Addn Altn incl Special repair to building No P 6 P 7 P 8 P 17 AND P 18 JCOs MD Accn at BDTC area and P 23 Offrs MD Accn at Old Mandalay lines under GE MH AND RH Kirkee

Amount

Dismantling Floor, Hearth or Wall tileing including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises outside MD land complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] including removal of debris out side MD land complete all as specified and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and including removal of debris out side MD land complete all as specified and as directed.

M&L for block masonry with solid block of precast cement concrete class designation C-5 (using 20mm graded stone aggregate), exc 10cm in width and setting in cement mortar (1:6) complete all as specified and as directed.

M & L broken stone hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M & L for 75 mm thick, PCC (1:4:8), Type D-2, using 40mm graded stone aggregate as in Sub base for flooring including use of necessry formwork if required complete all as specified and as directed.

M & L for 75mm thick, PCC (1:3:6), Type C-1, using 20mm graded stone aggregate as in Plinth protection etc surface finished even and fairwithout using extra cement including necessary form work if required, provision of vertical joints at 2 mtr centre to centre and at corners by inserting 2-3mm thick PVC strip in full thickness all as directed by Engr -in- charge. Note: 1. The concrete for plinth protection should provide after taking down existing plaster from wall upto thickness of PCC and applying cement slurry over the rough surface for proper bonding alongwith wall 2. The rate for taking down plaster and providing slurry is deemed to be included in the rate and no xtra cost is admissible on this account.

M & L for 40 mm thick PCC (1:2:4), Type B-1 using 20mm graded stone aggregate as in flooring, surface finished even and smooth without using extra cement including use of necessry formwork if required complete all as specified and as directed.

M & L for coloured Chequered Cement Concrete Tiles 250 mm X 250 mm X 25 mm thick, set, jointed and pointed in neat cement slurry in floors / vertical surfaces / risers / bullnosed treads with gray cement including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar (1:6) complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc and including removal of debris out side MD land complete all as specified and as directed.

M & L for one piece machine cut Kota stone slab flooring using 20 to 25mm thick slabs, as in treads of stairs etc., laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:6 complete all as specified and as directed. The edges of treads shall be half moulded and three Nos longitudinal grooves are to be provided to make the stair non slippery, all as specified and directed.

M & L for one piece machine cut Kota stone slab as in riser of steps, skirting, dado etc using 20 to 25mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabs over backing coat of 10mm thick in cement mortar (1:3) including triangular filleting on top in cement mortar (1:4) complete all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Coloured, of size exceeding 0.06 Sqm and not exceeding 0.11 Sqm, 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar (1:4 ) complete all as specified and as directed. (Make: Somany/Kajaria/Orient Bell as approved by GE)

M & L for Non Skid Ceramic Tiles, Coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18Sq.m, 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. (Make: Somany/Kajaria/Orient Bell as approved by GE)

M & L for Glazed Ceramic Tiles, Coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7mm to 8 mm thick [Square or Rectangular] as in Vertical Surfaces such as Skirting, Dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat of 10mm thick in cement mortar 1:3 including triangular filleting on top in cement mortar (1:4) complete all as specified and as directed. (Make: Somany/Kajaria/Orient Bell as approved by GE)

M & L for Vitrified Tiles, Coloured, First Quality, (Double charged) of size 600 mm X 600 mm, 9 to 10 mm thick as in Floors, set and jointed in cement slurry, finished with flush pointing in white cement or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4, laid over and including 25mm thick PCC type B-0,1:2:4 (using 12.5mm graded aggregate) complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE. (Make: Somany/Kajaria/Orient Bell as approved by GE)

M & L for Vitrified Tiles, Coloured, First Quality, (Double charged) of size 600 mm X 600 mm, 9 to 10 mm thick as in Vertical Surfaces such as Skirting, Dado etc. set and jointed in neat cement slurry, finished with flush pointing in white cement or coloured cement to match over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for RCC (1:2:4), Type B-1, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for fair finished surfaces of concrete complete all as specified and as directed.

Use and waste of form work to edges of rough finished concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc. 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

S & F reinforcement using TMT steel bars of 8mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

M & L for rendering to external brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, surfaces finished even and fair without using extra cement including mixing of liquid water proofing compound of approved make @ 0.40 Ltr per 50Kg of cement complete all as specified and as directed. Note: Liquid water proofing compound will be measured and paid separately.

M & L for rendering to internal brick / concrete surfaces, 15 mm thick in Cement Mortar (1:6), surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying two or more coats of Cement based Wall Care Putty having average thickness of minimum 3mm of make JK / Birla / Jenson & Nicholson / Altec on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and as directed.

