Construction of 200 Bedded Civil Hospital at Sec 9 in Distt. Fatehabad (Pdg. 11 KV Substation, DG Set and Street/Security Lights Only).RECALL

Amount

[13.18]Providing and fixing hard drawn steel wire fabric 75 mm X 25 mm rectangular mesh with 3.25 mm dia wire fixed on steel windows of standard rolled sections with 3 mm thick flat iron cover moulding of 12.5 mm width fixed with machine screws welded complete in all respect. [Through Rate]

[13.2]Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. [Through Rate]

[20.62.2]Providing, lowering, laying, cutting (cut surface to be uniformly finished), jointing with rubber rings marked with IS : 5382 and testing of SPIGOT AND SOCKETTED RCC, NP2 MARKED WITH IS : 458-1988 and specials into trenches for all depths including carriage, loading, unloading, stacking, handling, re-handling etc. complete is all respects to the satisfaction to the Engineer - in -charge. 2. 250 mm i/d [Through Rate]

[20.84]Providing and fixing of insulated rubber matting suitable for 11 KV installation 1 M x 2 M x 12 mm thick (IS code 15652-40091) as per specification complete and as per directions of Engineer-in-charge [Through Rate]

[23.26.1]SAFETY ITEMS 1. Supply and erection of Medium Voltage caution notice plate of size 200*150 mm in three languages. [Through Rate]

[23.26.2]SAFETY ITEMS 2. Supply and erection of High Tension Voltage caution notice plate of size 250*200 mm in three languages. [Through Rate]

[23.26.4]SAFETY ITEMS 4. Supply & Erection of mild steel bucket stand suitable for 6 Nos. fire buckets,(but without bucket) including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 6x4 made of GI pipe 32mm dia). [Through Rate]

[23.27.1]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 1. M.S. pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embeded in 1:2:4 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level , having a base of size 900 mm x 600 mm x 250 mm below ground level. 0 0 [Through Rate]

[23.27.4]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 4. M.S. pedestal of size 900 mm wide , 1500 mm high , 450 mm deep and bottom totally open , duly embeded in cement concrete block of size 1050 mm x 600 mm x 200 mm above ground level ,having a base of size 1200 mm x 750 mm x 250 mm below ground level . 0 0 [Through Rate]

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate]

[24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate]

[24.1.3]EARTHING AND LIGHTENING ARRESTOR 3. Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. [Through Rate]

[24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. [Through Rate]

[24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. [Through Rate]

[24.1.7]EARTHING AND LIGHTENING ARRESTOR 7. Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required. [Through Rate]

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.1.9]EARTHING AND LIGHTENING ARRESTOR 9. Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth electrode as required. [Through Rate]

[24.11.54]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 54. 70 Sq mm 3.5 core (Arm.) [Through Rate]

[24.11.94]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 94. 300 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.) [Through Rate]

[24.13.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 32. 25 Sq mm 4 core (Arm.) [Through Rate]

[24.13.54]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 54. 70 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.70]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 70. 120 Sq mm 3.5 core (Arm.) [Through Rate]

[24.13.94]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 94. 300 Sq mm 3.5 core (Arm.) [Through Rate]

[24.14.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.) [Through Rate]

[24.14.46]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 46. 50 Sq mm 3.5core (Arm.) [Through Rate]

[24.14.70]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 70. 120 Sq mm 3.5 core (Arm.) [Through Rate]

[24.14.88]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 88. 240 Sq mm 3.5 core (Arm.) [Through Rate]

[24.14.93]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 93. 300 Sq mm 3.5 core (UnArm.) [Through Rate]

[24.15.3]HT CABLES (Aluminium Conductor, Armoured and Unarmoured) Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in 1 per meter below ground level with sand and bricks with all labour and material including digging and refilling of trench as required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 3. 70 Sq mm 3 core [Through Rate]

[24.15.5]HT CABLES (Aluminium Conductor, Armoured and Unarmoured) Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in 1 per meter below ground level with sand and bricks with all labour and material including digging and refilling of trench as required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 5. 120 Sq mm 3 core [Through Rate]

[24.16.3]HT CABLES (Aluminium Conductor, Armoured and Unarmoured) Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 3. Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 70 Sq mm 3 core [Through Rate]

[24.16.5]HT CABLES (Aluminium Conductor, Armoured and Unarmoured) Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 5. Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 120 Sq mm 3 core [Through Rate]

[24.2.7.3]LT CABLE 7.3. Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm Cable 2 to 4 Core [Through Rate]

[24.2.7.4]LT CABLE 7.4. Supply and erection of suitable compression type brass cable glands for underground Cable :- 70 sqmm to 95 sqmm Cable 3 to 3½ Core [Through Rate]

[24.2.7.5]LT CABLE 7.5. Supply and erection of suitable compression type brass cable glands for underground Cable :- 120 sqmm to 185 sqmm Cable 3 to 32 Core [Through Rate]

[24.2.7.6]LT CABLE 7.6. Supply and erection of suitable compression type brass cable glands for underground Cable :- 240 sqmm to Cable 3 to 32 Core [Through Rate]

[24.2.7.7]LT CABLE 7.7. Supply and erection of suitable compression type brass cable glands for underground Cable :- 300 sqmm to 400 sqmm Cable 3 to 3½ Core [Through Rate]

[24.2.8.10]LT CABLE 8.10. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 120 sqmm [Through Rate]

[24.2.8.11]LT CABLE 8.11. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 150 sqmm [Through Rate]

[24.2.8.13]LT CABLE 8.13. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 240 sqmm [Through Rate]

[24.2.8.14]LT CABLE 8.14. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work.300 sqmm [Through Rate]

[24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm [Through Rate]

