SPL REPAIR TO BLDG AKBAR BK NO. 04 (OTM ACCN) ALONGWITH 02 X BATHROOM BLOCK OF 9 PARA FD REGT UNDER GE (WEST) AGRA

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate bays finished even and smooth without using extra cement plinth protection shall be laid to alternate bay system each bay shall exceed 3m in lentgth 12mm wide and 75mm deep joint sall be filed with hot blown bitumen 85/25 and sand complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in sub base of flooring finished even and fair without using extra cement complete all as specified & directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 20mm thick screed bed CM (1:6) complete all as specified and directed.

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L cement concrete type B-0, 1:2:4 mix ( 12.5 mm graded agg) in, padding, roof kerbs or mud stops, rounded or chamfered on edges coping and similar work, including form work etc all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas,shelves and similar suspended work complete all as specified and directed.

M&L RCC Type B1 1:2:4 Type using (20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and complete all as specified and directed.

M&L Formwork , flat surface to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams etc

M & L for two coats of white wash on new plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M & L for mild steel TMT bar 10mm dia and (Fe-500D) over cut to length, bent to shape required, including cranking, bending spirally, binding wire (0.90mm dia annealed) complete all as specifed and difrected.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified & directed but except brick. Note:- Bricks obtained from item No 12 shall be reused after cleaning.

Brickwork with sub-class `B' brick old size straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified & directed

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying ement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M&L for 10-12mm thick smart care ready mix repair plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacturer instructions )over interior surface of wall complete all as specified and directed.

M&L for 10 to 12 mm smart care ready mix repair plaster is a specially designed ready to use cement-based plaster with high quality polymer additives and well graded sand and fillers wihich can be used for plastering (as per manufacturer instructions) over exterior wall surface complete all as specified and directed

M&L Preparing newly plastered or un plastered surfaces of wall and applying two coats of oil bound distemper with roller application over a coat of primer over a coat of average 1 mm thick wall care putty on new plastered surfaces complete all as specified and directed.

M&L for applying two coats of oil bound distemper with roller on old decorated wall surfaces over 1 mm thick white putty including complete removal of existing treatment with mechanical complete all as specified and directed.

Material & Labour for preparing newly plastered surfaces of wall, applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm including 1 mm putty over new surface of wall complete all as specified and directed.

Material & Labour for preparing Old plastered surfaces of wall, applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm including 1 mm putty over new surface of wall complete all as specified and directed.

Providing Acrylic plastic number plate of size 300mmX 300mm X 3mm and writing building No. of height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws complete all as specified & directed.

Dismantling timber scantling 40 Sqcm and over in section framed work in any position complete all as specified and as directed.

Dismantling structural steel work in cluding doors, gates , framed truss etc. complete all as specified and as directed by Engr-in-charge

S&F in repair 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed.

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etc of grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed..

S&F rolled MS Fe 410W (Gde E-250) quality A for Roof truses (framed), trussed, purlins, crane grantries, rails and fasternings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, clests etc complete all as specified and directed.

S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins ,wind ties and similar small articles confirming to Fe 290 complete all as specified and directed.

Dismentling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. Make :- Tata, JSW, Jindal

S & F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Make :- Tata, JSW, Jindal

Dismentling wall and ceiling board or insulation board /slabs/blanket any thickness including cover fillets.complete all as specified and as directed by Engr-in-charge

S & F Gl frame work grid of size 605 x 605 mm for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section ( up to 2.40 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre Hangers 6 mm dia. G.I. (upto 2400mm length) adjusting level fixed to roof slabs or truss by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified, complete all as specified and directed.

M&L for 4 mm thick non asbestos fibre cement building designer boards fixed in ceiling or laid/inserted to timber/GI/aluminun frame complete all as specified and directed

S & F solid PVC wall lining consisting of 5mm thick wooden grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and complete all as specified and directed. Make :- Rajshri Plastiwood, Giza, Yamuna Interior Pvt Ltd.

