Tiruppur Corporation_Maintenance and Special Repair work Electrical Arrangements to Corporation Main Office Building in TCMC

Amount

Supplying and filling Well gravel in layers of not more than 15cm thick well rammed, watered and compacted etc., complete complying with standard specification.

Supplying and fixing in position of Aluminium anodised partition with 62x38x2mm extruded box section at bottom, vertical and horizontal members. The vertical members are spaced at 90cm c/c and to horizontal members are spaced at 1.20m, 2.10m and 2.40m height and the bottom panels should be covered with 12mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick clear glass with necessary glassing clips, rubber beadings etc., including cost of labour for electrical consumption required for the fabrication, drilling holes in RCC columns with power drill to the required extent and make good to the original condition etc., complete and as directed by the departmental officers. The aluminium for frame to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns.

Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish Single leaf door (with frame) half glazed and half PLB board using extruded aluminium section for frame and shutter with necessary accessories such as PLB 12mm thick, 5.50mm thick plain sheet glass, Alu. 'L' angles, Rubber beading, aluminium clips, best double action floor springs / door closer, handles, tower bolt, hinges, pivot and locks including labour and power consumption charges required for fabrication, if necessary chipping, dismantling, making necessary holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc., complete. The aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868 / 1962 of anodic film thickness of not less than 15 microns for all sections.

Supply and fixing FRP door shutter with frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of hold fasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., complete complying with standard specification.

Removing and Relaying of 63mm thick Rubber Moulded Hydraulic Pressed Paver Block in uniform shape of approved make to be laid including sweeping, loading and unloading etc., complete complying with standard specification

Providing Partition Wall arrangements on Exiting Partition Shiting Work including Labour charges Screw and Bolt Nuts for Removing and Refixing Charges etc., complete

Supplying and fixing in position of Steel Fibre Reinforced Concrete (SFRC) Manhole Cover of size 600mm x 600mm with best approved quality etc., complete as per standard specification.

Provision for Tree Branches Cutting and Removing to Existing Wall including Shuttering , Labour Charges etc., Complete

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3mm thick hylem sheet cover for 5A 3 pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 14 SWG TC wire with painting of suitable colour (SD 54)

Supply and fixing of single box type 4'36W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp with side plates and cross arm etc., Complete as per standard specifications (SD107)

Supply and Fixing of Lt 24W LED Backlight Panel sq 6K 2/2 LP48650 etc, complete as per standard specifications.

Supply and Fixing of Lt 48W LED Backlight Panel sq 6K 2/2 LP48650 etc, complete as per standard specifications.

Supply and Fixing of It 220 LED Armstrong Parabolic etc, complete as per standard specifications.

Supply and Fixing of Wip 20W LED Lamp D 622065 etc, complete as per standard specifications.

Add GST @ 18%

ULTRA TRADERS