GE/TOKEN-42/2025-26 SPL REPAIR TO BLDG NO P-44 IHQ OF MOD (ARMY) CIU LOCATION AT BRAR SQUARE, DELHI CANTT ARMY INTERROGATION CENTRE UNDER GE (CENTRAL) DELHI CANTT-10

Amount

M & L for dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for joint less Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including provn of 15mm thick screed bed or bedding layer in CM 1:6 etc complete all as specified .

M&L for joint less Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including provn of 10mm thick rendering of backing coat in CM 1:4 etc complete all as specified .

M & L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement to match the shade of granite stone including grinding, nosing and polishing including 20 mm thick screed bed in CM 1:6 complete all as specified

M & L for Taking down cement plaster in brick walls,including raking out joints,hacking for key,scrubbing down with water etc including scaffolding if required complete all as specified.

M&L for rendering 10 mm thick in CM (1:6) on any faces of concrete or brick surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on any faces of concrete or brick surfaces finished even and smooth without using extra cement complete all as specified.

M&L for rendering 5 mm thick in CM 1 : 3 on brick or concrete surfaces (in ceiling) etc finished even and smooth without using extra cement all as specified.

M & L for applying two coats of cement base paint over one coat of primer on newly plastered surfaces(external) of walls including preparation of new surfaces complete all as specified and directed by Engineer-in-charge.

M & L for two coat of distemper oil emulsion over a coat of primer and 2-3 mm thick JK Birla wall care putty including preparation of new plastered surface of wall complete all as specified and directed.

M & L for applying white wash three coats on newly plastered surfaces of ceiling including preparation of new surfaces for matching with repaired surfaces complete all as specified and directed.

M & L for complete removal of existing old surfaces treatment of wall by scrubbing with wire brush washing down with water and applying two coats of cement base paints, complete all as specified and directed by Engr-In-Charge.

M & L for preparation of old plastered surfaces and applying two coat of oil bound distemper including 2-3 mm thick JK Birla wall care putty on wall including removal of existing old surfaces complete all as specified and directed.

M&L preparing old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and directed by Engineer-in-charge.

Taking down chowkhat or frame with shutters (without taking off shutters from the frame exc 1.5 sqm but nexc 4 sqm each all as spd.

Taking down chowkhat or frame with shutters (without taking off shutters from the frame n exc 1.5 sqm each all as spd.

M&L aluminium alloy powder coated windows including aluminium coated frames silding track, bottom weighing not less than 1.015 Kg/Rm ,sides and top not less than 0.826 kg/Rm double revated and 0.55 kg/Rm for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter silding type with aluminium sectins as per series-A (15mm) 3 track of jindal section number for silding windows with framed shutter including aluminium allow powder coated snap type beads handles with locking arrngement spring action and , glazing clips joint cleats rubber gaskets etc inclding provision of 5.5 mm thick tinted frosted glass of superior quality and stainless steel jali , aluminium grill including all standard fittings complete all as specified and directed

S & F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S & F as pressed steel frames (125x60) mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including one shop coat of primer incl M & L for providing PCC type B-1 ,1:2:4(using 20mm graded stone aggregate) to fill the frame and making good complete all as specified and directed by Engr -in- Charge

S&F 35 mm thick 2nd class hardwood glazed and skelton shutters open rebated and prepared to receive glass / gauze etc ( without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc size of members of shutters as specified in SSRpart-i section 8 clause 8.24(a) ); supplied and fitted to chowkats complete all as specified and directed.

S and F 40 mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified

Supply and fix 300 mm long mild steel sliding door bolt, bolt type stove enameled black with bright bolt not less than 12 mm dia with an including a minimum of six bolts and nuts (four on bolt plate and two on staple plate) complete all as specified and directed.

S & F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

S & F extruded aluminum alloy handles fabricated type and anodised of size 150mm, complete all as specified.

S & F butt hinges medium weight stainless steel 100mm size complete all as specified (Make - Plaza/Classic/Ashish).

S & F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F solid PVC door frame of size 50 x 47 mm made out of 5mm thick plain colour PVC sheet re-inforced with MS square tube, supplying and fixing in opening as per manufacturers instructions drawings and specifications complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30 mm thick (Stiles), with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain Moulded PVC sheet Polyurethane painted on the front face and 2 mm plain color PVC sheet on back face as per specification and drawing complete all as specified.

S & F 100 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

S & F 100 mm aluminium handles, cast type anodised complete all as specified.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces not otherwise described over 10 cm width or girth incl preparation complete all as spd.

M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of old steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

S & F in repair rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, 1000 ltrs capacity.including float valve 20mm size including disconnecting of existing water tank complete all as specified.