S & F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall complete all as specified and directed. Make- Giza / Black Cobra / Rajshri

S&F Louvers Prelam PVC wall panelling of rigiit Upvc foam profiles with integrated skin of size203x30x4.5mm of density 1000kg/cbm manufactured by an ISO 9001-2015 certified compony, having tounge and groove design with inter locking facility, will be fixed in perpendiculor direction at the face wall using 8x38mm steel screwat every 450mm centre to centre covering to avoide leakage through joints.the profile are to b e jointed and finished so as to have a flush lock witch includes filling and finishing with joined comound(Adhesive) between brick wall & wall linning include L/T & C type bedding all as per manufacturers instruction and directed by Engieer -In Charge, complete all as specified and directed . Make :- Rajshri Plastiwood, Giza, Yamuna Interior Pvt Ltd.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L 18/20mm thick any colour granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of stone including rounding and moulding of edge and making hole for cooking gas pipe complete all as specified and as directed.

M&L for coloured glazed ceramic tiles (sutable for internal and external surface) in vertical surface 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed .

M&L colour double charge vertified ceramic tiles 10 mm thick (square/rectangular) area of each tile exceeding 0.42 sqm but not exc. 1.00 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed.

M&L colour double vertified ceramic tiles 10 mm thick (square / rectangular) area of each tile exceeding 0.42 sqm but not exc. 1.00 Sqm as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L non skid joint free coloured tiles (1st quality/premium quality) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11Sqm but not exc. 0.18 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed. (bed room and other room floor)

All as per above Item above but in skirting over 10 mm thick rendering in CM 1:4

M&L Machine cut kota stone 20-25 mm thick as in riser of step, skirting,dado and pillar etc. laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing laid over and including 15mm thick rendering CM (1:4) complete all as specified and directed.

S & F in repairs 15 mm bore chromium plated fancy bib taps long body, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule min weight-400 Gms complete all as specified and directed.

S&F in repair 15 mm bore CP cast copper alloy wall mixer for mixing hot and cold water screwed down for iron pipe and fixed min weight of wall mixer - 1500 gms complete all as specified & directed.

S&F in repairs Vitreous china counter top any shape counter wash basin white size 570mmx410mm oval type incl waste pipe chain plug brackets complete all as specified and directed..

S&F 15 mm bore CP cast copper alloy WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed, min weight of WHB mixer - 1000 gms complete all as specified & directed.

S & F in repair 15mm bore angle valves fancy type CP cast copper alloy with long shank and cup screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S & F Soap dish chromium plated complete all as directed

S&F in repair glass corner shelf with frame triple chromium plated complete all as specified and directed.

S & F in repair tubular towel rail 60 cm length of stainless steel 20 mm Dia with brackets type fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair single piece EWC premium quality with soft closing seat cover including all fixing accessories ,cistern fittings, rim less tornado flushiong size 360x680x750mm, min weight 40-45 kg complete all as specified and directed.

S & F in repair health CP faucet with 15mm dia 1 mtr long flexible tube and wall hook chromium plated complete all as specified and directed.

S&F in repair vitreous china urinals, full stall type FB large, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F urinal glass partition frosted, of thickness 8-10 mm size 900 mm x 450 mm including cost of steel clamp srew etc make Hindware or equalent complete all as specified and directed.

S&F CP brass Urinal spreader for fixing in 15mm pipe complete all as specified and directed.

S & F in repairs CP brass shower rose 125mm dia alongwith shower arm complete all as specified and directed.

S&F in repair 100 mm dia Stainless steel floor trap cover complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed

S&F Waste coupling of CP (half or full threaded) of 32mm bore suitable for wash hand basin complete all as specified and directed.

S&F 32 mm dia PVC waste pipe for wash basin /sinks complete all as specified and directed.

S&F in 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI mark engraved (cylindrical vertical with closed threaded top) hoisted and fixed in position incl dismantling of water tank complete all as specified & directed.

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed.

All as per item No 71 above but 20mm bore

S & F 20 mm outer diameter of CPVC pipes SDR 11 & Plain CPVC SDR 11 including all cpvc brass complete fittings on walls/ceiling or laying in floors complete all as specified.

S&F 20mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed.

S & F in repair 20mm dia Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S & F 15mm to 20mm male Brass Threaded Adaptor (MTA/ MBTA) ) pipes any location complete all as specified.

S & F 15mm to 20mm female Brass Threaded Adaptor (FTA/ FBTA) ) pipes any location complete all as specified.

S & F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and suitable clamp fixed to wall complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends with complete fittings of any radius complete all as specified & directed.

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends with complete fittings of any radius complete all as specified & directed.

S&F 110 mm bore PVC (SWR) single T with access door of any radius complete all as specified & directed.

S&F 110 mm bore PVC (SWR) single Y with access door of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) cowl of any radius complete all as specified & directed.

S & F in repairs 100mm dia of cast iron floor trap, plain with grating incl jointing with solvent fixed with cement concrete type B-1 (1:2:4) complete all as specified and directed complete all as specified and directed.

S & F in repairs 125/110 mm dia of PVC (SWR) Gully trap, plain with grating incl jointing with solvent cement complete all as specified and directed.

S & F in repair stainless steel curtain rods or 25mm dia as in doors/windows SS brackets fancy type including screws and other necessary fitting (Knob) for fixing brackets SS funnels for 25mm dia drapery rod fixed at each end of rods compete all as specified and directed.

S&F for framed work such as grills, grating etc. with ends of bars shouldered and/or riveted or forged into spike, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing framed work of water tank and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

Demolition of old pcc jali including removal of debris from site complete all as specified and directed.

S & F for providing and fixing stainless steel (Grade 304) railing made of hollow tubes channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required ) and fitting the same with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangements for jali complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed.

M&L for Factory made WPC (Wood Polymer Composite) Double Rebated frame of solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madeetc complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid decorative both side laminated type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including fixing with 100mm long stainless steel butt hinges -04Nos with necessary full body threaded star headed counter sunk S.S screws, complete all as per specified and directed.

M&L for providing and fixing factory single extruded WPC (Wood Polymer Composite) solid decorative type wire mesh door shutter four to six panel (pattern as approved by GE) of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant with dual wire mesh aluminium grill for strength and SS wire mes for mosquito). WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. S/S wire mesh and aluminium grill incl in this item.

S& F for aluminium anodised powder coated frame for doors, windows ventilator with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F aluminium powder coated (50 micron thick) door shutter area exc 1.50sqm but nexc 2.5 sqm each fixed to wall with min four number steel fastners, partly glazed with 5 mm thick tinted glass and partly panelled with 12mm thick colouered prelaminated particle board incl rubber beading, joining cleat for fixing in position, with aluminium fixtures; 2 numbers door handle 250 mm long, 1 number barrel tower bolt 200 mm long ,1 number floor door spring & one No 4 liver mortice lock of Godrej of size 100 mm in each shutter all as specified and directed as per following specifications -- (a) Style Section shall be Section No 19560 (b) Top rail Section shall be Section No 19581 (c) Lock rail Section shall be of size Section No 19596 (d) Bottom rail Section shall be Section No 19584 (e) Glazing clip Section No 19370. (f) Top, Bottom and verticle member of shutters will be tightened with hexagonal nut and purpusly made bolt of 10mm dia MS round bar threaded on both the end Note:-(i) size of seciton shall equal to JINDAL section.

Eco-4000 Series windows fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections shoulld be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead shoulld be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window should be provided with grill made of 10mm sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws.

Eco-4000 Series Ventilator fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections shoulld be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead shoulld be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window should be provided with grill made of 10mm sq MS bars welded to at 100mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws.

S & F for factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (styles), with 2,4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet on the front face & 2mm prelam PVC sheet on bach face at site as per specification & drawing complete all as specified and directed.

S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick one side coloured pre laminated other side plain white moulded shutter for kitchen cabinet, cupboard. of density not less than 650 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity ,open edge should be fixed with matching edge bending tap and required frame as per site requirement complete all as specified and directed.

S & F PVC door( back side) stopper 75mm long complete all as spd and dir.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S&F 125mm long aluminium anodised Hasp and Staple, safety type including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 100 mm long stainless steel hinges type B-12 complete all as specified and directed.

