REPAIR/MAINT TO COMPOUND WALL, FENCING, DRAIN, PATH, HARD STANDING, JOINERY, ALUMINIUM DOOR/WINDOW ETC IN MD/OTM ACCN IN ZONE A AND B AREA UNDER AGE (I) AYODHYA.

Amount

Taking down cement plaster from brick walls including raking out joints, hacking for key, scrubbing down with water to receive plaster removal of rubbish off the premises etc complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified.

M&L for preparing old decorated surfaces of walls and applying one coats of cement base paint complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar complete all as specified and as directed.

M&L for preparation of newly steel surface of any description over 10cm width or girth, not otherwise described applying two coats of synthetic enamel paint over a coat of red oxide primer over complete all as specified and directed.

M&L for brick work with Fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1 : 6 complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) posts embedded natural ground etc any section including taking out embedded portion and making good to distrubed ground complete all as specified and directed.

M&L for excavation in post holes each n.exc 0.50 Cum and getting out in soft/loose soil including returning, filling in and ramming earth etc and removing surplus soil to a distance n exc 50 M and making good surface complete all as specified and directed.

M&L for PCC 1:3:6 Type C2 (40 mm graded aggregate) as in foundation and mass concrete complete all as speicicfed and directed.

M&L for PCC 1:3:6 Type C1 (20 mm graded aggregate) in lintel upto 1.5m clear span,cill, steps,seismic and other similiar bands, plinth courses,string courses, laacing courses parapets and railings upto 60 cm in height, bed plates, copings, kerbs, etc. water troughs and the like includind weathering, slightly rounded or chamfered angles and throating as directed.

S&F hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Supplied only chain link MS galvanised fencing any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards including provission of binding wire complete all as specified and directed.

S&F mild steel screw bolts 5 to 10mm diameter of shank screw bolts (machine made) with hexagonal screw heads at one end & screwed the other or screwed both ends, each screwed endsto be fitted with washers & one hexagonal or square nuts, small end exe 5cm long complete all as specified and directed.

S&F galvanized 2 brand sheet barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straning and fixing to any type of standard rails strasing bolts including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed.

S&F round steel bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 Type B1 ( 20 mm graded aggregate) set in cement mortar 1:6 in window or door cills, lintels, steps coping, kneelers, pier caps, columns, post etc. and setting in mortar complete with joints to match complete all as specified and directed.

S&F TMT steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F TMT steel bars 6 to 8 mm dia, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia or with securing clips complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for machine pressed precast coloured concrete interlocking paver block any shape and size of 60mm thickness, M-35 Grade conforming to IS-15658-2006 with grey cement and pigment complete all specified and directed.

M&L for sand filling under floors, sand cushion or in foundations including watering and consolidation complete all as specified and directed.

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:6 on floors for laying floor finish complete all as specified and directed.

M&L for chequered cement concrete tiles set, joined and pointed in neat cement slurry in floors with grey cement and with grey cement and pigment complete all as specified and directed.

Dismantling floor, hearth or wall tiling including CM bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface such as ext wall cladding etc 350x250x 7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles and including 10mm thick rendering in CM 1:3 to receive wall tiles complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) as directed.

M&L for 75 mm thick PCC 1:3:6 Type C2 (40 mm graded aggregate) as in floors/Pavings/sub base etc complete all as specified and directed.

M&L for cement concrete 1:3:6 type c-2 (40 mm graded aggt) as in surface channel and drains complete all as specified and directed.

M&L for 100 mm thick PCC 1:2:4 Type B2 (40 mm graded aggregate) as in floors/Pavings etc and finish the surface without using extra cement and joint filled with bitumen and sand in 1:3 complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) posts embedded Cement concrete etc any section including taking out embedded portion and making good to distrubed ground complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour pvc 'C' channel having a PVC sheet strio of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails,lock rail and bottom rail on either side and as gap insert for top rail and bottom rail,Panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement supply anf fixing in the frame at site as per specification and drawing complete all as specified and directed.

M&L for preparation of new plaster of wall and applying two coats of oil bound distemper over chalk whiting primer on plaster surfaces complete all as specified and directed.

M&L for prepararion of new plastered surfaces of wall and applying two coats of weather coats over a coat of exterior grade primer complete all as specified and directed.

Taking down chowkhats or frame (with shuuter w/o taking of shutter from frame exc 1.5 sqmtr but n.exc 4 sq m each.) complete all as specified and directed.

S&F 35 mm thick, 2nd class hard teak wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamferd or rounded, fitted with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I Section 8 Clause 8.24(a), etc complete all as directed by Engineer-in-charge.

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commericial type on both sides complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of size 150 mm extruded section and fixed complete all as specified and directed.

S&F 100mm long stainless steel butt hings fixed to chowkats size complete all as specified and directed.

S&F 150mm long aluminium handle cast type anodised complete all as specified and directed.

S&F Aluminium alloy anodised sliding door bolt 250mm long with hasp, staple and fixing clip of sheet cast or extruded sections and fixing bolts complete all as specified and directed.

S&F for 300mm long MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 100mm long butt hinges medium grade cold rollled mild steel and fixed complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed.

S&F in repair for PVC coated mild steel curtain rod 25 mm dia complete all as specified and directed by Engineer-in-charge.

S&F powder coated fancy type mild steel bracket and PVC tops for PVC coated curtain rod complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F MS holdfast made up of FI 25mmx3mm conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

M&L for Treating small articles such as holdfast with Tar or coaL tar black paint complete all as specified and directed.

M&L for Sanding newly tarred of painted surface with clean sharp sand complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) as in bed blocks, similar work for embedding hold fast, etc. including necessary form work complete all as specified and directed.

S&F in reair 4mm thick plain glass and pin headed glass both type and glazing with rubber packing in square nexc 0.50 Sqm in each pane complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

M&L for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete as specified and directed.

S&F powder coated anodised aluminium window/ventilator shutter sliding type with styles, rails size 40mm x20mm, frame for chowkat size 30mm x 90mm, fixed glazing, all are made from aluminium anodised section including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size with and including 4mm thick frosted glass /tinned glass etc complete all as specified and directed. Note:- (i) Two Nos of track to be provided. (ii) In two tracks, shutter with frosted glass/tinned glass.. (iii) Thickness of aluminium section shall not be less than 1.00 mm)

S&F powder coated Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F for powder coated Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer on roof complete all as specified and directed.

Demolition of mud in roof any thickness including plastering and leeping (whether full thickness removed or only part there of complete all as specified and directed.

M&L for cement concrete type B-0, 1:2:4 (12.5 graded crushed stone aggregate) for roof padding complete all as specified.

M&L for 10mm thick plastering in cement morter 1:3 finished even and smooth w/o using extra cement with water proofing compound complete all as specified.Note:-WPC measured and paid seperately complete all as specified and directed.

M&L for preparation of newly plastering surface of roof including cleaning the surfaces by using wire brush/pressure hose and applying high performance polyurethane liquid membrane roof costing cold applied in two coats @ 1.5kg/sqm applied with spray/brush an elongation of 300% to 700% and tensile strength of not less than 3N/SQMM as per ASTM D412 and ASTM D2370,crack bridging ability of 3.5mm as per ASTM C 1305,shore a hardness of not less than 60 as ASTM D 2240.The items includes epoxy prime applied @ 0.15 kg/sqm and geotextiles of 40 GSM to be applied over first coat while first coat is still wet complete as per manufacture instruction and sound engineering practice complete all as specified and directed.

Saket Traders

ABC CONSTRUCTION CO