84 D Supply, laying and termination of CAT6 cable in existing conduits/ raceway/ cable tray for both video and control. MTR 2000

85 E Supply, installation, testing & commissioning of 4 TB Survillance HDD for camera recording.(24*7 ) Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 3

86 F Supply, installation, testing & commissioning of 8 PORT POE GIGA SWITCH Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 6

87 G Supply, installation, testing & commissioning of RJ 45 CONNECTOR Make: Hikvision / Bosch / Pelco / Honeywell / GVD Each 50

NS-13 11kV / 415V PACKAGED SUBSTATION: HT SIDE: 4P VCB TRANSFORMER: OIL TYPE LT SIDE: 4P MCCB

Outdoor type Package Substation with facility for internal lighting, earthing, padlocks etc. Connection between RMU & Transformer will be by 3 nos. 1C x 95 Sqmm. Aluminium conductor XLPE cable and connections from Transformer to LT ACB / MCCB will be by Aluminium bus bar connections. Cable termination kits for RMU shall be in the scope of supply (within the enclosure).

Package Substation will have the following equipments:

1 No. 630A ACB as Outgoing to Transformer : 1 No.

IDMT RELAY– Self Powered, Microprocessor based numerical 3 Nos. O/C +1 No. E/F (with inbuilt tripping mechanism - mytop or equivalent) with LCD display - ON/OFF/Trip..

Dual core CT’s for protection & metering, cast resin type and of suitable ratio & burden, (Class-1 for metering & class 5P10 for protection).

Cast Resin PT's of 11000V/√3/110V/√3 ratio of Class-1 accuracy & of suitable burden with HV fuse on primary side & MCB / MPCB on secondary side.

The Ring Switches and Tee-Off Circuit Breaker are provided with Integrated Earthing Switches with Making Capacity.

Live cable indicator for ring switches.

Shunt trip coil rated for 24V DC

SF6 Gas pressure indicator.

Padlocking facility.

Mechanical indications for breaker ON / OFF / TRIP

Communicable type multifunction meter with MDI (A, V, Hz, KW, KWH, KVA, KVAH, KVAR, KVARH)

Ammeter with selector switch.

Voltmeter with selector switch.

Line Voltage presence indicator.

Transformer Auxiliary Relay with alarm & trip contacts for:

Winding temperature

Oil Temperature

Emergency 'OFF' Push buttons

Manual ON/OFF Push buttons

12 Windows annunciator. (Hooter @ Remote location i.e. inside LT Panel room) with necessary cabling.

Trip circuit healthy indication

230V AC / 24V DC Power Pack of suitable capacity

CFL based bulk head light fixture with limit switch in the HT Compartment.

11KV/415V, 400.kVA three phase, Dyn11, tapping + 15% to - 15% in steps of 2.5% On load Tap changer (OLTC), CU/CU Winding Hermetically Sealed without gas cushion ONAN Transformer with standard accessories :1 No.

Transformers shall be as per IS : 1180 ,Level 2 ( Star 1 rated)

Door interlock to trip HT breaker on opening of transformer compartment door (only in transformer's with off circuit tap changer).

1 No. 4pole 800A / 50kA manually operated fixed type *MCCB with microprocessor based O/L, S/C & E/F releases. Ics = Icu for the breaker.

LT side metering shall include: 1set of LT cast resin CT's, PT’s & Communicable type VAF meter, LED TYPE R Y B indication lamps, ON/OFF/ Trip indication lamps, control MCB's / MPCB’s of required fault withstand and control wiring etc. at the LT side incomer breaker.

CFL based bulk head light fixture with limit switch in the LT Compartment.

88 Packaged Substation as described above. No 1

SOLAR PV SYSTEM

NS-14 Supply Installation testing commissioning of Solar Photovoltaic grid connected roof top Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- (a) Solar Photovoltaic Module manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. (b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz plus /- 2.5 Hz, output voltage suitable to generate AC (c) Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degrees C. The PCU shall adjust the voltage and frequency level to suit grid frequency (d) Data Monitoring System complete with accessories. (e) Fixing of Array junction box and Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. (f) Lightning and surge voltage protection. (g) Connections and Interconnections by supplying and fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power

89 1 Above 100 kWp and up to 500 Kwp KWp 200

PART-D FIRE FIGHTING NS ITEMS

FIRE EXTINGUISHERS

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity.

90 NS-1 ABC powder type fire extinguisher of 6 Kgs. Capacity, with initial filling (Mono Ammonium Phospate Powder) in brand new cylinder with powder coated finish, Stored Pressur type, Pressure Gauge, Controllable discharge mechanism with Hose & Nozzle , confirming to IS:15683:2008. Nos. 15

91 NS-2 Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, Co2 gas as per IS 15222 with controll discharge mechanism fitted with Hose & Horn applicable on Class B fire rating 21B confirming to IS: 15683:2008. CO2 Cylinder as per IS 7285 with ISI mark. Nos. 15

PART-E HVAC NS ITEMS

AIR CONDITIONING WORK

VARIABLE REFRIGERANT VOLUME/ FLOW SYSTEM

Supply, testing and commisioning of Aircooled inverter based modular type VRF/ VRV system using R-410A refrigerant. This should complete with interconnecting copper refrigerant piping with insulation, copper power cabling and control wiring in PVC conduit between indoor and outdoor (given in separate head). Power supply to suggested ODU shall be given at one point and further distribution shall be in scope of contractor including panel and cabling. This specifications is applied for all items wherever it is required.

