SPECIAL REPAIR TO BLDG NO P-33/FGH IN MES IB AT MIL STN JAIPUR

Amount

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop mixing with WPC @ 3% weight of cement. Note :- WPC included in this item and no separate payment will be done for WPC.

M & L fibre reinforced, UV resistant elastomeric liquid applied water proofing & Heat reflective coating coating with acrylic Polymers and polyesterfibres,SmartCare Damp Proof or approved equivalent.The coating shall resist 7 bars of water pressure as per DIN 1048 standards, with elongation of 220% as per ASTM D412 & crack bridging of upto 1 mm & with high SRI value conforming to ASNZ standard. And applying three coat of Elastomeric waterproofing coating with recron fibres & High SRI value (Damp Proof) but fisrt coat of should be as primer for terrace waterproofing. Damp Proof is a part of the DSR as per 22.22A and incl repair and preparing of surfacesre. The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

Dismantling of floor /skirting ( terrazzo/ PCC / Ceramic Tiles) including cement mortar bedding (but not backing ) and removing the rubbish from the site.

M&L glazed ceramic tiles in vertical surface 300x200x7 mm / 450x300x7 mm thick set and including 10mm thick layer of rendering bed in cm 1:4 on verticle surfaces and jointed in neat cement slurry and pointed in white or colour cement to match the surface of tiles as on verticle surfaces as skirting and dado etc,complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeing 0.06 sqm but n.exc 0.11sqm(300x300 mm size) in floors etc set and including 15mm thick layer of screed bed in cm 1:6 on floor surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match the shad of tile complete all as specified and directed.

M&L for non-skid Ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. and including 15mm thick layer of screed bed in cm 1:6 on floor surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry including a layer of screed bed 20 mm thick 1:6 and pointed in coloured cement to match the of tiles complete all as specfied

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar.

M&L for granite 18 to 20mm thick as in counter slabs of WHB (of any type) work (table rubbed and polished) in cooking plate forms, counter of WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding complete all as specified..

M&L Machine cut kota stone slab flooring 20 to 25 mm thick over 20mm thick in CM 1:6 cement screed base laid and jointed with gray cement slurry mixed with pigment to match the shade of slab including rubbing polishing fixing complete.

M&L Machine cut kota stone slab 20 - 25 mm thick as in riser of steps, skirting, dado and pillar laid over cement screed/rendering 15 thick in CM 1:4 including rubbing polishing fixing complete.

S&F 15mm PVC connection 600mm long with brass check nut on both sides screw to iron pipes.

Supply and fixed in repair CP angle cock 15mm dia fancy type cast coper alloy (Make-Jaquar (Cat. No. Con-053KN)) and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair CP overhead shower dia 105 mm round with revolving joints (with body rotation) & 115mm long arm shower with rabit cleaning system and all fittings Make - Jaquar OHS-1709 and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixed in repair CP bib cock 15mm dia with crutch handle as approved fancy type two way Bib Cock (Make-Jaquar Con-041KN) and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixed in repair CP bib cock 15mm dia with crutch handle as approved fancy type long body (Make-Jaquar Con-107KN) and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixed in repair CP pillar cock 15mm dia with crutch handle as approved fancy type (Make-Jaquar) and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixed in repair CP bib cock 15mm dia with crutch handle as approved fancy type short body (Make-Jaquar Con-37KN) and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair CP single towel rail 600 mm Make : Jaquar (AQN-7711) and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair Soap dish Make :Jaquar Code (AQN-7731) and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair CP Jet spray Multi purpose 15 mm for bath room complete set Make Zim (Cat No. 1712) and equivalent cat part in other makes as per Appendix 'B'.

Taking down GI tubing 15mm dia, with connections.

Taking down GI tubing 20mm dia, with connections.

S&F tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors for 15 mm bore.

All as per item No. 25 above but 20 mm bore pipe.

S&F in repair PVC Valveless, syphonic action type, Flushing cistern 10 ltr capacity high or low level, white, with inlet, ball valve, float and handle including bracket & flush pipe etc all as specfied and directed.

S&F white vitreous china wash down water closet pan (pedestal pattern) with Plastic water closet seat including seat and seat cover, white,closed pattern with flat bottom, and cover with mild steel chromium plated or aluminised hinging device including connection to drowm pipe and flushing pipe all as specified.

S&F wash hand basin vitreous china white (flat back) of size 550x400mm CI bracket 15mm dia polythene connection 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long etc. complete all as specified, including taking down the existing wash hand basin.

S&F CP grating 100 mm dia round with or without hole fixed on floor/nahani trap fixed with cement complete.

S&F in repair Mirror cabinet PVC/fiber of size 550 x 520 x 100 mm with sliding mirror 4mm thick of size 240 x 290 x 2 Nos with built in rack of size 230 x 150 x 90 mm with PVC plug etc with CP towel rail of length 270 mm and 100 mm dia.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including waste coupling & waste pipe, bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420 bowl size 410mm x 330mm x160 mm.

Dismantling water tanks exc 500 & n exc 1000 ltrs and removing to store

S&F 1000 Ltrs PVC tank rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F in repairs 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

Taking down chowkats or frames (W/out taking of shutters) not exceeding 1.5 Sqm each.

Taking down chowkats or frames with shutter (W/out taking off shutters) exc 1.5 Sqm but n.exc 4 sqm each.

S & F II nd class hardwood plain, solid, straight, chowkats and frames, wrought rebated on the solid, rounded or chamfered put together with glue pinned at joints.

S&F 35 mm thick IInd class Hardwood plain, framed, paneled shutters (any number of panels), with panels of 12mm veneered particle board medium density, wood particle board with commercial face veneers.

S&F 35 mm thick glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc size of members as specified in SSR Pt-I section 8 clause 8.24 (a), in II nd class hard wood.

S & F Solid PVC Door frame of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet reinforce with M.S square tube, high strength suppling & fixing in opening as per specification

S&F Factory Made Solid PVC Moulded Door Shutters with Particle board core 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing suppling & fixing in the frame at site as per specification.

Cutting holes for inserting hold fast and making good to the disturbed portion with cement mortor 1:3 or PCC 1:3:6 exc half brick wall n. exc one brick wall.

M&L flat iron as in hold fast and similar work.

S&F 150mm extruded aluminium alloy handles fabricated type anodised.

S&F 100 mm aluminium alloy anodised hinges and fixed complete all as specified.

S&F 200mm extruded aluminium alloy tower bolts extruted sections anodised.

S & F floor door stopper of brass body and tongue with hard drawn steel spring overall length of cover plate150mm.

S&F Brass sliding door bolt 300mm with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed

Supply only Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

Supply only 5.5 mm thick sheet glass, ordinary quality in squares n.exc 0.50 sq.m in each pane.

S&F 5mm thick looking mirror 25mm beading all around and fixed 6mm thick plywood on back face.

S&F anodized aluminium door & frame powder coating (minimum thickness of powder coating 50 micron) 2mm thick incl 5.00mm thick tinted glass, fixed with anodized aluminium snap beading, glazing clips, joining clips, screws and 02 Nos of aluminium handle on each door shutter, aluminium anodized tower bolt 200mm long 02 Nos on each shutter and mortice lock device complete with double keys for each lock, 01 No floor spring for each shutter complete all as specified and directed with following specifications :- (a) Aluminium door frame =101.50x44.45mm (b) Aluminium style/top & middle rails of shutter=83.5x44.45mm (c ) Aluminium bottom rail of shutter=114.50x44.45mm (d) Aluminium door frame with shutters shall be fixed in position in PCC block wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed.

S&F mild steel powder coated curtain rods (not less than 19 mm dia) includng side globin and end brackets complete.

M&L preparing new surfaces of wood or wood based material exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of wood primer.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L brick work with sub class ‘B’ brick (old size) built in CM 1:4 exc 6m mean radius complete all as specified.

