Provn of 02x Guard Room With Allied Infra To Bldg No

Amount

Surface excavation n.exc 30 cm deep and and avg 15 cm deep and getting out any type of soil complete all as specified.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. ®

M & L for sand filling under floors or in foundation including watering and consolidation complete all as specified.

M & L for hard core using broken stone of gauge n.exc 63mm deposited,spreading and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified.

M&L for PCC 1:4:8 type D-2 (using 40mm graded aggregates) as in bed concrete for foundation filling & mass concrete complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified.

M & L for reinforced cement concreteM-25 Design mix (using 20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed.

M & L for reinforced cement concrete M-25 Design Mix ( using 20mm graded aggregate) in Columns, pillars, piers, etc complete all as specified.

M & L for reinforced cement concrete M-25 Design Mix (using 20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M & L for reinforced cement concrete M-25 Design Mix (using 20mm graded aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span and complete all as specified.

M & L for reinforced cement concrete M-25 Design Mix (using 20mm graded aggregate) in Chajjas complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter and complete all as specified.

M & L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions and complete all as specified.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200mm thick (Horizontal or sloping) and complete all as specified.

M & L for formwork to chajjas and similar items, flat surface incl edges complete all as specified.

M & L for formwork to sides and soffits of floor or roof beam, flat surface etc incl supports, overhangs etc complete all as specified.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the mild steel wire (annealed) not less than 0.9mm dia or securing with clips and complete all as specified.

ditto all as per item No 17 here- in -beore but 6 to 8 mm dia and including in stirrups, spacers and binders and complete all as specified.

M&L for brickwork with old size sub class 'B' brick straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified.

M&L for brickwork with old size sub class `B' bricks, straight or curved on plan to any radius in half brick thk wall, built in cement mortar1:4 complete all as specified.

M&L for rendering 15 mm thick cement plaster in CM 1:6 on brick Work or concrete surfaces including finished even and smooth without using extra cement all as specified and directed.

M&L, Rendering 15mm thick in CM 1:4 on of brick work or concrete surface finish ever and smooth (w/o using extra cement) incl WPC as per user manual complete all as specified and directed. (WPC will be measured and paid separately).

Supply only liquid WPC

M&L, Rendering 10mm thick in CM 1:3 over concrete surface as on ceiling, chhajja, shelves etc to match with existing surfaces finish even and smooth w/o using extra cement complete all as specified and directed. .

M & L for preparation of new plastered surface and applying two coats of oil bound distemper on wall over one coat of primer etc complete all as directed.

M&L for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance complete all as specified and directed.

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling,chhajja, shelves etc surfaces and complete all as directed.

M & L for 50 mm thick PCC 1:3:6 type C-1 (using 20 mm agg. ) as in plinth protection / path/ any paved area complete all as specified and directed.

M&L for providing 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring complete all as directed.

M&L for18-22 thick kota stone slab flooring (Machine cut) of any size laid over and including 20mm thick bedding layer in CM 1:6 over neat cement slurry @3 kg/sqm over sub base, jointed and pointed in grey cement mixed with pigment to match the shade of slab including rubbingg and polishing to achieve mirror finish comlete all as specified.

M&L for non-skid ceramic colour/printed tiles 7to 8mm thick (Square/rectangular) area of each tiles exe. 0.11 sqm but n.exe 0.18 sqm, in dados,skirting etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick cement plaster in CM 1:4 as bedding layer all as specified and directed.

M&L for kot stone slab 18-22 thick in riser, steps, skirting, dado and pillar laid over 10mm thick 1:3 cement mortar jointed and pointed in grey cement mixed with pigment to match the shade of slab including rubbing and polishing to achieve mirror finish comlete all as specified.

M&L for Pressed steel frames of size 125mmx60mm for doors with one or more rebates fabricated out of 1.25mm thick mild steel sheets with and including necessary fixing lugs, hinges (100mm medium weight-03 Nos on each rebate), lock strike plate with and including filling of hollow portion in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and making good the existing surface in cement mortar 1:6, complete all as specified.

S&F 35mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F for 2nd class Hard wood glazed and skelton door shutters 35mm thick, open rebated and prepared to received glass/gauge etc (without sash bars) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in SSR part-I clause 8.23(b) and fitted to chowkahts etc complete all as specified.