MK-1 OUTDOOR UNITS

Supply, unloading, storing, shifting, installing, testing and commissioning of Modulating VRF/VRV Outdoor Unit (Cooling Only Type) suitable for 415V/ 3Ph/ 50Hz AC. Supply including 100% Inverter Based Scroll Compressors with first charge of R-410A refrigerant with DC Inverter, High efficiency heat transfer cooling coil suitable for environment friendly R-410A refrigerant, Air cooled propeller type condensor fan with DC motor drive, interconnecting piping, suction line insulation, microprocessor control panel suitable for automatic operation, High speed calculation inverter control, MS frame with rubber pad etc. all complete as per specifications, drawings and direction of Engineer In charge.

The unit capacities shall be considered after taking deration into account due to copper piping lengths & ambient conditions. The Unit shall be capable of operating upto 52 °C ambient temperature. Test certificates to this effect must be provided prior to supplying equipment at site. The card replacement shall be done without any extra cost if it fails to perform under indicated voltage range and fluctuations.

VRV ODU's shall be capable of operating in the following range: i) For Cooling : (-)5 °C to 52 °C

Note- Nominal capacity suitable for cooling requirements. Combination above capacities as per OEM for economical & efficient combination.

MK-2 4 WAY CASSETTE UNIT

Supply, unloading, storing, shifting, installing, testing and commissioning of VRV/VRF type 4-way cassette Indoor units. The unit shall include pre-filter, fan section and DX-coil section. The housing of the unit shall be powder coated galvanized steel. The body shall be light in weight. Unit shall have an external attractive panel for supply and return air. The condensate drain of the units to be done with proper insulation & fittings to be terminated to the main drain line as per the layout plan. All indoor AC units shall be provided with drain pumps which shall be subjected to brand selected.

93 2.0 TR Nos 1

94 2.6 TR Nos 4

95 3.2 TR Nos 2

96 4.0 TR Nos 2

MK-3 HI WALL UNIT

Supply, unloading, storing, shifting, installing, testing and commissioning of VRV/VRF type wall mountedhi-wall units. The unit shall include pre-filter, fan section and DX-coil section. The housing of the unit shall be powder coated galvanized steel. The body shall be light in weight. Unit shall have an external attractive panel. The condensate drain of the units to be done with proper insulation & fittings to be terminated to the main drain line as per the layout plan.

97 1.5 TR Nos 2

MK-4 INLINE FAN

Supply, unloading, storing, shifting, installing, testing and commissioning of circular Inline fan shall be complete with non-stalling backward curved centrifugal Impeller, GSS Casing, direct driven Single phase(230 V±10%, 50 Hz.) external rotor Motor with IP44 Protection & Class B Insulation with speed regulator & all accessories as required. Noise Level shall not exceed 60 dB (A) at 3 meters at room condition.

98 Capacity: 400 CFM External Static Pressure: 12 mm WC Nos 1

MK-5 COPPER REFRIGERANT PIPING

Supply, installation, testing and commissioning of refrigerant pipe work with (19mm/13mm thick) closed cell elastomeric nitrile rubber/XLPE tubular insulation between each set of indoor & outdoor units as per specification, all piping inside the room shall be properly supported with GI slotted cable trays & all external piping shall run in covered cable tray. UV coat protection to be applied on the exposed elastomeric insulation provided on pipes. (Cost to be included in quoted price)

99 41.8 mm O.D. (with 19mm insulation) RM 25

10 34.9 mm O.D. (with 19mm insulation) RM 6

101 28.6 mm O.D. (with 19mm insulation) RM 10

102 22.2 mm O.D. (with 19mm insulation) RM 6

103 19.1 mm O.D. (with 19mm insulation) RM 55

104 15.9 mm O.D. (with 19mm insulation) RM 35

105 12.7 mm O.D. (with 13mm insulation) RM 10

106 9.5 mm O.D. (with 13mm insulation) RM 65

107 Y Joints Pair 11

MK-6 UPVC CONDENSATE DRAIN PIPING

Supply, installation, testing and commissioning of 6 Kg/m3 density UPVC pipe (heavy duty) with 9mm thick nitrile rubber insulation (tube insulation) with protective coating as per the approved shop drawings and specifications.

108 40mm dia. RM 15

109 32mm dia. RM 30

110 25mm dia. RM 20

MK-7 CONTROL & TRANSMISSION WIRING

Supply, installation, testing & commissioning of copper flexible control cum transmission wiring of 2core x 1.5mm2 in suitable conduits between indoor and outdoor units. Charges of conduits are included.

111 2 Core x 1.5 sqmm copper RM 120