ADDN ALTN AND IMPROVEMENT TO SINGLE LIVING OFFRS ACCOMODATION AT AFTC COIMBATORE

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep and getting out in hard/dense soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated materials (soils) to a distance not exc 50m and depositing where directed at a level not exc. 1.5 m above the starting point, all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors, all as specified and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 Iitres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete, all as specified and directed.

M&L for providing and injecting Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron etc complete, all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.50 mm graded agrregate) for padding concrete over the roof slab complete all as specified.

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) in filling and mass concrete all as specified and directed.

M&L for RCC type B1 1:2:4 (20mm graded aggregate)in slab supoorted on walls , beams, columns in floor, roofs, landings, balconies, canopies deck slabs and in shelves and the like all as specified and directed.

Chipping/removing loose concrete in cloumns/beams/ chajjas/roof slab etc. up to reinforcement bars without damaging the reinforcement, removing all the loose material and to make all the exposed surface free from dust and all impurities etc complete all specified and directed.

Removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution Reebaklens RR of Fosroc / Sika Rust off 100 / equivalent in bostic India Ltd by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush and applying anti corrosive coating to reinforcement Nitozinc primer of Fosroc/Sika Friazinc R / equivalent in Bostic india Ltd , all as recommended by product manufacturer.

Providing and applying one coat of structural grade epoxy coat by brush of approved make . Mixing of two components will be as directed by manufacturer .Application shall be provided not more than 5 hours before application of micro concrete/polymer mortar etc complete all as specified by the manufacturer. (Make :- Nitobond EP of FOSROCK/ Sikdur 32LP/ equivalent in Bostic India Ltd)

Providing and applying n exc 40 mm thick (In layers of each 10mm thick) Shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar Renderoc SP 40 of Fosroc / Sika plastocrete plus/ equivalent in bostic India ltd, mixed with water in a water & powder ratio 0.18 in ceiling of roof slab/Chajjas/Beams/Parapet walls etc . Note:- Quoted tate is deemed to be inclusive of provideing scaffolding for working in patches upto a height of 15 Mtr complete all as specified and directed.

Supply and application of single component, seamless, spray applied, hybrid elastomeric PU based material i.e Nitoproof 725 of Fosroc chemicals (or) sikalastic 590 of Sika India Pvt Ltd (or) equivalent in any approved make as approved by GE over a coat of primer i.e Nitoproof WB primer of Fosroc chemicals (or) diluted sikalastic 590 of Sika India Pvt Ltd (or) equivalent in any approved make as approved by GE, all as recommended by manufacturer ans as specified. Note:- (i) Average minimum DFTof PU based material shall be 1mm and shall be applied by using a Graco pump. (ii) PU based material shall process the following properties solids by volume -65%, tensile strength ASTM D412-1.75Mpa, density 1.3 g/ml, elongation ASTM D-412-350%, Adhesion to substrate concrete-1.9Mpa, resistance to water-10m pressure. (iii) Rate are deemed to be include for cleaning and preparation of surface to receive PU water proofing system including filling of cracks with cementitious repair mortars i.e renderoc CS of Fosrock chemicals (or) equivalent of approved make. (iii) Work shall be got carried out by authorised applicator of the manufacturer and it shall be got approved by the GE before progressing the work. (iv) 10 years of guarantee shall be provided and security amount shall be deposited as speicified in tender documents.

M&L for brick work with flyash bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 complete all as specified and directed.

M&L brickwork with fly ash bricks straight or curved on plan exc 6m mean radius half brick thick walls, built in CM 1:4 complete all as specified and directed.

Hydraulically pressed burnt clay tile plain of size 200x200x19/20mm machine made laid over & including cement mortar screed 15mm thick in CM 1:6 mixed with water proofing compound and jointed pointed in CM 1:3 mixed with 5% crude oil by weight of cement

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified.

M&L for IInd class hard wood , Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed.

M&L for flat form work for fair finished surfaces to soffits of suspended slabs such as roof slabs , floor slabs, landings and similar work; not exceeding 200mm thick (horizantal or sloping) all as specified and directed.

S&F 40mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and both faces are covered with decorative face veneer with lipping/frame to match, all as specified and directed.

S&F 35mm thick IInd class hard wood ,Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, all as specified and directed.

S&F 35 mm thick ,IInd class hard wood, glazed and skelton shutters ;open rebated and prepared to receive glass, gauze, etc.(without sash bars), edges of framing plain, chamfered or rounded; fitted with mitred beads for securing glass wtc; size of members as specified in SSR part-I section 8, clause 8.24(a), all as specified and directed.

S&F heavy duty single partition sliding door fitting kit suitable for 150 kg weight of door including all necessary items required like Roller bracket madeup of SS 304, 6 Nos solid metal 35mm x 40mm track, Bottom solid metal guide, 7omm dia double bearing wheel with 27mm solid metal bushing, Solid metal end stop with shock absorber rubber etc, all as specified and directed.

M&L for 12mm veneered decorative plywood, grade I with decorative face veneers on one face all as specified and directed.

M&L for 18mm veneered decorative plywood, grade I with decorative face veneers on one face all as specified and directed.

M&L for providing and injecting At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same, all as specified and directed.

Mild steel TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (anneled) not less than 0.9mm dia or securing with clips all as specified and directed.

S&F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut tolength, bent to shape required, including cranking, bending and hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&F Mild steel framed work such as grills , gratings etc and similar work conforming to Fe-290 Gde E-165, all as per specified & directed.

Spply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof SS wire mesh (Two nos glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116x45mm & sash 46x62mm both having wall thickness of 2.3+ 0.2mm and single glazing bead/double glazing bead of appropriate dimension. ( Area of window above 1.75 sqm) comprising of uPVC multi chamfered frame, with inbuilt roller track and sash extruded profiles duly reiforced with 1.60+0.2mm thick galvanised mild steel section made from roll forming process of required length ( shape and size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC exruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (Weight bearing capacity to be 40kg), GI fastners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. profile of frame & sash shall be mitred cut and fuson welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame , the gap between frameand adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality , complete all as specified and directed. (NOTE- Glass and wire mesh shall be measured & paid separately)

Spply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47x50mm mullion 47x68mm both having wall tickness of 1.9+ 0.2mm and single glazing bead of appropriate dimension. ( Area upto 0.75 sqm) comprising of uPVC multi chamfered frame,and mullion (where ever required) extruded profiles duly reiforced with 1.60+0.2mm thick galvanised mild steel section made from roll forming process of required length ( shape and size according to uPVC profile), uPVC extruded beads of appropriate dimension of EPDM gasket, GI fastners 100 x 8mm size for fixing frame to finished wall, plasyic packers, plastic caps and necessary stainless steel screws etc. profile of frame shall be mitred cut and fuson welded at all corners,mulion (if required) shall be also fusion welded including drilling of holes for fixing of hardwares and drainage of water etc. After fixing frame , the gap between frameand adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and approved quality , complete all as per approved drawing & direction. (NOTE - Glass and wire mesh shall be measured & paid separately)

Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( +/ – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +/– 0.2mm thick, alvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners for area of windoe not exceedind 1 Sqm and including following hardware :- Hardware: (i) Casement handle made of zinc alloyed (white powder coated) (ii) Butt Hinges of zinc alloyed (white powder coated). (iii) Transmission gear made of mild steel with multi point locking system. (Notes: (i)Glass and wire cloth shall be measured & paid separetely. (ii) Net opening will be measured for payment purpose.

Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( +/ – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +/– 0.2mm thick, alvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners for area of windoe exceedind 1 Sqm but not exceeding 2 Sqm and including following hardware :- Hardware: (i) Casement handle made of zinc alloyed (white powder coated). (ii) Butt Hinges of zinc alloyed (white powder coated). (iii) Transmission gear made of mild steel with multi point locking system] Notes: (i)Glass and wire cloth shall be measured & paid separetely. (ii) Net opening will be measured for payment purpose.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, specified and directed.

Supply only Intergral waterproofing compound

S&F heavy duty parking tiles 300 x 300 x 15mm, laid and and jointed complete all as specified and directed.

M&L for Screed bed or bedding layer of mortor 20 mm thick in CM 1:4 for laying floor finishes all as specified and directed.

