Terrace Waterproofing work Guest Room Leakage Treatment Basement Leakage Treatment Concrete Road Office Room Leakage work and Miscellaneous Civil Repair works at Goregaon Depot Building and Premises Balbharati

Amount

Miscellaneous Civil, Waterproofing, Plumbing & Sanitary Work

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc.

Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc. complete.

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete.

Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete.

Waterproofing Treatment to existing Terrace by using Polymeric cementitious membrane of approved make & approved by Engineer in charge by replacing the existing waterproofing treatment. Break open the existing I.P.S. and brick bat coba of the terrace slab to expose the bare slab. (If there are cracks on the bare slab open the crack in V Groove and fill it with P.M.M. and if there are lots of honeycombs and identified bad patches of concrete the same should be grouted by grouting procedures). Clean the entire surface thoroughly and over this prepared surface, apply three coats of polymeric waterproofing coating having a breathable non toxic acrylic polymer liquid of approved make & approved by Engineer in charge, over this waterproofing treatment, provide and lay brick bat coba of average 112 mm thickness.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.)

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc). Spec. No. Bd. F.3 Page No. 298 and B.7, Page No. 38

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)Spec. No. Bd.F.5 Page No. 300 And B7, Page No 38. Ground Floor

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) Spec. No. Bd.F.6 Page No. 300 and B.7, Page No.38

Providing and laying in situ cement concrete M -30 with tremix treatment for 200 mm thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4 mm wide and 20 mm deep with necessary refilling with polysuphide sealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter ( excluding reinforcement) with coarsen and fine aggregate Using V.S.I.Quality Artifitial Sand etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.. Spec. No. MORTH 602

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec. No. Bd.F.17 Page No. 306.

Providing and constructing masonry in Autoclaved Areaclaved (Celluar) Concrete Block of aproved manufacturer confirming to IS 2185 Part III 1984 of size (625 x 240 x 100)mm in extra fine jointing mortar of fixoblock of Ultra Tech or equivalent in half brick thick wall including 2 hoop iron strips 25mm x 1.6mm at every third course,properly bend and bonded at ends scaffolding racking out\ joints and watering compete. Spec. No As director by engineer incharge. Ground Floor

Providing and applying gypsum plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. Spec. As directed by Engineer in charge.Ground Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc. complete. Spec. No. Bd. L.7 Page No. 369

Providing and laying machine cut machine polished kota stone flooring 25 mm to 30 mm thick and required width in plain / diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. Spec. No. Bd.M.3 Page No. 380

Providing and laying in position flooring of telephone black / Amba White / Cat Bary Brown / Ruby Red / Ocean Brown Granite Stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. Spec. No. Bd.M. 3 B/Page Number 380

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. Spec. No. Bd.C.2 Page No. 275

Providing & fixing colour coated Zincalume ( R ) AZ150 ( min 150 gm / sqm total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) ( o.5 mm TCT ), Hi-strenght steel with min 550 MPa yield strength, metallic hot deep coated with Alluminium Zinc Aalloy ( 55% alluminium, 43.4% Zinc, 1.6% Silicon) with colourbond ( R ) steel quality super durable polyster paint coat ( with inoraganic pigment ). The paint shall have a total coating thickness of nominal 35 um, Comprising of nominal 25 um exterior coat on top surface & nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width & nominal 25 - 30 mm deep ribs with subtal square fluting in the five pan at nominal 180 - 250 mm center to center. The end rib shall be design for anti -capillary groove. & return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated Hex head

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. Spec. No. BD-T-34 Page Number 499.

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating / clour anodised as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. Spec as directed by engineer in charge.

Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bott m track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box Spec as directed by engineer in charge.

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete. Spec. As directed by Engineer in charge.

Providing and applying priming coat on concrete/ masonary / asbestos cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete. Spec. No As director by engineer incharge.

Providing and applying impression 24 carrat Luxury paint of approved make & approved brand Emulsion paint to interior walls and ceilings of approved quality, colour and shade to new surface in two coats, including sub surface prparation by Acrylic putty and Acrylic primer coats including scaffolding, preparing the surface. etc. complete (Low VOC).. Spec. No. As directed by Engineer in charge.

Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete. Spec. No. Bd.O.5 Page No.405.

Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complet. Spec. No. As directed by Engineer in charge.

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing and fixing frame work of anodised aluminium sections for suspended false ceiling consisting of aluminium T 50 mm x 40 mm weighing 0.39 kg/m. at 60 cms c/c and fixed with ( 15 x 15 mm) flanges weighing 0.119 kg/m suspended on 6 mm dia. mild steel rod weighing 0.22 kg/m fixed on wall and beams including rounding of the edges with aluminium T of 50 mm x 40 mm weighing 0.39 kg/m etc. including all labour etc. complete.

Providing and fixing false ceiling of 10 to 12 mm thick decorative boards of fibrous plaster of paris including scaffolding if necessary all architectural work like mouldings, cornices, coves, domes, cups as per detailed drawings and three coats of spray painting to boards etc. complete. (excluding frame work, runners and mild steel suspenders).

Providing and fixing European type wall-hung white water closet of approved make with push valve concealed type with cover plate 32mm size of approved make including soil pipe, vent pipe up to outside face of wall ,100mm dia.

providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated

Providing and fixing white glazed urinal of size 710x460x300mm with sensotronic concealed type flushing valve for urinal with complete kit having fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32mm

Providing and fixing 10 cm PVC nahani trap with grating etc. complete

Providing and fixing C.P. pillar cock long neck with aerator of approed make including necessary sockets/union nut etc. complete.

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking

Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking

Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing,laying and fixing P.V.C. pipe of 40 mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and

Providing ,laying and fixing P.V.C. pipe of 75 mm dia. with fitting ssuchas bends, tees, reducers, clamps, etc.including necessary excavation, trench filling etc. complete. Including removing existing pipeline if necessary and

Providing , laying and fixing ,jointing Eco- drain 110 mm SN 8 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees, coupler, etc,

Providing , laying and fixing ,jointing Eco- drain 160 mm SN 4 Nu- Drain Upvc pipes or of equivalent make, manufacture as per EN 13476 or equivalent as per I.S.15328 with fittings such a bends, tees , coupler, etc,

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside

Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete.

Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete.

Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete.

Providing and fixing Glass self 125 mm wide and 600 mm long with necessary chromium plated brackets providing T.W.gutties etc. complete

Providing and applying 6 mm Thk Self Levelling Epoxy Flooring System to form a Joistless, Sami glossy Finish flooring. All including proper surface preparation to remove all dust, laitance on the floor. Filling up of Cracks, Joints if any on the CEMENT TILES flooring. Cutting grooves in the Concrete at the periphery of walls, columns for anchoring. Application of Epoxy Putty, primer coat of FLORPRIME EP followed by 4mm thk LANKO 731 CEMENTIOUSES screed strength of M48 in layer and followed by Top Coat strength of FLORGARD SL 2000. With inter coat interval as per manufacturer’s instruction (MSRTC Rate Attached)

C.P.Toilet paper holder

C.P.Soap dish hooker jaquar make continental

C.P.sink mixer swinging spout (table mounted model) 450mm long braided hose

Providing, laying and fixing exterior grade fibrilling fibre reinforcement heavy duty designer cement concrete tiles for Flooring of approved colour and design 22 +/ -2 mm thick bayer colour pigmented as per IS ..1237 - 1980 having compressive strength more than 500 Kilogram/sq.cm reaffirmed in 2006 ,having wert transvrse strenghth of 3.5 / mm 2, water absorption less than 10 % abrasion / wear resistance less than 2 mm ,skid resistance more than 25.0 (ASTM:E303) and no fading as per DIN - 51094 of size 300 x 300 in plan / designed pattern on a bed of 1:4 cement mortar including cement float ,filling joints with neat cement slurry ,curing, polishing and cleaning etc. complete. For flooring.

Providing and laying telephone black / Amba White /Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Transportation of debris upto 5km including transportation, loading & unloading from site to stackyard

Lowering down the debris obtained from breaking and removing the cement plaster / burnt brick masonry of the first floor by any means without causing dust nuisance and damage to structure, stacking the same as and where directed including cleaning the site complete.

Furniture & Interior Works

Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric &telting with chain (Ball) system with all necessary fixtures and fitting etc.complete. (Sample to be final by Engineer In-charge prior execution of work)

Providing and fixing Veneer/wooden finish PVC wall Panelling plank including fixing including all lead and lifts complete as per Architects Drawing and instructions of Engineer Incharge.

Sofa Set 3+1+1 Providing &fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 Kilogram) Seating Capacity: Five Seat

Bed Side Table @ 400LX 400DX 415H Providing and Fixing Bed Side Table of size 400LX 400DX 415H The bed side unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The bed side table has one drawer and one shelf. The shelf is made of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding

Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mm X 750mm X 450mm With 12mm Thick ColourEitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc.

Dressing Table @400LX 400DX 1800H Providing & Fixing Dressing Table of size 400LX 400DX 1800H.The Dressing table unit is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The unit has one drawer and one shelf. The dressing table has a mirror of 4mm thick pasted on 18mm thick prelm particle board attached to the base unit. The mirror size considered is 1155 x 360 x 4(t). The mirror has been pasted using high quality 3M sticker. Item No. 51.56

Wardrobe with Mirror @ 900LX 600DX 1965H Providing and Fixing Wardrobe with Mirror of size 900LX 600DX 1965H The wardrobe side panels and doors are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The shelves are made of 18mm thick Prelam Particle Board with decorative laminate on both sides. The top is made of 36mm prelam particle board with decorative laminate on both sides. (18mm Prelam Particle board and 18mm batons on all sides to achieve 36mm overall thickness). The exposed edges of the top are sealed with 2mm thick PVC edge Banding. The top most part of the wardrobe has an aluminum hanger rod of EBCO make. One drawer of size 400(W) x 150(H) x 450 (D) made of 18mm thick prelam Particle Board has been considered. The drawer will have a multipurpose lock of EBCO premium make. The wardrobe handles are Satin SS finish of 160mm pitch. The wardrobe has a multipurpose lock of EBCO make. All hinges considered are Hettich make. Necessary good quality hardwares have been considered as required.

King Size Bed @ 1800Lx1800Dx650H Providing and fixing of king size Bed of Size 1800Lx1800Dx650H with matress and pillow. Understructure: - The bed box side pannel are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding with bed back made up pf 18 mm thick prelamintaed particle board.

Supply and fixing of Door Mat of high quality for Guest Rooms.

Supply and providing of SS High Quality Dustbin for Guesthouse.

Providing & Fixing in position, Carpet more than 800+ gsm, made with 100% stainproof fibre sofa pproved make along with 5mm under laya sper Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour, finishing etc complete

Single Bed @ 2025LX 1000DX 650H Providing and fixing Single Bed of Size 2025Lx1000Dx650H with matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2 mm. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT.Side Panel: - The side panels are made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The overall width of the side panel is 150mm. The side panels have 18mm thick prelam particle board Baton running for required length to add rigidity to the structure. Head Board :- The head board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 650mm. Foot Board :- The foot board is made up of 18mm thick Prelam Particle Board with both side decorative laminate. All exposed edges are sealed with 2mm thick PVC edge Banding. The head board size to be considered as 1000 x 450mm. Bed Base: - The Bed Base is made up of 12mm thick Prelam Particle Board with both side White laminate.

Electrical

Point wiring for light/fan/bell concealed type in min 20 mm PVC conduit with 1.5 sq.mm. FR grade copper wires with moduler type switch and required accessaries as per specification No: WG-PW/CW (upto 6 mtr) (point above 6

2-way Light Point:- Point wiring for light/fan/bell concealed type in min 20 mm PVC conduit with 1.5 sq.mm. FR grade copper wires with moduler type switch and required accessaries as per specification No: WG

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm PVC conduit with 1.5 sq.mm. (2+1E) FR/FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW

Wiring for plug on board with Switch socket concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete. (for AC socket-8)(TF-AC-12)

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to

Supplying and erecting modular type switch 16A ISI mark approved make duly erected on provided plate and box with wiring connections complete.(power-7)(TF-3)

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to

Supplying and erecting modular type switch 6A / 10A ISI mark approved make duly erected on provided plate and box with wiring connections complete. (COMP P- 4,IP(1X1)-6) (CP-22

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete(COMP P-4,IP(1X1)-6) (TF-CP-22

Supplying and erecting ISI mark modular type D.P. switch 32A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular typeT.V. socket single outlet ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type telephone socket one gang with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting moduler type Electronic type step regulator two module complete erected on provided plate and box with wiring connections complete. 4 fan

Supplying & erecting mains with 2x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW (bunch of wire for

Suppling & laying Rigid PVC conduit 25 mm Dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC, para no. 1.2.1 (for Light point wire above 6 mtr extra circuit).

Suppling & laying Rigid PVC conduit 20 mm Dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC, para no. 1.2.1 (Telephone wiring). (Concealed

Supplying & erecting mains with 2x1.5 Sq.mm and earth wire 1.5 sqmm FR PVC copper wire in rigid PVC conduit min. 20mm dia. as per specification No: WG-MA/PC. (for Switch board circuit) (Concealed

Supplying & erecting mains with 2x2.5 Sq.mm and earth wire 1.5 sqmm FR PVC copper wire in rigid PVC conduit min. 20mm dia. as per specification No: WG-MA/PC, para no. 1.4.1 (for power & IP board circuit) (Concealed

Supplying & erecting mains with 2x4.0 Sq.mm and earth wire 2.5 sqmm FR PVC copper wire in rigid PVC conduit min. 20mm dia. as pern specification No: WG-MA/PC, para no. 1.4.1 (Concealed)

Supplying & erecting mains with 4x4 sq.mm.and earth wire 2.5 sq.mm FRLS PVC copper wire, in rigid PVC conduit 25mm dia,as per specification No: WG-MA/PC, para no. 1.4.1

Supplying & erecting mains with 4x6 sq.mm.and earth wire 4 sq.mm FR PVC copper wire, in rigid PVC conduit 25mm dia, as per specification No: WG-MA/PC, para no. 1.4.1 (Concealed) (Lay Copper unarmoured cable instead

Supplying & erecting mains with 4x10 sq.mm.and earth wire 6 sq.mm FR PVC copper wire, in rigid PVC conduit 32mm dia, as per specification No: WG-MA/PC, para no. 1.4.1

Supplying, erecting & terminating XLPE armoured cable 3½ core 35 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole

Making the trench in soft soilof suitable width and depth as per IS for laying provided L.T cable of 25 sq mm & above and covered with Half round hume pipecomplete. As per specification no. CW-EXNCTR

Supplying and erecting flat flexible 3 core 4 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying and erecting Five Star Rated Energy Saving Ceiling Fan230 V A.C. 50 cycles 1200 mm complete erected in position as per specifcation no. FG-FN/CF.

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia. or equivalent square

Supplying and erecting ‘B’ grade G.I.pipe/M.S. pipe down rod duly painted for fan complete erected with PVC two core flexible cable 24/0.2 mm copper PVC wire.(2m for each fan)

Supplying and erecting fresh air cum exhaust fan of light duty250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner..

Supplying and erecting Iron, sheet metal work consisting of CRCA Sheets, Various sections of iron, Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending,

Supplying and erecting LED square / circular 9 to 12W down lighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erectingCorridor/Passage light fitting( 2 feet) including 9W LED lamp, Comprises of Extruded channel in Plastic Silver grey Color & With same Plastic end cap on provided PVC block / wooden board

Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting street light Wall bracket made from 40 mm. dia ‘B’class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB

Supplying and erecting LED street light fitting suitable above 26W to 36W lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium

Supplying, erecting & marking SPMCB 6A to 32A (C- Series power/ TV/ Switch board with skt, D- for AC/Geyser) in provided distribution board as per specification No. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A (B- series for Lighting switch board without skt) in provided distribution board as per specification No. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification No. SWSWR/ MCB

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6A/10A/16A/20A/25/A

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 63A as per specification

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per

Supplying, fixing and commissioning 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per

Supplying & erecting triple pole and neutral distribution board (TPNDB)with double door surface/ flush mounted SPMCB of12 ways, on iron / G.I. frame /wooden board. (Horizontal type) as per specification No. SW

Supplying & erecting triple pole and neutral distribution board (TPNDB)with double door surface/ flush mounted SPMCB of24 ways, on iron/ G.I. frame/wooden board. (Horizontal type) as per specification No. SW

Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted SP / TP of 24 ways on iron / GI frame (vertical busbar type)as per specification no. SW-SWR/MCBDB(6 way MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted suitable for 3 pole MCCB as incomer & outgoing SP MCB (24 poles) or TP MCB of 8 ways (24 poles) , on iron/ GI frame.

Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 6 ways for outgoingSP MCB’s on iron/ G.I. frame/wooden board as per specification No. SWSWR

Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of

Supplying, erecting & marking TPMCB 6 A to 32A in provided distribution board as per specification No. SW- SWR/MCB (25A-5)

Supplying, erecting & markingTPMCB 40A to 63A in provided distribution board as per specification No. SWSWR/ MCB (40A-1,63A-2)

Supplying and erecting aluminium strip of required sizes used for earthing on wall and/or any other purpose with necessary aluminium clamps fixed on wall painted with bituminous paint in an approved manner with joints

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/centrifugal pump set upto 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/voltmeter, phase

Supplying &erecting 16 amp. 3 pin plug Top bakelite type of 230 V.A.C. supply.

Supplying, Fixing, testing and comissioning of 43” LAED SMART TV with 4K Ultra HDR (3840X2160), having 3 HDMI ports, 2 USB ports, 20 Watts Dolby Digital Plus Adaptive Sound Output. Including all leads, lifts, fixtures, fasterners, etc. complete. as directed by Engineer In-charge Approved make: PANOSONIC /LG /SONY/MI

Supplying, erecting, testing and commissioning Electric Water Kettle with 1.5 liter capacity, 1350 watts power, stainless steel body, Auto cut off, boil dry protection and cordless serving. Including all leads, lifts, placing, etc. complete. As directed by Engineer In-charge. Approved Make: - INALSA, Havells, Bajaj, V-Guard.

Supplying, installing, testing and commissioning split type variable speed inverter technology room Air conditioning unit 1.5 TR capacity having ISEER minimum 4.50 suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall/ floor mounting type complete.

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 16 mm complete.

Aziz and Associates (India) Pvt.Ltd

M/s Malani Combines

Stratum Consultancy Services Private Limited