Construction of New office building for Irrigation Division Hathras.

Amount

Excavation in foundation in ordinary soil (loam clay or sand) eluding lift up to 1.5 M and lead up to 30 M and including filling, watering and raming of ecavated earth into the trenches in to the space between the building and the side of the bundation trenches or into the plinth and removal and disposal of the surplus earth as directed by the Engineer-in-Chief up to a istance of 30 M from the foundation trenches.

Providing and laying (M 15)C.C 1:2:4 with coarse sand and aggregate of size 10 to 20 mm including mechanical mixing and all cost of material, labour and T&P etc.required for proper completion of work .

Providing and laying (M 25)R.C.C 1:1:2 with coarse sand and aggregate of size 10 to 20 mm including mechanical mixing and all cost of material, labour and T&P etc.required for proper completion of work upto plinth level. but excluding cost of steel reinforcement.

Providing and laying (M 25)R.C.C 1:1:2 with coarse sand and aggregate of size 10 to 20 mm including mechanical mixing and all cost of material, labour and T&P etc.required for proper completion of work Above plinth level. but excluding cost of steel reinforcement.

Centering & Shuttering for R.C.C. Work in foundation, columns, beams. Lintels, sunshades roof slabs with MS later/Plywood panels of required shapes & sizes including all material & labour required to complete the work upto 3m height

Centering & Shuttering for R.C.C. Work in foundation, columns, beams. Lintels, sunshades roof slabs with MS later/Plywood panels of required shapes & sizes including all material & labour required to complete the work above above 3m.

Mlild steel ( Tor/TMT) in reainforced concrete work wrought to required shape as necessary including bending as per requirement and direction of E/I for proper completion of the work and including suppy of steel, its wastage, labour and T&P etc. complete. (Bend, hooks and authorised overlapping in inforcement shall be measured.

Eearth filling under floors upto PL including cost of the earth, iarth to be obtained from outside including its cartage and ramming watering, dressing in 20Cm. Thick layers and dressing of area etc. complete including cost of earth with all lead and lift etc. complete.

1 st Class brick work (M-150) in 1:6 cement and Coarse sand of 2.25 F.M. mortar in foundation and Plinth I/C supply of all material, labour and T&P etc. required for proper complection of work (Upto PL)

1st Class brick work (M-150) in 1:4cement and Coarse sand of 2.25 F.M. mortar in foundation and Plinth I/C supply of all material, labour and T&P etc. required for proper complection of work (above PL) for 230mm wall.

1st Class brick work (M-150) in 1:4 cement and Coarse sand of 2.25 F.M. mortar in foundation and Plinth I/C supply of all material, labour and T&P etc. required for proper complection of work (above PL) for 115mm wall.

40 mm thick damp proof course with cement concrete consisting of 1 part cement 1.5 parts approved coarse sand and 3 parts approved 20mm down graded stone grit and including water proofing material etc. complete.

12mm thick plaster with cement mortar in proportion of 1:6 cement and sand 1.00 fineness modulous over brick work minimum thickness not to be less than 1 cm including supply of 1 material labour and T&P etc. required for proper completion of work for all floors.

P/F 125mm x 65 mm Indian Salwood frame as per approved design/drawing including all hold fast and grouting in 1:2:4 CC Complete.

P/F MS section window & Ventilators made upto F4 &Z Sections as per drawing joints mitred & welded with 13x3 mm ugs 10cm long embedded in CC blocks 15x10x10cm 1:2:4 CC or dash fastners with nuts & Bolts as required including fixing of necessary fittings, gril as per design also including fixing of 4mm thick black glass pants with putty & clips, SS wire mesh in frame of MS flat and applying a painting coat of approved steel primer.

Providing and fixing stainless steel ( Grade 304) GATE made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the waist slab with suitable arrangement as per approval of Engineer-incharge,

P/F 1st marked flush door shutters 30mm thick (IS:2202 decorative type core of block board construction with frame 1st class hard wood and well matched teak 3 ply veneering with vertical grains and face vernors on both faces of shutters I/C frosted glass, French Spirit polish, with exposed door closer 0 Godrej/Dorma make with all other hardwares suxh as SS hinges, SS. morties locks door silencer, stoppers, cleats, of the assosries etc. as per detailed approved drawing etc. complet I/C supply of all material, labour and T&P etc. required for proper for proper completion of the work as per direction of E/I.

P/F 1st marked flush door shutters 30mm thick (IS:2202 Non decorative type core of block board construction with frame 1st class hard wood and well as S.S. hinges, S.S. mortise locks door silencer stopeers, cleats, other accessories etc. as per detailed approved drawing etc. complete I/C supply of all materials, labour and T&P etc. required for froper completion of the work as per direction fo E/I.