S&F for Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel with particle board core design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face supplying & fixing inframe at site as per specification & drawing and as per manufactures instructions complete all as specifed

S & F for Solid PVC moulded Door Frame of size 50mm x 47mm made out of 5mm wood grain printed/ colour PVC sheet reinforced with M.S. Square tube, and opening as per manufacturer's instruction complete all as specified and directed.

S&F steel window made up of box steel section of 16 gauge MS Sheet in outer frame, shutter frame and centre frame, with fixed type partly glazed and partly gauzed with outer side glazed shutter and inner side wire mesh shutter fixed with suitable steel handle dovetailed or welded with each shutters pannels complete with necessary cleat and stopper complete all as specified and directed. (Drg No : CEUZ/TD/1302/2009)

S&F steel ventilator made up of box steel section of 16 gauge MS Sheet fixed type partly galzed and partly gauged inner frame and centre frame, including outer side glazed shutter and inner side wire mesh shutter fixed with MS clip consisting with dovetailed or welded with each pannels complete with necessary cleat and stopper all as specified and directed.(MS gaurd bar/griil work will be measured and paid separetly) (Drg No : CEUZ/TD/1302/2009)

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S& F for 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 sqm quality or description from steel frame and all specified.

M & L for two coat of synthetic enamel paint over a coat of red oxide on steel surface including preparation of new steel surface width or girth exc 10cm all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces of any description over 10cm width or girth including preparation of new surfaces complete all as specified and directed.

S&F for MS butt hinges, medium weight, cold rolled mild steel 100mm long (ISI Marked) with welded or complete all as specified and directed.

S&F for aluminum anodized barrel tower bolts of extruded section 150mm long (ISI Marked) complete all as specified and directed.

S&F for aluminum handles cast type anodized 150mm long (ISI Marked) complete all as specified and directed.

S&F for 250mm long aluminium alloy, anodised, sliding door bolt of 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed.

S&F in repair, 300 mm ordinay rat tail rod pattern springs incl roller and rabber plate fixed to chowkhats in repairs incl necessary welding if reqd. complete all as specified and directed.

S&F GI tubing 15mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

M&L for cutting chases in brick wall pinning in making good to facings where required and pointing in CM 1:3 to ends or edges of lintels, etc and cutting chases for concealed water tubing etc and making good cutting n.exc 10cm girth complete all as specified and directed.

S&F GI tubing 20 mm bore medium grade medium grde with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F for 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. .

S & F for vitreous China white wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap complete, front or back inlet, fixing bolts, PVC seat cover including 32 mm dia PVC flush pipe and making all necessary connections complete as specified

S&F for vitreous china squatting pan of pattern “long pan”, size 580 mm white with ‘P’ or ‘S’ trap, front or back inlet and foot rest, any pattern including provision of lime concrete bedding fixed complete all as specified and directed.

Vitreous China, wash hand basin, counter top, white, of size 530mmx445mmx195mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts,32mm dia, chain and plug, porcelain stopper with and including PVC collapsible waste pipe of suitable length complete all as specified. Make: Jaquar Cat Part No. ECS-WHT-601 or equivalent in Make .

S & F for vitreous china urinals, half stall type (635x450mm) , complete incl providing and fixing , bedding urinal against wall in cement mortar 1:2 , pointing around urinal back in cement , grating and union for discharge pipe, CP urinal spreader and fitting with CP waste coupling all as specified and directed.

S&F for PVC valveless,syphonic action type, flushing cistern of 10 ltrs, low level of approved colour, with inlet, ball valve, float and handle including brackets and complete assessories complete all as specified and directed.

S&F for PVC connection 15 mm dia with PTMT nuts of length 600 mm complete all as specified and directed.

S&F for rotational moulded polyetheylene water storage tanks (cylingrical verticlal with closed top) of 1000 ltr capacity, hoisted and fixed in any position incl 20 mm dia float valve with aluminium fitting and any GI fitting complete all as specified and directed.

S&F for CP Wash hand basin mixer cast copper alloy, chromium plated, screwed for 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm and fixed,complete all as specified.

S&F 15mm dia bib tap long body cast copper alloy chromium plated with crutch (or) butterfly handles, screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S & F for 15 mm Stop valves/Angle cock cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed omplete all as specified.

S & F for 15 mm Stop valves concealed type cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed omplete all as specified.

S&F for Towel Rail CP 20mm dia and 60cm long D type between flanges complete all as specified and directed.

S& F for toilet paper holder of CP with cover complete all as specified and directed.

S&F for grating round 125mm size of CP complete all as specified and directed.

M&L for Granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl moulding ,rounding of edgeing complete all as spd and directed.

S&F for 110mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete all as specified and directed.

All as per ser item No 69 here-in -before but laid in trench or in floor

S&F for 110mm bore PVC Gully Trap setting / jointed with solvent cement complete all as specified and directed. .

S&F for 110mm bore PVC bends/junction / Tee any radius complete all as specified and directed. .

M&L for preparing surfaces by brushing with wire brushes for removing caked mud etc. Sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt & applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) land on primed surface by forced application, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed.

M&L, PCC 1:3:6 type C as in roof Pading (using 20 mm graded aggregate ) complete all as specified and directed.

M&L for mild steel framed work as in grill, guard bars , framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and directed.

M&L for expanded metal, cut to length, bent to shape required and tying with and incl annealed mild steel wire not less than 0.9mm dia or fixing with galvanized steel staples supplied and fixed complete to wood or steel members, weight exc 4 Kg per Sqm, complete all as specifed & directed.

M&L for factory made pre-cast cement concrete block type B1, 1:2:4 as in kerb stone made to shape as directed, exc. 10 cm in width and setting in mortar 1:4, complete all as specified and as directed.

M&L for broken stone hard core gauge n.exc 63mm deposited, spred and levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces complete all as directed and specified.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60mm thickness, with grey cement, pigment incl 25mm thick sand filling complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (40 mm graded aggregate) in foundation filling and mass concrete for bottom of manhole/ drain etc complete all as specified & as directed.

M&L type B1 1:2:4 (20mm graded aggregate) providing RCC precast cement concrete as in cover slab for man hole and similar article with plain face and set in cement mortar 1:4 complete all as specified & as directed.

Supply and laying in trenches, jointing and testing salt glazed stoneware pipe grade 'A' drainpipe 150mm bore conforming to IS at any depth over PCC 1:3:6 type C-2 (using 20mm graded crushed stone aggregates) for bed of sewage lines of 150mm dia incl packing under haunching against the sides of pipe after they are laid and tested complete (all as per specified in SSR part-I clause 18.68.2) complete all as specified & directed. (Excavation and earth work shall be measured and paid for separately under appropriate items of Sch. 'A'.)

M&L for Cutting into existing man holes for connecting new drains making good to pipes and rendering cutting out existing benching for and forming branch channel (1/2 round or ¾ in section) in cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) surface smooth finished and reforming benching as required for internal dia of pipe 150mm all as specified and directed .

M&L for Construction of Septic tank for 25 Users (Brick Construction), complete all as specified and as shown on drawings No. CEUZ/TD/1202/03 sheet 1/2 & 2/2 dated 14/10/2014 and 11/05/2007 respectively complete all as specified & as directed.

M&L for Construction of soakage well 1.80 m dia and 4.5m deep (Internal dimensions) (Brick construction), complete all as specified and as shown on drawing No . CEUZ/TD/1202/03 sheet 1/2 & 2/2 dated 14/10/2014 and 11/05/2007 respectively complete all as specified & as directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded aggregate in surface channels and drains complete all as specified & as directed.

BLANK

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in coping/benching and all other similar works including necessary formwork complete all as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc complete all as directed.

M&L for 15mm thick plastering on roof surface in CM 1:4 surfce finished even and smooth without using extra cement, comp[lete all as specified and directed.

M&L for Chicken wire mesh of size 12.5mm and wire dia 0.51 mm (24SWG) hexagonal construction, stretched firmly for roof treatment, complete all as specified and directed.

M & L for Glazed ceramic jointless light/cooured group fo size 0.13sqm but n.exe 0.18 sqm area of each tiles as in vertical surfaces such as skirting etc, set and jointed in neat cement slurry and pointed with white cement and pigment to match, including 10mm thick rendering in cement motar 1:4 complete all as specified and directed.

M & L for cheqered tiles of size 300 x 300 x 25 mm thick (colour and glazed approved by EIC) with grey cement and pigments laid over 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismanting complete all as specified and directed.

S & F for Steel work in tubuler trusses including special washer etc, complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St-240 complete all as specified and directed.

S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified.

M & L two coat of synthetic enamal paint over a coart of red oxide on steel surface incl preparation of steel surface width or girth exc 10 cm all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out returning, fitting in & ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exe 50m and making good surface complete all as specified and directed.

M & L cement concrete (1:3:6) type C1 (20mm graded stone Agg) as in embedding of angle iron post complete all as specified and directed.

M & L for concealed point wiring on wall and ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 20 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash all as specified and directed by Engineer-in-Charge for the following:-

(a) One light /Fan/Bell point controlled by one switch 6/5 Amp one way single pole.

(b) One 3 pin 6/5 Amp socket outlet controlled by one switch independent board.

(c ) All as per item No 2 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

Supply & Fixing SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 8 way, confirming to IS 13032 & 8623 complete all as specified and directed.

Supply & Fixing MCB SPN, 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.

Supply & Fixing MCB SP, 06 to 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.

S&F ceiling rose, surface bakelite, 65mm x 50mm, two to three terminals complete all as specified and as directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

S&F switch piano flush type (ISI marked), single pole, one way 6 Amp, 240 Volts complete all as specified and as directed.

S&F socket outlet 3 pin, 6 Amp piano flush type including complete all as specified and as directed.

S&F socket outlet, 2 in 1, 3/5 pin 6 / 16 Amp, piano flush type complete all as specified and as directed

S&F switch piano flush type (ISI marked), single pole, one way 16/15 Amps, 240 Volts including complete all as specified and as directed.

S&F LED lamp 230 volt AC 12 watt complete all as specified and directed

S&F Wall mounted LED batten 18/20 Watt with 01 No LED tube rod, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver complete all as specified and directed.

Supply & Fixing medium step type fan regulator 240 Volt AC, socket size, medium step" ISI marked complete all as specified and directed. Make -Havells/Cona/Anchor/Legrand

Supply & fix fans ceiling complete 230 V,1200 mm sweep.energy efficient alngwith connecting wire complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver and grid wire mesh and making hole 300 mm dia for fan exhaust and making good complete all as specified.

S&F LED building security light 35 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade suitable size dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener all as specified and directed.

M&L for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron wire 4 mm dia (8 SWG) as earthing lead protected by GI pipe medium grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required. Note : Earthing lead/G.I.Earth wire upto 7.5 metre length shall be deemed to be included in quoted unit rate beyond 7.5 metre, the same shall be measured and paid separately).

Material and labour for fixing or passing through pipe, laid in trenches or fixed to pole/wal or fixed to LT panel board, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed 16 Sqmm 2 core with required aluminium cable lugs all as specified and directed. Make of Cable : Havells, Polycab, Nicco, Gloster,Finolex

Supply and laying in trenches/Floor or fixed to Pole/Wall GI pipe light grade with fitting of size 40 mm bore for protection of cable including dismantling existing pipe complete all as specified and directed by the Engineer-in-Charge.

M&L for cutting of PCC/Hard standing/WBM road not exceeding 20 cm in width not exceeding 30 cm in depth for passing of LT cable and making good of disturbed surface to match with the existing surfaces by using old and new material i.e bitumen/PCC (1:3:6) type C-1 complete all as specified and directed .

M & L for dry Sand cushioning in trenches for protection of cable including watering and consolidation all as specified and directed. Note: Punned thickness shall be considerd for measurment purpose

M & L for well burnt brick sub class B old size laying in trenches perpendicular to axis of the cable complete all as specified and directed.

Suppy and fix electric water heater, storge type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete all as specified and directed

Suppy, alying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 110 Volts grade with standed aluminium conductor of size 10.0 sqmm 2 core.

Supply and laying in trenches GI pipe medium grade with fitting of size 25 mm bore for protection of cable complete all as specified and as directed.

S.K CONSTRUCTION

DAVINDER SINGH

R K BUILDERS

M/S SANJAY STEEL WORKS

SHIVAE CONSTRUCTION