M&L for Screed bed or bedding layer of mortor 15 mm thick in CM 1:6 for laying floor finishes all as specified and directed.

M & L for dark shade/Double charged/ultra charged vetrified ceramic tiles 10mm thick (Square/rectangular) Polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for dark shade/Double charged/ultra charged vetrified ceramic tiles 10mm thick (Square/rectangular) Polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for Non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but exceeding 0.11 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge..

M & L Glazed coloured ceramic tiles in vertical surface 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed.

Granite (of any type) tiles 20-22 mm thick machine cut, bedded andjointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

Sadrahalli stone (of any type) tiles 20 -25mm thick machine cut, bedded andjointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

Sadrahalli stone (of any type) tiles 20-25mm thick machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exceeding 50m, all as specified and as directed.

S&F set of Nylon rollers mounted on MS fittings, top & bottom latches and suitable fitting for sliding of door , complete suitable for 12mm thick sliding ward robe all as specified and directed.

S&F Powder Coated (minimum thickness of powder coating 50 micron), anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F Continuous (piano) hinges, brass 40mm width of flaps (when open), all as specified and directed.

S&F 100mm extruded aluminium alloy handles, fabricated type anodised all as specified and directed

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in all as specified and directed.

S&F brass Locks, cupboard, grade I, size 50 mm all as specified and directed

S & F Factory made solid PVC Moulded door shutter with wood EPS, 30mm thick , with 2,4, or 6 raised panel design with 2mm thick moulded prelaminated PVC Sheet on both faces supplying & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed.

S&F 75 mm long butt hinges, type C-22 extruded aluminium anodised with brass hinge pin, anodised and fixed and all as specified and directed

S&F 100mm long Aluminium anodised barrel towers bolts of extruded section and all as specified and directed

S&F 150mm extruded aluminium alloy handles, fabricated type anodised as specified and directed

S&F stainless steel wire cloth 00.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples, all as specified and directed

S&F 100mm long butt hinges, medium weight, cold rolled mild steel with brass/bronze hinge pin, all as specified and directed

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, all as specified and directed

S&F 200mm long Aluminium anodised, barrel tower bolts of ex?truded section and fixed, all as specified and directed

S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, all as specified and directed

S&F in repair stainless steel wire cloth 00.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless stell wire staples.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

S&F 3 mm figured glass, ordinary quality , n exc 0.5 sqm in each glass all as specified and directed.

S&F 4mm sheet glass, ordinary quality , exc 0.5 sqm in each glass all as specified and directed.

M & L Rendering in CM 1:3, 5mm thick on fair faces of brick work or concrete surfaces on ceiling complete all as specified.

M&L for Rendering with WPC in CM 1:4, 15mm thick on othe than fair faces of brick work or concrete surfaces all as specified and directed. Note : WPC shall be measured and paid separately

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces with CM 1:4 as in backing coat of skirting /dado all as specified and directed.

M&L for Rendering in CM 1:6, 10mm thick on fair faces of brick work or concrete surfaces all as specified and directed.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling.surface all as specified.

M & L prepaeation newly plastered of wall surfaces and applying two coats of acrylic smooth exterior paint of required shade (applied @ 1.67ltr/10 Sqm) over and including priming coat of exterior primer @2.20 Kg/10 Sqm) all as specified .

M & L prepation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over over a coat of primer over 3mm thick wall care putty on wall all as specified and as directed .

M & L for preparation of old treated surfaces of ceiling and applying two coats of white wash on ceiling.surface all as specified.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces all as specified and directed.

M&L for applying one coat of synthetic enamel paint preparation of old wooden surfaces all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces all as specified and directed.

M&L for applying one coat of synthetic enamel paint including preparation of old steel surfaces all as specified and directed.

Complete removal of existing treatment on wall surfaces and applying two coats of acrylic smooth exterior paint of required shade (applied @ 1.67ltr/10 Sqm) over and including priming coat of exterior primer @2.20 Kg/10 Sqm) all as specified and as directed directed by Engr-in-charge.

Complete removal of existing treatment on old decorated surfaces of wall and applying two coats of distemper oil emulsion over primer over 3mm thick wall care putty including preparation of wall all as specified.

Supplying and laying CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings with brass threading fixed to wall/ceiling or laid in Floor for 20mm outer dia of pipe, complete all as specified & directed.

Supplying and laying CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings with brass threading fixed to wall/ceiling or laid in Floor for 25mm outer dia of pipe, complete all as specified & directed.

S&F Rimless bowl with cistern for extended wall hung WC , size 380 x650x 730mm with PP soft close seat cover, hinges, dual flush cistern fittings, accessories set, etc Make : Jaquar Model No : FLS-WHT- 5353PPZ or equivalent including taking down of existing one complete all as per specified and as directed.

S&F single lever wall mixer 3-in-1 system with provision for both hand shower and over head shower complete with 115mm long bend pipe , connecting legs & wall flange (Excluding over head shower but including hand shower and flexible pipe hand shower) Jaquar Model No : KUP-35125PM or equivalent in oter make specified .

S&F Stainless steel toilet paper holder. Jaquar Model No : AKP-35753PS or equivalent including taking down of existing one complete all as per specified and as directed.

S&F WHB with pedestal and click clack type coupling, Jaquar Model No : CNS-WHT-801 (for WHB), CNS-WHT-305 (for pedestal) & ALD-727(For coupling) , or equivalent including taking down of existing one complete all as per specified.

Supply and fix PVC cabinet of size 600 x 450mm with shelves and hinged cover all as specified and as directed.Make : Parryware / Kohinoor/ Sintex

S&F single lever wall mixer with provision for over head shower with 115mm long bend pipe on upper side, connecting legs & wall flanges, Jaquar Model No : OPP-15117PM or equivalent including taking down of existing one complete all as per specified .

S&F two way Bib taps, brass chromium plated fancy type with wall flange screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. Make : Jaquar . Model No :OPP 15041PM or equivalent including taking down of existing one complete all as per specified.

S&F Single lever basin mixer without popup, brass chromium plated fancy type with wall flange screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore, Jaquar Model No :OPP 15011BPM or equivalent including taking down of existing one complete all as per specified .

S & F PVC connections 15 mm size with PTMT nuts of length 600 mm, all as per specified & directed.

S&F angular stop cock with wall flage screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore. Make : Jaquar . Model No :OPP 15053PM or equivalent including taking down of existing one complete all as per specified .

S&F over head shower 200 x200 mm square shape flow(ABS Body chrome plated with grey face plate) with Rubit cleaning system, Jaquar . Model No :OHS-35497 or equivalent including taking down, all as per specified & directed.

S&F brass chromium plated health faucet with hand held and spring operated control valve with PVC flexible pipe connection of suitable length as directed fixed to 15 mm bore pipe, Jaquar Model No :ALD-565 or equivalent including taking down, all as per specified & directed.

S&F stainless steel towel rack with lower hanger and hook , Jaquar Model No : AHS-1581H or equivalent complete, all as per specified & directed.

S&F stainless steel towel ring square, Jaquar Model No : AKP- 35721P or equivalent complete, all as per specified & directed.

S&F Glass shelf with bracket, Jaquar Model No : CAN-1173 or equivalent complete, all as per specified & directed.

S&F soap dish (poly carbonate), Jaquar . Model No : AQN-7733 or equivalent complete, all as per specified & directed.

M & L 110mm dia for PVC (SWR) multi floor trap of with grating including jointing with solvent cement.

M & L 75mm dia for PVC (SWR) multi floor trap of with grating including jointing with solvent cement, all as per specified & directed.

S & F in repairs 110mm dia PVC (SWR) pipe single sockted in any length with rubber ring joints fixed to wall with clamp, all as per specified & directed.

S&F 110mm radius PVC (SWR) bends complete, all as per specified & directed.

S&F 110mm radius PVC (SWR) branch piece, single (single Y) equal or unequal complete, all as per specified & directed.

S&F 110mm radius PVC (SWR) branch piece, double (double Y) equal or unequal complete, all as per specified & directed.

S & F in repairs 75mm dia PVC (SWR) pipe single sockted in any length with rubber ring joints fixed to wall with clamp complete, all as per specified & directed.

S&F 75mm radius PVC (SWR) branch piece, single (single Y) equal or unequal complete, all as per specified & directed.

