SPECIAL REPAIR OF OTM ACCN T-33 CARNATIC LINES, T-23 AND T-25 (POONCH LINES) AND OR MD ACCN P-15 (01 BLOCK) URI LINES AT DAMANA UNDER GE JAMMU

Amount

B/R Portion: - Taking down chowkhats or frames with shutter without taking off shutter from the frame not exceeding 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down chowkhats or frames with shutter without taking off shutter from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removing unserviceable material exceeding 100 metre complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and as directed.

Dismantling asbestos cement (corrugated or semi corrugated etc) sheets in roof covering complete all as specified and as directed.

Dismantling timber scantling 40 Sq cm and over in section framed work of any description complete all as specified and as directed.

Demolition of brick masonry built in cement mortar including all quions, arches, pillars etc complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including racking out joints hacking for key scrubbing with water etc complete all as specified and as directed.

Dismantling boarding of any description fixed in any position with nail including GI frame work complete all as specified and as directed.

Dismantling floors, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling of PVC cast iron 100mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

Dismantling of PVC cast iron 75mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

Taking down GI tubing of 15 mm dia and connection and including cleaning complete all as specified and directed.

Taking down GI tubing of 20 mm dia and connection and including cleaning complete all as specified and directed.

Dismantling / disconnecting / demolition of water storage tank of any type or description PVC exceeding 250 and not exceeding 500 litres capacity complete all as specified and as directed.

Taking out the roots of trees / shrubs of any girth from the surface of buildings and making good the damaged portion to match with the existing surface in CM (1:3) or with PCC (1:2:4) or brick work in CM (1:4) and finally finishing the surfaces to match with the existing surfaces complete all as specified and as directed.

Material and labour for brick work of old size sub class ‘B’ bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for brick work of old size sub class ‘B’ bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) except bricks complete all as specified and as directed.

Supply and fixing pressed steel frames for door (factory made) out of 1.25 mm thick black mild steel sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete size of frame 105 x 60mm including bottom of each chowkhat to be welded with 2 No's 25 x 25 x 3 mm thick flat iron projecting 10 cm on either side and back fill to chowkhats with PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) including one shop coat of red oxide primer complete all as specified and as directed. Note: - PCC (1:3:6) type C-0 as in backfill will be measured and paid separately.

Supply and fixing pressed steel frames for door (factory made) out of 1.25 mm thick black mild steel sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete size of frame 125 x 60mm including bottom of each chowkhat to be welded with 2 No's 25 x 25 x 3 mm thick flat iron projecting 10 cm on either side and back fill to chowkhats with PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) including one shop coat of red oxide primer complete all as specified and as directed. Note: - PCC (1:3:6) type C-0 as in backfill will be measured and paid separately.

Material and labour cement concrete (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) as in backfill of pressed steel door frames complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

Supply and fixing 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 35 mm thick 2nd class hard wood half glazed and skeleton shutters open, rebated and prepared to receive glass / wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass / wire mesh etc sizes of member as per clause 8.20(a) of SSR part-I for door shutter complete all as specified and as directed.

Supply and fixing steel door factory made box type (primer coated) ERW hollow section 3.0 mm thick, size for vertical and top rail 100 mm x 35 mm, size of middle rail 150mm x 35mm and bottom rail of size 200mm x 35mm single rebated comprises wire gauged skeleton shutter with two No's of FI section complete welded to frame for holding wire mesh complete all as specified and as directed. Note: - Wire gauge shall be measured and paid separately.

Supply and fixing framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Material and labour for 18 / 19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in cupboard shutters / pelmet box and cupboard shelves including teak wood beading all around complete all as specified and as directed.

Supply and fixing 4mm thick of size 605 X 605 mm, white pre-premiered, self embossed, reinforced designer board for false ceiling conforming to IS-14862 and ISO-8336:1993 as per specification under mentioned: - (i) GI section frame work (POWDER COATED) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange. 33mm thick powdered coated main tee 38 (Web) X 24mm flange 0.33mm thick wall angle screwed fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm centre to centre, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm centre to centre to soffits. To from grid of 610 X 610mm cross tee shall be provided @ 610mm centre to centre in both directions. Suitable provisions shall be made for fixing the recessed / surface mounting light fittings if any complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for structural steel works of Fe-410W (Gde 'E' 250) quality 'A', as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate / red oxide primer paint (including preparation of surface) before fabrication complete all as specified and as directed.