S&F Aluminium hydraulic door closer PU coating , double steel adjustment , for soft closing and opening of door, complete all as specified and directed.

S & F 100mm Stainless steel handle for cup board compete all as specified and directed

S&F Continuous (piano) Stainless steel hinges width of flaps (when open) in 40mm, complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described complete all as specified and directed.

M & L for applying one coat of synthetic enamel paint including preparation of old Iron surface of any discription not otherwise discribed over 10 cm width or girth, complete all as specified and directed.

S&F powder coated aluminium partition of specified aluminium section top rail and middle rail, vertical member not less then 2.36 Kg/RM, bottom channel not less then 2.59 Kg/RM including aluminium beads rubber gasket and 5mm thick frosted glass in upper portion and 12 mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination complete all as specified and directed.

M&L for 100mm thick plain cement concrete (1:4:8) type D2 using 40mm graded aggregates as in path, hard standing complete all as specified and directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete,all as specified and directed

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:4 complete all as specified & directed

M&L for applying three coats of white wash on wall including preparation of new plastered or un-plastered surfaces of walls, complete all as specified and directed.

M&L for Cement concrete 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) as in copind , bed block ,in steps floor etc and similar work all as specified and directed.

Supply and fix Eco air ventilator ( wind driven)with 184,000 CFH( cubic feet per hour), 10-30Air changes/hr, MOC of Vanes-Industrial HI grade Aluminium, MOC of Top plates-SS304(0.5mm), MOC of bottom ring-SS304(0.5mm), size of throat-24 inches,body dia 30inches , FRP fixtures, no of vanes-42 Nos Rolled Formed with lock washer, Thickness of vanes-0.5mm ,Shaft and rod made up of Zinc coated steel, Rivets are made up of 5/32 inches x 3/8 inches made of aluminium, rotation technology-Bearing free hardened steel shaft with rotation on single point steady and consistent RPM even after significant passage of time,Venes(blade) are made up of Anodized Aluminium100/1000 0.4mm thickness (0.8 outer side), complete all as specified and directed.

Taking up/down for 25mm bore old GI pipe and connections complete all as specified and directed.

Supply and fix 'Medium Grade' galvanized iron tubes with all fittings such as tees bends elbow etc laid in trenches of 25 mm bore complete all as directed.

Material and labour for drilling and tapping cast iron water mains (in position) for branch connections of the internal 25mm dia complete all as directed.

Excavation in trenches not exc 1.5m width and n. exc 1.5m in depth and getting out for laying of pipes etc in any type of soil complete all as directed.

Returning filling in incl spreading leveling watering and well ramming in layers n.exc 25cm in any type of soil complete all as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n. exc 1.5m above starting point complete all as directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc by cement/ colour /plaster to match with the existing location spot complete all as specified & directed.

M&L for concealed point wiring for one light point /fan point /bell point controlled by one switch (using red, black and green colour coding) complete with 1.5 sqmm unsheathe and multi stranded copper conductor single core FRLSH PVC insulated, 1100 volts PVC insulated unsheathed cable with proper colour coding drawn in through and including PVC concealed conduit not less than 25 mm dia ( medium duty, ISI marked) with all fittings and accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc.including pressed steel powder coated sunken terminal box suitable for modular switch socket (min 60mm deep, suitable size) concealed in wall suitable for fixing modular switches/ socket/ regulator etc, including provn of 1.5 sqmm single core FRLSH PVC insulated multi standed copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ ceiling/ floors etc by using CM (1:3) complete all as specified and as directed. Note:- Modular switches/ socket/ regulator shall be measured and paid separately under appropriate item of AE Part-II.

All as per item No.130 here in before but One socket outlet 5/6 Amps on independent switch board controlled by one switch complete with 2.5 sqmm unsheathed and multistranded copper conductor single core FRLSH PVC insulated, complete all as specified & directed.

All as per item No-130 here in before but One socket outlet 5/6 Amps controlled by one switch on same board with other switches complete it with 2.5 sqmm unshethed and multistranded copper conductor single core FRLSH PVC insulated, complete all as specified & directed.

All as per item No.130 here in before but using 2.5 sqmm PVC FRLS insulated stranded copper conductor cable and for one socket out let 3/6 pin, 15/16 Amps controlled by one 1 way switch on independent board complete all as specified & directed. NOTE-For item No 130 to 134 -: (i)The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc for concealing the conduits to required depth & making good the disturbed surfaces in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at RCC Columns/Beams/Ceilings etc shall be in surface conduit of suitable size fixed on surface with using PVC rawl plug and provision of covering terminal boxes/junction boxes of any shape and size with 3 mm thick bakelight laminated sheet fixed with suitable GI screws and cup washers. (ii) Fittings like switches,sockets,regulators,lamp holders,light fittings shall be measured and paid for separately under appropriate item of schedule A. (iii)The size of conduits shall be determined on permissible no of runs of wires as specified in SSR part-I clause 19.125 (B).However minimum size of conduit shall be 25 mm dia (medium grade).

All as per item No.130 above but using 4.0 sqmm PVC FRLS insulated stranded copper conductor cable and for one socket outlet 3/5/6 pin, 15/16A controlled by one way switch on an independent board complete all as specified and directed.

Supply and fixing modular switch , one way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular switch 16 Amps single pole one way, one module, complete all as specified and directed.

Supply and fixing modular socket outlet 3 pin 5/6 Amps 2 module, complete all as specified and directed.

Supply and fixing modular socket multipurpose 3/5 pin 6/16 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular step type, 2 module electronic fan regulator heavy duty 120watts 240 volts,complete all as specified and directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 4 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 6 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed.

Supply & fixing for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed.

Supply & fix commissioning and testing of complete power cum starter unit compressing of ON/OFF switches socket 3 pin socket outlet with plug top modular type made out of white polycarbonate, fire retardant, UV stabilized power unit internally pre-wired with suitable size copper conductor cable with overload protective device (MCB) complete unit fixed in single polycarbonate housing with inlet & outlet cable port suitable for AC & geyser operated at single phase, 240 volts, 50 Hz AC supply of capacity 20 Amps load bearing capacity complete all as specified and directed.

Supplying and fixing 9/10 watt LED battan surface / wall mounted 4 feet with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block and fixing arrangements for fixing the light fitting, complete all as specified.

Supply and fix lamp holder insulated body with back plate for batten fitting complete all as specified and directed.

Supply and fixing LED Bulb 9 watt, colour temp-6500K, lum output-945lm, Base cap- B22 single phase, 230 Volts AC supply suitable for lamp holder complete all as specified and directed.

Supply and fixing LED luminaire fully diffused, 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light, extruded aluminium housing 11.5mm depth only,edge lit LED panel with light output of 3000 lumen, 25000 hrs life class, 4000k Neutral white light, complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete as specified and directed.

Supply and fixing LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED light warm yellow in colour with a nominal system output of 120 lum/watt (min) with p.f. not less than 0.9 including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in replacement LED Batten of size 4 feet surface/wall mounted with specially designed powder coated aluminium housing,high optically efficient polycarbonate diffuser,in built electronic driver duly wired up to terminal block,power consumption of 20W,luminaire lumen >2000 lm,system efficiency of >120 lumens/W,LED make Nichia/ Cree/ Everlite/ Eclison/ Osram/ lumiled,with LED binning as per ANSI Bin C78.377A,photo biological safety report as per IEC 624718& electrical insulation class 1 Ingress protection IP 20,color rendering index CRI> 80 ,temp range 0 to 450 C ,driver efficiency >85% Power factor >0.9 THD <20% as per IEC 61000-3-2 ,color temp -6500K,Surge protection 2.5 KV,50000 burning hrs (min) as per L7O criteria,two stages isolated constant current operated driver with range 150-270 V AC and safety extra low voltage safe level< 60 V DC as per IEC standard with LM70 & LM 80 certification.

Supply and fix LED sensor batten 20W of size 4 feet, 2000lm power saving LED lighting, smart motion and ambient light sensor, less energy consumption – Lesser Electricity bill & Higher savings Convenience - Bright & Efficient light source with 100lmn/. Complete all as specified and directed.