Taking up or down 15 mm dia steel tubing and connection incl cleaning or removal to store all as specified

Taking up or down 20mm dia steel tubing and connection incl cleaning or removal to store all as specified

M & L for 15mm bore galvanised steel water tubing medium grade with all fittings (ISI Marked) and fixed complete to walls and or laid under floors etc complete all as specified .

M & L for 20mm bore galvanised steel water tubing medium grade with all fittings (ISI Marked) and fixed complete to walls and or laid under floors etc complete all as specified.

Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Material and labour for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in plinth protection 75 mm thick laid in bays and surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L in repairs PVC connection 15mm dia of standard pattern 450mm long, with two Nos brass check nuts (adopts) and washers etc complete all as specified.

S & F 75 mm bore cast iron soil waste and vent pipe (ISI marked) sand cast in any length with or without ears, with cement joint laid in trenches or in floors or fixed to wall complete all as specified and directed

S & F 100 mm bore cast iron soil waste and vent pipe (ISI marked) sand cast in any length with or without ears, with cement joint laid in trenches or in floors or fixed to wall complete all as specified and directed

S&F Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified.

S&F in repairs PVC waste pipe of standard pattern, 32mm bore socketed end 600mm long for wash basin complete all as specified.

S & F in repairs towel rail 600mm long brass chromium plated of 20mm dia (external) and 1mm thickness with gutties embeded in cement mortar 1:3 with MS screws etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M & L for framed work as in doors, sun shade or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410W-Gde-250 quality A complete all as specified and directed.

S&F in repairs decorative type wooden finish drapery rod,25 mm dia incl side caps and wooden brackets,wooden rings @12 cm distance centre to centre complete all as specified. Vista FE-22 series or equivalent

S&F in repairs fancy type CP brass shower rose with flat panel 125 mm size suitable for 15mm bore pipe complete all as specified and directed .

S & F in repair fancy type brass CP angle valve 15 mm dia complete all as specified

S & F in repair fancy type concealed brass chromium plated stop valve fancy type suitable for 15mm bore of pipe with long shank and cup complete all as specified and directed .

S&F in repair fancy type brass chromium plated bib tap for iron pipe of 15mm bore fancy type with flynut capstan head, screwed down high pressure complete all as specified.

M & L for cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregates as in roof kerbs, or mud stops, rounded or chamfered on edges, coping complete all as specified

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth

M & L for 25 mm sand filling under floors or in foundation including watering and consolidation

Material and labour for machine pressed precast PU coated concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and no pigment laid over 50mm thick compacted sand cushion complete all as specified and directed. (Note : - Sand cushion will be measured and paid separately).

M & L for 75 mm thick cement concrete type D- 2, 1:4:8 (40mm graded aggregate) complete all as specified and directed by Engineer-in-charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M & L for brickwork with subclass- ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6

M&L for 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work as in cup board shutter, loft shutters incl 6 mm thick teak wood lipping and necessary rebating for shutters wherever required including polishing to lipping/rebating complete all as specified.

S&F continuous (Piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 40 mm, complete all as specified.

Supply and fix MS 40mm dia, cup board knobs, glossy finish, fixed with nuts, screw and washer complete all as specified and as directed.

Supply and fix door magnet suitable for cupboard shutters complete all as specified and as directed.

S & F and repair 100 mm aluminium handles, cast type anodised complete all as specified.

Dismantling loose concrete cover of RCC columns,beams,slabs chajjas and the like as directed, roughening and cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry including derusting of steel reinforcement to providing fabric mild steel wire mesh 75X75X3 mm dia as reinforcement to concrete surfaces, applying adhesive admixture over steel mesh and providing minimium 40 mm thick (average thickness) guiniting mix using 1 part of ordinary portland cement 53 grade and 2 part of ghaggar sand mixed with the pressure of 2 to 2.5 kg per sqm by guinting machine including necessary plaster in CM 1:4, 10mm thick to match existing surface and surfaces finised even and fair.all as specificed

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and as directed.

Dismantling of FRP/ asbestos sheet (corrugated or semi corrugated) fixed in roof including ridges all as specified

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 110mm dia PVC (SWR) bends any radius

S and F in repairs vitreous chinaware coloured wash counter wash hand basin size 600x400x185 mm complete including ,CP waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in wall and making good complete all as specified and directed by Engg.in.charge . Make -jaquar cat no-SLS-WST-6601

S&F in repair vitreous china squatting pan (Orissa pattern) long pan (including provision of lime concrete bedding) of size 580x440mm white with intergral footrest including providing 100mm bore CI 'P' or 'S' trap complete all as specified (excluding flushing cistern and flush).

S&F in repairs PVC Low level flushing cistern 10 ltr capacity incl internal fittings,sypons,handle,bend etc incl 2 Nos CI brackets complete all as specified.

M & L in repairs PVC connection 15mm dia of standard pattern 450mm long, with two Nos brass check nuts (adopts) and washers etc complete all as specified.