Supply and fixing plates (plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

Material and labour for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 22.5 cm and not exceeding 30cm long, Diameter of neck 16mm to 20mm complete all as specified and as directed.

Supply and fixing pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) in type B-1 (using 20mm graded crushed stone aggregate) beams, cantilevers, bressummers, lintels over 1.5m span, as in lintel band complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs not exceeding 20cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces complete all as specified and as directed by Engineer-in-Charge.

Material and labour for steel reinforcement TMT bars 10 mm dia and over cut to length, bent to shape and tying with annealed mild steel wire 0.9mm dia complete all as specified and as directed by Engineer-in-Charge.

Material and labour for steel reinforcement TMT bars 5mm dia and over upto and including 10 mm dia as in binders, stirrups, spacer complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing box type steel windows / Ventilator (factory made) outer frame made out ERW tube 'P' section 65 X 45 X 25 mm and shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and directed and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3. Note: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 no's MS steel lugs made of 20 X 5 mm iron flat 200 mm long. iii) 10 mm Sq Bar grill / guard bar design as per drawing. (iv) PCC block for embedding lugs.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge. Note: - The cost of form work required for these item shall be deemed to be included in the unit rate of this item.

Hacking out old broken glass of any thickness, size, quality or description from the wooden / steel frames glazing with putty or fixed with wooden beads complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 3.0 mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads nails etc. to wooden surfaces as in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 3.0 mm thick figured glass, pin headed / frosted head type and glazing with oil putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Supply and fixing in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanized with staples including one coat of red oxide primer complete all as specified and as directed.

Supply and fixing mild steel butt hinges 100mm long medium weight cold rolled complete all as specified and as directed.

Supply and fixing 100 mm long hasp and staple, aluminium anodized with bolt to hinge plate and fixed with screws complete all as specified and as directed.

Supply and fixing aluminium anodised barrel tower bolt of size 150 mm complete all as specified and as directed.

Supply and fixing aluminium handle cast type anodized of size 150 mm complete all as specified and as directed.

Supply and fixing in repairs 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gram), screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Supply and fixing in repair mild steel helical / ordinary rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding (ISI marked) complete all as specified and as directed.

Supply and fixing small fittings 2nd class hard wood such as brackets of any types latch and hings blocks shaped door and window stops and the like, not exceeding 200 cu.cm each complete all as specified and as directed.

Supply and fixing Aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Material and labour for 25 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in floor finished rough complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles 450 x 350 x 7 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including 10 mm thick screed in CM (1:4) complete all as specified and directed.

Material and labour for non skid ceramic tiles 7 to 8 mm thick (square / rectangulament) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors over 15 mm thick screed in CM (1:6) set and jointed in neat cement slurry and pointed in white / coloured cement with pigment to match complete all as specified and directed.

Material and labour for non skid ceramic tiles 7 to 8 mm thick (square / rectangulament) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors over 15 mm thick screed in CM (1:6) set and jointed in neat cement slurry and pointed in white / coloured cement with pigment to match complete all as specified and directed.

Material and labour for green marble 18 to 20 mm thick (table rubbed and polished ) in staples jambs, pillars, window cill, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20 mm thick screed in CM (1:6) set and jointed in neat cement slurry and pointed in white / coloured cement with pigment to match complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring 20-25 mm thick laid over cement screed base 20mm thick in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and as directed.

Material and labour for machine cut kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over cement screed bed of 15mm thick in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and directed.

Material and labour for rendering 15 mm thick cement plaster (1:4) on fair faces of brick work or concrete surfaces and to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 5 mm thick cement plaster (1:3) on fair faces of concrete surfaces as in ceiling, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 15 mm thick cement plaster (1:3) on surfaces other than fair faces of concrete surfaces as on facia of roof slab, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and directed. (including all necessary scaffolding, lifting arrangment for three storey building on external surfaces).

Supply and fixing in repair PVC (SWR) 'P' trap 110 / 110 mm bore complete all as specified and directed.

Supply and fixing in repair PVC SWR pipes 110 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and directed.

Supply and fixing in repair PVC SWR pipes 75 mm bore single socketed in any length with rubber joint fixed to wall or laid in trenches or in floor with steel clamps complete all as specified and directed.

Supply and fixing PVC SWR bends of 110 mm bore complete all as specified and directed.

Supply and fixing PVC SWR bends of 75 mm bore complete all as specified and directed.

Supply and fixing in repair PVC (SWR) junction double (double 'T') equal or unequal provided with access door of 110 mm dia complete all as specified and directed.

Supply and fixing in repair PVC (SWR) junction single (single 'T') equal or unequal provided with access door of 75 mm dia complete all as specified and directed.

Supply and fixing in repair PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed.

Supply and fixing PVC (SWR) reducer of 110 mm dia complete all as specified and directed.

Supply and fixing PVC (SWR) vent cowl 75 mm bore complete all as specified and directed.

Supply and fixing PVC (SWR) water closet connector with lip ring 110 mm complete all as specified and directed.

Supply and fixing in repair water closet Orissa pattern white with integral foot rest 580 x 440 mm including PCC bedding (1:2:4) and making good disturbed floor connecting to trap and flush pipe complete all as specified and directed.

Supply and fixing in repair PVC low level flushing cistern 10 litre capacity white with inlet ball valve, float valve and handle including brackets, PVC flush pipe complete all as specified and directed.

Supply and fixing in repair PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipes of 15 mm bore complete all as specified and directed.

Supply and fixing in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

Supply and fixing in repair tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges aluminium anodised, fixed with rawl plugs complete all as specified and directed.

Supply and fixing in repair bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed.

Supply and fixing in repair stop valve / angle valve cast copper chromium plated screwed down high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and directed.

Supply and fixing in repair brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore complete all as specified and directed.

Supply and fixing in repair stop valve cast copper chromium plated concealed type screwed down high pressure with capstan head suitable for 15 mm bore complete all as specified and directed.

Supply and fixing in repair stainless steel gratings of outer frame dia 150 mm openable type including all necessary fittings such as hinges including embedding in tiles with white cement complete all as specified and directed.

Supply and fixing 15 mm dia galvanised pipe medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply and fixing 20 mm dia galvanised pipe medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply and fixing 40 mm dia galvanised spout pipe medium grade for with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 15 mm dia old galvanised pipes including new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and directed. Note: - Serviceable pipe retrieved against Ser Item No 13.00 shall be used.

Fixing only 20 mm dia old galvanised pipes including new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and directed. Note: - Serviceable pipe retrieved against Ser Item No 14.00 shall be used.

Cutting chases for concealed water tubing or concealed conduit and making good in CM (1:3) of grith exceeding 10 cm and not exceeding 20 cm in brick wall complete all as specified and directed.

Material and labour for 75 mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection filled with mastic filling and 10 mm wide joints between the walls and plinth protectin shall be filled with mastic filling complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tank with float valve, plastic lid cover, double layered, cylindrical verticl with closed top hoisted and fixed in position of capacity 500 litre including making connections complete all as specified and directed.

Supply and fixing in repair stop valve 20 mm dia cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe and fixed complete all as specified and directed.

Material and labour for applying one coat of synthetic enamel paint tint over old painted steel surfaces over 10 cm in width or girth including preparation of old surfaces of steel complete all as specified and directed.

Material and labour for two coats of synthetic enamel paint tint after preparation of new surfaces of steel of any description, not exceeding 10cm in width or girth when unconnected with other painting or when painted in a different tint complete all as specified and directed.

Material and labour for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Material and labour for two coats of oil bound distemper of wall to newly plastered surfaces over chalk whitening including preparation of surfaces complete all as specified and directed.

Material and labour for one coat of oil bound distemper of wall to old plastered surfaces including preparation of surfaces complete all as specified and directed.

Material and labour for preparation of old plastered surfaces including filling of small holes etc and applying two coats of white wash on ceiling surface complete all as specified and as directed.

Material and labour for preparation of surfaces new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

Material and labour for two coats of cement based paint to newly plastered surfaces including preparation of surfaces and priming plastered surfaces with alkali resistant priming paint complete all as specified and directed.

Material and labour for one coat of cement based paint to old plastered surfaces including preparation of surfaces complete all as specified and directed.

Supply and fixing in repair stainless steel kitchen sink with drainage board made of stainless steel of 1 mm thick sheet including plugs, washers and PVC waste pipe of 40 mm dia fixing with complete on appropriate size of cantilever brackets of mild steel angle or GI pipe 15 mm dia with proper arrangement to hold and fitting of sink at site and connecting union to pipe. The overall size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply and fixing in repair stainless steel grade 430, glossy finish, wall hanging plate rack inclusive of spoon hanger, made out of 1mm thick sheet of size 750 x 600 x 250 mm having partition as per sample kept in AGE B/R office and fixed with steel fasteners or steel screwed complete all as specified and directed.

Material and Labour for cement concrete 50mm thick in (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in flooring finished even and rough complete all as specified and directed.

Material and Labour for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Material and Labour for machine pressed precast concrete interlocking paver block any shape and size confirming to IS : 15658-2006 of 60 mm thickness, M-35 grade with grey cement and no pigment complete all as specified and directed.

Material and Labour for preparation of surface, the surface must be sound and free from dirt, dust and loose particles, thoroughly wire brush the surface and clean the dust, wash the surface with water. Any damaged surface must be prepaired by using polymer modified repair mortar with Dr. Fixit Pidicrete URP. Clean the surface, saturated with water and remove the excess water if any and bring to touch dry state. Applying the first coat of mixed @ 0.75 Sqm / kg, 1mm thick for 2 coats) Dr Fixit Pidifin 2K on the prepared surface and allow it to dry for 4 to 6 hours. Prepare another batch of Dr Fixit Pidifin 2K and apply 2nd coat in direction 90 degree to first coat. Overlay protected screed using cement sand (1:3) along with Dr Fixit LW+ complete all as specified and as directed.

Material and Labour for cement concrete (1:5:10) type E-2 (using 40 mm graded crushed stone aggregate) as in sunken portion to receive floor toping as specified after carrying out the required tests of water proofing complete all as specified and directed.

Removing existing treatment from roof surfaces such as tiling, tarfelt, fungus, moss, dust etc., cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab removing the debris outside defence land complete all as specified and directed.

Material and labour for rendering 20 mm thick in CM (1:4) on fair face of brick work or concrete surfaces finished even and smooth without using extra cement up including mixing liquid water proofing compound complete all as specified and directed. Note: - Liquid water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and as directed.

Material and Labour for roof treatment with the folowing specification: - (a) Applying evenly one coat of bituminous primer conforming to IS 3384-1986 @ 0. 30 litres per Sqm over cleaned plastered surface. (b) Applying evenly one coat of blown hot bitumen of grade 85/25 @ 1.2 Kg per Sqm on primed surfaces. (c) Applying a layer of APP based Polymeric membrane 3mm thick (minimum) weighing 3.5 Kg per Sqm (reinforced) with polyster non woven fabric weighing not less than 160 gms per Sqm by torch application. The overlap shall be minimum 100 mm on traverce direction and 75 mm on longitudinal direction and sealing overlap by torch application. (d) Applying evenly one coat of Aluminium paint @ 0.10 litre per Sqm over the APP based polymeric membrane complete all as specified and directed.

Supply and fixing for 35 mm thick 2nd class hard wood plain framed, panelled shutter (two panel) of factory made with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing for 35 mm thick 2nd class hard wood factory made glazed and skeleton shutters open rebated and prepared to receive glass / wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass / wire mesh etc sizes of member as per clause 8.20(a) of SSR Part-I for door shutter complete all as specified and directed.

Material and labour for rendering 15 mm thick cement plaster in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces of wall and to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 75 to 100mm thick wide border of Makrana adanga white marble stone 18 to 20 mm thick laid over and including cement screed base 20 mm thick in cement mortar (1:3) and roughening the surface including cutting as required, rubbing and polishing complete all as specified and directed.

Supply and fixing in repair stainless steel drapery rods of 25 mm dia complete with conical end balls at both end, dia not less than 50mm and fitted with and including mild steel bracket size 150mm made to shape or 75mm dia mild steel end wall to wall round block made to shape in male and female pieces as required at site complete all as specified and directed.