[24.2.8.7]LT CABLE 8.7. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 50 sqmm [Through Rate]

[24.2.8.8]LT CABLE 8.8. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 70 sqmm [Through Rate]

[24.3.3.1]HT CABLE 3.1. Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm [Through Rate]

[24.3.4.1]HT CABLE 4.1. Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm [Through Rate]

[24.4.15.3]STREET LIGHT 15.3. B.S.E.N. 10025 High Masts "Supply, installation, testing and commissioning of 20 mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 nos. luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer -in-Charge Thickness of Top and Bottom Section = 3 mm & 4mm (minimum) Top Dia = 150 mm and Bottom Dia = 460mm Thickness of Galvanization - Top = 65 micron (minimum) and Bottom = 85 micron (minimum)" [Through Rate]

[24.4.2.3]STREET LIGHT 2.3. Supply and erection of GI bracket made of 32 mm dia medium class GI pipe, having 15 deg angle from horizontal, suitable for fixing on top of Street Light pole 120 cm long, with 30 cm high suitable size pole cap [Through Rate]

[24.4.6]STREET LIGHT 6. Supply and erection of Three Phase weather proof M.S. box of size 30 cm x 20 cm x 15 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 16 amp TP MCB and 4 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box and necessary connections. [Through Rate]

[24.4.8.5]STREET LIGHT 8.5. Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 7 Metre Long pole with top dia 75 0mm and bottom dia 150 mm with base plate of size 300 x 300 x 20 mm [Through Rate]

[24.5.1.1]MISCELLANEOUS ITEMS 1.1. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 1.5 sqmm [Through Rate]

[24.5.2.2]MISCELLANEOUS ITEMS 2.2. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 50/40 mm outer dia/ inner dia [Through Rate]

[24.5.2.5]MISCELLANEOUS ITEMS 2.5. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 120/105 mm outer dia/ inner dia [Through Rate]

[24.5.2.7]MISCELLANEOUS ITEMS 2.7. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 180/150 mm outer dia/ inner dia [Through Rate]

[24.7.5]RCC FOUNDATIONS FOR DG SET 5. 250 KVA DG Set [Through Rate]

[24.7.8]RCC FOUNDATIONS FOR DG SET 8. 750 KVA DG Set [Through Rate]

[24.7]RCC FOUNDATIONS FOR DG SET "Providing RCC foundation of M20 grade (1 Cement:1.5 Stone aggregate: 3 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 50 kg/cum of concrete contents, concrete cover 50mm, over a bed of 75mm thick PCC 1:5:10, of required dimensions as per OEM recommendations to provide levelled surface for placement of the DG set complete in all respects and as per directions of Engineer-in-charge (Size of foundation assumed = 5.0x1.8x1.0m)" Unit: per cum [Through Rate]

[24.8.2]RCC FOUNDATIONS FOR OCTAGONAL POLES 2. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 4m high pole [Through Rate]

[24.9.3]RCC FOUNDATIONS FOR HIGH MAST OCTAGONAL POLES 3. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 75 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for high mast octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 20m high mast pole [Through Rate]

[25.1.2]Supplying, fixing, testing and commissioning of condenser water pipes / non insulated chilled water pipes of following sizes of MS C class along with necessary clamps, vibration isolators and fittings such as bends, tees etc. but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. 2. 250 mm dia [Through Rate]

[25.2]Extra for Supplying and fixing of insulation on following nominal dia pipes with FR quality expanded polystyrene moulded pipe section of density 20 kg/cum after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500 g polythene faced hessian and then applying 0.6 mm aluminium sheet cladding complete with felt strip at joints repairing etc. as per specifications and as required complete in all respect.. [Through Rate]

S/I/T/C of DG exhaust pipe sport structure made of Angle iron 100x50x6 duly groted in RCC foundation (the design of structure will be got approved from structure design consultant before fabrication / installation) Complete structure duly painted in all respect including cost of foundation and erection. Make Tata / Jindal / SAIL (Rates are of GST excluded)

S/I/T/C of SS bellow for DG exhaust system 250 mm dia complete with necessary inlet and outlet connection duly sealed complete in all respect. (Rates are of GST excluded)

`Supply, Erection, testing and commissioning of Crompton/ Schneider / Siemens / Volt amp / Kirloskar make Transformer-2000 KVA 11/0.433 K. V.3 Phase-50 cycles copper wound outdoor type as per latest IS specification efficiency level 2 confirming to IS 1180 and IS 2026, duly laid on existing foundation at site of work, along with petty works required up to the entire satisfaction of the Engineer-in-charge of work as per detailed specification given as under: No. load voltage ratio 11/0.433 K V. No. of Phase = 3 Frequency cycles = 50HZ Type- double wound core type copper wound Cooling = ONAN Duty = Outdoor Vector group/ISS-DYN 11 Tapping on HV Compensation plus 5.0% To - 10% in steps of 2.50%. Temperature rise (oil/Res = 0C) 40/45 C Attitude= upto 1000metres above M.S.L. Fitting/Accessories Provided. Bucholez relay with alarm and trip contact. OFF LOAD TAP CHANGER Externally hand operated. Oil conservator with Filling hole and cap. Plain oil level gauge with minimum Level marking.` `Thermometer pocket 4Nos. plain roller uni directional OTI and WTI 1Nos dial type with alarm and trip contact. H.V Impulse with stand voltage (KV peak) 75 kvp. Silica-Gel Breather 1st Filling of oil. Drain cum filter value Rating and diagram plate Two earthing terminal Lifting arrangement Presure release walve / Air releases Plug, Explosion vent Diagram and rating plate Control cable: 1.5 sqmm copper of required cores from Bucholez relay, thermameter etc. including necessary connection up to RMU / ACB suitably laid with required protactive GI pipe etc. Termination: - HV=3 pole single glands Cable box suitable for reception of 1 no. 3 core up to 185 sqmm H.T.XLPE cable including cost of copper lugs/thimble. LT: 4 Pole cable box suitable for bus duct termination having extended copper bars of requisite capacity from L. T. bushing for making connection. LV: Neutral suitable cable box for earthing Provided. LT 4 pole cable box with terminal plate suitable for connecting 6 nos. 300mmsq x 3.5 c ore aluminium Armoured cable.(Rates are of GST excluded)`

