CERTAIN REPAIR TO DRAIN FENCING COMPOUND WALL IN MD ACCN UNDER AGE BR II AT GE FAIZABAD

Amount

Demolition of brick work built in Cement Mortar including all quions, arches, pillars, etc and pre cast concrete articles ,complete all as specified and as directed by Engr-in-charge.

M&L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as drains complete all as specified and directed by Engr-in-charge.

M & L for brick work With sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed by Engr-in-charge.

M & L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed by Engr-in-charge.

All as per item no 3 & 4 above but except brick (old size) any type complete all as specified and directed by Engr-in-charge.

Removing lime mortar , cement or cement lime mortar from and cleaning bricks, stacking for measurement including all extra handling and removal and disposing off rubbish , complete all as specified and as directed by Engr-in-charge.

M&L PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as surfaces channel and drains finish even and smooth using extra cement all as specified and as directed by Engr-in-charge.

Dismantling of fencing wire any type complete all as specified and directed.

S & F Galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire , staples or steel pins etc, all as specified and as directed by Engr-in-charge.

Fixing only Galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire , staples or steel pins etc all as specified and as directed by Engr-in-charge.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, laying of pipe and cables etc. but not exceeding 10 Sqm on plan including dressing/trimming sides and levelling/grading & ramming bottom of excavation and getting out in soft/loose soil all as specified and as directed by Engr-in-charge.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete, all as specified and directed by the Engr-in-charge.

M & L for 15 mm thick rendering in cement mortar (1:4) finished even and fair , all as specified and as directed by Engr-in-charge.

M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) in coping /benching and bed block of cattle trap or similar work rounded and chamfered on edges etc all as specified and as directed by Engr-in-charge.

Preparation of new plastered surfaces of wall and applying two coat of cement base paint over one coat of primer , complete all as specified and directed by Engr-in Charge .

M&L for preparing old decorated surfaces of wall including cleaing with broom and applying one coat of cement base paint all as specified and as directed by Engr-in-charge.

M&L 75 mm thick PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) finished even & smooth without using extra cement as in plinth protection / hardstanding complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed by the Engr-in-charge.

Removing surplus soil to a distance exc 50m but not exc 5.00 km and deposited where directed at a level not exceeding 1.50 m above the starting point complete all as specified and directed by the Engr-in-charge.

S&F chain link fencing of MS galvanised 3.15 mm dia including line wires of same dia , of mesh 75mmx75mm size to any type of standards , rails , straining bolts, etc. including provision of binding wire complete all as specified and directed by Engineer in charge.

M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamelled paint over one coat of red oxide Zinc chrome primer all as specified and as directed by Engr-in-charge.

M&L preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed by Engr-in-charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed by Engineer in charge.

M&L Framed work as in doors or gates of angle or other section with ornamental looks, gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engineer in charge. with Fe 410-W (Gde E-250).

M&L Mild steel works for hooks, pintle hinges, large hasp and staples, hand made sliding door bolts, clamps, holdfast , plate washer and similar works small articles confoming to Fe 290 (Gde E-165) complete all as specified and directed by Engineer in charge.

Demolition of cement concrete in ground floors and pavings n.exc. 15cm thick (below or above ground level) all as specified and as directed by Engr-in-charge.

M&L for 75 mm thick plain cement concrete 1:3:6 type D2 (using 40 mm graded stone aggregate) as in sub base, complete all as specified and as directed by Engr-in-charge.

M&L Chemical coated, factory made, chequered cement concrete designer tiles 300mm x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry over cement screed base laid and jointed with grey cement slurry with pigment to match the shade of tile, as in floors, complete all as specified and as directed by the Engr-in-charge.

M&L Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:6 for laying floor finishes, all as specified and as directed by Engr-in-charge.

M&L for Sand Cushion under interlocking paver & joint filled by sand complete all as specified and directed by Engr-in-charge.

S&F machine pressed precast , prelaminated (lacqure finish) coloured concrete interlocking paver block (VIBROCOMPRESSED AND RUBBER MOULDED) any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 , with grey cement and no pigment and making good on edges with cement concrete 1:2:4 Type B-1 complete all as specified and directed by Engr-in-charge.

M&L for 9 to 10mm thick ( Square) non skid colour heavy duty tiles ( Endura) tiles size 300x300 mm in floor , including dismantling of old broken tiles set and jointed in neat cement slurry and pointed in colour cement with pig ment to match the colour of the tiles over 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer- in- charge

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided, complete all as specified and as directed by the Engr-in-charge.

M&L Precast cement concrete 1:2:4 (using 20 mm graded stone aggregate) as in cover slabs (for manholes etc), chullah hoods, chajjas, shelves and similar articles with pain faces set it cement mortar 1:4, complete all as specified and as directed by Engr-in-charge.

M&L TMT steel bars 10 mm dia and over as in reinforcement, cut to length, bend to shape required including cranking, bending spirally or hooping for coloumns, hooking ends and binding with MS wire (annealed not less than 0.9mm) all as specified and as directed by Engr-in-charge.

S & F in repair concertina coil fencing with punched taps concertina coil 900mm dia 10 m openable length,having 60 Nos rounds per 10 m length ,spring core wire (2.5mm thick ) of hight tensile strength of 145 to 165 Newton per Sq. mm,(Reinforced Barbed Tape ) wire ,stud tied with G.I staple sand G.I clips to retain horizontal , including necessary bolts,complete all as specified and as directed by Engr-in-charge.

M/S SAKET CONSTRUCTION CO.

K R KAUSHAL AND SONS

Saket Traders

ABC CONSTRUCTION COMPANY

M/S AVADH ENTERPRISES

awashyakta enterprises