S&F 75mm radius PVC (SWR) branch piece,double (double Y) equal or unequal complete, all as per specified & directed.

S & F 50mm dia Unplasticised PVC pipe of pressure rating 10 kgf /cm2 fixed complete to walls, ceiling or in floors.

M & L for 125/110mm dia PVC (SWR) gully trap includingsetting jointing with solvent cement, all as per specified & directed.

S&F 110 mm bore PVC (SWR) vent cowl, all as per specified & directed.

S&F 25 mm dia SS drapery rod , including brackets, decorative knobs at both ends & curtain rings 8 Nos (minimum) complete all as speccified and directed.

Disconnecting existings HDPE water tank 500 Ltr capacity , setting a side (or lowering if required) for repairs, claening, etc. and hoisting if required reconnecting and refixing in position. (NOTE - Cleaning repairings, etc. measured sepaeately).

Cleaning and removing all scale and dirt etc, from HDPE tank 500 ltr capacity and from mouths of circulating pipes, etc. complete, all as per specified & directed.

S&F moulded polyethylene 1000 ltr water tank storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F in repairs 25 mm Ball brass valves, high pressure, with polythene float and flynut cimplete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F of 1.5mtr long pully operated cloths drying system consisting of chormiun plated pipe of outer dia 22mm, inner dia 19.80mm, pulleys made up of delrin with nylon rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable ) locking system to hide rope knot, channel to be mounted or fixed with self tapping screws provided in kit. Rope will be HDPE double core of 4mm dia , fixing to ceilling as specified and directed and minumum weight of one pipe shall not be less than 0.20kg/m, minumum weight of rope shall not be less than 5500gms/unit ( for 06 pipes), all as specified and directed.

M& L painting of Ceiling fan complete, in situ with synthetic enamal paint by spraying incl filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed.

Supply and fixing A/C Starter of capacity 25 Amps complete all as specified. Make: L&T/Legrand/ Havells

M&L for concealed Point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed for the following :- (a) One light point controlled by one, one way switch.

(b) One ceiling/exhaust fan point controlled by one, one way switch.

(c) One switch socket outlet point 5 Amps on independent board.

(d) One 05 Amps socket outlet point on same board.

(e) One Bell point controlled by one, one way Bell push button.

(f) One , 2 way light point controlled by 2, two way switches.

M&L for concealed Point wiring complete with 4 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed for one 3 pin socket outlet, 15 Amps on independent board. Note for item No. 121 to 127 : Cutting chases and making good in wall / floor will be Measured and paid seperately.

Supply and fixing Modular white cover plate with frame 1 module complete as specified and directed.

Supply and fixing Modular white cover plate with frame 2 module complete as specified and directed.

Supply and fixing Modular white cover plate with frame 3 module complete as specified and directed.

Supply and fixing Modular white cover plate with frame 6 module complete as specified and directed.

Supply and fixing Modular white cover plate with frame 8 module complete as specified and directed.

Supply and fixing LED lights fitting 1x 16W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 5 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Bell multi music type , single pole, AC, 230 volts complete all as specified and directed.

S&F Modular bell push 6A single pole, one way, 1 module complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply & fix wall light Decorative, wall mounting, brushed nickle finish fixture with opal glass diffuser including for 4 W LED filament lamp E14 base complete with making connection by using twin core flexible twisted copper wire from ceiling rose to light fittingcomplete all as specified and directed.

Supply and fix sheet metal enclosure with distribution board (DB) TPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 04 way compact double door suitable for fixing MCBs TPN as in commer and out going complete all as specified and directed.

Supply and fix MCB DB, SPN, 4 ways, Isolated neutral bar with double door IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete all as specified and directed.

Supply and fix MCB TPN 63 Amps, 240Volts, 10 KA, "B" Curve complete all as specified and directed.

Supply and fix MCB TP 32 Amps, 240Volts, 10 KA, "B" Curvecomplete all as specified and directed.

Supply and fix MCB SPN 20 Amps, 240Volts, 10 KA, "B" Curvecomplete all as specified and directed.

Supply and fix MCB SP 6 to 32 Amps, 240Volts, 10 KA, "B" Curve complete all as specified and directed.

Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals, complete all as specified and directed.