M&L 10 mm thick plaster in CM 1:6 on any surfaces or concrete surfaces finished even and fair without using extra cement.

M&L 15mm thick plaster in CM 1:4 on any surfaces or concrete surfaces finished even and fair without using extra cement.

M&L for preparation of new plastered surfaces of walls & applying two coats of white wash.

M&L for preparation of new plastered surfaces of walls & applying two coats of oil emulsion distemper over a coat of primer.

M&L for preparation of new plastered surfaces of walls & applying two coats of anti-fungal exterior acrylic emulsion paint over a coat of primer.

M&L for complete removal of existing treatment on wall and applying two coats of oil emulsion distemper over a coat primer.

M&L for complete removal plastered surfaces of ceiling and applying two coats of distemper oil emuslion over one coat primer.

M&L for complete removal of surfaces of walls and applying two coats of anti-fungal exterior acrylic emulsion paint over a coat of primer.

M&L for applying two coats of wall putty, 1 mm thick (overall) on wall and ceiling surfaces. (Note :- Quoted rate shall be deemed for two coats)

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specfied and directed.

M&L for plain Cement concrete 1:4:8 type D2 using 40 mm graded stone aggt as in foundation, fillings & mass concrete.

S&F rubber moulded decorative designed coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment laid over and including 25 mm thick fine sand cousion including rolling /compacting the finished surface complete all as specified and directed

Demolition of stone/brick masonry built in cement mortar complete all as specified.

Demolition of cement concrete is reinforced (reinforcement cut as required to facilitate demolition) and removing the rubbish from the site.

M & L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate)for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.

M&L rendering 5mm thick plaster for ceiling on concrete surfaces in CM (1:3) including finish even and smooth with out using extra cement

M&L for PVC SWR floor trap plain with grating including jointing with solvent cement diameter of outlet in 75mm.

M&L for PVC (SWR) gully trap, 125/110mm setting and jointing with solvent cement.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for rain water etc complete.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors.

S&F PVC (SWR) bends any radius 110mm bore dia.

S&F 110mm bore PVC (SWR) branch piece, single (single y) equal or un equal.

Dismantling of 100/75 mm dia cast iron / PVC Pipe or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches or from wall, if required

S&F aluminium anodised powder coated door/ window & ventilators shutter openable/ sliding type fixed type including aluminium section weighing 0.55 Kg/ mtr incl necessary joining cleats, glazing clips, rubber packing snap beading, screws , handle & tower bolts, roller, incl section of handle, inter locking arrangements, top & bottom of shutter complete all as specified

E/M Portion Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete including all fittings such as switches, ceiling roses, pendants, sockets, lamp holder, fan regulator brackets light fittings tube light fitting, bell/ buzzer etc (excluding fans) and making good disturbed surfaces of wall floors, ceiling etc complete all as specified and as directed by Engr-in-Charge to match with existing surface.

M&L Point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including conduit concealed medium grade with all accessories ISI marked, including MS sunken box for mounting fitting like switches, sockets fan regulators modulor type etc. including 1.5 sqmm single core PVC insulated but unsheathed copper earth continuty conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings:-

(a) One light/fan/ bell point controlled by one, one way switch.

(b) One 3 pin 5 Amp socket outlet on the same board with other switches.

(c) One 3 pin 5 Amp socket outlet on independent board with other switches.

All as per Item No 85 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, complete all as specified & directed by Engr-in Charge.

Supply&.Fixing Switch moduler type on top covers (catered in point wiring above) :-

(a) Single pole, one way 6 Amp rating.

(b) Single pole, one way 16 Amp rating.

S&Fixing Socket outlet multipurpose use, on top covers (catered in point wiring above) :-

(a) 5 Pin 6 Amp

(b) 6 Pin 16 Amp

S&F Lamp holder insulated body with back plate for batten fitting.

M&L Ceiling rose surface bakelite 65x50mm, three terminals.