Supply and fixing 20W Inverter LED batten of size 4 feet with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet,ultra slim square profile liner LED lighting fixture with extruded polycarbonate body with Minimum 8 Watt & Maximum 15 Watt 220 V AC decorative type with driver holder and LED lamp with a nominal system output of 120 lum/watt(min) with PF not less than 0.9, including connecting up with three core flexible copper conductor cable of suitable size complete all specified and directed.

S&F in replacement LED security with aluminum pressure die cast housing, high purity PC fresnel diffuser with silicon gaskets for IP-65 protection, power consumption of 35 W and system efficiency > 100lm /W, in built electronic driver pre-wired upto terminal block with driver efficiency > 85% power factor > 0.95, suitable for external pole upto 35mm LED Make :- Nichia/ Cree / Osram, CRI > 70, ambient temperature range 0-450c, THD<10%, colour temperature 5700K, surge protection cm 3.5KV 50000burning hour as per L70 criteria, multistage constant current constant voltage operated driver with range 150 -270 V AC and safety extra low voltage safe level < 60V DC as per IEC standard including GI pipe light ISI mark of size 25 mm dia length not less than 1.5 mtrs bending to shape for fixing light and nuts, bolts, clamp as required to fix to wall all as specified and directed.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor complete all as specified and directed.

M&L for sub main wiring with two runs of single core FRLSH PVC insulated, unsheathed, multistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLSH PVC insulated, unsheathed, stranded copper conductor cable of size 6.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length complete all as specified and directed.

M&L for sub main wiring with two runs of single core FRLSH PVC insulated, unsheathed, multistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLSH PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length complete all as specified and directed.

Taking down distribution boards any size any type including MCB TPN/SPN/SP/DB etc and making good the disturbed surfaces complete all as specified and directed.

Supply and fix MCB DB vertical type 4 way VTPN sheet metal enclosure 415 volts with 100 Amp fully insulated standard copper bus bar for each face & surrounded with neutral bars and two common neutral bar, two earth bar including cable ties for cable management suitable for housing MCCB TPN 415 Volts as incommer, IP-43, IK-09 as per IEC 61439-3 with metal doors all enclosed on standard steel sheet flush mounting type double door factory fabricated complete without MCB & MCCB but with enclosure blank plate complete all as specified and directed .

Supply and fix in replacement MCB DB sheet metal enclosure factory fabricated double door SPN 4 way with 100 amps rated copper bus bar 240 volts IP-54, IK-09 with metal doors complete all as specified and directed.

Supply and fix in replacement MCB DB sheet metal enclosure factory fabricated double door SPN 8 way with 100 amps rated copper bus bar 240 volts IP-54, IK-09 with metal doors complete all as specified and directed.

S&F MCCB of rating 100 Amp, 4 pole, 415 V, AC fixed type with breaking capacity 25 KA DPX³ 160 type, as per ICE- 60947-1 Ics 100% of Icu, Adjustable tripping: 0 - 0.3 - 1 - 3s with adjustable 70% to 100% and thermal magnetic release to be fixed in existing LT panel for taking In coming electric connection for VTPN DB complete all as specified and directed at site.

Supply and fixing in replacement MCB SPN 240V, 50 Hz, 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity SPN 40 to 63 Amp rating in the MCB DB complete with connection testing and commissioning complete all as specified & directed.

Supply and fixing in replacement MCB SPN 240V, 50 Hz, 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity SPN 32 Amp rating in the MCB DB complete with connection testing and commissioning complete all as specified & directed.

Supply & fix in replacement MCB SP, 40 Amps, 'C' Curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed.

Supply & fix MCB SP, 6 to 32 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN/FP and current carrying capacity 40 to 100A in the DB complete with connection testing and commissioning complete all as specified and directed.

Taking down and fixing only electric metres during the execution of work, complete all as specified and directed.

Supply and fix electric water heater, of capacity 25 Ltrs vertical storage type, outer body of the heater is made with tough ABS material with special inner tank coating that prevents corrosion and rusting and results in a long tank life energy-efficient and Heating Element upto 2 KW (copper tube)-Spiral Type Multiple safety systems for protection against dry heating, overheating and overpressure, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece (hot & cold of length upto 450 mm long with to be fixed on wall with fastener mild steel 100 mm long x 10 mm dia with expansion type split pin and bolts complete for hanging of geyser all as specified and directed.

