general fund work

Amount

Earth work open excavation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc., as per SS 20 A. TNDSS NO: 23 & 24 VI (S2) VI,VII 9,10 with standard specifications. (I.No.61)

Collection supply and filling of M.SAND filling approved quarry including cost and Conveyance of all materials to site and all labor charges for filling etc., Complete.

Plain Cement Concrete 1:4:8 Mix (one part cement, four part sand and Eight part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Supplying and erecting centering to sides and soffits including supports and strutting with necessary cross bracing for plain surface such as RCC slabs rectangular beams all beams lintels etc., centering for soffits upto 3 meter height using mild steel sheet of size 90 cm x 60 cm x 10 mm gauge with MS angles of size 25mm x 25mm x 3mm laid over silver oak (CW) joists of size 10cm x 6cm spaced upto 90cm c/c and casurina props or 10 cm to 13 cm dia spaced at 0.750 cm c/c complying with standard specifications as per TNDSS NO : 30 & 86.

for Square Column

for Grade Beam

Finishing the top of flooring with granolethic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete

Supplying and fabrication of steel and placing in position of TMT steel rods for RCC works as per design given including cost of steel and GI binding wire in all floors etc., complete complying with standard specification in TNDSS NO:97 V,VI (S6) VII (S6), VII-3. V,VI (S6) VII (S6), VII-3.

Reinforced Cement Concrete 1:1½:3 Mix (One part cement, one and half part sand and three part of aggregate)using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing but excluding cost of reinforcement etc. Complete with std. Specifications. TNDSS NO: 30 V, VI (S3), VII-3.

Brick work FLY ASH BRICKS in 230x110x70 mm of size using CM 1:5 Mix including finishing, curing, etc., complete complying with standard specification - 100 cft

Plastering in Cement Mortor 1:5 Mix (one cement, five sand) 12mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Cement paint Two coats with good quality of approved cement paint including cost of all materials to site and all labour charges for mixing applying and proper curring etc., Complete as per Standard Specifications for 10 sqm

Supplying and fixing of M.S grills & Grill gate of approved design for doors, windows and ventilators using necessary mild steel flats for inner and outer members which should be fixed to window frames inclusive of priming coat of best approved quality red oxide primer etc., complete complying with standard specifications

Exterior Emulsion paint Two coats with good quality of approved Emulsion paint including cost of all materials to site and all labour charges for mixing applying and proper curring etc., Complete as per Standard Specifications for 10 sqm

Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2.

Supply and delivery of Open well Submersible pump set lpm 50x60mconforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

Supply and delivery of Three Phase 5 HP panel board with two level guard with auto start suitable for submersible motor and accessorfries including all fitting as per shedules above. Rate inclusive of packing, loadding, freight, unloading, stacking, transit and insurance charges etc., complete

Erection charges to new submersible pumpset LPM and M head 3 Phase with ISI mark IS 14220 without panel board as per spectification

Supply and Delivery of unpasted 75mm PVC pipe 6KSC PVC pipe including cost and conveyance and all other labour charges etc. complete.(TWAD SR 2022-23 )Pg.No21

Lowering the 75 mm PVC pipe 6KSC PVC Rigid pipe into trenches proper grade and alignment including cost and conveyance of all materials and all other labour charges for laying, testing etc., complete. (TWAD SR 2021-22 P.No.248

Refilling with excavated earth including all other labour charges for filling, levelling as per Standard specification etc. complete. (TWAD SR 2021-22 -P.No.265)

Supply and delivery of 65mm dia GM gate valve including cost and conveyance and all othaer labour charges etc compilete (TWAD SR 2021-22 -P.No.45)

Supply and delivery of 65mm dida GI pipe for encasong including cost and conyveyance and all other labour charges etc compltete P.No.40

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading,Unloading ,transportation charges for fixing GI pipes and specialsfor pipe connection works including cutting, threading and fixing charges etc.1000L

Construction of HDPE tank pedestal for 1000 literes Capacity bearing with ISI mark and providing 2nos of 20mm tap connection with checknut washer,nippleb arrangement and 1no 25mm for scover and 1no 25mm for overflow artrangement etc.. And fixing bricks in cm 1:5 for required dia and hieght of 0.6m with pcc 1:4:8 usingh 40mm HBG metal including fixing of inlet arrangements

Dewatering using 3HP to 70HP Diesel engine pumpset including hire chareges cost of diesel,pump[ operator,engine oil,pump operator,labour charges,conveyanance of pumoset etc..at TWAD 2022-23 Pg No 309

Earth work for openwell excavation complying with relevant clauses of TNDSS. Well sinking with lead upto 10 m. in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil.TWAD 2022-23 Pg NO 312