Loading…
Loading…
Tender Value
₹97.3 L
EMD Value
₹1.9 L
Closing Date
24 Jun 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
CIVIL
14 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. (Refer details in tender document).
Definition of Similar Nature of Work:- ("Any Civil work other than EOT Track, Horticulture, Sanitation & P.Way work")
16 conditions · 3 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer(s) should deposit payment of EPF/ESI with the authority concerned for the preceding month of the wages month irrespective of number of workers and upload on the IR Shramik Kalyan Portal.
To assist in the examination, evaluation & comparison and prequalification of the Tender, the Railway may, at its discretion, ask any Bidder for a clarification of its Bid. Any clarification submitted by a Bidder that is not in response to a request by the Railway shall not be entertained or considered. The Railway request for clarification and the response of the bidder in this regard shall be in writing. However, if a Bidder does not provide clarification of its bid by the date and time communicated in the Railway request for clarification, the bid shall be evaluated as per the documents submitted along with the bid.
Tenderer should comply with the provision of EPF&ESI Scheme as modified from time to time and should registered themselves with concerned authority or submit registration issued by authority concerned within 30 days from the date of issue of (LOA), otherwise no payment will be released.
Quoted Rates shall be inclusive of all statutory taxes like GST, building cess, any allowance, license fee, royalty charges etc. as legally leviable by State, Central Government and/or any other local body/authority.
Replacement to damaged Grill & Ventilator shutters of bath & toilet in Type-II (503 Nos.), III(260 Nos.) & IV qtrs in colony-II PLW Patiala
T-04-2026-27
T-04-2026-27
Open
Works - General
8 Months
Patiala, Punjab
₹0
₹1.9 L
24 Jun 2026
2 Jun 2026
10 Jun 2026
24 items across 1 schedule · ₹93,56,077.1 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 10 | 9,793.75 | 97,937.5 |
| 2 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 4 | 10,185.05 | 40,740.2 |
| 3 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 100 | 766.55 | 76,655 |
| 4 | Mild steel and Medium Tensile steel bars | Kg | 700 | 88.95 | 62,265 |
| 5 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 20 | 8,512.1 | 1,70,242 |
| 6 | 75x47x1.70 mm | Each | 3950 | 32.75 | 1,29,362.5 |
| 7 | 100x10 mm | Each | 3900 | 58.65 | 2,28,735 |
| 8 | 100 mm | Each | 2000 | 53.25 | 1,06,500 |
| 9 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 8000 | 111.95 | 8,95,600 |
| 10 | Galvanised M.S. Wire gauge with 0.63 mm dia wire and 1.4 mm aperture on both sides | Sqm | 750 | 732.2 | 5,49,150 |
| 11 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 850 | 671.55 | 5,70,817.5 |
| 12 | 1:4 (1 cement: 4 fine sand) | Sqm | 4800 | 294.85 | 14,15,280 |
| 13 | Two or more coats on new work | Sqm | 300 | 131.45 | 39,435 |
| 14 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | cum | 2 | 2,007.1 | 4,014.2 |
| 15 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 2 | 2,928.1 | 5,856.2 |
| 16 | In cement mortar | cum | 10 | 1,698.45 | 16,984.5 |
| 17 | Of area 3 sq. metres and below | Each | 1750 | 302.7 | 5,29,725 |
| 18 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | Sqm | 4800 | 45.05 | 2,16,240 |
| 19 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 100 | 219.35 | 21,935 |
| 20 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 4000 | 466.3 | 18,65,200 |
| 21 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 2500 | 564.8 | 14,12,000 |
| 22 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 700 | 1,019.8 | 7,13,860 |
| 23 | Powder coated minimum thickness 50 micron aluminium | Each | 2000 | 79.75 | 1,59,500 |
| 24 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). | Kg | 50 | 560.85 | 28,042.5 |
| Schedule total | ₹93,56,077.1 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Tdocs.pdf
ATTACHMENT
SpecialData.pdf
ATTACHMENT
ACS-1to11merged_merged_compressed-compressed1.pdf
ATTACHMENT
CECIRCULAR630merged.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .