PROVN OF 01 X GUARD ROOM WITH 3 X SENTRY POST AT LONG RANGE FC BUNDH AND PRINTING PRESS AND SPL REPAIR OF ROOF TREATMENT FLOORING PLASTERING JOINERY SANITARY FITTING AND REWIRING AT BLDG NO P 92 HAWA MAHAL IN AGE B R I UNDER GE DANAPUR CANTT

Amount

Boring holes 5m deep and 300 mm dia of pile in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50 m complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Excavation over area exc n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavation over area exc 1.5m & n.exc 3 m in depth and getting out in soft/loose soil complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

M& L ATT Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface of flooring complete all as specified and directed

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed

M&L PCC 1:4:8 type-D2 (40mm graded aggregate) as in foundations, filling and mass concrete.sub base as in floors. complete all as specified and directed..

M & L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L 40mm thick damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4, type B-0. complete all as specified and directed..

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L RCC type M-25 Design Mix using (20mm graded aggregate) as in cantilevers, bressmummers, lintels over 1.5 m span, seismic bands etc complete all as specified and directed (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to edges of concrete flats, treads, breaks in floor, window cills, concrete railing, opening in concrete wall, sides of RCC slab, RCC / PCC bends in walls or similar work thickness exc. 10 cm and not exc. 20 cm in rough finished surfaces of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note:- Liquid WPC will be measured and paid separately.

M & L Rendring 15mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L rendering 10mm thick in cement mortar 1:4 on fair face of bricks/concrete surfaces in ceiling finishing even and smooth without using extra cement complete all as specified and directed.

Supply only water proofing compound (liquid), ISI marked.

M & L for Non skid ceramic colour tiles (square / rectangular) joint free of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed (1:6) etc complete all as specified and directed.

M & L for 450x300 x7 mm thick glazed ceramic tiles (Digital pattern) including highlighter colored as in dado/ skirting and vertical serfaces set&jointed in neat cement slurry and pointed in colored cement 0ver and incl 10 mm thick cement mortar 1:4 to match the Shade, pattern, laying etc of tiles complete all as specified and directed.

Solid PVC door frame of size 50mm x47mm made out of 5mm plain clour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S & F factory made solid Panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top and bottom rail; panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, all as per specification and drawing complete all as specified and directed.

S & F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, Butt hinges, lock strike plate, etc complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-O using 12.5 mm graded crushed stone aggregate complete all as specified and directed.

S&F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, Butt hinges, lock strike plate, etc complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-O using 12.5 mm graded crushed stone aggregate complete all as specified.

S & F 35mm thick 2nd class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces , size of rail and stile as per IS:1003 (Part-I), Klin seasoned and chemically pressure treated all as per SSR complete all as directed.

S & F 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

M & L PCC 1:2:4 type B1 (20mm graded aggregates) as in bed blocks for hold fasts including necessary form works complete all as specified and directed.

S & F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks etc complete all as specified and directed.

S & F Steel ventilator with top hung shutter including, hinges, peg stay, complete all as spesified and directed

S&F Butt hinges (ISI marked), medium weight, cold rolled mild steel of size 100 mm complete all as specified and directed.

S&F mild steel, 300 mm long ordinary helical door spring incl roller and roller plate complete all as specified and directed.

S&F aluminium alloy handles, cast type anodised 125 mm long complete all as specified and directed.

S & F 100 mm size Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

S & F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S & F Aluminium handles, cast type, anodized 150 mm size complete ISI Marked complete all as specified and directed.

S & F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 250mm long complete all as specified and directed.

S & F of 150 mm size (Overall length of cover plate) floor door stopper of aluminium body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S & F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete (with glazing bars) dovetailed or welded complete all as specified and as directed.

~Ditto~ all as per item No 50.00 above but without glazing bars complete as specified and as directed.

S & F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165. complete all as specified and directed.

S & F aluminium window sliding shutter three track with following specification:- (a) chowkhat frame of size 81.25 x 38.10 x2mm thick weight not less than @ 0.781Kg/RM (b) Style/Vertical member of size 47.62 x 44.45 x 2mm thick weight not less than @ 0.667Kg/RM (c) Top and bottom rail of size 47.62 x 44.45 x 2mm thick weight not less than @ 0.667Kg/RM (d) Partialy 0.63 mm dia stainless steel wire netting mosquito proof with fixing arrangment. (e) Partialy 5.00 mm thick tinted glass fixing with rubber gasket. (f) Aluminum and PVC beading as per requirment as in fixing for paticle board & Glass, joing cleat including locking arrangement. etc

S&F mild steel conduit curtain rod with PVC coating fancy type drapery rod 20mm dia of any clour as approved and fixed with bracket complete all as specified and directed

M & L for two coats of Oil bound distemper over a coat of primer on newly plaster wall surfaces over and encluding 3 mm thick Birla / JK Putty complete all as specified and directed.

M & L Preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L Preparing new plastered surfaces of ceiling and applying three coats of white wash etc complete all as specified and directed.

M & L preparation of new steel surfaces any description, not otherwise descrived, over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M & L preparing surfaces of new wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in floor/plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete.

S & F tubes medium grade galvanised iron with all fittings & fixed complete to walls & ceiling or laid in floors 20mm bore etc complete all as specified and directed.

S & F tubes medium grade galvanised iron with all fittings & fixed complete to walls & ceiling or laid in floors 25mm bore etc complete all as specified and directed.

S&F 15 mm bore concealed type stop valves, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated, with long shank and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F shower rose chromium plated with swivel joints of size 125mm cast copper alloy CP, fancy type with CP neck 9" long made to shape complete all as specified and directed.

S & F Vitreous China wash basin white flat back size 450x300 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia,PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450 mm length with brass CP nuts on both sides, complete all as specified and directed.

S & F bib tap 15mm chromium plated fency type long body with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by the Engineer-in-Charge.

S&F 15mm dia stop valves, cast copper alloy with iron wheel head, screwed both ends for iron pipe of for unions all as specified

S&F 15mm bore angle cock, cast copper alloy CP, fency type high presure with capstan head handle, screwed both ends for iron pipe of for unions all as specified

S & F Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed.

S & F 600mmx450mmx6mm bevelled edge mirror mounted in 40mm wide PVC frame of approved size and colour on 6mm thick AC building board of commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.

S & F water closet white vitreous china ware Orissa pattern of size 580x440mm with integral foot rest ‘P’ or ‘S’ trap front or back inlet incl provision of PCC bedding type B1, 1:2:4 ( 20 mm graded aggregate) and connection pipes ( excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated) (rate also include for taking off unhygienic of WC). complete all as specified and directed.

S & F PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, low level with inlet, ball valve, float and handle including brackets incl PVC connection with CP brass nuts on both sides complete all as specified and directed.

S&F vitreous china urinals bowl type flat back, size 465 x 355 x 265 mm, white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe.

S&F CP urinal spreader for fixing with 15 mm bore pipe complete all as specified. Make : Hindustan/Parryware/Equivalent make

M&L Granite tiles 18-20mm thick machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing and incl 15mm thick screed bed CM 1:4 all as specified complete.

S & F 1000 Ltrs capacity rotational moulded polythene water storage tanks in three layer cylindrical vertical with closed top) hoisted and fixed in position incl dismantling existing tanks complete all as specified in SSR Pt-I complete all as specified and directed.

S&F ball valves high pressure of brass with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed of 20 mmdia (min weight-210 gms) complete all as specified and directed

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc of 110 mm dia. complete all as specified and directed.

~Ditto~ all as per item Ser No 78.00 above but 75 mm bore complete all as specified and directed.

S & F PVC (SWR) bends any radius of 75 mm dia provided with access door complete all as specified and directed.

S & F PVC (SWR) vent cowl of 75 mm dia complete all as specified and directed.

S & F 75 mm bore PVC (SWR) floor trap, plain with grating including jointing to waste pipe, all as specified and directed.

M & L for water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of oxidized bitumen based solvent primer @ 0.3 Kg / sqm. (iii) Applying evenly tack coat of industrial bitumen 85 / 25 grade @ 1.2 Kg / sqm. (iv) Laying unrolled over the bitumen coated surfaces polymeric water proofing membrane, hyperplas standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction. (v) Applying a coat of bituminous aluminium paint @ 100 gm / sqm over and including a coat of hot air blown grade bitumen of grade 85 / 25 @ 1.2 Kg / sqm duly sanded over polymeric membrane complete. Note:- The polymeric water proofing membrane shall be extended upto parapet walls and inserted in walls by cutting groove and making good with CM 1:3 complete all as specified and directed.

M&L for 15 mm thick screed bed in CM 1:4 with water proofing compound @ 200ml /50kg of cement as per manufacturer's instruction finished surface even and smooth with out using extra cement over roof slab etc complete all as specified. (Note : WPC will be measured & paid for separately).

& L for plain cement concrete, (1:3:6) Type C2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

M&L cement concrete in surface channel and drain etc in 1:2:4, type B1(using 20mm graded stone aggregate) complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finishing the surface even and fair complete all as specified and directed.

M & L for brick work with old size bricks (sub class 'B' bricks) straight or curved on plan exc 6.0 m mean radius built in CM 1:4 complete all as directed and specified.

M & L Rendring 12mm thick in cement mortar 1:3 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

S & F 150mm Reinforced concrete pipes, class NP3, laid and jointed complete with coollars complete all as specified and directed..

M & L 150 mm thick PCC 1:3:6 type C-2 in concrete bed to drain pipes including packing under, and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc incl racking out joints, hacking for key and scrubbing down with water complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including removal to a distance exc 250 m but n.exc 500 m complete all as specified and as directed.

M&L for preparation of old decorated plastered/ unplastered surfaces of walls of any description by washing, rubbing down and applying one coat of cement base paint complete as specified and directed.

M&L for preparation of old decorated plastered/ unplastered surfaces of external walls of any description by washing, rubbing down and applying one coat of apex paint (weather coat) complete as specified and directed.

Ditto all as per item No 96.00 above but one coats of weather coat paint (apex) over a coat of cement primer complete all as specified and as directed.

M&L for preparation of old plastered/unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss, and efflorescent salts and trading oil and greasy spots and applying two coats of distemper oil emulsion, white or tinned (change of colour as required) complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) including all type of tiling, marble chips , terrazo finish where ever existing etc all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for water tank of old pattern including staging and removing the same exc 1.5 Km from defence land complete all as specified and directed

M&L PCC 1:2:4 type B1 (20mm graded stone aggregate) , 25 mm thick as in sub top layer of floor and finished rough to receive the floor tiles.

M & L for 20 - 25 mm thick machine cut Kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including incl Screed bed or bedding layer of Cement Mortar (1:6), 15 mm thick for laying floor finishes, necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed. Note: (size of the stone slab not less than 22"x22")

M&L Machine cut Kota stone slab flooring 20-25mm thick as in skirting, over cement mortar laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete incl 10mm thick plaster in CM 1:6 complete all as specified and directed.

Cutting holes into or through brick or concrete wall, built in cement mortar superficial area n.exc 150 Sqcm complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) exc 1.5 Sqm but not exc 4.0 Sqm each complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings.

S&F Steel work in tubular trusses 40mm nominal bore medium weight inlcluding special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St. 240 complete all as specified and directed.

S&F Gl frame work powder coated for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and size of grid 605mm x 605mm complete for false ceiling all as specified and directed by Engr-in-Charge

S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M & L for 6mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/ GI/ Aluminium framework with screw as per manufacturers instructions ® complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mps as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by E-in-Charge

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by E-in-Charge

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and change of existing colour including removal of sclaed paint and applying two coats of synthetic enamel paint complete all as specified and as directed.

M & L for Point wiring with in repair PVC insulated PVC unsheathed electric FRLS cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling PVC conduit on surface will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs excluding MS boxes for mounting switches, sockets, fan regulators etc for one light/fan point controlled by one switch complete all as specified and as directed. Make of cable: Polycab/Havell's/Finolex/Mescab and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

All as per item no 114.00 above one 5 Amps socket out let point controlled by one switch on same board with other switches complete all as specified and directed.

All as per item no 114.00 above one 5 Amps socket out let point on independent board controlled by one switch complete all as specified and directed.

All as per item No 114.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent boardcomplete all as specified and directed. Make of cable: Polycab/Havell's/Finolex and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

Supply and fixing switch piano flush button single pole one way 5 amps, 230 Volts complete all as specified and as directed.

Supply and fixing switch piano flush button single pole one way 15 amps, 230 Volts complete all as specified and as directed.

Supply and fixing socket outlet flush type 5 Amps, 5 pin, 230 Volts complete all as specified and as directed.

Supply and fixing socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 63.5mm dia three terminal, fixied complete all as specified and as directed.

Supply and fixing electronic fan regulator 450 watt 240 volt AC step type complete all as specified and as directed.

Supply and fixing Lamp holder, insulated body with back plate suitable for batten/angular fittings fixed complete all as specified and as directed.

Supply and fix LED Lamp 7/8 watt complete all as specified and directed.

Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and as directed. Make: Havell's Cat No: HEXAFT10WLED857SSYMBOPC or equivalent model of Bajaj/CG.

Supply and fixing in repair LED tube light batten box type with decorative end caps suitable single tube 1x 18/20 watt T8 lamps type complete with both end bi-pin holder and all accessories internally pre wired and fixed to wall/ceiling incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size with and including 01 No tube 18/20 watt all as specified. Make of Fitting- Havells, Cat No: REGALBATTENT8UPTO1X22WDSBSWH or equivalent model of Bajaj/Philips/Crompton. Make of tube: Havells Cat Part No. CRYSTAL1213T8DSTL20WLED865SGLASS or equivalent of Bajaj / Philips / Wipro / CG.

Supply, installation, testing and commissioning of ceiling fan 1200 mm sweep, heavy duty, single phase, AC, 230 Volts, 50Hz, ISI marked complete with 30 cm down rod, canopy, blades, etc and connecting upto ceiling rose/connector with flexible wire of size 0.75 Sqmm as per the direction of Engr-in-Charge Mak : Havells cat No ES NEO of equivalent model of Usha/ Crompton

Supply and fixing sheet metal enclosure for 4 way distribution board (DB's) double door, single pole and neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB'S/Isolators complete all as specified and as directed Make : Schneider/ Legrand/ L&T / ABB.

Supply and fixing double door SPN DBs 08 way of powder coated DB's suitable for MCB's fitted with bus bar, Neutral link, Earth bar and Din rall as per existing finishing complete all as specified and as directed Make : Schneider/ Legrand/ L&T / ABB.

Supply and fixing MCB SP 240 volts 5 to 32 Amps, 10 KA breaking capacity, 'C' type including connection complete all as specified and directed by Engr-In-Charge. Make : Schneider/ Legrand/ L&T / ABB.

Supply and fixing MCB SPN 5 to 32 amps 10 KA, C-series including connection complete all as specified and directed by Engr-In-Charge. Make : Schneider/ Legrand/ L&T / ABB.

Earthing complete with galvanised steel earth plate electrode 600mm X 600 mm X6.30mm thick burried directly in ground (earth plate not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to and including GI earth lead of Gi wire 4 mm size by means of steel bolts,nuts, check nuts and washers, PCC 1:2:4 type B-1 in pit, angle iron 25X25X3mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways abd 12mm dia MS fabricated handle, medium grade GI watering pipe 20mm bore with funnel, wire mess and light grade GI protection pipe 40mm bore upto 5m lenght for drawing in earth lead ,salt,charcol etc. including excavation and earth work in any type of soil , removal of surplus soil to a distance not exceeding 50m complete all as shown in electrical plate No. 5 of MES schedule 2009 part-I and connected complete all as specified including testing on completion.

Supply, laying & testing XLPE insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 16 Sqmm nominal cross section x 4core complete all as specifed and as directed. Makes of cable : Finolex/Polycab/ Havells/Grandlay.

Supply, laying & testing XLPE insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 10 Sqmm nominal cross section x 2 core complete all as specifed and as directed. Makes of cable : Finolex/Polycab/ Havells/Grandlay.

M & L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable and gentally hand ramming and consolidation etc. complete all as specified and directed. Note :- Thickness of sand shall be measured 18 cm thick after punning.

M & L brick cover of old size briks sub class 'B' with width equal to the length of the brick laid dry & fielt abutted with each other with gap between adjacent brick n.exc 1pp mm over UG cable for protection complete all as specified and directed

Taking down carefully copper / aluminium point wiring (light, fan, switch, socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose, sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

Supply and fixing double door TPN DBs 4 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed.

Supply and fixing MCB TPN 50-63 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed.

Supply and fixing LED security light fitting 25 watts capacity 240 volts 50 Hz IP-66 protection and impact resistance of IK-07 including all accessories such as driver, SPD etc complete with GI pipe light grade 43 mm dia bracket of size minimum length 0.80 mtrs with suitable clamp for fixing to wall complete all as specified and as directed. Make:Havell's cat No-ENDURAPEARLSL25WLED757SASYTOPCMP or equiv. of CG / Bajaj/ Philips.

S & F down rod for ceiling fan made out of 15 mm dia MS pipe with holes, slotted or threaded upto 3.0 m long all as per site requirement and directed by Engr-in-Charge.

M&L sub main wiring with 2 run of 4.00 sqmm (nominal cross-sectional area) PVC insulated (FRLS) unsheathed single core cable of working voltage 1100 volts grade with stranded copper conductor including one run of 2.50 sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed cable with stranded copper conductor as continuous earth wire connected in common earth dolly drawn in PVC rigid non- metallic conduit complete all as specified and as directed. (NOTE : (i) Two run of submain wiring cable alongwith one run of earth wire shall be measured as one length). Make of cable:-Polycab/Havell's/ Finolex

Supply and fixing GI tubing, light grade, 40 mm bore with all fitting laid in trenches / pole / wall for protection of cables complete all as specified and directed.

Vijay Bakshi and Son

M/S Priya Trading Agency

HARINANDAN RAI SONS

M/s Naresh Chand Agrawal

M/S MODERN CONSTRUCTION

jaglalchoudharyandsons

M/S SAROJ KUMAR SINGH