Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹40.0 LAccepted-AOC NEAR RANGE OFFICE CHOUBYANA TALBEHAT DISTT LALITPUR UP | TALBEHAT | LALITPUR | UP | L1 | Accepted-AOC being L1 bidder | |
| 2 | L2₹43.3 L+₹2.4 L (5.86%)Rejected-Finance 05 BABA PALACE MUSRIGHARARI JANDAHA ROAD MUSRIGHARARI SAMASTIPUR BIHAR 848101 | SAMASTIPUR | BIHAR | 848101 | L2 | Rejected-Finance not become lowest bidder | |
| 3 | L3₹44.1 L+₹3.2 L (7.91%)Rejected-Finance | L3 | Rejected-Finance not become lowest bidder | |
| 4 | L4₹44.6 L+₹3.7 L (9.09%)Rejected-Finance 792 2 A CIVIL LINES NEAR BABULAL MILL GWALIOR ROAD JHANSI 284001 | JHANSI | JHANSI | UTTAR PRADESH | 284001 | L4 | Rejected-Finance not become lowest bidder | |
| 5 | L5₹46.8 L+₹5.9 L (14.3%)Rejected-Finance C 204 NANGLI EXTN NEW DELHI | WEST | DELHI | 110043 | L5 | Rejected-Finance not become lowest bidder |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
6 Jun 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Major Sunny Kumar Attri
Garrison Engineer Jhansi
COMPREHENSIVE REPAIR TO CERTAIN MD/OTM ACCN FOR ZONE B UNDER AGE B/R-II AT GE JHANSI
2023_MES_594050_1
GE/JHA/TOK/40 OF 2023-24
Open Tender
Civil Works
Item Rate
180 days
GE Jhansi
As per NIT and Tender documents
9 documents required · 9 mandatory
₹500
Yes
GE Jhansi
₹90,000
Yes
14 Jul 2023
9 May 2023
8 Jun 2023
9 May 2023
6 Jun 2023
23 May 2023
9 May 2023 - 16 May 2023
Amount
Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.
Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.
M&L for Non skid ceramic colored tiles of size 300x300mm, 7 to 8 mm thick (square / rectangular) as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.
M&L for joint free, Vitrified Ceramic tiles of size 600x600mm, 10 mm thick (square/rectangular), in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.
All as per item No. 4 here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering in CM 1:4, complete all as specified and directed.
M&L for ceramic colour tiles in vertical surface of size 450 X 300 x 7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed.
M&L 20 mm thick granite slab, tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed.
M&L for factory made PU coated, chequered cement concrete tiles of any colour 30 cm x 30cm x 20 to 22 mm thick, set & jointed and pointed in neat cement slurry mixed with grey cement and pigments, laid over and including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.
Dismantling of wall / ceiling boards (fiber, pulp, insulation etc) / insulation boards /slabs/blankets of any thickness including cover fillets ridges etc, complete all as specified and directed.
S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.
Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 5 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.00 sqm) comprising of uPVC multi chambered rame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (stainless steel butt hinges and necessary S S screws, 6 mm Glass or wiremesh incl in this item) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in epth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
Dismantling boarding, cupborad any description, fixed in any position complete all as specified and directed.
S&F 18mm thick prelaminated WPC, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cup board shelves/shutter or similar work inclding dismantling of old board in any position, complete all as specified and directed.
S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed
Demolition of brick work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed.
M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.
M&L for half brick thick wall with fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.
Taking down cement plaster on brick or stone wall including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.
M&L for 15 mm thick rendering in CM (1:4) on fair/other than fair faces of brick work finished even and fair complete all as specified and directed.
M&L for 15 mm thick rendering in CM (1:6) on fair/other than fair faces of brick work finished even and fair complete all as specified and directed.
M&L for preparation of new plastered surface and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.
M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.
M&L for preparation of new plastered surface and applying three coats of white wash on new plastered wall surface, complete all as specified and as directed.
M&L for writing or repainting letters or figures (Block, Roman, Italic, Indian) exc 15.0 cm but not exc 30 cm in height and line of letters or figures not exc 2.0 cm wide for Bldg No / Name and similar works etc with two coat of synthetic enamel paint, complete all as specified and directed.
Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.
All as per item No. 25 here-in-above but not exc 1.5 sqm each
Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.
Taking down shutters of any description exceeding 01 Sqm and not exc 02 Sqm each, complete all as specified and directed.
S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws incl in this item)
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners incl in this item of required dia and length complete as per direction of Engineer-in-Charge.
S&F of 150mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.
S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed
S&F of 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed with screws, complete all as specified and directed.
S&F of 150mm long mild steel pressed handles, oval type, stove enamelled black and fixed with screws, complete all as specified and directed.
S&F of 250mm long mild steel, sliding door bolt clip and bolt type, stove enamelled black, with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts, complete all as specified and directed.
S&F of aluminium alloy anodized sliding door bolt 200mm length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed.
S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.
S&F of 150mm aluminum handle cast type anodized complete all specified and directed.
S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed
S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.
M&L for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.
M&L for stainless steel rod 15mm dia steel pipe cutting into length as required at site with and incl SS end brackets, fixed in cupboard and similar works, complete all as specified and directed.
S&F of 35mm thick factory made modular designer flush doors, solid core construction, with block board core and prelamination on both sides, complete all as specified and directed.
M&L for second class hard wood. Plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.
M&L for 35mm thick second class hard wood glazed & skeleton shutter for doors (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (with sash bars) edges of framing plain, chamfered sash bar, or rounded, fitted without & mitred beads for securing glass etc, conforming to IS-1003 Part-I & II; size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) complete all as specified and directed.
M&L for 30mm thick second class hard wood glazed & skeleton shutter for doors (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (with sash bars) edges of framing plain, chamfered sash bar, or rounded, fitted without & mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section–8, clause 8.24(b) and conforming to IS-1003 Part-I & II, complete all as specified.
M&L for cement concrete 1:2:4 type B1 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, bond stones, bed plates for hold fast and the like including weathering, slightly rounded or chamfered angles and throating, , complete all as specified and directed.
M&L for mild steel angles, bars, flats etc, as in hold fasts, pipe clamps, plain angle cleats for securing purlins, supports for stiffening of fencing, wall ties and similar small articles confirming to Fe-290 Gde E-165, complete all as specified and directed.
M&L for mild steel section as in door/windows chowkhats frame of steel gate of grade Fe-290 Gde E-165 including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.
Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as directed.
S&F of 3 mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as directed.
S&F of 3 mm thick sheet glass ordinary quality and glazing type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as directed.
S&F in replacement of stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.
S&F of stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.
Taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern, complete all as specified and directed.
S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.
S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.
S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.
S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.
S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.
S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.
S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.
S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.
S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.
S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.
S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.
Taking down steel tubing with and incl connections, of 15 mm dia bore, complete all specified and directed.
Taking down steel tubing with and incl connections, of 20 mm dia bore, complete all specified and directed.
Supplying and laying of 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches or fixed to walls complete all as specified.
Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches or fixed to walls complete all as specified.
M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed.
S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.
S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.
S&F in replacement of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.
S&F 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.
S&F in replacement of stainless steel sink, 1.00 mm thick for kitchen with plug, with and incl 40mm dia CP waste coupling, waste pipe of 750mm long, washers, cantilever brackets, connecting union etc overall approx size 550 mm x 450 mm with approx bowl size of 500 mm x 375 mm x 200 mm etc, complete all as specified and directed.
S&F in replacement of stainless steel kitchen plate rack made out of imm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg, complete all as specified and as directed.
S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.
S&F in replacement of 3-in-1 wall mixer with provision for overhead Shower with 115mm long bend pipe on upperside, connecting legs & wall flanges made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.
S&F in replacement of Stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed.
S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swirl type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.
S&F in replacement of bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed.
