PROVN OF STORE ROOM AT HQ RTG ZONE AT SHILLONG AND PROVISION OF CERTAIN ADDN/ALTN INCL TILING REPLACEMENT OF JOINERIES WALL PANELLING AND IMPROVEMENT OF DRAINAGE SYSTEM WITH MS DRAIN COVERS AT STN CELL HQ 101 AREA AND SPL REPAIR OF QTR NO 142/07 AND

Amount

B/R Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointing in any mortar complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), emoving serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for non skid ceramic coloured tiles Edge cut 7 to 8 mm thick (Square/rectingular)area of each tiles exceeding 0.11 Sqm (400 x 400mm) but not exceeding 0.18 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to 15mm thick screed bed 1:6 cement motar complete all as specified and directed match complete all as specified and as directed.

M & L for colour glazed ceremic coloured tiles in vertical surface 300 x 600 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering of cement mortar 1:4 cement complete all as specified or as directed.

M&L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchand witn 15mm thick screed bed 1:6 cement motar complete all as specified and as directed

All as per Item No. 06 above but as in vertical surfaces including rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified and as directed.

Demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs and stair case similar work carefully and matching to adjoining disturbed surfaces complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in slab, shelves and stair case etc. complete all as specified and as directed. .

M&L RCC type B 1, 1:2:4 (20mm graded agg) as in beams, cantilevers, lintels, over 1.5 m span complete all as specified and as directed.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as as in chajjas and like complete all as specified and as directed.

M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and as directed.

S&F TMT bars 8 to12mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S&F deformed or twisted bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia complete all as specified and as directed.

M&L Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and as directed.

M & L formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified and as directed.

M & L formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified and as directed.

M&L for Marble works 18-20mm thick Green marble machine cut and machine polished,and moulding, one side green marble, over/jambs of doors/ window cills, riser of steps and urinal partition wash basin platforms and flooring,skirting/dados like in cement mortar(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble complete all as specified and as directed.

Taking down chowkats with shutters not exc 1.5 Sq.m each including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and as directed.

Taking down chowkats with shutters exc 1.5 Sq.m each and not exc. 4.00 Sq.m including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and as directed.

Taking down shutter of any description exc 1 sqm and n exc 2 sqm each complete all as specified and as directed.

Taking down shutter of any description exc 2 sqm each complete all as specified and as directed.

S&F mild steel framed work such as grills grating etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars, barrel iron doors ladders framed balusters walk ways railing frame work of water tanks and similar work confirming to Fe -290 Gde-E-165 complete all as specified and as directed.

M&L providing "RAJSHRI" BRAND FACTORY MADE PVC INTERNAL DOOR FRAME (PRELAM) of size 100 mm x 45 mm with a wall thickness of 5 mm (+- 0.25 mm ) made out of extruded 5 mm (+- 0.25 mm ) thick PVC sheet manufactured by an ISO 9001-2008 certified company and by joining 3 nos Heat bent PVC sheet sections. the inside section of size 90x30 mm shall be made from plain colour PVC sheet of 5 mm (+-0.25 mm ) thickness the inside section will be covered by sticking two sections of size 30 x 35 mm and 70 x 45 mm made from (+-0.25) thick plain PVC sheet The frame shall be mitre cut at two corners and joined with 4 nos of 150 mm long brackets of 15 mm x 15 mm MS square tube The two vertical door frames are to be reinforced with 40 mm x 20 mm MS tubes of 19 guage through out the farme The door frame shall be fixed to the wall using 8/100 mm long screw through the frame by using anchor fastners. A minimum of 4 nos screw to be provided for each vertical members and minimum 2 nos for horizontal member etc complete all as specified and as directed of engineers-in-charge

M&L in providing 30 mm thick RAJSRI brand factory made internal PVC flush door shutter wood free consisting of frame made out of M S tubes of 19 guage thickness and size 20 mm x 40 mm for siles as well as top bottom and lock rail MS frame shall have a coat of metal primer of approved make and manufacturer. The inside panel shall consist of 20 mm thick multichamber hollow PVC section 1 mm wall thickness bonded using solvent cement/ cynoacrylate adhesive with 5 mm (+-0.25 mm) thick plain/prelam PVC sheet manufactured by an ISO-9001-2008 certified company on both side of the inside panel All the four edge of the panel to be sealed with lipping of 10 mm thick and 20 mm wide PVC sheet baton( made by sticking 2 nOs PVC sheet of 5 mm ( +0.25 mm ) thickness using PVC solvent cement adhesive Door edge lipping to be painted with PVC ink of matching colour of plain/prelam moulded PVC sheet of door 0.20 mm thick ( 5mm x 4 mm) thick PVC sheet to be given for lock provision at lock height. Door to be fixed with frame with 3 nos stainless steel butt hinges of size 100 mm * 25 mm * 25 mm and 50 mm long steel screws drilled suitable to pass through both the wall of the MS tube other hardwares should be fixed with 25 mm * 8mm size steel screws etc complete all as specified and as directed of engineer-in-charge, manufacturers specification and drawing

S&F for 100mm long stainless steel butt hinges for PVC door/cub board complete all as specified and as directed.

S&F for 150mm long aluminum anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F for 150mm long aluminum handles, cast type complete all as specified and as directed.

S&F125x60mmx2mm thick pressed steel, frames for door with one or more rebates including filing and compaction with PCC 1:3:6 Type C1, necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed.

S&F105x60mmx2mm thick pressed steel, frames for door with one or more rebates including filing and compaction with PCC 1:3:6 Type C1 necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed.

S&F 40 mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified and as directed.

M & L for 35mm thick plain framed glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, without sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc, of 2nd class hard wood , members of shutters as specified in SSR Part - I Section 8 clause 8.24 (a) fitted to chowkats complete all as specified and as directed.

M&L Preparation of old wooden surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L painting to wood and wood based surfaces of any description exc 10cm with or girth with two coats of synthetic enamel paint over a coat of pink primer including preparation of new or previously untreated surface complete all as specified and as directed.

M & L preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for painting to steel surface exc 10 cm width or girth with two coats of synethic enamel paint over a coat of red oxide primer including preparation of newly or previously untreated surface complete all as specified and as directed.

S&F for 200mm long aluminum anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F for 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 300mm long mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F sheet glass 5.5mm thick ordinary quality and glazing with oil putty in square exc 0.5 Sqm each pane complete all as specified and as directed.

S&F sheet figured glass 5mm thick ordinary quality and glazing with oil putty in square exc 0.5 Sqm each pane complete all as specified and as directed.

S&F galvanised Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and as directed.

S & F 300 mm size, MS ordinary rat tail rod pattern springs including roller and roller plate complete including fixed to wooden and steel chowkats complete all as specified and as directed.

M&L 15mm thick cement plaster on brick surfaces or concrete surfaces in cm (1:4) including taking down plaster finishing the surface even and smooth without using extra cementand necessary scaffolding complete all as specified and as directed.

M&L 15mm thick cement plaster on brick surfaces or concrete surfaces in cm (1:6) including taking down plaster finishing the surface even and smooth without using extra cement and necessary scaffolding complete all as specified and as directed.

M & L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) finished including taking down plaster the surface even and smooth without using extra cemen tand necessary scaffolding complete all as specified and as directed.

M&L white washing three coats to wall surfaces including preparation of newly plastered untreated surfaces and necessary scaffolding complete all as specified and as directed.

M&L white washing three coats to CEILIING surfaces including preparation of newly plastered untreated surfaces and necessary scaffolding complete all as specified and as directed.

Complete removal of existing treatment from wall/ ceiling surfaces and rubbing down with sand paper to have even and smooth surfaces complete all as specified and as directed.

M&L for applying 1 mm thick layer of birla wall care putty on wall/ceiling surfaces incl rubbing down the surfaces with sand paper after getting dried all as directed to obtain a smooth & even surface complete all as specified and as directed.

M&L Preparation of old decorated surfaces and applying one coat of white wash on ceilings complete all as specified and as directed by Engr-in-Charge.

M & L applying two coat of distemper oil emulsion white or tinted on newly decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified and as directed.

M & L applying two coat of distemper oil emulsion white or tinted on old decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified and as directed.

M & L applying one coat of weather coat exterior paint on old decorated or undecorated wall, roof surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified and as directed.

M&L Two coats of weather coat exterior paint on new plastered wall surfaces over a coat of primer of any description including preparation of surfaces, complete all as specified and as directed.

S&F in repair Vitreous China, semi-pedestal pattern (Anglo-Indian Type) including connections to flushing cistern/pipe complete all as specified and as directed.

S&F in repairs plastic water closet white seat cover for Anglo indian type pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed.

S&F in repair 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repair stop valve/angle cock two/one way 15mm dia, fancy chromium plated, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union and fixed complete all as specified and as directed.

S&F in repairs chromium plated fancy type long body bib taps with cast copper alloy screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore pipe complete all as specified and as directed. Make Jaguar/Parryware

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts complete all as specified and as directed.

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

S&F for 15mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

S&F for 20mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified or as directed.

Dismantling water tanks and removing to store capacity exc 250 and not exc. 500 litres complete all as specified and as directed.

S & F 500 ltrs capacity rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.

S&F 15mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified or as directed.

Taking up or down AC/PVC rain water pipe, soil/waste/vent pipe of any size with fittings etc. complete all as specified and as directed.

S & F PVC (SWR) 110 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall complete all as specified and as directed.

S & F sand cast iron soil, waste and vent pipe, 75mm bore, in any length with or without ear with cement joint fixed to walls complete all as specified and as directed.

M & L 75 mm dia cast Iron Nahani trap with CP grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) as in repairs complete all as specified and as directed.

S&F 100mm bore CI soil waste / vent pipe (spun type) in any length with or without ears with cement joint to wall with stack clamps out of 110mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing end of stays to wall or roof etc.all as specified including black japan paints Make neco complete all as specified and as directed.

S&F 75 mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and as directed.

S&F CI 75 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and as directed.

S&F 100mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and as directed.

S&F CI 100mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and as directed.

S & F PVC (SWR) 110 mm bore bends complete all as specified and as directed.

S & F PVC (SWR) 75 mm bore bends complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, aches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

M&L old brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in cm (1:6) complete all as specified and as directed.

M&L old brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cm (1:4) complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove complete all as specified and as directed.

Demolition of cement concrete(unreinforced), in any position and paving n.exc. 15 cm thickness( below or above ground level) including tile/ terrazzo floor complete all as specified and as directed.

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified and as directed.

Supply only liquid waterproofing compound complete all as specified and as directed. Make : Dr. Fixit

M&L for cement concrete type E2 1:5:10 (40 mm graded aggregate) as in mass concrete complete all as specified and as directed.

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate as in levelling course, haunching, coping and similar works of over RCC roof surface including rounded or chamferred on edges etc complete all as specified and as directed.

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

M&L 25mm thick cement concrete type B1 1:2:4 using 20mm graded stone aggregate in floor finishes even and fair to receive floor tiles complete all as specified and as directed.

Supply and providing water proofing treatment with polymeric standard water proofing membrane, Aquaflex manufactured by M/s Bengal Bitumen,MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness all as specified and directed and described as under :- (a) Prepartion of RCC foof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/Sqm including cleaning surface, all as per manufacture'"s specification complete all as specified and directed. (b) Supply & providing water proofing treatment with polymeric proofing membrane of 3 Kg/Sqm HYPERPLAS STANDARD/MULTIPLAS STANDARD consting of 100 micron HMHDPE film centre core including coating he surface with the compatible primer and torch application of membrane with 10 cm overlaps as required thereof, complete all as specified or as directed.

S&F stainless steel grating fixed in repairs complete all as specified and as directed.

S&F towel rail cast copper alloy, chromium plated 600mm long in repair & dia of 20mm complete all as specified and as directed.

S & F stainless steel plate rack not less than 5 Kg of size in repair complete all as specified and as directed (Model : KPR -315 of M/S Blue Star or equivalent make- of M/S Jain Brothers sanitation Pvt Ltd Brand -Jayna)

S&F in repairs vitreous china coloured wash hand basin with pedestal of size 55X45X82cm complete including brass CP Waste (coupling) fittings with long screwed shanks and fly-nuts, flange end bedded in red lead cement and including brass CP trap 'P' or 'S' pattern for wash basins and sinks with inlet and outlet, screwed for pipe or connections, with one cleaning cap, 32 mm dia and also including 32mm dia waste pipe, complete fixing arrangement and cutting for and pinning in ends of bracket in walls & making good complete all as specifed and as directed by Eng in charge.Model : WHB - Cat No 10072, Pedestal- Cat No. Ped 11029 Neptune of Hindware ,Parryware Cat No C0480 (SP) 181/CTH ,C 0375 pedestral, Cera Cat No 2090107Ped , Cat No S 2040112 WHB

S & F in repair chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union size 125 mm complete Model No: F 7010305 of Cera , Hindware Model No F160006 , Parryware Model No T9985 A1 complete all as specified and as directed.

S&F in repairs 15mm dia chromium plated wall mixture with connection for shower arragement complete all as specified and as directed.

S&F in repairs hand shower (health faucet) 1 mtr PVC tube with wall hook complete for ETWC complete all as specified and as directed.

S&F in repairs PVC toilet cabinet with mirror of size 20"X16" of selecred quality complete all as specified and as directed.

S&F in repairs 75 mm x 32 mm dia chromium plated waste fitting special size suitable for stainless steel sinks including PVC flexible waste pipe of approved quality complete all as specified and as directed.

S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repair of PVC corner set of three of size (12'X12" ,9"X9" and 6" X6" ) with railling and complete all as specified and as directed.

S&F 18 to 20 mm thick granite stone slabs mirror polished of colour and shade as approved by GE, machine cut bedded & jointed with grey cement slurry and pointed in white cement with admixture of pigment to match the shade of granite stone fixed as in steps, jambs, pillars window cills, cooking platforms & the like etc complete all as specified and as directed

Rounding to edges of stone slabs one edge , such as in steps , cooking platform , and other similar situations complete all as specified and as directed

M & L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection 75 mm thick finished even and fair complete all as specified and as directed.

M & L for Plain Cement Concrete 1:3:6 type C-1 as in bed blocks for hold fast and similar work etc complete all as specified and as directed.

M&L for hard core of stone not exc 63 mm guage spread, levelled in layers not exc 100mm watering and well ramming to true surfaces complete all as specified and as directed.

M & L 75mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and as directed.

M& L providing precast cement concrete rubber moulded coloured interlocking tiles 60 mm thick with grey cement and pigment of approved design and pattern laid over a layer of 25 mm thick sand cushion including filling the joint with sand complete all as specified and as directed.

M&L providing cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in benching, coping, bed blocks including necessary form work, weathering slightly rounded or chamfered angles and throating, complete all as specified and as directed by Engineer-in-charge.

S&F in repairs centre hole basin mixture 15 mm dia chromium plated complete all as specified and as directed.

S&F in repairs sink mixture 15 mm dia chromium plated complete all as specified and as directed.

M&L for 15 mm thick redering on fair faces of concrete surfaces in CM 1:4 with water proofing compound incl demo of old plaster on concrete surface complete all as specified and as directed.(NOTE:- WPC shall be measured and paid separatly)

S&F low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls complete all as specified and as directed.

S&F Stainless steel Curtain Rod 25 mm dia of approved quality with two number decorative design as approved brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod complete all as specified and as directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs factory made PVC cupboards frame of the size 75 mm x 40 mm with a wall thicknesss of 5 mm made out of extruded 5mm thick plain/prelam PVC sheet of density 600kg/cbm, having bottom width of 50mm and thickness of 10 mm. All four frame lengths reinforced with 15 mm x 15mm M.S.square tubes of 19 quage thickness throughout the frame and mitre cut at two corners adjointed with 2 nos of 15mm long brackets of 10 mm x 10 mm M.S. square tubes. the door frame shall be fixed to the wall using 8/100 long MS screw through the frame by using PVC fastners. A minimum of 4 nos of screws to be provided for each vertical members and minimum of 2 nos of screw to be provided horizontal members etc. complete all as specified and as directed of Engr-in-charge, manufacturer's specification and drawing.

S&F factory made PVC cupboards flush type shutter of 30 mm thick consisting of frame made out M S tubes of 19 guage thickness and size 19mm x 19 mm for stiles and rails. The inside panels shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement / cynoacrylate adhesive with 5mm thick plain/prelam PVC sheet, on both sides of inside panels including necessary item to fix the shutters to frame such as 100 mm stainless steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutters. all four edges of the panels to be sealed with lipping of 10 mm thick and 20 mm wide PVC sheet baton( made by sticking 2nos PVC foam sheet of 5mm thickness using PVC solvent cement adhesive)complete all as specified and as directed of Engr-in- charge

S&F in repairs PVC boards 19/20 mm thick any colour as in cabinets incl shelves and shutters, fixed with screws and adhesives as per direction of engr-in-charge and manufacturers instructions including piano hinges , magnet catcher, handles etc complete all as specified and as directed.

Cleaning of roof/ walls of buildings ( area n exec 100 sqm) including complete removal plants grown with roots and treated with lime and filling the hole properly by cement mortar 1:3 complete all as specified and as directed.

S&F in repais Block boards 18/19mm thick interior grade commercial type on both sides of required size in kitchen baskets incl lamination with 1mm thick sun mica sheets on both sides and edges all round covered with PVC coloured tapes, of approved colour complete all as specified and as directed.

S&F Anodised aluminium frame for doors windows, ventilators and kitchen cupboards frame with one or more rebates including joining cleat for fixing etc. complete all as specified add for powder coating (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F for Powder coating Anodised aluminium window and ventilator shutters, side hung /sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F in 6mm thick bakelite hylam sheet of any colour or shade complete all as specified and as directed.

M&L Peg set of six Aluminium alloy body complete all as specifed and as directed.

S & F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in floor complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre ,Pulp,insulation ,etc)or insulation boards /slabs/blankets ,any thickness,including cover fillets complete all as specified and as directed.

S&F GI frame work for snap grid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Aluminium main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mm c/c using Gi wire of 4mm thickness Aluminium frame will be 60 x 60 cm to recieve ceiling board complete all as specified and as directed .

M&L for 4mm thick non asbestos fiber cement building E boards 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any guage, thickness incl nainital or similar pattern as in roof coverings complete all as specified and as directed.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and as directed.

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and as directed

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in soft/loose soil, complete all as specified and as directed.

Excavating over areas, n. exc 1.5 m deep and getting out soft/disintegrated rock complete all as specified and as directed.

Returning, filling in, including, spreading, leveling, watering and well ramming in layers n.exc 25cm complete all as specified and as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and as directed.

M & L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M & L PCC 1:4:8 type D2 (using 40 mm graded aggregate) as in Foundation filling and mass concrete complete all as specified and as directed.

M&L RCC 1:1.5:3 (Nominal mix) using (20mm graded aggregates ) as in fondation, footing, Plinth beam complete all as specified and as directed.

M&L RCC 1:1.5:3 (Nominal mix) using (20mm graded aggregates ) as in columns, pillars etc complete all as specified and as directed.

M&L RCC 1:1.5:3 (Nominal mix) using (20mm graded aggregates ) as in beam, lintel band over 1.50m span complete all as specified and as directed.

Use & waste of formwork to sides of concrete foundations,footings, bases of columns, plinth beams and similar work with rough finish surfaces of concrete flat complete all as specified and as directed.

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finish surfaces of concrete, Square, rectangular or polygonal in shape complete all as specified and as directed.

Use & waste of formwork to sides and soffits of floor or roof beam , lintels , cantilevers , shelves including supports , overhangs etc. also splays between floors and beams etc. of with rough finish surfaces of concrete flat complete all as specified and as directed.

S&F Steel work in tublar trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade ST-240 complete all as specified and as directed.

S&F 2nd class soft wood plain soild, stright chowkats and frames, wrought, framed rebated on thes olid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 30 mm thick 2nd class hard wood flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

S&F Aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) 300mm size and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm complete all as specified and as directed.

S&F aluminium anodised barrel bolts and fixed of 200 mm length complete all as specified and as directed.

M&L 4.80 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pan complete all as specified and as directed.

M&L for precast cement concrete block masonry with solid blocks exc 10 cm in width with PCC (1:3:6), type C-1, (using 20mm graded stone aggregate) and setting in CM(1:6) complete all as specified and as directed.

M&L for Rendering 15mm thick on fair faces of concrete surface of wall in CM (1:4) finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral water proofing compound complete all as specified and as directed.

M&L for 15mm rendering in cement mortar (1:6) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489:2004, Alkali & fungal resitance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surface on new or previously untreated surfaces complete all as specified and as directed.

M&L for earth filling (excavation over area) speading and leveling in layer n.exc 25 cm and well ramming including watering complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab as in steps, skirting, dado and pillars including rubbing and pollishing complete including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L walling of Random rubble , uncoursed, polygonal rubble walling brought up to course built in cement mortar 1:4 complete all as specified and as directed.

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggregates) including necessary form works as I precast bond stone set in CM 1:6 complete all as specified and as directed.

Extra over Hammer dressing with maximum depression on face from straight edge held against the dressed surface n, exc 20mm complete all as specified and as directed.

M&L raised pointing to random rubble stone masonary uncoursed or brought upto course in cement mortar 1:3 complete all as specified and as directed.

Dismantling of timber scantling 40 sqcm over in section in any position (unframed work) complete all as specified and as directed.

M&L for wrought second class hard wood in scantlings framed and fixed complete all as specified and as directed.

M&L for 2nd class hard wood Plain fillets square , rectangular or triangular in section , clean swan secured with nails sectional area exc 13 sqcm and n exc 25 sqcm complete all as specified and as directed.

S&F in repair 4mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and as directed.

M&L for prepartion of new or previously untreated surface of wood/plywood and applying two coats of varnish of any description, over 10cm in width or girth complete all as specified and as directed.

S&F 5 mm thick PVC sheet fillet of 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and as directed.

S&F solid PVC wall panelling consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifiecations and drawing complete all as specified and as directed.

M&L for vitrified tiles lightshade (square /rectangular) polished area of each tiles nexc 0.36 sqm in floors laid over and incl. 15 mm thk 1:4 screed bed jointed pointed with coloured cement to match the tiles. Size (600 x 600 mm) complete all as specified and as directed. Make :- Kajaria/Somany/ Johnson/Orient bell

All as per Item No. 170 above but in vertical surfaces such as skirting / dado laid over and incl. a backing coat of 10mm thk CM 1:3 complete all as specified and as directed. Make :- Kajaria/Somany/Johnson/Orient bell

M&L for non skid ceremic white tiles 7 to 8mm thk area of each tile exc 0.06 sqm but n exc 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to mortar.Laid over and including15 mm thick cement screed bed in CM 1:6 (Size 300 x300mm) complete all as specified and as directed. Make :- Kajaria/Somany/ Johnson/Orient bell

M&L for 10mm thick vitrified pavic tiles darkshade (square /rectangular) polished area of each tiles not exc 0.36 in floors laid over and incl. 20mm thk 1:6 screed bed jointed pointed with coloured cement to match the tiles. (Size 300 x300mm) complete all as specified and as directed. Make :-Somany/Johnson/Nitco

S&F Factory Made Solid PVC Moulded Door Shutter (with particle board core) , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and as directed.

S&F Factory (Solid PVC Moulded Door frame ) made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprisingof virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). → Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F powder coated(powder coating min 50 micron) anodised door shutters , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified and as directed.

Prelaminated particle board of 12 mm thk board ,interior grade ,prelaminated one side with decorative choice lamination & other side balancing , white lamination , fixed with screws to timber frame work complete all as specified and as directed.

M&L for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 using 40mm graded aggregates as in surface channel and drain, complete all as specified and as directed including demolition of old PCC as in surface channel and drain.

M&L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, miltred/stopped ends etc. complete all as specified and as directed.

S& F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde E- 250) quality A complete all as specified and as directed

M&L for two coats synthetic enamal paint over Surfaces of any description wood , steel, iron, concrete, brick, stone, etc. n exc 10cm in width or girth complete all as specified and as directed.

Excavation in post holes not exc. 0.5 cum, getting out returing, filling in and ramming earth and broken hard core/rubble mixed with earth with around the layers not exiding 25 cm each layers watering and removing surplus soil to a distance not exceeding 50 cm making good complete in soft/loose soil complete all as specified and as directed.

M & L PCC 1:4:8 type C2 (using 40 mm graded aggregate) as in Foundation filling and mass concrete complete all as specified and as directed.

S & F Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

MS work for screws bolts (Machine made) with hexagonal or square heads at one end and screwed both ends, each screwed end to be fitted with washers and square nut, exc. 5 cm and n. exc. 10 cm long diameter of shank 11 to 15 mm complete all as specified and as directed.

Supply only welded steel wire febric, any size or type complete all as specified and as directed.

Fixing only welded wire mesh febric including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed by Engr-In-Charge

E/M Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified and as directed.

Material and labour for point wiring with single core PVC insulated unsheathed cable of size 1.5 Sqmm nominal area with multi-stranded FRLSH copper conductor, 1100 Volt grade drawn through and including PVC non metallic surface casing capping of suitable size with all fitting and accessories including PVC modular board of suitable size for housing/mounting the modular switches/sockets, etc top covered with plastic laminated sheet 3mm thick including 1.5 Sqmm PVC insulated unsheathed single core FRLSH copper conductor earth continuity wire connected to common earth dolly complete for one light/fan point controlled by one way switch including making good disturbed surfaces complete all as specified and as directed.

All as per Item No. 190 above but for one 2/3 pin socket outlet, 5 Amps on same board, complete all as specified and as directed.

All as per Item No. 190 above but for one bell point controlled by 1 Bell push , complete all as specified and as directed.

All as per Item No. 190 above but with FRLSH, ISI marked PVC insulated and unsheathed two single core multistranded copper cable of size 2.5 sqmm for one power point ,3 pin 15 Amps on independent board includingFRLSH, ISI marked PVC insulated unsheathed single core multi-stranded copper cable of size 2.5 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed. Make- Cable- Finolex/RR cable/Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

All as per Item No. 190 above but with 2.5 Sqmm cable for socket outlet point 5 Amp on Independent board complete all as specified and as directed.

Supply and fixing modular switch 1 way 6 A module with cover plate and frame 230/250 volt , AC supply, ISI Marked, with cover plate complete all as specified and as directed.

Supply and fixing modular bell push 1 way 6 A module with cover plate and frame 230/250 volt , AC supply, ISI Marked, with cover plate complete all as specified and as directed.

Supply and fixing modular sockets 6A 2/3 pin combined 2 module with cover plate and frame 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and as directed.

Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module with cover plate and frame 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and as directed.

Supply and fixing modular switch 16A 1 module with cover plate and frame 230/250 Volts, 50 Hz , AC supply, ISI Marked, c with cover plate complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and as directed. Make : Cona , Plaza, Anchor .

Supply and fixing call bell ding dong, AC, 230 V, Single pole ISI marked complete all as specified and as directed. Make- Havells/anchor/ Legrand.

Supply and fixing LED batten fittings 1x 20 Watt complete including LED light driver, holder, LED lamp and connection up to ceiling rose with three core wire fixed to wall with 2 nos PVC block of suitable size including taking down old unserviceable one complete all as specified and as directed.

S & F Wall bracket decorative LED Spot light Light fitting with lamp 10 Watt Aluminium housing complete with necessary connection including taking down old unserviceable one complete all as specified and as directed.

S&F lamp holder, insulated body, with back plate for batten fitting complete all as specified and as directed. Make- Havells/anchor/Legrand.

Supply and fix in repairs LED lamp 7 Watt B22 base Color Temp 6500 K complete including taking down old unserviceable one complete all as specified and as directed. Make Phillips/Bajaj

S & F in replacement of LED / Bulk head Light fitting with lamp 1 x 9 watt including LED light driver, holder, LED lamp and connection up to ceiling rose with three core wire complete with necessary connection including taking down old unserviceable one complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete complete all as specified and as directed.

S & F Exhaust fan 230 volts , 250mm,plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall complete all as specified and as directed. Make Bajaj/Havell's/CG.

Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and as directed. Make: Havells Cat part No DHDPSHODRW12 or equivalent in Schnieder/GE/C&S.

Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and as directed including taking down old one. Make: Havells Cat part No - DHMCCDPF006-032 or equivalent in Schnieder/GE/C&S.

Supply and fix in repairs MCB, single pole 240 volts, 6 to 32 Amps, 10 kA 'C' curve capacity fixed in DB's complete all as specified and as directed. Make : Hager as per cat part- NCN106N, Schneider as per cat No : A9N4P32C or Indoasian as per cat No : 81195.

Material and labour for sub main wiring with two single core 4.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 4.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed, including taking down unservicable one.(Note: two run of 4.0 sqmm cable , one run of earth wire of 4.0 sqmm and one run of PVC casing capping shall be measured as one length) complete all as specified and as directed. Make- Cable- Finolex/RR cable/Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Taking down existing energy meter and refixing the same after completion on the original location complete all as specified and as directed. by Engr-in-Charge

Taking down existing water heater of any capacity and deposit the same at AGE E/M Store yard complete all as specified and as directed. by Engr-in-Charge

Supply and fixing of hot water Geysers of 25 ltrs capacity 5 star rated vertical type includng fixing of bolts , nuts grouted into the wall , and necessary cement work , making good of disturbed surface of wall , giving electric and water connection and testing after installation complete all as specified and as directed. Make : Havells cat part no - GHWCAMTWH025 : /LG/Ronald.

S&F heat resistant PVC connection pipe for hot and cold water 450mm long 15mm dia complete all as specified and as directed. Make: Prayag or equivalent in Polytuf/ Havells/ Sona.

Supply & laying galvanized steel tubing, medium grade laid in trenches/floor/wall and joined including necessary fittings such as bends, elbow, tees, sockets, etc for 15mm dia pipe complete all as specified and as directed.

Supply and Fix of Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and as directed.

M/S U.K ENTERPRISE