M & L for preparation of newly plastered wall surfaces and applying two coats of exterior weather proof emulsion paint over a coat of primer all as specified and directed by Engr -in- charge.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

M&L for Pressed steel frames made out of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed of size 105 x 60mm all as specified and as directed.

M&L for Pressed steel frames made out of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed of size 125 x 60mm all as specified and as directed.

M & L for PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate for filling in steel door frames complete all as specified and as directed.

S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

M&L for cutting holes in brick/stone walls in cement mortar for inserting holdfasts at door/ladders and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, depth of embedded portion of hold fast exc half bricks and not exc one brick complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for preparation of old painted wood and wood based surfaces of any description not other wise described not exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on walls with steel wire brushes etc., and applying two or more coats of Cement based Wall Care Putty having average minimum thickness of 3mm of make JK / Birla / Jenson & Nicholson / Altec on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over one coat of coat of alkali resistant primer on walls complete all as specified and as directed.

M&L for complete removal of existing finishes by scraping down old decorative surface of walls with steel wire brushes and removing smoke spots, moulds, efflorescent salts including filling of spots with POP , chalk whiting priming and applying three coats of white wash on old surfaces of walls all as specified and directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying two coats of white wash on ceilings complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying one coat of oil bound distemper on ceilings complete all as specified and as directed.

M & L for washing, rubbing down and stopping of painted surfaces and applying two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] on walls with approved colour and pattern over a coat of primer on old surfaces complete all as specified and as directed.

M & L for rendering 10 mm thick in Cement Mortar (1:3) on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

S&F 20mm bore GI tubes, medium grade, galvanised , with all fitting & fixed complete to walls & ceilings or laid in floors all as specified and as directed

Fixing only 20mm bore GI tubing of size 'medium grade' with and including S&F new all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /ceiling and including clips, wall hooks etc, complete all as specified and directed (Note: Old GI pipes as obtained from taking down shall be used under this item)

S & F 15 mm bore tubes, medium grade, galvanised, with all fitting & fixed complete to walls & ceiling or laid in floors, all as specified and as directed [The rate is deemed to be included for concealing of GI tubes wherever required and directed].

Fixing only 15mm bore GI tubing marked of size 'medium grade' with and including S&F new all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /ceiling and including clips, wall hooks etc, complete all as specified and directed (Note: Old GI pipes as obtained from taking down shall be used under this item, The rate is deemed to be included for concealing of GI tubes wherever required and directed].

S & F in repairs looking mirror with PVC frame and 5.50 mm thick glass of approved quality (size 0.60 x .45 m) complete all as specified and as directed.

S&F in repairs 15mm dia, Bib taps, fancy type, chromium plated with capstan or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and suitable for 15 bore of pipe fixed all as specified and directed ( Make : Jaquar Model- No CQT-23037 Bib Cock or equivalent model in Marc/ ESS-ESS as approved by GE. )

S&F in repairs of two way Bib cock 15mm dia , fancy type, chromium plated with capstan or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and suitable for 15 bore of pipe fixed all as specified and directed (Make : Jaquar Model No -CON-041KN 2 Way Bib Cock or equivalent model in Marc/ ESS-ESS as approved by GE.)

S & F in repairs Vitreous china ware wash hand basin, padestal pattern, white, flat back of size 560 mm X 420 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting stand, 32mm bore PVC flexible waste pipe and 15mm dia PVC connection 600mm long etc. complete all as specified and as directed. (Make-Hindware (ALTO) Cat No 10091 or equivalent model in Parry Ware (Super fine), Neyveli Ceramics (Neycer) (1st quality), Cera (1st quality) as approved by GE.)

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting stand, 32mm bore PVC flexible waste pipe and 15mm dia PVC connection 600mm long etc. complete all as specified and as directed. (Make-Hindware ( ALTO) Cat No 10091) or equivalent model in Parry Ware (Super fine), Neyveli Ceramics (Neycer) (1st quality), Cera (1st quality) as approved by GE. )

S&F in repairs stop valves suitable for 15mm bore iron pipe, fancy type, chromium plated with long shank and cup (concealed type) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed

S & F in repair PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed. (Make : CERA, Hindware or Equivalent as approved by GE)

S & F in repair ball valves suitable for 20 mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball, screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed.

S & F in repairs, Brass Chromium Plated Shower Rose of size 80 mm with or with out swivel joints with CP Arms including fixing to steel pipes complete all as specified and as directed.(Make: Jaquar cat pat No OHS -1995 & SHA 477 or equivalent in Marc and Ess-Ess as approved by GE)

S & F in repairs PVC connection of 450 mm length, suitable for 15 mm bore pipe with PTMT nuts, complete all as specified and directed.

S & F in repairs PVC connection of 600 mm length, suitable for 15 mm bore pipe with PTMT nuts, complete all as specified and directed.

S & F in repairs, Pillar Taps, cast copper alloy, Chromium Plated, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. (Make : Jaquar CAT Part No con -011KN or equivalent model in Marc/ ESS-ESS as approved by GE. )

S&F in repairs 15mm dia Central Hole Basin Mixer CP brass chromium plated with capstan heads without Popup Waste System with 450mm Long Braided Hoses fittings complete all as specified and directed ( Make : Jaquar Cat Part No CON-167KNB or equivalent model in Marc/ ESS-ESS as approved by GE. )

S & F in repairs Wash basins oval type, vitreous China, size 560x400mm including brackets incl fittings like 15mm dia PVC connection 600mm long and waste pipe of 32mm dia all as specified and directed. (Make-CERA Cat Part No S2030103 or equivalent model in Parry Ware (Super fine), Neyveli Ceramics (Neycer) (1st quality) as approved by GE. )

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar, complete all as specified and directed.

M&L 20mm Granite ('Z' black shade) work (table rubbed and polished) in steps, jambs, cills, for counter tops and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 20mm Screed bed in CM 1:4, all as specified and directed. Note : The rate quoted is deemed to be included for full moulding of edges wherever directed by Engr-in-Charge.

S & F Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [exclusive of steel sheeting or other covering, running rails and guides] and hanging, also fastening and fixing complete all as specified and as directed.

S&F in repairs PVC ( SWR) bends any radius bore of 75 mm all as specified and directed.

S&F in repairs PVC ( SWR) bends any radius bore of 110 mm all as specified and directed.

S&F in repairs PVC (SWR) pipes 75 mm dia single sockets, in any length rubber ring joints, fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm bore( as in RWP) etc dia single sockets, in any length rubber ring joints, fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) branch piece 75 mm bore, single Y equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) branch piece 110 mm bore, single Y equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) junction 75mm bore single T equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) junction 110mm bore single T equal or unequal all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.Make:Jaquar cat pat No AHS 1507 or equivalent in Marc or Ess-Ess as approved by GE. )

S&F in repairs of Towel Ring Square with Round Flange complete all as specified and directed. (Make - Jaquar Cat Part NO. ACN-1121N or equivalent model in Marc/ ESS-ESS as approved by GE. )

S&F in repairs Health faucet chromium plated (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook fixing to 15 mm bore of pipe all as specified and directed. (Make - Jaquar Model No - ALD-CHR-593N or equivalent model in Marc/ ESS-ESS as approved by GE. )

S&F in repairs 15mm Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.Make: Jaquar cat part No CQT 23167B or equivalent in Marc or Ess-Ess

S&F in repair CP grating ring or frame square or round 150mm size complete all as specified and directed.

S&F PVC waste pipe 32mm dia non transperant suitable for sink/WHB complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and directed. Make: Cera cat part No F 5001114 or equivalent as approved by GE. )

S&F in repair toilet paper holder brass chromium plated fixed to wall with brass screw complete all as specified and directed. (Make :- Cat No AHS-1551 Make JAQUAR or equivalent model in Marc/ ESS-ESS as approved by GE. )

S & F in repairs Vitreous china wash down water closet [Pedestal pattern], white [excluding flushing cistern and flush pipe] including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

S & F in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mmX440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc, including trap set in and including concrete complete including making good to floor all as specified and directed.

Taking down shutters of any description n.exc 1 Sqm each complete all as specified and directed.

M&L for Clean sawn 2nd class Hardwood as in Scantlings complete all as specified and directed.

M&L for fillets, bullnosed, splayed, chamfered or rounded on edge or face of sectional area exc. 3 & n.exc. 6 Sqcm in Ist class hard wood complete all as specified and directed.

S&F in repairs cup board knobs 50mm size , polished hardwood ,decorative fancy type with all fixing screws etc. complete all as specified and directed.

S&F in repairs 150mm , Brass almirah handle, polished bright, including magnet catchers etc. arrangement to built in cupboards complete all as specified and directed.

S&F in repairs, Brass drawer handles projecting flush drop (65 to 75mm grip) on 4 screws plate including letting in all as specified and directed.

M&L in repairs 12 mm thick Prelaminated particle board , interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timer frame work as in cupboard, wardrobes or shelves partitions etc. complete all as specified and directed.

S&F in repair continuous (Piano) hinges, width of flaps (when open ) 30mm , mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F in repair Hasp and staple 75mm , safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repairs MS Sheets 1.25mm thick as in shutters of cupboard , shelves (partition of built in steel cupboard) , cut to size including benching or turning up complete all as specified and directed

S&F in repairs mild steel mortice lock, vertical type , size 100mm ,4 levers as in wardrobes, almirah etc. complete all as specified and directed.

M&L for spot welding for repairing steel windows and ventilators hinges, brackets , steel handles etc. complete all as specified and directed.

S&F in repairs powder coated aluminium pipe 25mm dia and 2mm thick as in curtain rod fixed to brackets complete all as specified and directed. (shade and design as approved by GE) (Note : Brackets shall be measured and paid separately )

S&F in repairs powder coated aluminium brackets fancy type for curtain rods complete all as specified and directed.(shade and design as approved by GE)

S&F in repair stainless steel cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed.

S&F stainless steel cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed.

S&F Cast iron soil waste and vent pipes, 100 mm bore, in any length with or without ears with cement joints, laid in trenches or in floors complete all as specified and as directed.

S&F Cast iron floor trap 100 mm bore with CP grating and ring/frame including jointing to waste pipe and fixed with PCC 1:2:4 complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel sheet 1mm thick for kitchen or laboratory with plugs, washers and waste, including cantilever brackets, CP waste coupling and PVC waste pipe overall size of sink 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F plate rack made of stainless steel sheet 1mm thick and overall size 915mm x915mm x 255mm complete all as specified and as directed. (Make: Nirali/Prayag/Blue star as approved by GE)

S&F bathroom cabinet mirror (of approved pattern) of size 450mmx 350mm regular size with mirror and PVC shelves complete all as specified and as directed.

S&F in repairs bathroom cabinet mirror (of approved pattern) of size 450mmx 350mm regular size with mirror and PVC shelves complete all as specified and directed by Engineer-in-Charge.

S & F Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 500 Liters Capacity double layered 'ISI' marked, hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete including taking down old tanks and removing to store or given to contractor as credit complete all as specified and as directed.

S & F Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 1000 Liters Capacity double layered 'ISI' marked, hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete including taking down old tanks and removing to store or given to contractor as credit complete all as specified and as directed.

S&F box type windows and ventilator, fabricated from roll formed sections made of Galvanized steel powder coated/colour coated (Base Steel as per IS 513 'D' quality, Galvanized as per IS 277 with Zinc of 120 grams/Sqm) with total coated thickness of 0.60mm (Note: (i) Coated Sections should be with Primer Coat of Epoxy Primer of 5-7 microns thick, finish paint with Polyester paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, with total coated thickness of 0.06mm (ii) Sections for Frame should be of 72mm x 55mm, section for Mullion should be of 72mm x 50mm, section for Shutter Frame should be of 47mm x 20mm, Section for Fixed Glass Bead should be of 12mm x 12mm and section for Fly mesh should be of 40mm x 20m (iii) Section for Frame Glazed Shutters and Mesh Shutters Should be cut to length and joined with Polypropylene Corner Brackets, Mullion Section should be joined wth Frame/Mullion using Mullion Cap Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter and Fixed Glass. (iv) Each Glazed shutter should be provided with SS Pivot Hinges-1 set, secolor make handle with receiver -1 No and Friction stay Powder Coated-1 No. For Each mesh shutter should be provided with Pivot Hinges-1 se, Seccolor make Handle. (v)Glazesd shutter and Fixed Glass portions should be provided with a glass of 4mm plain Glass. (vi) Mesh shutter should be provided with a stainless steel 32 guage Fly mesh of 304 grade with 144 holes per Sq Inch. (vii)Window and ventilators should be provided with grill made of 10mm Sq. MS Bars welded to at 150mm centre tocentre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fix with the window frame with self tapping screws. (viii) Window and ventilators should be fixed to brick/concrete masonary by using Nylon self - expending caps and driving MS electroplated 80mm long screws into the caps through frames. (ix)Ref TD drg No CEPZ/2016/TD/03 sheet, 1/3 to 3/3 for details.

Taking down old steel windows of any description and size and S&F aluminium powder coated window sliding type (3 track) with frame size 100x35x1.20mm and shutter 39.40x17.70x1.20mm with two glass shutter and one stainless steel wire mesh shutter including necessary jointing cleats, glazing clips, rubber packing powder coated aluminium snap beading screws with 4mm plain float glass and 0.56mm dia SS wire mesh, fittings etc, and necessary locking arrangements and including making good the jambs and painting with matching type and shade complete all as specified and directed (Make of Aluminium section: Jindal/Hindalco as approved by GE. )

Taking down old steel ventilator of any description and S&F powder coated aluminium frame for ventilators and in partitions , with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

Demolition of cement concrete (un-reinforced ) of any description and in any position not otherwise specifically provided for including removal of debris out side MD land complete all as specified and as directed.

M & L for PCC (1:5:10) using 40mm graded burnt bricks aggregate as in foundation filling & mass concrete or as in sunken floors complete all as specified and as directed.

M&L for water proofing treatment to RCC sunken slab (n.exc. 45 cm depth of sunken) complete all as specified and as directed consisting of following steps:- (a) M & L for rendering to brick / concrete surfaces of sunken slab floor and vertical sides, 15 mm thick in Cement Mortar 1:3, surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make @ 0.40 Ltr per 50Kg of cement complete all as specified and as directed. (Note: Liquid water proofing compound will be measured and paid separately.) (b) Providing and fixing of 40-50mm dia GI pipe medium grade / spout pipe by cutting through walls complete (c) Creating fillet coving of 50x50 mm with polymer modified mortar (d) Applying first coat of two component modified polymer coating on horizontal and verticle surfaces. (e) Provn of glass fiber mesh 2x2 mm immediately on above polymer coating (f) Apply second coat of two component modified polymer coating after 72 hrs . ( plastered , PCC paid sep.) plan area shall be measured

Supply only liquid water proofing compound [ISI marked] of approved make.

Supply and fixing 18mm thick white marble corner shelves of 30 cm radius fixed in bath and WC complete all as specified and as directed.

Supply and fix glass dividing strip 3mm thick and 38mm wide, inserted in postion, conforming to design complete all as specified and as directed.

M&L for writing of letters or figures (Block, Roman, Italic or Indian)n.exc. 30cm height complete all as specified and as directed.

Supply and fix 35mm thick 2nd class Hard Wood glazed and skeleton shutters, open rebated and prepared to receive glass and gauge etc. complete all as specified and as directed.

Excavation in post holes (or similar holes) in hard/dense each n exc 0.5cum, getting out, removing surplus soil to a distance n exc 50m and making good surface complete all as specified and as directed.

S&F 32mm bore GI tubes, medium grade, galvanised , with all fitting & fixed as in over flow pipes.complete all as specified and as directed

S & F stainless steel butt hinges 100mm size screwed to PVC doors all as specified & directed

M & L cement concrete type B2 (1:2:4, 40mm graded aggregate) as foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under -reamed piles and mess concrete

S&F Powder coated Aluminium grill of approved pattern using channel of required size, screwed to windows & ventilators with self tapping screws all as specified & directed Note :- Design and pattern as approved by GE.

S & F for framed work such as barred iron door; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 including taking down existing rungs from wall and making good the surface all as directed.

1)M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.) 2)M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed.

M&L for Providing and fixing additional steel bar in various structural elements like column ,beams and Slab etc. including drilling ,bending and fixing the bars tying with preleft binding wires etc.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application, complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar thickness upto 40mm thickness including leveling profiling etc. complete. Each layer should not have a thickness more than 20 mm with epoxy latex based bond coat before each layer

Cutting of tree branches of girth n.exc 30cm dangerously/precariously hanging above bldgs completely all as specified and directed by Engr-in-charge (upto 3 storied bldgs) Note ; All the precautionery work for the safety of workers are the responsibity of the contractor only.

M & L for removal of plant growth of any descreption & height upto three storied bldgs along soil/Vent/rain water pipe or along wall/roof by injection with chemical glyphospate solution (4% concentration) of 20ml or till refuse by cutting or injecting in stem of plants or roots at 30mm in depth. The area shall then be sprayed with solution 25ml glyphosphate (4% concentration) complete including scaftolding all as specified.

Taking down existing roof treatement of any description including cement plaster below the treatment and removing the debris to a distance exceeding 50 mtr.complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on concrete surface (roof) mixed with water proofing liquid (being paid seperately) finsined even and fair.

M& L cleaning the plasted /concrete surface with wire brush and applying water proofing treatement as under (a) Apply a uniform coat of bitumen primer @ 0.70 Kg/Sqm over cement plaster (b) Providing and applying 3mm thick and weighing not less than 3.6 kg /sqm (APP) modified bitumen based pre fabricated five layer water proofing membrane reinforced with non woven polyster matt black finished by torch application of membrane with 10 cm over lape both ways after necessary prepration of surface complete as menufacture instrutions. (c) Apply two coats of bitumatic aluminium paint over membrance.

Taking down carefully copper/aluminium point wiring (light, Fan, socket,Geyser or power) complete (fittings such as switches, ceiling roses, pendants, regulators, light fitting etc, removing materials to store for keeping in safe custody for credit (credit for above items should be made as per conditon of material separately) and making good distrubed surfaces of wall/floor/ceiling etc complete all as directed

M & L for point wiring complete with and including 1.5 sqmm (nominal area) single core multi stranded copper conductor PVC insulated but unsheated FRLS cable 1100 Volts drawn in to and including PVC rigid non metallic concealed conduit ISI marked of suitable size including its accessories such as tee, bend ,elbow, socket and chisselling on wall complete and also making good the disturbed surfaces of wall / ceiling by cement mortar 1:4 including painting to existing surfaces and also including 1.5 sqmm PVC insulated and PVC unsheathed single core multistranded copper conductor FRLS cable 1100 V grade as earth wire on Modular metal flush box of suitable size and thickness 1.22 mm as per circuit requirement (modular plates measured and paid separately) for housing switch ,socket,regulators etc complete for the following:-

(a) One light point controlled by one one way switch

(b)One ceiling /Exhaust Fan point controlled by one one way switch

(c ) One 3 pin 5 Amps socket outlet on independent board.

(d) Bell /buzzer point controlled by one bell push. Note: (i) For each offr qtr & JCOs qtr 1/Each. (ii) Each servant Qtr-01 no, (iii) From Offr qtr to servant qtr-01 No/Each)

(e) One 3 pin socket outlet 5 amps on the same board with other switches, with cables 1.5 sqmm size

(f) one light point controlled by two no of two way switch two way point

All as per item No 146 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 V grade PVC insulated but unsheathed single core for 16 Amps power point on independent board and 2.5 sqmm cable as earthwire. complete all as specified and directed.

S & F Modular switch 2 way 6 Amp, 1 module complete all as specified and directed.

S & F Buzzer, Ding dong, AC 230 volts, single pole complete all as specified and directed.

S & F switch Modular 230 volts, single pole, one way 5 Amps , 1 module complete all as specified and directed.

S & F Modular switch socket combination , 3 pin , 5 Amps flush type complete all as specified and directed.

S & F Modular switch socket combination, 16 A, 6 pin, 3 module complete all as specified and directed.

S & F Modular socket 6 A-2/3 pin combined 2 module complete all as specified and directed.

S & F Modular Bell push, flush type, 6 amp . 240 v, 50 Hz complete all as specified and directed.

S & F PVC ceiling rose surface type three terminals type including square metal or plastic box complete all as specified and directed.

S & F Triple pole and earth enclosure with a three pin and earth plug with socket complete with one triple pole 32 amps MCB complete all as specified and directed.

S & F Modular white cover plate with frame 1 module, complete all as specified and directed.

S & F Modular white cover plate with frame 2 module, complete all as specified and directed.

S & F Modular whtie cover plate with frame 3 module, complete all as specified and directed.

S & F Modular white cover plate with frame 4 module, complete all as specified and directed.

S & F Modular white cover plate with frame 6 module, complete all as specified and directed.

S & F Modular white cover plate with frame 8 module, complete all as specified and directed.

Taking down ceiling fan, celing cable end, dismantling blades and removing fan and blades and depositing at AGE E/M (West) Kirkee store.complete all as specified and directed.

M & L for Fan hook , clamps holdfasts with all necessary materials for hanging fan complete all as specified and directed.

Supply & fix energy efficient ceiling fan with BLDC motor and blades, 1200 mm sweep, with operating voltage of 140 to 285 V, with metallic finish , with and including step type modular regulator 120 W / remote toggle switches complete all as specified and directed. Make: Crompton or equivalent make of Havells/Usha as approved by GE .

Supply and fix heavvy duty exhaust fan AC Single phase 230/240 volt, of size 300 mm sweep, 900 RPM with louvers including necessary cutting of wall and plastering etc. Make: Havells or equivalent make of Crompton/Almonard as approved by GE .

Supply and fix exhaust fan AC Single phase 230/240 volt, of size 380 mm sweep , 900 RPM, with louvers including necessary cutting of wall and plastering etc. Make: Havells or equivalent make of Crompton/Almonard as approved by GE .

Supply and fix wall fans 230 volts, single phase, oscillating 450 mm sweep suitable for wall mounting. (For officers qtr Kitchen). Make: Havells or equivalent make of Crompton/Almonard as approved by GE .

Taking out old converntional type building security light fittings complete including bracket of any capacity or of any description. and Supply and fix LED street light 36 W IP-66 with cast aluminium hbousing, toughened glass diffuser and wiried with accessories for building security including bracket, clamps, washers, bolts, drilling of wall making surface good and accessories . Make: Shakti cat No: SZPSLMM036 or equivalent make of Crompton/Philips/Wirpro as approved by GE .

Taking down old unserviceable conventional FTL fitting ,Supply & fix LED batten suitable for 24 W LED batten with 24 W LED Tube rod 240 V, 50 Hz. Make: HPL cat No: HPLLEDPET524CWC or equivalent make of Crompton/ Philips/Wirpo/Shakti as approved by GE .

Taking down old unserviceable conventional FTL fitting ,Supply & fix LED batten suitable for 20 W LED batten with 20 W LED Tube rod 240 V, 50 Hz. Make:Shakti cat No: SZSRFMX1-20(Batten) & SZFRTMX020(Retrofit tube) or equivalent make of Crompton/ Philips/Wirpo/Shakti as approved by GE .

Taking down old unserviceable conventional FTL fitting ,Supply & fix LED batten suitable for 18 W LED batten with 18 W LED Tube rod 240 V, 50 Hz. Make: Shakti cat No: SZFRTMX018 & SZSRFMX1-18 or equivalent make of Crompton/ Philips/Wirpo/HPL as approved by GE .

M&L for sub main wiring but using two single core multistranded PVC insulated copper conductor of size 6 sqmm 1100 volt grade drown into including PVC Rigid conduit of suitable 20/25 mm dia, ISI marked including 6.0 Sqmm. PVC multi standard cable in green colour for continieous earthing including taking down old submian wiring and making good the disturbed surfaces of wall /floor/ ceiling to match with existing surfaces.all as specified and directed.(Main DB to Each SDB for each Qtr) Note : Two runs of 6 Sqmm PVC cable and one run of 6.0 Sqmm cable and PVC Rigid conduit shall be measured as one length.

M & L for sub main wiring but using two single core multistranded PVC insulated copper conductor of size 10 Sqmm 1100 volt grade drawn into and including PVC rigid conduit of 20/25 mm dia, ISI marked including 10.0 sqmm, PVC multi stranded cable in green colour for continuous earthing including taking down old submain wiring and making good the disturbed surfaces of wal/floor/ceiling to match with exisitng surfaces all as specified and directed. (main DB to Each SDB of officers qtr)Note : Two runs of 10 Sqmm PVC cable and one run of 10.0 Sqmm cable and PVC Rigid conduit shall be measured as one length.

Supply and fix water heater storage type, electric operated, capacity 25 Ltrs, BEE 5 star rated, 2 KW heating element including hot and cold water pipe, NRV, and accessoires including necessary GI pipe of 15 mm dia size from service tank to Geyser for JCOs Block. Make: Havells Cat No: GHWCARTWH025 or equivalent make of Racold/Philips as approved by GE .

Taking down serviceable Geysers of various capacity kept in store doing repairs, carrying out paintings and refixing , testing geyser on exisitng position including inlets, outlet water connection, on all as directed and satisfied by Engr-in-Charge.

M&L for sub main wiring but using two single core multistranded PVC insulated copper conductor of size 4 sqmm 1100 volt grade drown into and including PVC Rigid conduit of suitable 20/25 mm dia, ISI marked including 4.0 Sqmm. PVC multi standard cable in green colour for continieous earthing including taking down old submian wiring and making good the disturbed surfaces of wall /floor/ ceiling to match with existing surfaces.all as specified and directed.(Sub main for Geyser from SDB to Geyser point) Note : Two runs of 4 Sqmm PVC cable and one run of 4.0 Sqmm cable and PVC Rigid conduit shall be measured as one length.

M & L for disconnecting all electrical connection and taking down old corroded steel meter box from existing site, new self supporting wall mounted totally enclosed compartmentalised double door front openabe powder coated dust and vermin proof panel board of size 1.05 x .95 x .30 mtr made out of 2 mm thickness CRCA sheet suitable for fixing 5 Nos kwh meter and built upon rigid frame work having front doors with neoprence rubber gasket, earthing strip point at side, bottom detachable gland plate consisting of sufficient nos of circular cable entry holes at bottom only with suitable PVC insulated cables of adequate size including connectinos complete with suitabl size bolts and washers etc. Fixing of KWH meter, necessary connection to meters and MCB DB's and testing of meter, making the disturbed surface good as directed and satisfied by Engr-in-Charge. (Note: S & F meter measured separately)

Taking down old conventional KWH meter deposit to MES Store yard Supply & fix AC single phase static energy meter of accuracy class 1.0, 240 V, 50 Hz with Backlit LCD display of rating 5 - 30 A, (measures and displays KWH ,V, Current I, KW, pf last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power all as specified and directed by Engr-in-Charge. Make : L & T Cat No:QWM101BC5DDH or equivalent make of Havells as approved by GE.

Taking down old conventional kwh meter deposit to MES store yard Supply & fix AC single phase static energy meter of accuracy class 1.0 240 V, 50 hz with Backlit LCD display of rating 60 Amps, (measures anddisplays kwh, V, current I, KW, PF last month history of kwh, MD in KW) with special features like TOD, Tamper logging, optical communication port display in absence of power all as specified and directed by Engr-in-Charge. Make : L & T Cat No: WM101BC7DDH or equivalent make of Havells as approved by GE.

Taking down defective vertical TPN DB S & F Vertical TPN DB IP-43 metal door 4 way powder coated provided with insulated vertical phase bus bars, neutral barss with shroud earth bar sticking saddles, color coded interconnecting wire set cable ties blanking plates and circuit identification labels with provision for MCCB 4 pole as incomer and SP/TP MCBs as outgoings (MCCB measured separately) including making good the disturbed surfaces. Make: L & T cat No: DBVTL004DD or equivalent make of Hager as approved by GE.

S & F MCCB 4 pole, 415 Volt, 16 KA Breaking capacity, 125 Amps capacity all as specified and directed. Make: L & T/Hager/ABB as approved by GE.

Taking down defective distribution Board including MCBs and wooden boards all as directed and S & F distribution board factory made SPN 12 way in, 415 Volt, Double door metal type suitable for fixing MCBs including making good the surfaces to match with the existing all as specified & directed. Make: L & T/Hager/ABB as approved by GE.

Taking down defective distributin board including MCBs and wooden boards all as directed and S & F distribution board factory made SPN 2 way, 240 volts, single door metal type suitable for fixing MCBs including making good the surfaces all as specified and directed.

S & F MCB SP 2 to 25 Amps withstanding for 240 V, 50 Hz, 'C' series 10 KA with two position DIN Rail clamp. Make: L & T/Hager/ABB as approved by GE.

S & F MCB SP 50 amps withstanding for 240 V, 50 Hz, 'C' series 10 KA with two position DIN Rail clamp. Make: L & T/Hager/ABB as approved by GE.

S & F MCB SPN 50 Amps wtihstanding for 240 V, 50 HZ, 'C' series 10 KA with two position DIN Rail clamp. Make: L & T/Hager/ABB as approved by GE.

S & F MCB SPN 32 Amps wtihstanding for 240 V, 50 HZ, 'C' series 10 KA with two position DIN Rail clamp. Make: L & T/Hager/ABB as approved by GE.

M & L for Rigid non-metallic PVC Conduit 20 mm including junction boxesof all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc for telephone, cable point and GI wire drawn inside conduit all as specified and as directed.

S & F, connect T.V. Outlet mini Make: HPL cat No: SSTFTVOM or equivalent make of Havells/Anchor/Vinay as approved by GE.

S & F , connect Telephone Jack mini Make: HPL Cat No: SSTFT JM or equivalent make of Havells/Anchor/Vinay as approved by GE.

M & L for laying PVC Unsheathed single core copper cable 2.5 Sqmm size through PVC conduit pipe for inverter connection, controlled by one no of 2 way MCB DB with one No of MCB SP 25 Amps. Note: MCB DB & MCBs measured and paid separately.

Disconnecting and tking down in the unserviceable earthing and M &L for earting with galvanished steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground (earth pit not less than 3.25 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level connected to 4.0 mm dia galvanished earth lead wire by means of nuts bolts check nuts and GI washers including PCC pit in PCC 1:2:4 type B-1 RCC cover, 20 mm dia (MG) GI watering pipe with funnel wire mesh and protectin pipe of GI of suitable size upto 7.5 mtr length including charcoal black cotton soil as required at site to achieve the earthing result and common salt, excavation earth work etc in any type of starta complete all as shown in electrical plate No 5 as specified, GI wire suitable size and length for continuity earth wire from test point to main distribution board and all as directed. Note: Rate for achieving required depth by compressor machine if required is deemed included in tem unit rate.

UNICON

Mukund Engineers and Contractors

L.K.R.TIWARI CONSTRUCTION

vishalconstruction

Khanuja Industries

VIRENDRA FABRICATORS