S&F Modular fan regulator step type 100 W, 2 module complete all as specified and as directed.

S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed.

S&F Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed.

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed.

M&L for concealed Sub main wiring by making recess in wall/surface complete with 2 runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface/concealed in wall/Ceiling etc for three phase sockets all as specified and as directed. (Note :- (i) 2 runs of 4 sqmm, + 1 run of 4 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length) (ii) Cutting chases and making good in wall / floor will be Measured and paid seperately.

M&L for concealed Sub main wiring by making recess in wall/surface complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface/concealed in wall/Ceiling etc for three phase sockets all as specified and as directed. Note :- (i) 2 runs of 6 sqmm, + 1 run of 6 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length) (ii) Cutting chases and making good in wall / floor will be Measured and paid seperately.

M&L for concealed Sub main wiring by making recess in wall/surface complete with 4 runs of 10 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 10 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories suface/concealed in wall/Ceiling etc for three phase sockets all as specified and as directed. (Note :- (i) 4 runs of 10 sqmm, + 1 run of 10 sqmm (Earth Cotinuity conductor) and 1 run of PVC conduit shall be measured as one unit length) (ii) (ii) Cutting chases and making good in wall / floor will be Measured and paid seperately.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth

Supply and fix sheet metal enclosure with distribution board vertical (DB) VTPN, 415 volts, having IP:43 protection, isolated neutral bar, insulated busbar assembly, door earthing arrangement, mechanical impact strength IK08, 12 way double door suitable for fixing MCCB160/ 250 Amps as incommer and F2 Frame MCBs TPN as out going complet, fixed on wall and connecting with all electric connections/circuit complete all as directed. .

Supply and fix MCCB 3 pole, 36 KA, 415 V, , adjustable thermal setting, 350 Amps complete all as specified and directed.

Disconnecting carefully electric energy meter single phase and keeping aside , and re-fixing the same after necessary wiring work complete.

Supply & fixing LED focus light 7 watt wall mounted suitable for bed side light complete all as specified and directed.

M&L for riddled earth filling in trenches above and below the cable as in cable protection. (Note:- Punned thickness shall be mesured and paid.)

Material and Labour in replacement for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, multi stranded, 1100 volts grade, cross-sectional area 150 Sqmm, 3.5 core with and including making connection by using necessary thimbles complete all as specified and directed. .

Material and Labour in replacement for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, multi stranded, 1100 volts grade, cross-sectional area 240 Sqmm, 3.5 core with and including making connection by using necessary thimbles complete all as specified and directed.

Material and Labour in replacement for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, multi stranded, 1100 volts grade, cross-sectional area 25 Sqmm, 4 core with and including making connection by using necessary thimbles complete all as specified and directed.

Supply and laid well burnt bricks sub-class 'B' designation 75 for cable protection, brick shall be laid dry flat as width of brick eqals to the length of cable and the gap between two adjacent brick shall not exceeded 10 mm, complete all as specified and as directed.

M&L for GI pipe 80 mm dia light grade with all fittings for cable protection laid under road/path/hard standing or fixed with wall/pole etc complete.

M&L for cutting of existing bituminous road/path/hard standing suitable for laying cable protection pipe 80 mm dia under the road/path/hard satnding at a depth not less than 60 CM below the normal ground level, Returning filling soil and making good the disturbed surface of road/path/hardstanding by using cement concrete mortar 1:3:6 type C2, using 40 mm graded stone aggregate 0.30 mtr wide and 0.30 mtr thick complete all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead GI wire 4mm dia ( 8 SWG) connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board/ feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:2:4 type B-1 & RCC cover and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009, complete all as specified and directed. NOTE - The unit rate includes earthwork, earthing wire and protection pipe upto 7.5 metre.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , galvanised iron strip 32 x6 mm as earthing lead connectd to GI earth plate electrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board and protected by galvanised iron pipe medium grade 40mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:2:4 type B-1 & RCC cover in M-20 (Design mix ) and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009, complete all as specified and directed. NOTE - The unit rate includes earthwork, earthing wire and protection pipe upto 7.5 metre.

M&L for earth coninuity conductor or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit / pipe or fixed to pole or any other indicated situation or for loop earthing complete of Galvanised Iron strip size 32x6 mm fixed by using and including suitable size of porcelain insulators in such a manner that strip can be separeted from the wall, complete all as specified and directed.

M&L for 4 mm dia galvanised iron or steel wire as earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required complete.

M&L for test point terminal block made of gun metal or phosphorous bronze size 75x75x25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hex head screw, complete all as specified and directed.

M&L for PVC pipe 40 mm dia unplasticised pipe of pressure rating 10 kg/cm2 laid in trenches under road/path/hard standing or fixed with wall/pole etc, complete all as specified and directed.

M&L for cutting of existing bituminous road/path/hard standing suitable for laying cable protection pipe 40 mm dia under the road/path/hard satnding at a depth not less than 60 CM below the normal ground level, Returning filling soil and making good the disturbed surface of road/path/hardstanding by using cement concrete mortar 1:3:6 type C2, using 40 mm graded stone aggregate 0.30 mtr wide and 0.30 mtr thick complete all as specified and directed.

S&F of Copper air termination rod 12mm dia 300 mm long with all accessories to fix at the existing position, top of roof level all as directed.

Refixing only exhaust fan including carrying out cleaning, servicing, greasing oiling and connecting up including provision of cable from celling rose/ connector to fan all as specified and as directed.

Refixing only Ceiling fan with and including carrying out cleaning servicing, oiling and greasing of ceiling fans and connecting up including provision of cable from celling rose/ connector to fan all as specified and as directed.

Removal of debris/building material out side the campus including loading and unloading, etc to a distance exc 5Km but n exc 10 km out side the MD land complete all as specified and directed. (Note:- Location and permission of depositing the building materials/debris disposal outside the MD land shall rest with contractor at his own arrangement)

Taking down cement plaster on brick or stone walls, ceilings, etc including racking out Joints, hacking for key, scrubbing down with water, etc

Removal of Plants/ Shrubs grown on walls/ slabs/beams by making holes or demolition of concrete etc and including applying suitable chemical for killing the roots of Plants, filling of holes with concrete and making good complete all as specified and directed.

Taking down and refixing in same opening of shutters of any description exc 1 sqm and n exc 2sqm each all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2sqm each all as specified and directed.

Taking down chowkhats or frames with shutter (with out taking off the shutters from the frames) size not exc 1.50 sqm each and all as specified and directed.

Taking down chowkhats or frames with shutter (with out taking off the shutters from the frames) size exc 1.50 sqm but not exceeding 4 sqm each and all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Taking up or down steel tubing and connections, and removing to store for taking in account of credit for 15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections, and removing to store for taking in account of credit for 20mm bore complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortor bedding (but not backing to stone and rubbish off the premises complete all as specified .

Demolition of Stone sett paving of any description or thickness, laid bedded and pointed in any mortar

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Taking down existing roof treatment including clay tiles, screed bed , APP membrane etc top of roof slab and cleaning with wire brushe and washing with water complete , including removal and dispose off the debris all as specified .

Dismantling of HDPE water tank 500 ltr capacity and removing to store

Taking down old unserviceable point wiring (light, fan socket or power) complete, including fixture and fittings such as switches,ceiling rose, pendents, regulators,sockets, light fittings etc.removing materials for keeping for taking credit( credit for above items should be made as per conditions separately) and making good disturbed surface of walls floors etc. all as specified.

Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceilingfittings, bulk head fittings, tube light fittings and regulators, etc. for reuse to be handed over to AGE(E/M) stores.

Taking down old unserviceable submain wiring of any size including GI/copper earth continuity conductor in PVC conduit on wall/roof and making good to disturbed surfaces all as directed.

Taking down exhaust fan, sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Disconnecting electric connection and taking down main switch/DB of any size and keep in safe custody for taking credit complete and good/levelling the disturbed surfaces of wall to match with existing surface.

Taking down Ceiling fan sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Taking out old unserviceable underground cable of various sizes all as directed.

Taking Down old strips of various sizes from site against item ser no 02 above as directed.

M Mohan Babu

S KUMARAN

K. VENKATESH NAIDU

P Natesan and Co

power links

Lucky Enterprises

FUTURE ONE FACILITY MANAGEMENT