S&Fin repairs 15 mm dia pillar taps, fancy type brass with capstan head chromium plated screwed down high pressure with or without lettered “hot/cold” with long screwed shank and flynut screwed ,Make-Jaquar/marc/Kohlarcomplete all as specified

S and F in repairs Glass shelf assembly 450 mm long 150 mm wide with cp railing complete all as specified and directed . Make-Cardin cat part no-GS-OP-18 OR equivalent other approved makes.

M & L for 40 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate)

M&L for cement concrete 1:2:4 type B1 (using 12.5mm graded stone aggregate) on roof padding surface finished even and smooth without using extra cement complete all as spd & directed.

M&L providing and applying the plaster with single component ready to use repair mortar (SMART CARE REPAIR MORTAR or equivalent) capable of applying 15mm average thickness in single layer and finishing with trowel with a bond coat: SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area mixed with specified portion of AP SMARTCARE or equivalent Repair Polymer including taking down existing roof treatment of any type including raking out joints, hacking for key, scrubbing down with water etc., to receive further treatment, complete all as specified land as directed.Note: The application shall be executed on any type of surface and on horizontal/Vertical areas.

M&L providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajas in multiple coats @2.0 litre/sqm. Primary [coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Notes: (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) All materials shall be procured directly form manufacturer. The purchase voucher shall be produced to the Engineer-in-Charge for his verification of material. Engineer-in-Charge shall deface the original purchase vouchers. (4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 3% (Three Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor's dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M & L for non skid ceramic coloured tiles of 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white/coloured cement to match with the shade of tiles and including cement screeding 15mm thick in cement mortar 1:6 complete all as specified and as directed

M & L for Glazed ceramic coloured tiles 600x 300 x 9 to 10mm thick in dado, set and jointed in neat cement slurry and pointed in colour cement to match including rendering 10mm thick in cement mortar 1:4 complete all as specified and as directed (Make- Somany/Orient/Johnson/kajaria).

S&F in repair stainless steel gratings 100mm bore size fixed with cement motar.

S&F 75mm cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified

S&F 100mm cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified

S&F 75mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified

Excavation in trenches (soft/loose soil) n exc. 1.5m wide and n exc 1.5 m in depth for foundation etc. and getting out all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M & L for removing excavated material exc. 250m but not exceeding 500m and depositing where directed all as specified.

M&L for 15mm thick rendering on fair face of brick wall surface in CM 1:4 even & fair finishes as specified and as directed.

Supply and laying DWCPE (SN8) 200mm dia pipes and snap fit coupler incl testing and laid properly, jointed laid in trenches to a level on cocrete bed complete all as specified and directed by Engineer-in-charge.

M&L for Sand cushion under floors or in foundation including watering and consolidation

M&L for providing plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified.

Material and labour for medium duty perforated precast machine pressed drain cover slab 80 mm thick of PCC 1:1.5:3 type B-1 and 10mm TMT bars ,including flat iron 150mmx6mm all around the slab and 40mm dia hole at 100mm C/C , size of slab as required at site and complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets light fitting etc. and making good disturbed surfaces of walls, floors ,etc.

Taking down carefully sub main wiring of any description.

Taking down defective switch fuse main board / distribution iron clad or sheet metal enclosure/ MCB DBs with MCBs of any capacity and make including wooden board etc complete all as specified and directed.

M&L point wiring with PVC insulated FRLS 1100 Volts unsheathed cable 1.5 Sqmm multistranded copper conductor and drawing concealed in wall ,on surface in roof/column & including rigid PVC conduit FRLS, medium grade ,ISI marked ,terminal box of 1.6 mm thick and 3 mm thick hylam sheet cover for terminal boxes also including porvision of one run of PVC insulated FRLS 1100 Volts unsheathed 1.5 sqmm stranded copper conductor single core cable as earth wire connected to common earth dolly.

One light/fan/bell point controlled by one way switch

One light point controlled by two, two way switch

One 3 pin switch & socket outlet 5 hole 5 Amps on independent board.

All as above item No100 (c) but Same board.

M & L power point with two runs of insulated stranded copper conductor cable 4 Sqmm single core concealed in wall and one run of PVC insulated FRLS 1100 Volts unsheathed copper conductor 4 Sqmm as earth wire connected to earth dolly complete all as specified and directed.

Provn for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 4 Sqmm in and including new PVC conduit medium grade not less than 20 mm dia, for submain wiring and connection complete FRLS 1100 volts unsheathed stranded copper conuctor cable of 4 Sqmm size stranded conductor single core as earthwire.(Note : for AC/geyser Box)

M&L for submain wiring concealed on wall and surface on column with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 6 Sqmm in and including PVC conduit 25 mm dia, medium grade for submain wiring and one run of FRLS grade,unsheathed copper conuctor cable of 6 Sqmm size as earthwire connected to earth dolly complete all as specified and directed.