S/F of 4cm. Thick C.P teak wood Part panelled & Part glazed door & window shutters I/c supply and fixing of wooden cheats and stops and fittings including painting two coats of black Japan on all iron fittings if necessary including fixing the panes (5mm thick ).

S/F of 4cm. Thick C.P teak wood fully glazed window shutters I/c supply and fixing of wooden cheats and stops and fittings including painting two coats of black Japan on all iron fittings if necessary including fixing the panes (5mm thick ).

Supply & fixing S.S Mosquito proof heavy quality iron wire gauge or expended metal heavy qualityiron wire gauge or expended metal heavy quality over windows and including suplly of C,P teak wood batten 8 cm x 1 cm flat iron 25mm X 4mm and including supply of necessary screw all materials, labour, tolls & plant etc. required for proper completion of work.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge

Painting with approved quality and shade of paint-on-new work or new wood work with one coat of ready mixed priming paint and two coat of approved superior quality read mixed paint luxol or equivalent brand confirm to the ISI No. 103(950) including supply of all material, labour & T&P etc. required for proper completion of the work.

Finishing Walls with POP approved Brand and manufacture and of required shade and undacorated wall surface to give even shade over including curing, cost of all materials, labours, T&P etc. required for completion of the work

Applying Birla putty on Exterior & interior surface over one coat of water based cement primer of ICI brand for smoothering and levelling of the surface as per requirement and direction of engineer in charge including cost of all material, labour T&P etc.

Finishing walls (Two coat ) with Exterior & interior emulsion paint (Apex) of approved brand and manufacture and of required shade on undacrated wall surface to give even shade@ 1.25 ltr/10sqm including one coat of primer applied @ 0.75 ltr/sqm, including cost of all materials, labour T&P etc. complete required foe proper completion of work.

P/F Ist quality ceramic glazed wall tiles confirming to IS:15622 of approved wake, in all colour shades except burgundy. Bottol greeen, black of any size on walls over 12mm thick bed of cement mortar 1:3 and joining with grey cement slurry @ 3.3 kg/sqm including painting in white cement including supply of all material, labour and T&P etc. required for proper completion of work to be provided in toilets upto 2.1 M height.

P/F Rectied Glazed ceramic floor tiles of size 300x300mm of 1st quality confirming to IS:15622 in colour white Ivory, Grey fume red brown laid on 20mm thick cement mortar 1:4 including grouting the joints with white cement and matching pigments etc. Complete including supply of all completion of work of floor of toilets.

P/F 18mm thick Agaria white stone including its Mirror Polishing and fixing with 20mm thick base of cement mortar 1:4 (Cement sand) and jointing with white cement slurry mixed with pigment to match the shade if required including rubbing and polishing as per direction of E/I and finally finished with French mansion polish or equivalent etc. complete in staircase.

P/F vitrified tiles of size 600x600mm of (IS:15622) of approved shade,colour and pattern as approved by E/I laid with 1:4cement & coarse sand mortarJointing with Cement slurry @ 3.3 kg/sqm with approvedquality of adhesive finished with white cement & pigment to match the tile shade including cost of all material,labour & T&P etc required for proper completion of work. with lean Concrete.

Providing and fixing Hand rails and Balustrade modular system passive SS-304 grade decorative railing system comprising of hand rail 50mm and 1.5 mm thick and 3 no. horizontal steel pipe of 19mm dia and 1.5mm thick of equal spacing with balustrade of SS pipe of 38 mm and 1.5mm thick @ 1200mm C/C of passivated SS 304 grade and fix duly on the floor with specially design rivet expansion bolt and finish the surface food and covering with steel shoe, with all visible stainless steel metal of 304 grade in satin finish height of railing is 900mm as per detailed specification as per approval of Engineer-incharge.

Providing and injecting chemical emulsion on bottom surface and sides and the back fill in immediate contact with the foundation structure and vertical surface of the sub structure of each side @ 7.5 litres/Sqm specified with chlorpyrephos E.C 20% with 1% concentration for preconstruction anti termit treatment and creating a chemical barrier under and around foundation walls , column, pits back fill earth junction of wall and floors external perimeter of building surrounding pipe under apron etc.

P/F 10mm thick glazed GRANITE tiles of size or more of approved clour and pattern in floor, skirting or dad laid with 1:3 cement and coarse sand mortar and joints finished with white cement with pigment to match the shade of tiles

Providing and laying water proofing treatment to vertical & orizontal surface of sunken slabs as per following. 1st course of cement slurry @ 4-4 kg./sqm mixed with water proofing compound as per IS 2645 rounding off the junction Iind course 0 mm cement plaster 1:3 (Cement : coarse sand) plaster founding off the junction, IIIrd course applying bot bitumen @ 7 kg. & IV th course pasting 4.00 micron polythene sheet over bitumen with 100mm overlap at junctions including cost of all material labour, T&P required for proper completion of work.

Providing 1 m wide apron PCC 1:2:4 ( 1cement : 2 Coarse sand:4 grit of nominal size of 20mm) finished with a coat of nea cement laid in slope of 50mm all round the building, on subbase of 100 mm thick ballast complete.

P/L Brick coba 12 mm thick laid with M-150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20mm thick base of cement and coarse sand mixed with water proofing compound spreding cement slurry mixed with water acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false squre 30cmX30cm and side wall parapet shall be mono tythic plaster upto 30cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary coba with top finished plaster mixed with acetic compound @2% by weight & including supply of material , labour , T& P etc complete for proper completion of work.

Providing and fixing at Bamboo Mat board conforming to IS:13958-1994 for partition to frame by bucking or studding with screws etc. complete (Frames, backing or studding to be paid separately. (12mm thickness)

Wiring point for light with 1.5 sq.mm FRLSH PVC insulated multistrand single core Copper Conductor cable in PVC conduit pipe partly concealed in wall & partly laid in slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable earth continuity wire, piano type switches & ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash.

Wiring point for two ways light with 1.5 sq.mm FRLSH PVC insulated multistrand single core Copper Conductor cable in PVC conduit pipe partly concealed in wall & partly laid in slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit continuity wire and two number two way piano type switches & ceiling rose / angle / batten holder on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash.

Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.5 sq.mm FRLSH PVC insulated multistrand single core Copper Conductor cable in PVC conduit pipe partly concealed in wall & partly laid in slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit continuity wire, piano type switch & ceiling rose on 3 mm thick phenolic paminated backelite sheet etc complete in all respects as directed, including matching color wash.

Wiring point for plug with 1.5 sq.mm FRLSH PVC insulated multistrand single core Copper Conductor cable in PVC conduit pipe partly concealed in wall & partly laid in slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit continuity wire and piano type switches & socket etc., complete in all respects as directed, including matching color wash.

Wiring points for Call bell with 1.5 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire and piano type bell push or 2pin socket etc.complete in all respects.as directed including matching colour wash.

Wiring points for Call bell with 1.5 sqmm.FRLSH PVC insulated multistrand single core copper condutor cable in PVC conduit pipe partly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire and piano type bell push or 2pin socket etc.complete in all respects.as directed including matching colour wash.

Addition for light / fan points with modular type switch in place of piono type switch.

Addition for two way points with modular type switch in place of piono type switch.

Addition for HPSV/Exhaust Fan points with modular type switch in place of piono type switch.

Addition for plug points with modular type switch in place of piono type switch.

Addition for call bell points with modular type switch in place of piono type switch.

Supply fixing and concealing of 20mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin/ adhesive to make the complete piping rigid,plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work.

Supply & wiring of submains with two number 2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit with 1 Number 1.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect.

Supply & wiring of submains with two number 4 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit with 1 Number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduit complete in all respect.

Supply and wiring of submain 2 number 6 sqmm . FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in 20mm dia heavy duty (2mm thick ) PVC conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with one number 4.0 Sqmm FRLSH PVC Multistand copper earth contunity wire including colour wash etc. complete in all respects.

Supply and wiring of submain with 4 number 10 sqmm . FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in 32 mm dia heavy duty (2mm thick ) PVC conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting with two number 10 SWG copper earth contunity wire including colour wash etc. complete in all respects.

Supply & fixing of single wall bracket on matching M.D.F.E.G. board base etc. complete in all required. (Cat. AAA)

Supply & fixing of Recess/Surface/Pendent mounting round 6 to 8 Watt LED down lighter having powder coated die cast Aluminium housing with heat sink, diffuser/reflecter, and driver set complete in all respect. (Cat. AAA)

Supply and Fixing of LED Tube Light with batten suitable for up to 1X22 watt LED tube light complete including tube etc. on surface complete in all respect. (1 X 22 W - CAT-AAA )

Supply and Fixing of LED Tube Light with batten suitable for up to 2X22 watt LED tube light complete including tube etc. on surface complete in all respect. (2 X 22 W - CAT-AAA )

Supply & fixing of Call Bell Of Approved Make on matching polished MDFEG board brass including connection etc. as required.

Supply & fixing of buzzer on polished MDFEG/Teak ply board including making connections etc. complete in all respect.

Supply and burying of 600mm x 600 mmx6mm G.I. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm G.I.pipe and funnel for watering and two earthing leads of No.8to10SWG G.I.wire in 15mm diaG.I. pipe upto switch board (from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm. square C.I. frame with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.

Supply and burying of 40mm dia x 4.5 metres long G.I. pipe, vertically for earthing having 12mm dia. holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No.6 to 8SWG G.I.wire in G.I. pipe upto appron (and from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) upto switch board, 30cm. square C.I.box with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects.

Supplying and fixing of one number 8 SWG G.I. wire in 15mm dia G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T & P other material required for proper completion of the work as directed at site.

Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose as required complete in all respects.

Supply & fixing of two number 8 SWG G.I. wire for earthing purpose as required complete in all respects.

Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve (5 - 32 amps.Cat. A)

Supply and fixing of 40/63 Amp MCB(10KA)C Curve (63 Amp. 4 Pole MCB C Curve-Cat. A)

Construction of recess distribution board of all sizes including cutting of brick work providing lintel of suitable size & thickness plastering etc. with supply of all materials, labours, T & P etc. required for proper completion of work. 600x480x200 mm.) size

Supply and fixing of factory fabricated M.S. box in existing sunk with Godrej type almirah cover with handle etc. fabricated from 18 SWG M.S. sheet duly painted with red oxide primer followed by two coats of synthetic enamel paint complete with necessary conduit entry and DP/TPN; fixing arrangement and provision for compartment for loose wires, openable housing on the top and hold fast etc. including supply of all material, labour and T & P etc. required for proper completion of the work. (600x480x200 mm. size)

Supply and fixing of surface/ flush mounting 6 way TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer Incharge. (CAT A)

Supply & fixing of Crimping, solder, less, copper ton electroplated lugs of Dowel/ismail make suitable for 1.5 sqmm to 6sqmm cables, including tapping with insulating tape, etc. complete in all respects.

Supply and fixing of single pole MCB blanking plate (CAT B)

Supply and fixing of power plug with 20A/250 V flush type modular switch and 5 Pin 20 A/250 Volt flush type universal modular socket switch on concealed M.S. box including supply of all material, labour T & P etc required for proper completion of work.

Erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. down rod 19mm dia duly painted, complete in all respects.

Erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects.

Supply & fixing of 16 gauge M.S.drum duly painted including making hole in the wall for exhaust fan and finishing properly etc. complete as required.

S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16 SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work.

Supply fixing of electronic fan regulator (Modular) 120-280 V. ISI marked, on the existing switch board including making connetion, required material, labour T/P etc for proper completion of work to the satisfaction of Engineer in charge of work.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. (25 sqmm 3.5 core)

Supply and fixing of danger board fabricated from 10 gauge M.S. sheet as per I.E.rules.

Supply and laying of 1800mm x 900mm x 12mm thick chequered rubber matting of tested quality.

Supply and fixing 100 AMP four pole Moulded case type on load change over switch with enclosure(also suitable for panel mounting with extra cost of bus bar) including the cost of labour, T & P , painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge.-

Wiring point for H.P.M.V./ Sodium Vapour lamp with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in in PVC conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit.

Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect. (CAT-AAA )

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. (110mm diameter )

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. (110mm)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (110mm)

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints for vertical pipes and solvent cement joints for horizontal pipes, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors), reducers, WC connectors, couplers, cowels, clamps, hangers, rubber rings, clean outs etc. fixing at wall / ceiling / floor level supported by clamp & hangers etc. inside duct / suspended from floor under false ceiling for proper completion of the work. The rubber ring shall confirm to IS:5382. (110mm dia).

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints for vertical pipes and solvent cement joints for horizontal pipes, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors), reducers, WC connectors, couplers, cowels, clamps, hangers, rubber rings, clean outs etc. fixing at wall / ceiling / floor level supported by clamp & hangers etc. inside duct / suspended from floor under false ceiling for proper completion of the work. The rubber ring shall confirm to IS:5382. (75 mm dia).

Providing & fixing UPVC Floor trap of self cleansing design with CP Jali complete in all respects. (Make : Supreme / Finolex / Prince) (110x110 mm P-Type)

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince) Door Tee (110x110x110 mm)

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince) Door Tee (75x75x75 mm)

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince)Bend -110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince)Bend -75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince)Terminal guard. (110 mm)

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion.. (Make : Supreme / Finolex / Prince)Terminal guard. (75 mm)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(internal work) Exposed on wall 20mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(internal work) Exposed on wall 25mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(internal work) Exposed on wall 32mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 15mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 20mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 25mm dia nominal outer dia pipes

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. (15mm nominal bore)

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. (20mm nominal bore)

Providing & fixing CP brass bib cock of approved quality conforming to IS 8931. (15mm nominal bore)

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931. (15mm nominal bore)

Providing and fixing gun metal gate valve with wheel of approved quality. (20mm dia nominal bore)

Providing and fixing gun metal gate valve with wheel of approved quality. (25mm dia nominal bore)

Providing and fixing gun metal gate valve with wheel of approved quality. (32mm dia nominal bore)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. (15mm dia nominal bore)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. (20mm dia nominal bore)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. (25mm dia nominal bore)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular Tank

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. (Pipes 80mm to 300mm diameter.)

Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. (150mm diameter S.W. Pipe)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :10 graded stone aggregate 40 mm nominal size) all-round S.W. pipesincluding bed concrete as per standard design : (150mm diameter S.W. Pipe)

Providing and fixing square mouth S.W. Gully trap grade 'A' complete with C.I. grating brick masonry chamber with F.P.S. bricks of class designation 75 and water tight C.I. cover with frame of 300 x 300mm. size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design. With Sewer bricks conforming to IS : 4885 (150 x 100 mm). size P type

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With FPS bricks of class designation 75 For Sewer Line

Extra for depth of man hole size 90x80 cm

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. for European type W.C. pan with white plastic seat and lid.Make- Cera,Hindware.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap.

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Felxible pipe (40mm dia)

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge. 15mm nominal bore.

Providing and fixing CP Brass 32 mm size Bottal Trap of approved quality & make and as per thedirection of Enginer-in-charge.

Providing and fixing CP Brass Single lever lelephonic wall mixture of quality & make and as per thedirection of Enginer-in-charge. 15mm dia nominal dia.

Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Fauct of approved quality conforming to IS:8931. 15 mm nominal bore-ESSCO SQT 526AKN

Providing & fixing 60x2cm. C.P. brass towelrail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw. ESSCO AEC-1181

Supplying & Fixing of CP soap tray fixed to the wall with PVC rubber plug with CP brass screws-

Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 1.5m depth

Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 1.5m to 3.0m depth

Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 3.0m to 4.5m depth

Reinforced cement concrete work inbeams, suspended floors, roofs having slope up to 15º landings, balconies, shelves, chajjas, intels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design: With 20x20mm square bar.

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. (Drilling of 300mm dia bore hole manually.)

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. (150 mm nominal size dia)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.

P/L fine sand for bed levelling for tiles

LAYING OF INTERLOCKING TILES OF THICKNESS 60-100MM INCLUDING LEVELLING & DRESSING OF SURFACE TO REQUIRED LEVEL & SLOPE.

Supply & fixing of fire extinguisher, ABC Type 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply & fixing of CO2 type fire extinguisher, 6.5 kg. capacity(ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Earth work in excavation over areas including disposal of excavated earth, lead upto 50m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 1.5m depth

Earth work in excavation over areas including disposal of excavated earth, lead upto 50m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 1.5m to 3.0m. Depth.

Reinforced cement concrete work in slab with 1:1.5:3 (1 cement : 1.5 course sand : 3 graded stone aggregate 20mm normal size).

15mm cement plaster on rough side of mix 1:4 (1 cement : 4 course sand)

Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars.

Providing and fixing C.I. tee at the inlet and outlet of septic tank.

Providing & fixing 75mm dia vent pipes.

Providing & fixing of 75mm dia cast iron terminal guard.

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. (M.D. -10- Circular shape 500mm internal diameter)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. L.D. -2.5- Circular shape 450mm internal diameter

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design. With F.P.S. bricks

Earth work in excavation over areas including disposal of excavated earth, lead upto 50m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 1.5m depth

10 KW off-Grid Roof top solar Power Plant including inverter, single phase with internal MPPT efficiency-99.9%, 120V, Input Voltage range-108-144V , Output Voltage range -230+2%, Battery (Exide)(12V,150AH)-20nos . Fitted at Fabricated M.S Dipped galvanized fixed structure with columns,beam and purlines, Angles and Z-section and Nuts & Bolts Designed to with stand wind speed upto 150km/hr. Completion of Work as directed by Engineer-in-charge.

M/S J.V. CONSTRUCTION