E/M Portion: - Taking down old unserviceable copper / aluminium point wiring concealed / batten (light, fan, socket or power) complete including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Material and labour for point wiring for one light / fan / call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid / steel conduit and into existing CI / pressed steel sunken / terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and directed. Note: - (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engineer-in-Charge.

Description all as per Serial item No 120.00 here-in-before but for one 5 pin socket outlet 5 amps on the same board complete all as specified and directed.

Description all as per Serial item No 120.00 here-in-before but for one 5 pin socket outlet, 5 amps, independent complete all as specified and directed.

Description all as per Serial item No 120.00 here-in-before but for one 5 pin socket outlet 15 Amps on independent board with cables 2.5 Sqmm size complete all as specified and directed.

Supply and fixing in replacement for switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and directed.

Supply and fixing in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed.

Supply and fixing in replacement switch socket outlet combined 5 pin 5 amp flush type, 240 volts complete all as specified and directed.

Supply and fixing in replacement switch socket outlet combined 2 in 1, 3 pin 5 amp and 15 amp flush type, 240 volts complete all as specified and directed.

Material and labour in replacement for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour in replacement for self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and directed.

Supply and fixing in repair ceiling rose 3 terminal surface type complete all as specified and directed.

Supply and fixing in replacement LED lights fitting 1 x 20 W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen / Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and directed.

Material and labour for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in replacement 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB DB complete with connection, testing and commissioning complete all as specified and directed.

Supply and fixing in repair SPN 40 to 63 Amp rating 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection, testing and commissioning complete all as specified and directed.

Dismantling and taking down old unserviceable street / security lights and material and labour for new LED street light fittings of 30 watt system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, IP-66 protection suitable for pole mounting SMD LED array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W, 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V to 270 V, Power factor > 0.95, working temperature range - 20º C to 60º C, built in surge protection more than 10 KV with facility of power supply shall be removed without removing light fitting from pole including making proper connection complete including cutting, welding, drilling holes, nut bolts, washer complete all as specified and directed by Engineer-in-charge.

Material and labour in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 4.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the new rigid PVC concealed conduit fixed on wall. Two runs of cable for phase / neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and directed. Note: - Wiring shall be done in proper colour coding.

Material and labour in repair for earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick buried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 pre-cast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply and fixing in replacement plug top 15 Amps complete all as specified and directed.

Supply and fixing in repair TPN DB 125 Amps suitable for accommodating TPN miniature circuit breaker (MCB) 4 pole of following poles and current carrying capacity in the DB complete with connection, testing and commissioning complete all as specified and directed.

Supply and fixing in repair 415 V 10 KA 'B' curve TPN 40 to 100 Amp miniature circuit breaker (MCB) 4 poles and current carrying capacity in the DB complete with connection, testing and commissioning complete all as specified and directed.

Disconnecting and taking out defective service cable any size and any type from roof, pole, pipe, floor, wall etc complete all as specified and directed.

Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 Volts grade 10 Sqmm 2.0 core laid in trenches / on poles / road crossing or passing through existing / new pipe under road crossing, clamping on wall etc complete all as specified and directed. Note: - (i) Earth work, sand, bricks, removing, returning, filling in, Aluminium thimbles / lugs will be paid separately. (ii) Cost of laying electrical cable through new / existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying of electrical cable through new / existing pipes are to be provided by the contractor without any extra cost.

Supply and fixing in replacement of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - All plumbing works shall be laid or fixed as to be completely air tight or water tight as specified and Contractor will furnish its certificates towards air / water tight before completion of work under the Contract. NOTE NO 4: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

bushan kumar

M/S KARAN SINGH CONTRACTOR

STAR CONSTRUCTIONS

M/S MANJIT SINGH AND SONS

M/S BHAGMAL AND SONS

M/s Koul & Sons

Kanwal Nain Behl

Bidder Name

Kanwal Nain Behl

Shri Karshni Builders

STAR CONSTRUCTIONS

M/S MANJIT SINGH AND SONS

M/s Koul & Sons

bushan kumar

M/S KARAN SINGH CONTRACTOR

M/S BHAGMAL AND SONS