S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed.
S&F in replacement of handshower (health faucet) with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.
S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all as specified and directed.
S&F in replacement of bottle trap 32 mm sizewith 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.
S&F SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all as specified and directed.
S&F in replacement of toilet paper roll holder with flap made of cast copper alloy, chromium plated, complete all as specified and directed.
S&F in replacement of towel rail 600 mm long and wall bracket made of cast copper alloy, chromium plated, complete all as specified and directed.
S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.
S&F in replacement of PVC made multipurpose cabinet with front openable door of overall size 350 x 450 mm, complete all as specified and directed.
S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as specified and directed.
S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.
S&F in replacement of waste coupling, chromium plated (half or full threaded), 32 mm dia size, complete all as specified and directed.
S&F in replacement of waste coupling, chromium plated (half or full threaded), 40 mm dia size, complete all as specified and directed.
S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as specified and directed.
S&F in replacement of plastic seat with cover for water closet, of existing colour, closed pattern with flat bottom with chromium plated hinging device, complete all as specified and directed.
S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.
S&F in replacement of 1st quality vitreous China white urinal flat back (Large size) with and incl CP waste coupling of suitable size, cast copper alloy CP spreader union with discharge pipe duly connected to auto closing angle cock, complete with necessary fittings, complete all as specified and directed.
S&F in replacement of 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as specified and directed.
S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as specified and directed.
S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.
M&L for preparation of newly steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed
M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over and including a coat of primer and layer of putty/filling material to get smooth & level finish, complete all as specified and directed.
Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed.
Dismantling timber scantling 40.0 sqcm and over in section in any position as in framed / unframed works such as roof purlins, rafters, fillets, ridges etc as in roof/ ceiling, complete all as specified and directed.
S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.
S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed.
M&L for structural steel Fe-410-W(Gde-E-250) quality A for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.
M&L for powder coated aluminium frame for doors, windows, ventilators with one or more rebates, fabricated out of powder coated aluminium hallow square or rectangular section of required size incl necessary joining cleats, fixing screws etc complete, having size of frame for doors 100mm x45mm x 3.18 mm thick; for window 104mm x 45mm x 3mm thick; for ventilators 59mm x 33mm x 2.5mm, complete all as specified and directed.
M&L for powder coated aluminium door shutters, aluminium section for top rail and styles 85mm x 45mm x 2.0mm thick; bottom rail 100mm x 45mm x 2mm thick and lock rail 100mm x 45mmx 2.0mm thick incl necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, powder coated aluminum hinges, powder coated aluminum snap beading, screws, etc, complete all as specified and directed.
S&F powder coated aluminium window shutter Sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.
M&L for powder coated aluminium wall partition, window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws etc, complete all as directed.
M&L for Anodised aluminium grill of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement
S&F of glass, tinted type, 5.5 mm thick, each panes not exc 0.5 sqm, suitable for aluminium window / Ventilators / door opening and similar work, complete all as specified and directed.
M&L for aluminium (Extruded section) body door closer, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 60 to 80 kg complete all as specified and as directed.
Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with ecessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.
M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.
M&L 40 mm thick plain cement concrete type B1 1:2:4 (using 20 mm graded stone agg) as in floor, finished even and smooth (without using extra cement), laid in panels using 4.0mm thick & 38mm wide glass strip, panels will be not more than 1.2 x 1.2 mtr in size, laid to slope 1:30, complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of 4mm thick & 38mm wide glass strip.
M&L for 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) in sub base, flooring, complete all as specified and directed.
M&L for factory made PU coated, machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of rubber moulded with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. Note : The cost of sand cushion and plastering to edges is included in quoted rate.
M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as spd and directed by engr in charge
M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a layer of (JK/Birla) wall care putty to get smooth and level finish, complete all as specified and directed
M/S BABA CONSTRUCTION
M/S AADI TRADERS
V K Engineers and Associates
S GOURAV PRAKASH ENTERPRISES
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .