PROVN OF SPECIAL REPAIR TO BLDG NO P 54 OR MD ACCN AT GR LINE AND ADDN ALTN TO BLDG NO P58 AT BHAGAT COLONY AT MIL STN BIKANER

Amount

Dismantling existing terrazo dado /flooring or tilles in bath .WC and kitchen etc.

Demolition of lime concrete of any description over roof slab complete all as specified and as directed by Engineer-in-Charge..

Dismantling of brick work built in cement mortar including all quions arches pillars etc

Dismantling of stone patti as in roof slab provided below roof sab of any desc and thickness

Demolition of cement conc. In ground floor and paving not exc. 15cm thickness (below or above GL)

Demolition of cement conc. Reinforced as in roof slab , beams, chhajas and similar suspended work reinforcement cut as required to facilitate demolition.

Taking down cement plaster on brick or stone walls incl. all finishes tiles etc. raking out joints hacking for key scrubbing down with water etc.

Taking down chowkhats or frames not exc. 1.50sqm each but with shutter (w/o taking of shutter from the frame )

Taking down sheetters of any description but n exc 1.5 sqm and refixed in same opeing after easening and adjusting.

Taking down sheutters of any description but exc 2 sqm and refixed in same opening after easening and adjusting

Taking down shutters of any descripting but exc, 2 Sqm complete

Taking down chowkhats or frames exc. 1.50sqm each but n exc 4 sqm with shutter (w/o taking of shutter from the frame )

Taking down old rusted and damaged steel window/vent incl. guard bar and grill where exist of size not exc. 1.5 sqm each and all as specified and as directed by Engineer-In-Charge.

Taking down or up, 15 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engineer -in-charge.

Taking down or up, 20 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engineer -in-charge.

Dimantling water tanks cap exc 250 & n.exc.500ltrs.

M&L Form work to soffits of suspended slab such as roof slab not exc 200mm thick to rough finished surface of concrete

M&L Form work to edges of conc. Flat floor and roofs n.exc 20cm wide to rough finished surface of concrete .

M&L Form work to sides and soffitts of floor or roof beam, beam haunching, girders, bressume-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. complete all as specified and as directed by engineer-in-charge.

M&L Mild steel bars TMT 10 mm dia and over cut to length bent to shape required incl. cranking bending spirally for hoop for columns ,hooking ends and binding with and including mild steel wire not less than 0.9mm dia deformed or twisted bars.

M&L Mild steel bars TMT 8 to 10 mm dia cut to length bent to shape required incl. cranking bending spirally for hoop for columns ,hooking ends and binding with and including mild steel wire not less than 0.9mm dia deformed or twisted bars.

M&L for mild steel TMT bars 5mm dia and over upto incl 10mm cut to length bent to shape as reqd ,as in stirrups and spacers.

Reinforcement cement concrete design mix M-25 slab supported on wails beams and columns in floor roof landing and the like using 20mm graded stone agg.

M&L Lime concrete terracing as specified on roof

M&L for 10 mm thick plaster (screed bed) over roof slab in CM 1:4, Mixed with integral liquid water profing compound as per manufracturers instructions, finished even & smooth without using extra cement complete all as specified and as directed by Engineer-In-Charge.NOTE:- ( WPC to be measured separately as supply only)

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3 mm tick reinforced with polyster non wave fabric ( wt. not less than 150gms/sqm) land on primed surface by forced applicatio complete all as specified .

Supply only water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

M&L Applying evenly a tack coat of industrial bitumen 85/25 ,1.2kg/sqm incl cleaning surface.

M&L 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M&l for brick work with fly ash bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6.

M&L for brick work with fly ash bricks straight or curved on plan exc 6m mean radius as in half brick walls built in CM 1:4.

M&L Rendering 5mm thick on fair faces of conc. Surfaces in cement mortar 1:3,even and smooth w/o using extra cement as on ceiling.

M&L for Rendering 15mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:6,even and smooth w/o using extra cement .

M&L for Rendering 10mm thick cement plaster on fair faces of brick including water proofing compound or conc. Surfaces in cement mortar 1:4,even and smooth w/o using extra cement .(WPC to be measured separately as supply only)

M&L for rendering 10 mm thick plaster in CM 1:6 on other than fair faces of Brick work or on one side of lathing finished even and fair complete all as specified and as directed by Engineer -in-charge.

M&L for non skid ceramic tiles (coloured) 7 mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces such as dado, skirting etc, set and jointedin neat cement slurry and pointed in white or coloured cement to match the shede of tiles over and incl 10 mm thick rendering (as screed bed) in cemnent sand mortar 1:4 complete all as specified and as directed

M&L non skid ceramic tiles coloured 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm screed bed in CM 1:6 complete all as specified and as directed by engineer-in-charge.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (ie 450mm x 300mm or as directed), on vertical surfaces such as dedo, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and incl 10 mm thick rendering (as screed bed) in cement sand mortar 1:4 complete all as specified and as directed

M and L for coloured Non skid ceramic tiles7 to 8 mm thick (st noquare/rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over 15mm thick screed bed in cement mortar 1:6.

All as per item above but on vertical surface over 10 mm thick rendering in CM (1:4) complete all as specified and directed

S&F factory fabricated pressed steel frame/box windows, ventilators with glazed and fly proof shutters provided to size and dimensions as specified & shown on drawing No.BTD-888R Sheet No. 1/5 to 5/5 & BTD-889 Sheet No. 1/4 to 4/4 with & including shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified. Notes:- Notes:- (i) PCC for filling in frames , glass , wire guageand painting shall be measured & paid for seprately under respective items. Provision of all other items as shown & specified on drawing shall deemed to be included in quoted rate of this item. (ii) The quoted rate shall deemed to include provision of cutting holes of suitable depth in walls for inserting lugs etc and making good dismanteled portion in PCC 1:2:4 type Bo using 12.5 mm graded crushed stone aggregate and CM (1:3) and provision for cooler aplliance where ever required as per directions of Engineer-in-charge.

M and L for sheet glass 4 mm thick ordinary quality and glazing with oil putty in square not exc.0.5sqm in each pane

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed by engineer-in-charge.

M&L PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling in pressed steel frames complete all as specified and as directed by Engineer-in-Charge

M & L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded aggregates as in Plinth Protection of as in sub floors, sub base etc even and rough to receive the toppiong layer complete all as specified and as directed by Engineer-in-Charge.

M&L for plain cement concrete 25 mm thick 1:2:4 tye B0 (12.50 mm graded aggregate) as in leveling course over stone slab complete all as specified and as directed by Engineer-in-Charge.

M&L for Racking out joints / pointing to brick tiles 30 cm by 15 cm laid flat as in floors, roofs, ceiling, chajjasa etc and keyed pointing the same with CM 1:3 complete all as specified and as directed by engineer-in-charge

S&F 1.25 mm thick Pressed steel frames of size 125mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

S&F 1.25 mm thick Pressed steel frames of size 105mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

M&L for 2nd class hard wood 35mm glazed and skelton shutter open rebated and prepared to receive glass,gauge etc.(w/o sash bars)edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc.as spcd. Clause 8.20(a) complete asll as specified and directed by Engr-in-charge.

S&F for 2nd class hard wood 35 mm thick plain framed panelled factory made shutter two panels with lock rail and panels or 9mm BWP commercial ply or 12 mm veneered partical board with veneered veneering on both side size of rails as per IS-1003 kiln seasoned and chemically pressure treated comp all as specifed.

S&F 25 mm thick Flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces complete all as specified and as directed by Engineer-in-Charge.

S&F 18/19 mm thick grade 2 exterior grade commercial type board fixed with screws to timber frame work.

S&F12mm thick plywwod grade BWR , type BB , fixed with screws to timber frame work.

S&F stainless steel fancy type, bright finish handles fixed with screw, of 125 mm size all as specified.

M&L Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads section of scantling exc 13.00 sqcm and nexc 25 sqcm in section

S&F continous (Piano) hinges 30 mm wide mild mild steel bright hinges 300 width of flap mild steel bright finished or electrogalvanised

S&F Mild steel hold fast and similar small articles conforming to Fe 410-0 or Fe 310-0.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the frame at site as per specification.

S&F Butt hinges extruded alumonium alloy with galvanised mild steel hinges pin anodisedand fixed ,type B-21 of 100mm.

S&F Butt hinges mild steel medium weight cold rolled of 100mm.

S& F Aluminium anodised barrel tower bolt of extruded section of 150 mm

S&F Aluminium locking bolts, anodised, with bolt not less than 10mm dia 100 mm size complete all as specified

S& F Aluminium handles cast type anodised of 150mm

S&F mild steel barrel tower bolt ,stove enamelled black with bright bolt of 150mm

S&F mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with and incl. A minimum of 6bolts and nuts four on bolt plate and two on staple plate of 250mm long.

S&F mild steel pressed handles oval type stove enamelled black of 150mm

S&F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15mm complete all as specified and directed by Engineer-in-charge.

S&F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20mm complete all as specified.

S&F mild steel pressed handles oval type stovew enamelled black of 150 mm

S&F 300 mm ordinary mild steel rat tail rod pattern springs, incl roller and roller plate complete all as specified and as directed

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length or cover plate 150 mm complete.

M&L for stainless steel wire cloth 0.56 mm nominal dia of wire and avg width or aperture 1.40 mm fixed with stainless steel wire staples.

M&L for granite 20 mm thick (Table rubbed and polished) in steps, jambs, pillars, window, cills, cooking platforms and like in cement mortar (1:4), 15 mm thick incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade or Markrana white type including moulding, rounding edges complete.

Cutting chases,pinning in making good to facing where requried and pointing in cement mortar 1:3 to ends or edge of landings,steps,cills,sunshade,shelves, lintel etc. tubes or concealed conduit etc. and making good, cutting not exc 10 cm girth

Supply & Fixing vitreous china wash down water closet (squatt pan ) white orissa pattern size 580X440mm with integral foot rest (excluding flushing cistern and flush pipe) Fixed in repairs .

S&F sinks with drainage board made of stainless steel 1.00mm thick sheet for kitchen with plug washer waste pipe , mild steel brackets connecting union over all size915x460mm with bowl size 410x330x160mm but fixed in repair incl removing existing vitreous china sink with fittings.

M&L Vitreous china wash hand basin, white flat back, size 580x450 excluding traps waste pipe fixed with bracket fixed in repairs. Complete all as specified and as directed by Engineer-in-charge.

S&F in Repairs Brass CP single lever w/0 pop up waste system mixer for mixing hot & cold water screwed down for iron pipe and fixed complete Cat Part No. 6651 of Parayag or equivalent in Jaquar, Cera and Parryware.

S&F Stainless steel soap dish Parayag Cat Part No:-BA-05 or Equivalent in CERA,Parryware,JAQUAR

S&F Corner Glass shelf 200 mm with and including brackets & SS screws Prayag CAT Part No. BEA-42 or equivalent in cera,jaquar,parryware.

Supply and fixing PVC valve less, symphonic action type, flushing cistern, low level white with inlet, ball valve, float and handle including brackets 10litres complete

S&F PVC connection 15mm size with PTMT nuts of length 450mm.

S&F Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm fancy type chromium plated concealed type fixed in repair

S&F Shower Arm 15mm bore size ,225 mm long arm with flange . CAT PART :- BS-65 of PARAYG or equivalent in Cera , Parryware, Jaquar.

S&F Towel rail of cast copper alloy, chromium plated, fixed in repair complete all as specified and directed by Engineer-in-charge. CAT PART NO.:-BA-20 of PARAYAG or Equivalent in Cera,Jaquar or Parryware.

S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm Make : Prayag or equivalent.

S&F Waste pipe 40 mm for SINK with coupling fixed in repairs.

S&F bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed CAT PART NO:-6606 of PARAYAG or Equivalent in CERA,JAQUAR,PARRYWARE.

S&F Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm fancy type chromium plated concealed type fixed in repair CAT PART NO. 6618 OF Parayag or Equivalent in Cera,Jaquar,Paryware.

S&F Rotational moulded polythene water storage tank (cylindrical vertical with closed top) double layered ISI marked hoisted and fixed in position of 500 ltrs incl dismantling.

Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm Make : Prayag or equivalent.

S&F 20 mm gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes and fixed, completed all as specified.

S&F in Repairs Vitreous china wash down water closet pan (pendestal pattern), white (excluding fixingbolts, flushing cistern and flush pipe) complete all as specified and as directed by Engineer-in-Charge

S&F 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete.

S&F Stop valves, cast copper alloy fancy type, high pressure, screwed both ends for 20 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge, Parayag cat Part No :- 7310, Jaquar Essco Cat Part No -TQT-256 (Equivalent in Jaquar/Cera/Parryware/Marq)

S&F 22- 25 mm thick machine cut kota stone slab as in flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing,& complete all as specified and as directed by Engineer-in-Charge.

M&L Makrana doogri work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana white type

S&F Mild steel framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0

M&L 4-5cm thick sand stone slabs in shelves, chajjas, shelves etc n exc 2m in length set and pinted in CM 1:4

M&L for 40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in plinth protection complete ass as directed

M&L roughly squared stone lintels, beams, hammer dressed on face and soffits, hoisted, set and pointed in CM 1:4 complete n exc 3m in length.

Dimantling pipes of any desc.fixed to wall or laid under floor

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches all as specified.

All as per srl item No 111 above but 75mm bore pipes ditto.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls duly apply a coat of bitumenous black paint complete all as specified and directed.

All as per srl item No 113 above but 75mm bore pipes fixed to wall ditto.

All as per srl item No 113 above but 50mm bore pipes fixed to wall ditto.

S&F Cast iron work in lids for oval access doors for 75mm bore pipes and fittings including all necessary threading and nut/bolt required as directed by Engr in charge.

S&F Cast iron work in lids for oval access doors for 100mm bore pipes and fittings including all necessary threading and nut/bolt required as directed by Engr in charge.

S&F Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door. all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door.

M&L for Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joints for 75 mm bore

M&L for Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joints for 100 mm bore

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore pipe.complete all as specifiecd and directed.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore pipe.complete all as specifiecd and directed.

S&F Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 50 mm bore complete all as specified.

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 75mm bore (fixed in repairs)

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 100mm bore (fixed in repairs) all as specified.

S&F cast iron vent cowl for 50 m dia pipe. all as specified.

S&F cast iron floor trap 75 mm, with grating including jointing to waste pipe . all as specified.

S&F Brass chromium plated shower rose 100 mm size with 225 mm arm fixed complete all as specified and as directed by Engineer-in-Charge, Parayag Cat Part No-BS-73 or equivalent in Jaquar/Parryware/Marq

S&F Towel rail 600 mm long or cast copper alloy, chromium plated fixed in repair complete all as specified and directed by Engineer-in-Charge.

M&l Vitreous china wash basin, white flat back, size 515x410mm excluding traps waste pipe fixed with brackets fixed in repairs. Cera Cat Part No - S2040121 or Eqv. In Johnson/Parryware/Hindware

S&F Waste pipe 32mm for WHB with coupling fixed in repairs.

S&F sinks with drainage board made of stainless steel 1.00mm thick sheet for kitchen with plug washer waste pipe, mild steel brackets connecting union over all sized 915x460mm with bowl size 410x330x160mm but fixed in repair incl removing existing vitreous china sink with fittings

S&F Waste pipe 40 mm for SINK with coupling fixed in repairs.

S&F Bib taps cast copper alloy cromium plated CP long body with crutch or butter fly handle screwed for iron pipe for 15mm bore dia of pipe fixed in repair (Fancy Type) Parayag cat Part No - 7308, Jaquar Essco cat part No- TQT512 or Equivalent in Jaquar/Cera/Marg/Parryware.

S&F Bib taps cast copper alloy cromium plated CP short Body with crutch or butter fuly handle screwed for iron pipe for 15 mm bore dia of pipe fixed in repair (Fancy Type) Parayag cat Part No - 7306, Jaquar Essco cat Part No TQT 511 Or Equivalent in Jaquar/Cera/Marg/Parryware.

S&F soap dish make Parayag Cat No BA-15G or equivalent in Jaquar/Cara/Parryware

S&F Stainless steel Peg set complete all as specified and as directed by Engineer - in - charge

Supply only cast iron 'P' trap 100mm dia

S&F PVC(SWR) pipes working pressure 6 Kg/sqcm single socketed in any length with rubber ring joint fixed with wall of 110mm as in rain water pipe

S&F PVC SWR junction single, (single T) equal or unequal working pressure 6 Kg/sqcm 110mm

S&F PVC(SWR) bends any radius 110mm.

S&F PVC floor (SWR) floor trap 75mm incl CP grating (Flat slotted with frame Round/Square with or with out waste hole) complete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) pipes Single socketed in any length with rubber ring joint fixed with wall of 75mm including taking out existing pipe.

S&F PVC (SWR) bends any radius 110mm with owal access complete

S&F PVC (SWR) bends any radius 75mm oval access complete

S&F PVC SWR Junction single T equal or unequal 110mm

S&F PVC SWR Junction single T equal or unequal 75mm

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bond distemper incl a coat of primecomplete all as specified and directed

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of alkaili resistant primer complete all as specified and directed

M&L curtain rails Stainless steel fancy type incl brackets stops fixed in repair .

S&F Stack clamps of bore dia 100mm /110mm out of 50mm by 5mm flat iron and 16 mm dia round iron stays , including bolt and nuts and securing ends of stays to wall or roof

M&L Preparing surfaces of plaster or unplaster new and applying three coat of white wash on ceiling

M&L Prerparing old decorated surfaces plastered/unplastered by brooming down etc and applying one coat of white wash on ceiling complete all as specified.

M&L Preparing new decorated surfaces plastered/unplastered by brooming down etc and applying two coat of distemper oil emulsion on walls inner site including cornices pilasters etc complete all as specified.

M&L complete removal of white wash of old plastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint white or tinted over & including a coat of alkali resistant priming paint complete all as specified..

M&L Complete removal of existing treatment of walls and applying two coat of cement base paint (Ist quality) in plain pattern on walls and over a coat of alkali resistant priming paint complete all as specified.

M&L preparing new surface of wood of any desc over 10cm width or girth and applying two coats of synthetic enamel paint .over pink primer

Ditto as per srl item above but one coat

M&L preparation of new steel surfaces and applying two coats of synthetical enamel paid over a coat of red oxide.

Ditto as per srl item above but one coat w/o red oxide .

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete.

M&L for broken stone or boulders Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L for 75 mm thick PCC (1:4:8), type D2 using 40mm graded stone agg as in sub base of floors etc finished even and rough complete all as specified and directed.

M&L Sand cuhsioning under floors complete all as specified and as directed By Engineer-In-Charge.

M&L for Machine pressed precast concrete interlocking paver block any colour, shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and as directed by Engineer-In-Charge.

M&L for PCC (1:4:8) type D2, using 40mm graded stone agg as in mass filling and foundaton complete all as specified and directed.

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even complete.

M&L for Preparing new plastered or unplastered surfaces of walls and applying three coats of white wash complete.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.

Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed.

Taking down old U/S existing DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC concealed conduit with accessories with laminated top cover fixed on MS sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge Make-Havells /POLYCAB/PLAZA.for the following :- (a) One Light/fan/ex-fan/Bell/point controlled by one switch.

(b)One pin 5 amps socket point on the same board with other switches complete

(c) One 3 pin 5 amps socket on independent board.

all as per item No 169 above but with 4.0 sqmm copper wire for 3 pin socket outlet 15 Amp on independent board complete and all as directed by Engr-in-charge.Make-Havells /POLYCAB/PLAZA

S&F switch piano type, 5 Amp, single pole one way, 230 Volts, flush type complete all as specified and as directed by Engr- in -charge.

M&L Switch piano flush type single pole, one way 15 Amps 230 Volts complete all as specified & directed by Engr-in-Charge.

M&L socket outlet 3Pin, 5 Amps flush type 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 Pin, 5 & 15 Amps, 230 Volts t complete all as specified & directed by Engr-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

supply and fixing fan regulator electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

supply and fixing Bell push, flush type, 5 amp 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

supply and fixing Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed by Engr-In-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Removing and refixing LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings with LED bulb 9watt

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

S & F MCB SP, 6-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB DP,D CURVE 40 Amps , 240 volts, complete all as specified and as dircted by Engr-in-charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S&F MCCB 63 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

M&L for submain wiring using 2 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 2runs of 6 Sqmm of voltage rating 1100V for Single phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-2 runs of single core FRLS PVC cable 6sqmm for Single phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)

Taking down and refixing tamper proof energy meter electronic type single phase 10-40 Amps current rating single phase 230V AC with electric connection and necessary fixing arrangement and Preparation of surface of the old panel/meter box and painted with two coats of synthetic enameled paint over one coat of red oxide primer complete all as specified and directed.

Taking down cealing fan, cable ,dismantling blades and removing fan and blades & refixing ceiling fan of any make, any sweep , keeping side in store in safe custody for painting of ceiling fan complete,in situ with painted with two coats of synthetic enameled paint over one coat of red oxide primer synthetic enamel paint by spraying including filling cavities with filler ,after cleaning all dust and reassembling the fan complete including writing MES No at the site.

Removing and refixing water heater storage type, puff insulation type of 25 ltrs capactiy and 1500 watts, BEE Star rated-5, with glass line inner shell with Hot & Cold pipe, water connection pipe, electric connection and necessary fixing arrangement complete all as specified and directed.

S&F MCCB TPN DB,4 way Vertical type,440V,3 phase with rated busbar 100 Amps, double door type suitable for MCCB as a incomer and MCBs as out going double door type ,grouted in walls with Fixing arrangemant complete all as specified and directed. Make-Legrand cat No-5077 50 or equivalent in C&S,Havells

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth using galvanised iron strip 25×4mm as earthing lead by means of bolts, nuts check nuts and washers of galvanized iron and earth strip protected by provision of GI mediumgrade pipe 40mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m width for laying of cable lines and pole etc and getting out in hard/ dense soil complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified.

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-charge.

Supply and laying Sand coarse dry as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 cm (15 cm under the cable & 8 cm over the cable) all complete as specified and as directed.

Supply and laying bricks (old size) for cable protection by using common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry flat across length of the cable and all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed.

M&L for GI tubing 40 mm dia light grade with all necessary flxed to walls, poles, under road/floor etc for cable protection complete all as specified and directed.

SHREE GURU NANAK CONSTRUCTION COMPANY

Beenu Co. Company

vipul construction company