Supply and erection of stay set with stay wire suitable for 9M long PCC pole made out of 7/3 SWG GI wire with U type M.S. Rod 5/8` dia duly threaded by means of angle iron of size 50 x 50 x 6 mm x 30 cm 6 feet long M.S. Rod buried in ground after fixing with cross channel size 75 x 40 x 6 mm x 60 cm long the stay wire will be binded on the top of the pole with help of suitable size of double U type M.S. Clamps and stay fixed with nuts and bolts the stay wire shall be insulated in the middle point with the help of egg insulator including all labour and material required to complete the job in all respect to the entire satisfaction of Engineer-in-charge of work.(Rates are of GST excluded)

Supply and Erection of fire buckets of 9 ltr. capacity made out of 24guage G.l sheet and duly painted with one coat of red oxide and 2 coats of approved paint in red colour and written with the fire` as per fire protection necessar sand filling in the bucket hung the bucket on stand with all labour and material required to complete the job all respect up to entire \satisfaction of the Engineer m charge of the work (Rates are of GST excluded)

Supplying, installation, testing and commissioning of following capacity terminal extension bus with copper bus bars having current density of 130 A/ sq cm at nominal current rating supply including jointing of sections, flexible joints, expansion joints, bends etc. duly insulated and fixed with transformer outgoings. (Rates are of GST excluded)

`Supply Erection Testing and Commissioning of 11kV indoor HT metering panel indoor / outdoor complete with C.Ts P.Ts Cubical .as per requirement / approved by DHBVNL consisting of the following. (Rates are of GST excluded) - Cubical panel free standing floor mounting type made out of sheet steel 16 SWG CRCA sheet with channel iron base frame spray painted with strong synthetic light grey enamel paint as per size and design approved by the DHBVNL. - 3 Nos. 11KV CTS of rating as approved by DHBVNL for indoor installation of approved make of DHBVNL. - 1 Nos. 11KVPTS 11000/10 VA burden 0.5 accuracy oil filled suitable for indoor installation of approved make of DHBVNL. The cubical panel will be completed in all respect including inter connection, internal wiring with PVC copper cable, modem and allied accessries its testing and approval of all item by DHBVNL cost of all testing/ approval charges or all items of DHBVNL with a guarantee of one year from the date of commissioning. including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the engineer in charge of the work (Rates are of GST excluded)`

Supply and erection of lighting arrestor model ALPRO / Alastem / LEMCO make suitable for 11KV 3 Phase 50 HZ ground neutral system comprising of spare gape type queen gap type in series with non linger resitar element house in Horizontally scale poreclam bushing with line and ground terminal along with mounting clamps conforming to ISS 3070 (Part-I) of 1985 with latest amendment with all labour and material required to the complete in all respect up to entire satisfaction of the Engineer-in-Charge of the works. (Rates are of GST excluded)

Providing and fixing earth bus of 50 mm x5 mm copper strip on surface for connection etc. as required. DSR 5.20 (Rates are of GST excluded)

`Supplying, installation, including suspension, testing and commissioning of following capacity bus trunking with aluminium bus bars having current density of 130 A/ sq cm at nominal current rating in 1.6mm thick IP 42 sheet steel enclosure in convenient sections for use on, 3 phase, 4 wire, 415 V, 50 Hz, A.C. supply including jointing of sections, flexible joints, expansion joints, bends and earthing with 2 runs of galvanised iron strips, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required DSR 3.5.5 1600 A (Rates are of GST excluded)`

S/E/T/C of 70W LED Street Light Luminaire Philips make BRP 501 R3c LED 98 or equilant in Bajaj / Surya / wipro suitable for working up to 50 degree Calcius, operating voltage range-140V - 270V Housed in pressure Die cast Aluminum alloy for housing (Heat-sink) for effective thermal management sturdiness and corrosion resistance IP66 protected covered tempered protective toughened glass, thermal shock and impact resistance, fix to the housing with SS screws having lumen efficacy of LED = 120 lm/W with Colour 5700K, PPC lens for uniformity inbuilt potted LED driver (SMPS based constant current supply) lower THD open circuit protection, over voltage protection, surge protection, and other safety test as per IS:15885 and BIS comply make complete the job in all respect up to the entire satisfaction of Engineer-in-charge of the work. (Rates are of GST excluded)

S/E/T/C of 350W LED Flood Light Luminaire Philips make BVP 485 LED 637 CWN or equilant in Bajaj / Surya / WIPRO suitable for working up to 50 degree Calcius, operating voltage range-140V - 270V Housed in pressure Die cast Aluminum alloy for housing (Heat-sink) for effective thermal management sturdiness and corrosion resistance IP66 protected covered tempered protective toughened glass, thermal shock and impact resistance, fix to the housing with SS screws having lumen efficacy of LED = 120 lm/W with Colour 5700K, PPC lens for uniformity inbuilt potted LED driver (SMPS based constant current supply) lower THD open circuit protection, over voltage protection, surge protection, and other safety test as per IS:15885 and BIS comply including S/E of suitable size of MS clamp bracket etc. complete the job in all respect up to the entire satisfaction of Engineer-in-charge of the work. (Rates are of GST excluded)

S/E/T/C of Post top Lantern Philips make BGP 300, Luminous Flux 2800 lm or equilant in Bajaj / Surya / WIPRO suitable for working up to 50 degree Calcius, operating voltage range-140V - 270V Housed in pressure Die cast Aluminum alloy for housing (Heat-sink) for effective thermal management sturdiness and corrosion resistance IP66 protected covered tempered protective toughened glass, thermal shock and impact resistance, fix to the housing with SS screws having lumen efficacy of LED = 110 lm/W with Colour 5700K, PPC lens for uniformity inbuilt potted LED driver (SMPS based constant current supply) lower THD open circuit protection, over voltage protection, surge protection, and other safety test as per IS:15885 and BIS comply make complete the job in all respect up to the entire satisfaction of Engineer-in-charge of the work. (Rates are of GST excluded)

Supply , fixing , connecting and testing of APFC Panel with IP42 200 KVAR @ 440V with 7% detuned reactor. The stage ratings shall be 1 X 5 KVAR plus 1X7.5 KVAr plus 1X 25 kVAr plus 3 X 50 KVAR, The APFC Panel shall be fully type tested and shall comply to IEC 61439-1 and2 . The APFC Panel shall be (Indoor) type, weather, dust and vermin proof suitable for humidity up to 95%. Average daily temperature: plus 35°C max, Ambient temperature: -5°C to 40°C, Maximum altitude: 1000 m. Make Dhillon Fabricators and Engineers / Sudhir/ Precision / Avon up to the entire satisfaction of Engineer in Charge As equipment shall be comprising of the following:- (A) Air Insulated bus bar assembly made from Aluminium and rated of 800 Amps capacity. The short circuit withstand capacity shall be 50 KA / 1 Sec ( Icw) for the main bus bar and the rated impulse withstand voltage shall be 6 KV. ( B) The incomer of the APFC Panel shall be a 630 Amp, MCCB, 3P, 50kA TMD type with O/L and S/C protection, Ics = 100% Icu, MCCB shall have standard extended rotary handle, spreaders, phase barrier. . Make:- Schneider Electric / ABB / Siemens (C) Capacitor Units : The capacitor unit shall be metalized polypropylene film with Zn / Al alloy. The capacitors shall be encapsulated in an aluminium can. The capacitor unit shall have a rated voltage of 440V and shall have a maximum over current capacity of : 1.8 In. The capacitor unit shall have a built in 3 phase over pressure protection and shall have discharge resistors ( 50V in 1min ) factory fitted and shall be tamper proof. Capacitance Tolerance -5%, plus 10%. Maximum permissible over voltage 1.1 x Un, 8 h every 24 h. The capacitor unit shall be of certified design confirming to IS-13340-1993,13341-1992. Make – Schneider Electric / ABB / Siemens `(D) Short-circuit and Overload Protection : Each stage of the APFC Panel shall have a suitably rated MCCB for short-circuit and overload protection. The over-current setting shall be adjustable and Breaking capacity Ics=) 36kA . The MCCB shall be of certified design confirming to IS Make:- Schneider Electric / ABB / Siemens ` (E) PF Regulator : Advanced Range PF Regulator shall have 8 steps with a LCD Display, Voltage Range : 90V - 550V, 50 / 60Hz, CT Input : 1A/5A with a built in RS 485 communication port. The PF Regulator shall be of certified design confirming to IS. Make : Schneider Electric / ABB / Siemens `(F) Stage Contactor and reactor : The electromagnetic contactors shall be rated for 660 Volts and shall be 3-pole type and shall be employed for switching `on` and switching `off` operations in capacitor banks. Supply to capacitor should be through 7% Aluminium wound detuned reactorThe rated voltage of control coil shall be 415V (phase-to-phase). This voltage is subject to a variation of ( plus ) 10% and (-) 15%. The contactor shall beCapacitor Duty Contactor AC6b type. The contactor shall be of certified design confirming to IS. Make – Schneider Electric / ABB / Siemens ` `(G) Ventilating fans of required size shall be sued to dissipate the heat produced by the capacitor bank components like the capacitor units, reactors, contactors, breakers etc. The capacitor banks should be of type tested design and temperature rise test report of the capacitor bank performed at an independent laboratory should be submitted along with the offer. (Rates are of GST Excluded.)`

Supply , fixing , connecting and testing of OEM Manufactured APFC Panel 650 KVAR @ 440V with 7% detuned reactor. The stage ratings shall be 1X5 KVAr, 1X 7.5 KVAr, 3 X 12.5 KVAR plus 4 X 25 kVAr plus 5 X 100 KVAR, The APFC Panel shall be fully type tested and shall comply to IEC 61439-1 and2 . The APFC Panel shall be (Indoor) type, weather, dust and vermin proof suitable for humidity up to 95%. Average daily temperature: plus 35°C max, Ambient temperature: -5°C to 40°C, Maximum altitude: 1000 m. Make Dhillon Fabricators and Engineers / Sudhir/ Precision / Avon up to the entire satisfaction of Engineer in Charge. As equipment shall be comprising of the following:- (A) Air Insulated bus bar assembly made from Aluminium and rated of 1200 Amps capacity. The short circuit withstand capacity shall be 50 KA / 1 Sec ( Icw) for the main bus bar and the rated impulse withstand voltage shall be 6 KV. ( B) The incomer of the APFC Panel shall be a 800 Amp, MCCB, 3P, 50kA TMD type with O/L and S/C protection, Ics = 100% Icu, MCCB shall have standard extended rotary handle, spreaders, phase barrier. . Make:- Schneider Electric / ABB / Siemens (C) Capacitor Units : The capacitor unit shall be metalized polypropylene film with Zn / Al alloy. The capacitors shall be encapsulated in an aluminium can. The capacitor unit shall have a rated voltage of 440V and shall have a maximum over current capacity of : 1.8 In. The capacitor unit shall have a built in 3 phase over pressure protection and shall have discharge resistors ( 50V in 1min ) factory fitted and shall be tamper proof. Capacitance Tolerance -5%, plus 10%. Maximum permissible over voltage 1.1 x Un, 8 h every 24 h. The capacitor unit shall be of certified design confirming to IS-13340-1993,13341-1992. Make – Schneider Electric / ABB / Siemens .`(D) Short-circuit and Overload Protection : Each stage of the APFC Panel shall have a suitably rated MCCB for short-circuit and overload protection. The over-current setting shall be adjustable and Breaking capacity Ics=) 36kA . The MCCB shall be of certified design confirming to IS Make:- Schneider Electric / ABB / Siemens . (E) PF Regulator : Advanced Range PF Regulator shall have 8 steps with a LCD Display, Voltage Range : 90V - 550V, 50 / 60Hz, CT Input : 1A/5A with a built in RS 485 communication port. The PF Regulator shall be of certified design confirming to IS. Make : Schneider Electric / ABB / Siemens . `(F) Stage Contactor and reactor : The electromagnetic contactors shall be rated for 660 Volts and shall be 3-pole type and shall be employed for switching `on` and switching `off` operations in capacitor banks. Supply to capacitor should be through 7% Aluminium wound detuned reactorThe rated voltage of control coil shall be 415V (phase-to-phase). This voltage is subject to a variation of ( plus ) 10% and (-) 15%. The contactor shall be Capacitor Duty as per AC6b type. The contactor shall be of certified design confirming to IS. Make – Schneider Electric / ABB / Siemens .` `(G) Ventilating fans of required size shall be sued to dissipate the heat produced by the capacitor bank components like the capacitor units, reactors, contactors, breakers etc. The capacitor banks should be of type tested design and temperature rise test report of the capacitor bank performed at an independent laboratory should be submitted along with the offer. (Rates are of GST Excluded.)`

Supply, installation, testing and commissioning of DG outgoing panel No.1 for Indoor cubical type suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel as per IEC 61439-1and2 with aluminum bus bar 800 A. The Panel shall have arrangement of connection with cables and to be installed on new suitable foundations with proper provision of incoming and outgoing LT Cables i/c providing following switch gears :-The switchboard shall be factory manufactured Panel shall have top and bottom Entry/Out going type. including Supply, Installation, testing and commissioning of Inert type Novec-1230/FM200 or equivalent Fire Detection Tube based Gas suppression system for electrical panel. It includes all the require accessories/equipments to complete the panel protection, as per detail specification Make Dhillon Fabricators and Engineers / Sudhir/ Precision / Avon up to the entire satisfaction of Engineer in Charge. Every Cable alley compartment of Panel shall have wired or wireless overheating sensors for cable with alarm system Approved Makes- MCCB/ switch gear = LandT, Schneider, Siemens, ABB. Incomer (From 750KVA DG AMF) 1000A 4 P Electrical operated ACB (a) 3 Nos.- RYB PHASE INDICATING LIGHT, 230V AC with each Incomer (b ) 3 Nos.-ON/OFF/TRIP INDICATING LIGHT, 230V AC with each Incomer(c) 3 Nos. CT FOR METERING, 1000/5A , CL-1.0, 15VA (d) 1 Nos. DIGITAL Multifunction Meter (IV,KW,KWH,KVA,PF,HZ Maximum Demand with LCD Display), 96mm square flush pattern with RS485 with each Incomer (e) CONTROL MCB, 2A SP, 10KA OUTGOINGS: `1 Nos. 800A FP MCCB Ics= 50kA thermal magnetic type with variable overload and Variable Short Circuit protection and EROM for main building light panel and lift. ` `4 No. 100A TP MCCB Ics=35kA thermal magnetic type (For MGPS, OT, Mortuary and spare)` `2 Nos. 32A FP MCCB Ics=35kA thermal magnetic type with variable overload and Fixed Short Circuit. (For ELV, Substation building) ` complete panel including all hardware, wiring termination etc., installed at site up to entire satification of engineer in charge. (Rates are of GST Excluded.)

Supply, installation, testing and commissioning of DG outgoing panel No.2 for Indoor cubical type suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel as per IEC 61439-1and2 with aluminum bus bar 800 A. The Panel shall have arrangement of connection with cables and to be installed on new suitable foundations with proper provision of incoming and outgoing LT Cables i/c providing following switch gears :-The switchboard shall be factory manufactured Panel shall have top and bottom Entry/Out going type. including Supply, Installation, testing and commissioning of Inert type Novec-1230/FM200 or equivalent Fire Detection Tube based Gas suppression system for electrical panel. It includes all the require accessories/equipments to complete the panel protection, as per detail specification Make Dhillon Fabricators and Engineers / Sudhir/ Precision / Avon up to the entire satisfaction of Engineer in Charge. Every Cable alley compartment of Panel shall have wired or wireless overheating sensors for cable with alarm system Approved Makes- MCCB/ switch gear = LandT, Schneider, Siemens, ABB. Incomer (From 750KVA DG AMF) 1000A 4 P Electrical operated ACB (a) 3 Nos.- RYB PHASE INDICATING LIGHT, 230V AC with each Incomer (b ) 3 Nos.-ON/OFF/TRIP INDICATING LIGHT, 230V AC with each Incomer(c) 3 Nos. CT FOR METERING, 1000/5A , CL-1.0, 15VA (d) 1 Nos. DIGITAL Multifunction Meter (IV,KW,KWH,KVA,PF,HZ Maximum Demand with LCD Display), 96mm square flush pattern with RS485 with each Incomer (e) CONTROL MCB, 2A SP, 10KA OUTGOINGS: `6 Nos. 200A FP MCCB Ics= 50kA thermal magnetic type with variable overload and Fixed Short Circuit and EROM (For Xray, blood bank, CT Scan / MRI, Ancilinator, ventilation panel, spare)` `1 No. 600A TP MCCB Ics=50kA thermal magnetic type (For AHU)` complete panel including all hardware, wiring termination etc., installed at site up to entire satification of engineer in charge. (Rates are of GST Excluded.)

Supply, installation, testing and commissioning of DG outgoing panel OPD block for Indoor cubical type suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel as per IEC 61439-1and2 with aluminum bus bar 800 A. The Panel shall have arrangement of connection with cables and to be installed on new suitable foundations with proper provision of incoming and outgoing LT Cables i/c providing following switch gears :-The switchboard shall be factory manufactured Panel shall have top and bottom Entry/Out going type. including Supply, Installation, testing and commissioning of Inert type Novec-1230/FM200 or equivalent Fire Detection Tube based Gas suppression system for electrical panel. It includes all the require accessories/equipments to complete the panel protection, as per detail specification Make Dhillon Fabricators and Engineers / Sudhir/ Precision / Avon up to the entire satisfaction of Engineer in Charge. Every Cable alley compartment of Panel shall have wired or wireless overheating sensors for cable with alarm system Approved Makes- MCCB/ switch gear = LandT, Schneider, Siemens, ABB. Incomer (From 250KVA DG AMF) 500A 4 P MCCB (a) 3 Nos.- RYB PHASE INDICATING LIGHT, 230V AC with each Incomer (b ) 3 Nos.-ON/OFF/TRIP INDICATING LIGHT, 230V AC with each Incomer (c) 3 Nos. CT FOR METERING, 500/5A , CL-1.0, 15VA (d) 1 Nos. DIGITAL Multifunction Meter (IV,KW,KWH,KVA,PF,HZ Maximum Demand with LCD Display), 96mm square flush pattern with RS485 with each Incomer (e) CONTROL MCB, 2A SP, 10KA OUTGOINGS: `1 Nos. 200A FP MCCB Ics= 50kA thermal magnetic type with variable overload and Fixed Short Circuit and EROM (For Light load)` `1 No. 100A TP MCCB Ics=50kA thermal magnetic type (For AHU)` `2 No. 63A TP MCCB Ics=50kA thermal magnetic type (For Ventilation and medical equipment)` complete panel including all hardware, wiring termination etc., installed at site up to entire satification of engineer in charge. (Rates are of GST Excluded.)

`Supply and erection of prestressed cement concrete pole as per IS : 1678-1960. 9 metres long 105 mm x 115 mm at top and 105 mm x 315 mm at bottom with working load of 200 Kg. burried 1.80 m in ground. (Make and specification as per DHBVNL) including Erection of RCC/ PCC pole of following length in brick ballast and ramming the foundation, finishing with 150mm thick cement concrete (1 :3:6) layer on top with including excavation and refilling etc as required (As per HSR 24.4.10.4.) Above 8.0 metre and up to 11.0 metre. (Rates are of GST Excluded.)`

`Supply and erection of ACSR conductor (ISI Marked) with accessories including stringing and sagging of conductor of various sizes as well as jointing and binding with insulator at support complete in all respect up to entire satisfaction of Engineer-in-charge of the work. ACSR Cond. 50 Sqmm (Make and specification as per DHBVNL). (Rates are of GST Excluded.)`

Supply, stringing and sagging of GSL wire 8 SWG complete in all respect with erection of the same upto the entire satisfaction of the Engineer in Charge of work (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and erection of MS channel 100x50x6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and erection of MS angle 50x50x6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and erection of MS flat 50x6mm including cutting bending to the required shape drilling hole carriage Painting loading unloading complete in all respect upto the entire satisfaction of Engineer-in-charge. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Providing and fixing of Nut and Bolt of size as per ISI specification of Engineer-in-charge. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and erections of V-shape X-arm on PCC poles as per state electricity Nigam design and requirement it should be made out of MS channel size 100x50mm 13.200 Kg complete in all respect . (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and erection of 11KV GI pin insulator with pin Rashtriya / Jayshree / BHEL make with pin with all labour and material required to the complete the job included the fixing the same on existing channels up to entire satisfaction of the Engineer-in-Charge of the works. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and erection of 11KV gang operated switch Rashtriya / Jayshree / BHEL make conforming to IS with latest amendment including suitable size of copper blade erection of same on the existing `H`pole with the help of 3 Nos. channels of size 75mmx40mmx6mm, 1.8M long fixed with suitable size of MS clamp, nuts and bolts including cost of 6 Nos. 11KV insulator with GI pin, RD fuses and painting with 2 coat of approved paint and one coat of red oxide material required to complete the job in all respect up to entire satisfaction of the Engineer-in-Charge of the works. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply and Erection of Digital Electronic Trivector Meter 3 phase 4 wires 0.5 accuracy for recording reading in KWH / KVARH / KVAH of make and rating approved by DHBVNL with push button display operating system for different kind of readings suitable for dual metering including cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the engineer in charge of the work. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

SITC of Disc insulator Rashtriya / Jayshree / BHEL make with Disc fitting TandC type complete in all respect with erection of the same upto the entire satisfaction of the Engineer in Charge of work (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Providing and fixing of 11 KV oil cooled CT/PT combined unit ratio 40/5 A.C 0.5 (5) VA 5 and PT ratio 11/110 volt AC 0.5 VA / 0 along with metering cubical etc. fixing on H. pole metering cubical wiring with plate form required to complete the job in all respect upto the entire satisfaction of the engineer in charge of the work as per approved make of DHBVN for dual metering. (Make and specification as per DHBVNL) (Rates are of GST Excluded.)

