Creation of Burn unit on the 2nd floor of Trauma Building at NBMCH in the district of Darjeeling. Civil Work

Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m In Second Floor

Dismantling all type of plain cement concrete works, stacking serviceable materrials at site and removing rubbish as directed with in a lead of 75 m In ground floor including roof. Upto 150 mm. thick In Second Floor

In Third Floor

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars, In Ground Floor

Taking out Mirzapur or glazed porcelain tiles carefully by chiselling from walls or floor including stacking serviceable material as directed.

Stripping off worn out plaster and raking out joints of walls, celings etc. up to any height and in any floor including removing rubbish with in a lead of 75 m as directed. .

Removal of rubbish, earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal/Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge.

A. Loading in to trucks at the liffing point, unloading at destination, stacking properly in go downs or yard ect. As directed including carriage by head load up to a lead of 50.00 m at each of the two points. (a) Lime, Moorum, Building rubbis and similar miscellaneous materials.

Carriage of Sand, Moorum and similar materials over pucca road, Any distance up to 5km

Clearing compound premises of shurbs, plants, jungles etc. by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary). (Payment to be made on area cleared)

Brick work with 1st class bricks in cement mortar (1:6) In Super structure, Second floor.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) In Second Floor

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. In Second Floor

Ordinary Cement concrete (mix 1:1.5:3) with graded stonechips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety. In Second Floor

In Third Floor

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel. OTHER Manufacturer not specified (Second Floor)

Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. (a) Pakur Variety.

Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification

Roof treatment by application of non toxic polyurethane modified acrylic based single component (P U Roof Coat) solvent free, cold applied polyurethane modified elastomeric waterproofing membrane with excellant UV resistant capasity as per ASTM D6083fa water based 100% acrylic elastomeric emulsion polymer latex coating used as protective coating for roofs} after preparing the surface by cleaning and repairing the roof cracks by cement & sand mortar (1:4), preferably with antishrinkage mortar (to be paid separately) if any, apply two coats along with a Priming coat (two coats of P U Roof Coat and one coat of primer coat compatible with main product as per manufacturers specification) and reinforced with or without 20 gsm Geotextile Fleece, including the cost of primer coat and base preparation, tools & Plants but excluding the cost of scaffolding and stagging complete as per direction of Engineer -in-charge. (Note: If Geotextile Fleece not uesd ,the rate would be reduced by Rs. 5/-per Sqm)

Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately)

Taking out shutter of door and window, dismantaling by parts (for repair or replacement of damaged parts), reassembling and refitting and rehanging same with old fitting but with new screws as necessary.( where different part of same shutter are renewed under different item, payment under item 73 will be made once only).

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals). In First floor (d) Sal : Local.

Supplying solid flush type doors of deluxe decorative (both side) quality,conforming to I:S 2202 timber frame consisting of top and bottom rail and sidestyles of well seasoned timber 65mm wide each and the entire frame fitted with27.5mm wide battens places both ways in order to made the door of solid coreand internal lipping with teak, mahogony or rose wood approved decorativeveneers using phenol formaldehyde as glue etc. complete, including fitting, fixingthe shutters in position but excluding the cost of hinges and other fittings. (a) 35mm thick shutters (single leaf) ( In 2nd. floor)

Providing and fixing PVC Door Frame of size 50x47mm with a wall thickness of5mm (± 0.2 mm) made out of single piece extruded PVC profile, with mitred cutjoint sand joint with 2 nos. of PVC bracket of size 190 mm x 100 mm long arms ofcross section size 35 mm x 15 mm & self driven self taping screws, the verticaldoor profiles to be reinforced with 40x20mm M.S. rectangular tube of 0.8 mm ,including providing EPDM rubber gasket weather seal throughout the frame,including jointing 5 mm PVC frame strip with PVC solvent cement on the back ofthe profile. The doorframe to be fixed to the wall using 8 x100mm long anchorfasteners complete, all as per manufacturer‟s specification and direction ofEngineer -in- charge.

Providing & fixing factory made 30 mm thick factory made solid pvc door shuttermade out of single piece extruded solid pvc profile . The style & rails shall be ofsize of 75 x 30 mm having wall thickness of 5 mm. The style and top bottom railshall have one side a thickness of 15 mm integrally extruded on the hinge side ofthe profile for better screw holding power. 15 mm thickness shall be of singlepiece extruded solid pvc profile whereas it shall be not be made of sheet pastedprofile) . The styles and rails shall be reinforced with MS tube of size 18 mm(±)1mm x 18 mm (±) 1mm x 1mm painted with primer all four corners ofreinforcement to be welded or sealed . solid pvc extruded bidding (push fit type)will be set inside the styles and rails with a cavity to receive single piece extruded5 mm pvc sheet as panel. The styles and rails will be metered cut and join with thehelp of pvc solvent cement, self tapping screw and braket of size 200 x 75 mm /welded at each corner. Single piece extruded solid pvc lockrail of size 100 x 30mm with a wall thickness 5 mm & 15 mm integrally extruded in the middle oflockrail & fixed with styles with the help of PVC solvent cement & self driven selftapping screws of size 100mm x 8mm complete as per manufacturersspecifications and direction of Engineer-in-Charge. b) Factory made Single piece extruded PVC profiles door shutter of both sidelaminated wood grains decorative Finish:

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) (a) 40mm x 6mm, 250mm Length .