M&L for submain wiring concealed on wall and surface on column with two single core PVC insulated FRLS 1100 Volts unseathed stranded copper conductor cable 10 Sqmm in and including PVC conduit 25 mm dia, medium grade for submain wiring and one run of FRLS grade,unsheathed copper conuctor cable of 10 Sqmm size as earthwire connected to earth dolly complete all as specified and directed.

M&L switch Modular type 6 Amp SP one way ISI marked complete all as specified

M&L switch Modular type type 16 Amp SP one way, ISI marked complete all as specified

M&LModular type socket outlet 2 in 1,5 pin 6 Amp , ISI marked complete all as specified

M&L Modular type socket outlet 2 in 1,5 pin 6/16 Amps, ISI marked complete all as specified

M&L Modular type switch 2 way 6A ,1 module type, ISI marked complete all as specified.

M&L ceiling rose 3 phase PVC polycorbonate,isolated body.

S & F Modular electronic fan regulator 5 step,360 degree rotation complete all as specified and directed by engr-in charge.

S & F angle Lamp holder with metallic ring, PVC/Polycorbonate type with back plate complete.

S & F LED bulb 9 watts, >900 lumens output, 6500K, suitable for B-22 base.

M & L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to earth lead GI 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dai and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) including testing ion completion all as directed

M&L distribution board SPN 8 way with 100 Amp rated bus bar double door.

M&L Isolator SPN 40 Amp 240 volt "B " curve.

M&L MCB SP 6 to 32 Amp "B" curve.

Supply and fix LED batten luminaire surface mounted, 4 feet system wattage of 20-22 Watts with lifetime of 25000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.90, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 Degree C, system efficency at luminarie level ≥120 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed by Engr-in-charge.

S&F in replacement of LED batten luminaire surface mounted 2 feet system wattage of 10 watts and not less than 1000 lm with life time of 25000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.90, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficiancy at luminarie level ≥120 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed.

S & F pressure die cast aluminium housing LED street light luminaires with IP66 deg. of protection suitable for 35 watt LED fitting duly fixed on 40 mm dia GI mast including 50X 6 mm thick MS flat with suitable size of fastner including making connection flexible copper conductor cable from ceiling rose to fitting complete all as specified and directed. Note : The Contractor quoated the rates incl all accessories like suitable GI pipe mast, 50x6 mm thick MS flat, fashner, nut & bolts, suitable length of flexiable wire.

S&F in replacement of LED 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of 25000 burning hours at L70 criteria, Power Factor >0.90, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 4 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed complete all as specified and directed by Engr-in-charge.

M&L in replacement distribution board TPN 4 way load line DBs IP 43-IK 09 With metal door with provision of MCCB 160 Amp incomer and including 200 Amp rated bus bar,415 Volts and also Iincluding outgoing SP/TP MCBs 10 nos.

M&L in replacement MCCB 125 Amps, 4 pole 16 ka .

M&L for breaking old existing wall and making a provn for fixing of 300 mm sweep exhaust fan including making good to the disturbed wall/ portion and matching with existing colour.

Provn of exhaust fans AC single phase 230/240 V of size 300 mm sweep with louvre for fixing of exhaust fan complete all as directed by Engr-in-Charge.

S&F in repair sheet metal enclosure single pole and Neutral with a two pin earth plug and socket complete with a MCB SP 10 Amp 220 volts, 50 Hz, 10KA breaking capacity, including fixing completly in wall with sutable sand and cement, complete all as specified and directed.

Provn for Supply and fix surface water heater storage type Geyser vertical type with suitable size of fastner and, inner tank material of superior glass line tank and outer body material of ABS with high pressure with standing enabling (up to 8 bar pressure) capacity including provision and connecting up of SS braidedpipe with adopter for inlet and outlet wwater connection having edjustable knob for temperature control and inner tank should be glass line coated, capacity 25 Ltrs, having heating element 2 KW and not less than 5 star rating, suitable for ,230 volt, 50 Hz electric supply complete all as specified and directed .

Provn for Supply and fixing ceiling fans BLDC fan AC single phase 230/240 V of size 1200 mm sweep ,min air delivery 210 CFM with service value 6.0 BEE, 5 star rated BLDC fan including making connection with three core flexible, copper winding in fan ,copper cable pvc insulated of suitable length and marking of fan no with black paint complete all as directed by Engr-in-Charge.

Schedule of Credit

M/S ANIL KUMAR (BID ID -3409496)

A R S CONSTRUCTION CO (BID ID -3408801)

POONAM ENTERPRISES (BID ID -3406849)

Lamba Enterprises (BID ID -3408689)

ETERNITY PROJECT (BID ID -3409236)

M/S MSD & Associate (BID ID -3416559)

M/s SAAR ENGINEERS (BID ID -3409622)