Supply, installation, testing and commissioning of Indoor cubical type main LT panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel as per IEC 61439-1and2 with Aluminium bus bar 4000 A. The Panel should be extendable type TTA of ABB (R2k), LandT (Ti), Schneider (Blokset), Siemens (Siepan), The Panel shall have arrangement of connection with cables and to be installed on new suitable foundations with proper provision of incoming and outgoing LT Cables i/c providing following switch gears :-The switchboard shall be factory manufactured Panel shall have top and bottom Entry/Out going type. including Supply, Installation, testing and commissioning of Inert type Novec-1230/FM200 or equivalent Fire Detection Tube based Gas suppression system for electrical panel. It includes all the require accessories/equipments to complete the panel protection, as per detail specification and as per direction of Engineer in Charge. Every Cable alley compartment of Panel shall have wired or wireless overheating sensors for cable with alarm system Approved Makes- ACB = LandT (Omega), Schneider(Masterpact NW), Siemens(3WJ), ABB(E Max2). Approved Makes- MCCB = LandT, Schneider, Siemens, ABB. Incomer (From Transformer-1) `1 No. 3200A FP EDO ACB Icw=55kA ,Microprcoessor based release with LSIG protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. ` METERING and INDICATION (a) 3 Nos.- RYB PHASE INDICATING LIGHT, 230V AC with each Incomer (b ) 3 Nos.-ON/OFF/TRIP INDICATING LIGHT, 230V AC with each Incomer (c) 3 Nos. CT FOR METERING, 3200/5A , CL-1.0, 15VA (d) 1 Nos. DIGITAL Multifunction Meter (IV,KW,KWH,KVA,PF,HZ Maximum Demand with LCD Display), 96mm square flush pattern with RS485 with each Incomer (e) CONTROL MCB, 2A SP, 10KA `Bus Bar Aluminium Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. as per Type Tested design of the Approved OEM` OUTGOINGS: `2 Nos. 1250A FP EDO ACB Icw=50kA ,Microprcoessor based release with LSIG protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. (For HVAC plant and spare) ` `1 Nos. 1000A FP EDO ACB Icw=50kA ,Microprcoessor based release with LSING protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter. (For DG-1) ` 2 Nos. 800A FP EDO ACB Icw=50kA ,Microprcoessor based release with LSING protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. (For APFC) `3 Nos. 250A FP MCCB Ics= 50kA thermal magnetic type with variable overload MCCB and Fixed Short Circuit protection and EROM (Xray, Medical equipment, CT scan, MRI, Spare) ` `2 Nos. 150A FP MCCB Ics= 50kA thermal magnetic type with variable overload and Fixed Short Circuit Protection and EROM (MGPS, OT) ` `5 Nos. 100A FP MCCB Ics= 50kA thermal magnetic type with variable overload and Fixed Short Circuit and EROM (Mortuary, Ancilinator, Tubwell, Sewage pump, ventilation panel) ` Bus Coupler `1 No. 3200A FP EDO ACB Icw=55kA ,Microprcoessor based release with LSIG protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. Copper Terminal adaptors on both side of ACB is reqd. ` Incomer (From Transformer-2) `1 No. 3200A FP EDO ACB Icw=55kA ,Microprcoessor based release with LSIG protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. Copper Terminal adaptors on both side of ACB is reqd. ` METERING and INDICATION (a) 3 Nos.- RYB PHASE INDICATING LIGHT, 230V AC with each Incomer (b ) 3 Nos.-ON/OFF/TRIP INDICATING LIGHT, 230V AC with each Incomer (c) 3 Nos. CT FOR METERING, 3200/5A , CL-1.0, 15VA (d) 1 Nos. DIGITAL Multifunction Meter (IV,KW,KWH,KVA,PF,HZ Maximum Demand with LCD Display), 96mm square flush pattern with RS485 with each Incomer (e) CONTROL MCB, 2A SP, 10KA OUTGOINGS: `2 Nos. 1250A FP EDO ACB Icw=50kA ,Microprcoessor based release with LSING protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. Copper Terminal adaptors on both side of ACB is reqd. (For Power load panel, HVAC AHU panel) ` `1 Nos. 1000A FP EDO ACB Icw=50kA ,Microprcoessor based release with LSIG protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. Copper Terminal adaptors on both side of ACB is reqd. (For DG-2) ` 1 Nos. 800A FP EDO ACB Icw=50kA ,Microprcoessor based release with LSIG protection along with variable current setting for L,S,I,G and variable time delay setting. Release with LCD Display for Current Parameter, Individual fault Indication. Copper Terminal adaptors on both side of ACB is reqd. (For APFC Tr-2) `6 Nos. 150A FP MCCB Ics= 50kA thermal magnetic type with variable overload and Fixed Short Circuit and EROM (MGPS alternate, OT alternate, CSSD, Laundary, Fire fighting, spare) WIRING and ACCESSORIES` Power and Control Wiring includinjg interlocking will be provided as per site requirement with (ISI 1100V) FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware and Labour etc. (Rates are of GST excluded)

Supply, installation, testing and commissioning of distribution network, 11 KV outdoor compact Sub Station totally factory assembled (non walk in type) consisting of 3 way RMU type, 1 No. 11KV/433V, 500 KVA Oil type transformer, 1 set of LT device as under. Make: Schneider, SIEMENS/ Voltamp/ Crompton (OEM Manufactured Only) `MV COMPARTMENT 11KV, 630A, 21KA/1Sec indoor type non-extensible, SF6 gas insulated Ring Main unit with sealed pressure system criterion in accordance with the IEC: 60298, 62271 - 202 manufactured by ABB, Schneider Electric and Siemens. RMU with Protection degree IP 54. IAC of 20 kA for 1 sec for tank and cable box category IAC-AFL . The Switchgear includes the following HV cubicles =1No.` `SF6 insulated switchgear (2 Isolator plus 1 Vacuum Circuit Breaker with metering): Qty-1 - SF6 insulated 400A/630A,21kA/1 s, Vacuum Circuit Breaker. The VCB should be able to clear at least 20 Nos Dead short circuit faults. - Integral earthing switch with making switch. - Emergency Trip Push Button - SF6 Gas pressure indicator. - 230V AC Shunt Trip coil for external trip signal. - Live cable indicating LEDs energized thru capacitive voltage dividers. - Cable box suitable for termination of 1no. 3CX300sq.mm. PILC/XLPE cable.` `Right angle terminal protects/boots. - Padlocking facility. - Microprocessor based IDMT relay for overcurrent, short circuit and earth fault protection RMU metering compartment shall be provided with potential transformer rated for 11v3/110v3, 50 VA for metering purpose having class 0.5 accuracy RMU shall be provided with metering and protection CTs rated for 50 / 1 plus 1amps, class - 0.5 accuracy, 2.5 VA burden for circuit breaker 1 No. Trafo card` Transformer Oil Type Three phase, Ester Oil type transformer. Make : Crompton/ Schneider / Voltamp / Siemens i) efficiency level 2 Standard: IS : 2026, IS 1180 part 1 ii) Indoor Installation, iii) Vector group : Dyn11 iv) Rating : 500 KVA v) Cooling System: ON, v) Winding: Copper, vi) Magnetic Core: Prime grade of M4 or better vii) High voltage : 11KV - 50 Z, viii) Low voltage: 415V-50HZ ix) System highest voltage : 12kV at the HV side x). xi) Insulation Level `H.V. Power Frequency (KV rms): 28 kV - H.V. Impulse withstand voltage (KV peak): 75 kVp. The Losses of Transformer should be as per IS 1180 part 1 norms. Transformers shall be designed for 110% continuous over fluxing withstand capability Tapping: as per IS 1180 part 1 Temperature : - Ambient temperature: as per 40 Degree C. - Winding temperature rise: 45 Degree C. Accessories: - OTI and WTI, Pressure relief valve (without auxiliary contacts),Skids, Earthing terminal, Lifting lugs, Rating plate, Dehydrating breather, Jacking Lugs (Transformers weighing above 3000 Kg),vent with diaphragm =1No.` `LV COMPARTMENT The LV compartment with Degree of protection-IP54 designed for a 50 degree C ambient temperature. The panel is modular, dead front, freestanding, floor mounted and comprises the following equipment: INCOMER. • 433 V air insulated Aluminium busbar having capacity 800A, 50Hz,50KA withstand fault level capacity, MFM - EM6400NG/ 7KT0310 in incomer • 1No. 4 pole, 800A, 50KA manually electrical operated type ACB with inbuilt microprocessor based trip system Overload, SC, Inst. and E/F, U/V protection with current metering display with Thermal memory. Suitability for isolation as per IEC 60947-2.ACB should have LCD display. Tripping time (30 sec. Fault differentiation on release of ACB respective LED glows, indicating the type of fault. Aux contact - 4 NO plus 4 NC. release. Icu=Ics=Icw = 50 kA (1 sec) .(Masterpact NW) - Schneider ,(3WJ)-Siemens , ( U-power MTX 3.5 EC) - LandT) ` OUTGOING: All the the MCCB should be Thermal Magnetic based , Variable Overload protection setting type with Icu = 100% Ics as per IEC 60947-2, suitable for isolation with class 2 front face MCCB 4 Pole, 630A , 50 kA =1Nos. (APFC) MCCB 4 Pole, 250A , 35kA =5Nos. (Metering panel) MCCB 4 Pole, 100A , 35kA =4No. (Metering panel) Outdoor Enclosure :- The enclosure shall be made of 2.0 mm thickness Galvanized Sheet Steel tropicalised to meet Indian weather conditions including all the partition sheets and doors. The base of the enclosure shall be of 4.0 mm thickness Hot Dip Galvanized Sheet Steel to ensure rigidity for easy transport and installation. The entire Package Substation shall be Factory Assemble and Factory Fitted. The enclosure shall have IP54 degree of protection for HT and LT switchgear compartment IP 23 degree of protection for Transformer compartment. The Enclosure to be tested for Internal Arc fault test to the tune of at least 20 KA for 1 second adhering to as per latest IEC 62271-202.The temperature rise test on enclosure for K10class.The enclosure exterior shall be powder courted. Each compartment will be provided with door and pad locking arrangement. The compartment illumination lamp with door operated switch shall be provided for MV and LV compartment. (Rates are of GST excluded)

Supply and erection of Decorative pole made of galvanized Mild Steel Pipes fitted with cast aluminum embellishments duly polyurethane painted coated 4 Mtr Hight with adopter plate 250x250x12 mm MFMD-108A Model or equivalent Polux/ Havell`s/ Keselec/ Bajaj complete with all accessories and labour to complete the job upto the entire satisfaction of Engineer-in-charge of the work. (Rates are of GST Excluded.)

J D B POWER PROJECTS (BID ID -1392314)