M&L for electrically disconnecting and taking down existing ceiling/Exhaust fans from any height or in any position from existing bldg and segrate to semi-serviceale & unserviceable & deposit them to the AGE E/M office as directed by Engr in charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 380mm complete all as specified and directed.

Supply and fix ceiling fan, 1200mm sweep, minimum 210 CFM, 230 V, BEE 5 star rated, BLDC (brushless direct current motor ) type complete with standard accessories i.e (three blade, 02 Nos canopy, electronic type modular fan regulator 90 to 100 W, down rod of length 1.5 mtr to 2.0 mtr long, 01 No. fan hock, 02 Nos hanging clamps with rubber real insulator, nuts, lock nuts, bolts, washers, split locking pins etc), double ball bearing, copper wound with synchronous motor, including electrically connecting from ceiling rose to fan connector with 0.5 Sqmm stranded copper conductor 3 core flexible cable cord complete all as specified and directed.

M & L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanized steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Loose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

M&L for rigid non metallic PVC conduit (medium quality ISI marked) 2 mm thick exclusive of boxes (junction/ terminal) 25 mm dia (external) for telephone & TV cable wiring but inclusive of all fittings such as tees, bends, reducers, bell mouth, tube ends and concealed to wall/ roof/ floor complete all as specified and directed.

Supply and fix drawn 2 pair conductor of size 0.5 Sqmm copper PVC insulated and over all screened with tinned copper net and PVC insulated complete all as specified & directed (For Telephone).

Supply and fix dish TV cable cord of size 1.5 Sqmm solid copper conductor triple insulated steel wire mess inner sheathing earth continuity conductor and over all PVC sheathed circular complete all as specified & directed.

Supply & Fix Cable telephone outlet socket switch type flush mounted RJ-11 including modular cover plate and metal flush box complete all as specified & directed.

Supply & Fix Cable TV outlet socket switch type flush mounted including modular cover plate and metal flush box suitable for TV cable cord connection complete all as specified & directed.

M&L for Electric circuits for size of 1.5 sqmm copper FRLS wire for inverter in existing conduit complete all as specified & directed.

Supply and fix medium grade 25mm GI pipe as support member helps in fixing false ceiling mounted exhaust fan and ceiling fans, complete all as specified and directed.

Supply and install mild steel false ceiling mounted rectangular opening vent colour coated polished of dimension not more than 600 X 600mm complete all as specified and directed.

Disconnecting & taking up or down existing unserviceable UG cable/service wire aluminium conductor including GI wire any size and type, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sqmm 4 core.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core.

Taking down fluorescent tube light single/double of any wattage or size street light fittings( post top lantern and LED bollard light) for replacement of burnt/worn out accessories with a new one, complete all as specified and directed. Note: LED lights are not included.

Supplying and laying un-reinforced precast concrete cable cover LV type-I flat size 250 mm x 150 mm x 40 mm in trenches for protection of cable.

M&L for sand cushioning dry fine for cable cushioning below and above the cable complete all as directed at site by Engr- in-Charge.

Supply and fixing GI Pipe 40mm Light grade , for cable protection laid in trench under road or path or fixed on pole or wall with clamps with all fittings complete all as specified and as directed at site.

Supply and fix in replacement LED bollard light with opal acrylic diffuser, 9 W LED, white light & IP 65 protection, complete all as specified and directed.

Supply and fix in replacement post top lantern LED type 40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.

Material and labour for cutting the road for laying of pipe and repair the same with cement concrete work in pavement/hard standing using 400kg of cement per cubic meter all as directed as site.

M/s J S & SONS (BID ID -3466231)

C P Singh and Co (BID ID -3472022)

Parveen Builders (BID ID -3462448)

Ravi Associates (BID ID -3466274)

garg construction company (BID ID -3466622)

M/s Himgiri construction (BID ID -3470743)

M/s Shrangi Rishi Construction (BID ID -3471479)