ANNUAL REPAIR AND MAINT OF SRU DALHOUSIE UNDER GE (AF) PATHANKOT

Amount

Dismantling corrugated asbestos /translucent/fiber sheet in roof covering including rIdges complete all as specified and directed by Engineer-in-Charge.

Supply and fixing corrugated fiber glass reinforced transcluent sheeting of any thickness with two corrugated sheeting with two corrugated side lap fixed with l-type or j type or cranked hook in liew of screw complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 0.63mm thick galvanised, corrugated mild steel sheeting with two corrrugations side lap, fixed with coach screws and washers, in roofs, wall etc. with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Fe 410-w(Gde E 250)quality B rolled mild steel in roof trusses (framed) trussed, purlins, crane gantries, rails and framing (beam, tee, angle, channel or flat sections) including distance pieaces cleats complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Fe 410-w(Gde E 250)quality B MS plates plain or chequered square cut or notched forming holes drilled or welded any thickness complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new steel and iron surfaces of any description over 10 Cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer over a coat of moderant solution to remove zinc coating complete all as specified and directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface, work in hard dense soil complete all as specified and directed by Engineer-in-Charge.

Material and labour for 1:4:8 type D2 using 40 mm graded crushed aggregate as in foundation filling or mass concerete complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick wall upto any height and ceilings including raking out joints hacking for key srcubbing down with water complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour 5 mm thick cement plaster in cement mortar 1:3 on celings, surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces and applying two coats of exterior acrylic paint of any shade as approved by GE as per manufacturers instruction complete all as specified and directed by engineer in charge.

Material and labour for Complete removal of existing treatment on walls and applying two coats of exterior acrylic paint of any shade in as approved by GE as per manufacturers instruction complete all as specified and directed by engineer in charge.

Material and labour for Preparation new surfaces of wall and applying two coats of oil emulsion distemper over a coat of 3 mm thick wall putty complete all as specified and directed by Engineer-in-Charge.

Material and labour for Preparation of new surface of ceiling and applying two coats of Oil bound distemper over 3mm thick wall care putty complete all as specified and directed by Engineer-in-Charge.

Material and labour for Preparation of old decorated wall surfaces and applying two coats of Oil bound distemper on walls over 3 mm thick wall care putty complete all as specified and directed by Engineer-in-Charge.

Material and labour for Preparation of old decorated ceiling surfaces and applying two coats of Oil bound distemper over 3mm thick wall care putty complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel and iron surfaces of any description over 10 Cm width or girth not otherwise described and applying two coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

Material and labour for preparation of old decorated surfaces of wood of any description not otherwise described over 10cm in width or girth and applying two coats of Synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutters (with out taking off the shutter from the frame ) exc 1.5 sqm but ont exc 4 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frame with shutters (with out taking off the shutter from the frame ) n exc 1.5 sqm each complete all as specified and directed by Engineer-in-Charge.

Supply and fixing steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60x25mmsingle rebated comprises gauged skelton shutter ERW sec 50x20mm and 1mm thick with two open able leaf consisting two Nos sash bars of T section 20x3mm completed welded to frame with one vertical mullion of ERW box type T section of size 60x25mm and 1.25mm thick including cutting holes and making good dismantled portion PCC 1:2:4 type B1 four Nos for each window incl following fittings weld to frame shutter (a) hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window (b) handle of Z sction 20x25mm, 100mm long 01 Nos per leaf (c) MS Tower bolt 150mm long of 12x3mm made to shape-04 Nos per window (b) handle of Z section 20x25mm, 100 long stoper-01 No per leaf () MS pintal of hinges of size 75mmx12mm-02 Nos per leaf (g) fabrication and fixing arrangement as per direction of Engineer-in-Charge. Note : wire mesh and painting shall be measured and paid separately under appropriate item complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Pressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC type C-0 (1:3:6) using 12.5 mm graded stone aggregates as in filling of MS sheet chowkats complete all as specified and directed by Engineer-in-Charge.

Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-Charge.

Supplly and fixing 35 mm thick plain framed panelled shutters (two planel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of the rail and stile as per IS:1003(Part I), kiln sseasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

Supply and fixing galvanised mild steel wire clothes 0.56 mm nominal dia of wire and average width of aperture1.18 mm in repair complete fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engineer-in-Charge.

Material and labour for two coat of Synthetic enamel paint over a coat of pink primer on new wood surface of any description not otherwise described over 10cm in width or girth including preparation of new surfaces complete all as specified and all as directed by Engineer-in-Charge.

Supply and fixing 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 125 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 3 mm thick plainsheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm each pane complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 5 mm thick figured glass, pin had type and glazing with beads in squares n exe 0.5 sqm each pane complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair door closer hydraulically regulated made up of aluminium extruded section body universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth wall tiling (but not backing) removing servicable tiles to store rubbish off the premisses complete all as specified and directed by Engineer-in-Charge.

Material and labour 15mm thick screed bed or bedding layer of cement mortar 1:6 to laying floor finish complete all as specified and directed by Engineer-in-Charge.

Material and labour non skid ceramic colour tiles 7 to 8 mm thick joint free edge cut (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm(400mmx400mmx7 mm thick) set and jointed in neat cement slurry and pointed in colour cement to match as in floor complete all as specified and directed by Engineer-in-Charge.

Material and labour glazed ceramic colour tiles 300mmx450mm/300mm x200mm x7mm thick set and jointed in neat cement slurry and pointed in coloured cement on vertical surfaces such as skirting/dado over cement mortar rendering/screding 10mm thick 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour Machine cut kota stone slabs flooring 20-25mm thick, as in riser of steps, skirting, dado and piller laid and the including screed bed over cement slurry screed 15mm thick in CM (1:4) incl rubbing and polishing, rounding or bullnosing the exposed edges complete all as specified and directed by Engineer-in-Charge.

Supply and fixing vitrified ceramic tiles light shade double charged 10 mm thick (square/rectangular) polished area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per ser item No 42 above but in skirting and dado including , 10mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour PCC 1:3:6, type C-2, 75mm thick as in plinth protection, Surface finished fair and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for 20mm thick granite black slab, machine cut, well polished, bedded in 15mm thick in CM 1:4 as in cooking plaforms & like and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixtures of pigments to match the shade of granite stone including cutting and polishing complete all as specified and directed by Engineer-in-Charge.

Material and labour for coloured chequered cement concrete tiles 22 to 25mm thick, set jointed and pointed in neat cement slurry in floors, with grey cement and pigment except tile complete all as specified and as directed by the Engineer-in-Charge

Material and labour screed bed or bedding layer of mortar 15mm thick in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for repairing of RCC projections, chajjas , roofs, facia etc. in patches not exceeding 3 Sqm in each patch by necessary preparation i.e. scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, sufaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregate and reinforced with welded mesh of weight exc 2kg per sqmtr but n.exc 3kg/sqm with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches are n.exc 70mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engineer-in-Charge. Note:- Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the contractor.

Supply and fixing in repair vitreous china ware wash hand basin white flat back size 550mm x 400mm excl taps, waste chain and plug and porecelain stopper but incl bracket and cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC white low level flushing cistern 10ltrs capacity with all fittings syphonic action push stype with inlet ball valve and float incl PVC flush pipe, ball valve, handle, MS bracket complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC connection, 60cm long, 15mm in size with PTMT nust and PVC washers at both ends complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair CP grating doom 125 mm dia with cockroach trap fixed properly to the floor and sealed properly and finished with white complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair CP grating doom 125 mm dia with waste hole and cockroach trap fixed properly to the floor and sealed properly and finished with white cement complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 32 mm dia bore PVC flexible pipe for wash hand basiin and kitchen complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Bib taps cast copper alloy chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair pillar tap, cast copper alloy, with capstan heads, 15mm bore dia of pipe chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 15mm dia Angle cock chromium plated brass fancy type ,screwed down , high pressure, scrwed both ends for iron pipe in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair Soap dish stainless steel chromium plated fixed with brass screws and rawl plug complete all as specified and directed by Engineer-in-Charge.

Supply and fixing CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Cutting chases in brick wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engineer-in-Charge.

Taking down steel water tubing 15 mm with all fittings from walls, ceiling and floors complete all as specified and directed by Engineer-in-Charge.

Taking down steel water tubing 20 mm with all fittings from walls, ceiling and floors complete all as specified and directed by Engineer-in-Charge.

15mm GI tubes medium grade with all fittings & fixed complete to walls or ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

All as per ser item no.64.00 but 20mm dia complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks exc 500 ltr and n exc 1000 ltr and removing to store complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 500 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms)

Supply and fixing 15mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms)

Supply and fixing in repairs vitreous china wash down water closet (Pedestel patern ) white including fixing bolt, plastic water closet seat cover black/white closed pattern with flat bottom and cover and mild steel chromimum plated hinging device, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Dismantling cast iron work of any description complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110mm PVC(SWR) Branch pieces, single T (equal or unequal) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints of bore 110mm ccomplete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110mm PVC (SWR) bore Bend any radius complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints laid in tranches or in floor of bore 110mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor of bore 75mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall of bore 75mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75mm PVC(SWR) Branch pieces, single T (equal or unequal) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75 mm PVC(SWR) bore Bend any radius complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC(SWR) Vent cowls 110mm bore complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC SWR 75mm floor trap , plain with grating including jiointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work built in CM including all quoins arches pillars complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) with old size bricks complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge.

Material and labour for Cement concrete in surface channels and drains in cement concrete 1:3:6 type C1 (20 mm graded aggregate) finished even and smooth using extra cement complete all as specified and directed by Engineer-in-Charge.

Cleaning of sewer lines of various sizes by rodding from manhole to manholes 150mm dia complete all as specified and as directed by the Engineer-in-Charge

Cleaning of sewer lines of various sizes by rodding from manhole to manholes 100mm dia complete all as specified and as directed by the Engineer-in-Charge

Cleaning of manholes n exc 1m deep complete all as specified and as directed by the Engineer-in-Charge

Cleaning of manholes exc 1m deep complete all as specified and as directed by the Engineer-in-Charge

Desluding and cleaning of septic tank/manholes of various capacity and sizes and burying the sludge in a pit waste materials in borrow pits or suitable site & covering the same by spreading earth & spreading bleaching powder on it (The rates includes for making borrow pits with in 100mtr & removing, surplus soil upto 50mtr distance) complete all as specified and as directed by the Engineer-in-Charge

Roughning for old concrete surface/floor by picking, weeping clean and washing with down with water to remove dust including brushing neat cement slurry with 3.00 Kg of cement per sqm complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC 1:2:4 type B-1 as roof padding concrete to bring the extg slab in slope of 1:40 complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20kg per sqm incl cleaning surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for fixing APP based polymeric membrane minimum weighing 3.00 kg/sqm and min 3mm thick reinfirced with polyster non wove faric (wt not less than 150gms/sqm) land on primed surface by forced application complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair single bowl sinks with drain board made of stainless steel 1mm thick kitchen with plugs, washers, including bedding in cement mortar or fixing cantilever bracket and connecting union to pipe, overall size 915mmX460mm bowl size 410mmX330mmX160mm complete all as specified and directed by Engineer-in-Charge.

Material and labour for Plain aluminium sheeting 3 mm thickness ,in ridges ,hips, valley gutter complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 15mm brass CP wall Mixer for mixing hot & cold water screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing brass CP Mixer for(WHB) mixing hot & cold water screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Swan necked brass CP Mixer for(WHB) mixing hot & cold water screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Repair, maint and making the continuity of supply after rectifying the defects of the electrical items such as tube light fittings,switches, replacement of fuse wires, distribution boards, MCB (light/power), lamp holders (bracket/ pandents/ batten), bell/buzzer, push button, ceiling rose, capacitors and other similar electrical items/fittings etc. including provisioning of small pieces of electrical wire of size 1 sqmm to 10 sqmm single core and length not exceeding 0.50 mtrs complete all as specified and directed by Engineer-in-Charge Note :- (i) any accessories found unserviceable that shall be replaced under respective items of this Sch.

Supply and fixing in replacement of LED lamp 07 to 15 watt watts 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement lamp holder suitable for LED lamp of 5 to 10 watts as per site requirement complete complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of call bell electric Ding Dong type 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of Switch piano flush button type single pole one/Two way/Bell push 5 amps 240 volts complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement, for socket outlet 2 in 1, 5 pin, 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement, for switch flush type 15 Amps, 240 Volts single pole white finish complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement, socket outlet 2 in 1, 3 pin, 5 & 15 A multi purpose flush type 240 V white finish complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement switch socket combination, 5 amps 5 pin flush type, 230 volts.white finish complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement switch socket combination, 5 and 15 amps multi purpose 5 in 1 flush type, 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of ceiling rose, surface backlite, 65 x 20 mm three terminal ISI Marked complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of PVC rectangular switch Board for mounting switches, sockets etc with 3mm thick plastic laminated sheet cover of size 100mmx100mm and 50mm deep , 240 volt complete all as specified and directed by Engineer-in-Charge.

All as per item no 111.00, but of size 175mmx100mm and 50mm deep , 240 volt complete all as specified and directed by Engineer-in-Charge..

All as per item no 111.00, but of size 200mmx150mm and 50mm deep , 240 volt complete all as specified and directed by Engineer-in-Charge.

All as per item no 111.00, but of size 250mmx200mm and 50mm deep , 240 volt complete all as specified and directed by Engineer-in-Charge.

All as per item no 111.00, but of size 350mmx300mm and 50mm deep , 240 volt complete all as specified and directed by Engineer-in-Charge.

Material and labour for servicing of exhaust fan upto 300 mm sweep with painting and rewinding, change of bearing if defected, louvered/shutters including taking down and refixing after satisfactory repaired complete all as specified and directed by Engineer-in-Charge.

Supply and fixing building security light fitting of new generation energy saving and environmental friendly long life versatile pressure die cast aluminium housing IP66 LED lumanaire with high power LED 35 watt as light source with toughned glass complete all as specified and directed by Engineer-in-Charge.

Material and labour for bracket made out of GI pipe 25 mm dia medium grade, 0.9 mtr long bent to shape with welded MS flat iron clamps of size 25 x 6 mm thick for mounting of fitting with nuts, bolts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement LED tube light fitting, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver of 20 watt (4') in and including 20 watt LED tube rod complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

Supply and fixing in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Material and labour for testing of old earthing using calibrated earth tester & submitting result to engr -in -charge. Earthing which showing much more results as specified in IS rule and disconnetivity should be replaced with new earthing items are considered as below. Note : (i) Watering of earthing with 2 Buckets (30Ltrs) water mixed with salt (total 5 Kg) shall be carried out one day before the testing & the cost of the same shall deemed included in unit rate quoted.

Taking down old unserviceable/deteriorated batten/PVC conduit point wiring from existing place i.e. light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets, ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of Peris and to match / finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash complete all as specified and directed by Engineer-in-Charge.

Material and labour for surface point wiring on wall and surface on ceiling/roof with necessary fixing arrangements with PVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc with MS screw and cup washers including PVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces complete all as specified and directed by Engineer-in-Charge. (a) One light, fan, call bell, 5 Amp independent socket point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

(b) One socket point controlled by one switch on same board complete all as specified and directed by Engineer-in-Charge.

All as per item No 123 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLSH insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement of Sub main wiring with four single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 10 sqmm drawn in new/existing PVC conduit with one run of 6 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continuous earth wire complete. New PVC Conduit & cutting chasing will be measured and paid separately under relevent item here-in-after complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of Sheet metal enclosure VTPN MCCB DB 4way, 415 V (vertical type) with bus bar double door type IP 43 - IK 09 as per IEC 61439-3 suitable for flush mounting complete with 250 A copper bus bar for each phase with 2 neutral and 2 earth bus bars with cable ties for cable management for DB's when MCBs & MCCB 100 Amps (as incomer) to be used, fixed properly in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed including taking down old unserviceable DB complete all as specified and directed by Engineer-in-Charge.

All as per item No 128, but 4 way complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement MCB SP 240 volt 6 Amp to 32 Amps 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed by Engineer-in-Charge.

All as per item No 130, but SPN 16-40 Amps complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement heavy duty exhaust fan AC single phase 230/240 V of size 300 mm sweep 1400 RPM with louver & shutter including necessary grouting on wall complete and making good the wall surface after fixing of exhaust fan complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of MCCB 125 Amps, 3 Pole, 415V, 25 KA, fixed type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of MCCB 160 Amps, 3 Pole, 415V, 36 KA, thermal, magnetic adjustable type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of MCCB 200 Amps, 3 Pole, 415V, 36 KA, thermal, magnetic adjustable type complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement of Rigid metallic medium 20mm dia PVC conduit ISI marked in concealed position inclusive all fitting such as tee, bends, reducer, elbow, bell mouth, tube ends and all fixing accessories such as couplers lock, nuts, saddlers, pipe hooks etc fixed properly in concealed or surface position for laying of submain wiring or telephone wire complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of indicator lamp round/square type suitable for geyser 25/50 ltr all as per sample AC 230 Volt complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of hot and cold PVC connection 15mm dia complete with brass flair nuts at both ends. ( ISI marked and suitable for hot water supply upto 100 degree celcius.) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of brass pressure release valve chromium plated suitable for geyser 25/50 ltr capacity complete all as specified and directed by Engineer-in-Charge.

Supply and fixing anchor bolt 12mmX100mm long complete all as specified and directed by Engineer-in-Charge. Note:- Anchor bolt shall be grouted with hammer drill only.

Supply and fixing in replacement cord flexible PVC insulated and over all sheathed, 3 core, flexible copper conductor of size 2.50 sqmm, cut to size all as required at site complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement plug top 3 pin 6 amps AC 240 Volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement plug top 3 pin 16 amps AC 240 Volts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement heating element any type 1.5/2.0 KW 240 Volts, ISI marked for water heater storage type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement thermostat switch 0 to 100°C , 240 volts suitable for water heater storage type any make complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement plastic laminated top sheet cover 3 mm thick of size 5"x5" all as required at site including drilling holes for fixing screws and providing 4 Nos screws with washers for fixing the sheet to sunken box /wooden box complete all as specified and directed by Engineer-in-Charge.

All as per item No 146, but of size size 8"x5" complete all as specified and directed by Engineer-in-Charge.

All as per item No 146, but of size size 11"x9" complete all as specified and directed by Engineer-in-Charge.

All as per item no 146, but of size size 13"x11" complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of 1100 volts grade heavy duty cable PVC insulated aluminium staranded conductor , served with inner sheathed PVC tape and overall PVC sheathed in service connection one twin core flat or circular of size 10 sqmm x 2 core complete all as specified and directed by Engineer-in-Charge.

Material and labour in replacement of Earthing complete with galvanized cast iron earth plate electrode 600x600x6 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level ) with top edge of earth plate not less than 1.5 Mtr below normal ground level connected to galvanized lead wire 4 mm dia as earth lead by means of bolts, nuts washers and check nuts of steel/GI duly protected with 40 mm bore light grade pipe upto main board, 20mm bore watering pipe light grade with CI/MS funnel and wire mesh including excavation, earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoal dust and common salt as directed by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel with wire mesh complete all as specified and directed by Engineer-in-Charge.

R.K.CONSTRUCTION ENGINEERS (BID ID -3111725)

M/s Shakti Electric Works (BID ID -3124364)

Pathania Builders (BID ID -3123946)

Auto India (BID ID -3123141)

m/S Varun Gupta (BID ID -3100109)