Supply&Fixing speed regulator modular type for ceiling fan electronic type 230 Volts complete.

Supply & fix T5 integrted batten LED Light fittings 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Crompton Cat No LTTB4F20WLED/W and equivalent cat part in other makes as per Appendix 'B'.

Supply & fixing surface mounted LED Mirror light fitting 6 W LED Warmwhite waterproof curve, antique design with fine finishing provide with high power LED, energy saving ,lower power consumption, no RF interference, environmental friendly and recyclable, easy for installation water proof LED Driver suitable for bathroom, bedroom pre-wired twin core twisted flexible copper conductor cable with suitable size all as specified and directed by engineer in charge

Supply & fixing Energy saving new generation 10 W LED IP -65 Bulkhead energy efficient wall mounted made of dia cast aluminium wiht with opal diffuser complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size Make - Halonix Cat No HLBH-02-10CW 10W LED and equivalent cat part in other makes as per Appendix 'B'.

Supply & fix wall Bracket light asthetically designed with B22d & E27 lamp holder including 10W LED Lamp with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Halonix cat Pt No- HLBW-01-B22 and equivalent cat part in other makes as per Appendix 'B'.

Supply and Fixing security lights LED 45 W Energy saving & Environmental friendly long life versatile pressure die cast aluminium IP 66 LED Wall mounted Light Luminaries are made of die casted aluminium body and toughened glass cover for uniformlight spread cames LED technology of Britelite. including bracket made out of suitable size of GI medium grade tubing and fixed with clamps nuts and bolts, washer complete all as specified . Make- CG cat Pt No-LSTS-45-CDL and equivalent cat part in other makes as per Appendix 'B'.

Taking down sub main wiring of aluminum/copper without PVC/ steel conduit.

M&L for Sub main wiring with two runs of 6 Sqmm single core FRLS PVC insulated but in unsheathed multi stranded copper conductor cable 1100 volts grade drawn through and including of 25mm dia PVC rigid conduit medium with conduit accessories and fixed to the surface of wall/ceiling as per ISI including 6.0 Sqmm PVC insulated copper conductor earth continuity wire.

S&F in repair Factory made, sheet distribution boards, double door protection class IP-42 suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 r of the under mention rating:-

SP&N 4 ways

SP&N 8 ways

TPN DB 4 way

S&F in repair MCB 10 KA , C series rupturing capacity of the under mentioned type and rating :-

SP 5 to 32 amps

SPN 32 to 63 amps.

TPN 32 to 63 amps.

M&L Earthing complete with galvanized steel plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground earth pit not less than 2.25 meter deep below normal ground level with top edge of the plate not less than 1.5m below normal ground level connected to GI Strip 25x 4 mm by means of bolts, nuts, check nuts and washer of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I complete all as specified and testing on completion, including provision of earth strip protected by 32 mm dia GI light grade protection pipe from test point to main board and 32 mm GI medium grade watering pipe funnel, PCC earth pit and RCC cover charcoal, salt and GI wire including excavation and earth work etc complete all as directed at site including taking down existing earthing complete.

Supply and fix in repair sheet metal enclosure complete with metallic plug and socket heavy duty moduler type 3 pin (2P + Earth), 25 amp rating single phase 240 volts complete with MCB SP 25 amp “C” series.

Supplying, laying, connecting and testing in trenches, under floors/ roads or on walls Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade, of size 16 sqmm, 4 core including taking down existing eaarthing complete.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core including taking down existing eaarthing complete.

Excavation in trenches n.exc 1.5 metre wide and n.exc 1.5 metre in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, laying cables errection of poles / struts/stays etc n.exe 10 Sqm on plan not exceeding 1.5 metre in depth and getting out in any type of soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in any type of soil.

Removing of excavated material (soil) to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.50metre above the starting point

M & L Sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover.

M&L bricks for protection cover to under ground cable (with old size sub class `B` bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm as directed by Engineer in-charge

JAGDAMBA CONSTRUCTION COMPANY

M/S ROHIT CONSTRUCTION