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (vii) 100 mm x 58 mm x 1.90 mm.

Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S.205/66) and fitted and fixed with cadmium plated screws:. (iv) 75 x 63 x 3.2 mm.

Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. 150 mm long x 10 mm dia. bolt.

100 mm long x 10 mm dia. bolt.

Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete, (iii) 300mm x 16mm dia. bolt.

(i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete : (a) Heavy type (I.S.I. size 3).

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. (a) With continuous plate base (hexagonal/round rod). (vii) 150 mm grip x 12 mm dia rod.

(ii) 100 mm grip x 10 mm dia rod .

Supplying, fitting & fixing of Aluminium fixed partion wall of all aluminium sections viz top, bottom and side member, intermediate member, glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983 and IS: 1285-1975, annodized conforming to IS:1868- 1983, fitted with all other accessories viz. EPDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium fixed partition wall with glass / panel board all complete as per architectural drawings and direction of Engineer-in-charge. (Excluding cost of glass/ panel board, 10-12 Micron thickness Annodizing film. Natural white. a) for unsupported length of vertical member upto 1.50m. height of both ends of vertical member restrained but panel with in 0.90 sqm (unit wt of Top, bottom & side member @1.366 kg/m ; intermediate member @ 1.443 kg/m; glazing clip: 0.167 kg/m respectively) [Note : for estimate purpose construction wing may consider weight of Al-Sections for Partition wall @ 5.7 Kg per Sq.M]

Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge. 10-12 Micron thickness Annodizing film Natural white 2 Track Aluminium Window

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium section for the following units:-. Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all other necessary arrangements for fixing the partition to walls, floors, beams, columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge I) For partitions using section of size: a) 63.50 mm x 38.10 mm

Partly glazed partly panelled or fully glazed single leaf aluminium swing door made of extruded and anodised alloy aluminium sections, fabrication, including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages, with top pin assembly of approved make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries , cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated / particle block ) fixing them with glazing clips as per drawing , specification and direction of Engineer-in-Charge. (Add. above ground floor - 1st. floor)

Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column,beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers. i ) 2 track sliding window.

Supplying, fitting, Fixing Fly / Mosquito proof nylon net on any type of window, door shutter frame with necessary fixing arrangements complete.

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (A) In 10-12 Micron thickness Annodizing film I) Natural white h) Louvered window. (i) Top, bottom and side member.

(ii) Louvered Section

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium section for the following units:-. (v) Louvered window.

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs . In First Floor

Supplying, fitting and fixing windows and ventilators with or withoutintegrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-frictionprojecting type, box type hinges, glazing clips, lugs locking bracket,handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20mm down cutting holes and mending good damages to match withexisting surface complete in all respect excluding glazing.(Add extra @ 1.2 % for each additional floors upto 4th floor and @1.5% for each addl. Floor above 4th floor.)In Ground floorFlash butt welded windows and ventilators(No shop priming will be allowed to facilitate inspection ofworkmanship)Without integrated grill (b) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only] In Ground Floor

In First Floor

(vi) steel peg stay 300 mm long including fitting and fixing. In Ground Floor

In First Floor

Renewing M.S. members of steel shutters by welding including taking out the old, mending good damages complete, including taking out and refixing the glass panes.

Easing, oiling and adjusting the steel shutters including scraping all members and fitting so as to make the shutters easily operable (no extra payment will be made for taking out and fixing glass, if necessary).

Renewing hinge of steel shutter including taking out old one by cutting and fixing new hinges by welding and mending good damages complete.

Renewing two point steel plated or oxidised handle of steel doorsand windows as directed including painting complete.

Supplying bubble free float glass of approved make and brand. Conforming to IS: 2835-1987. (i) 4 mm thick coloured / tinted / smoke glass.

ii) 5 mm thick clear glass.

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). b) In First Floor: Sizes-600 mm x600mm x10 mm with breaking strength > 1500 N

Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. (a) Area of each tile above 0.09Sq.m. Coloured decorative In Second Floor

Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (i) with 1:6 cement mortar. (b) 15 mm. thick plaster. ( SF)

(i) with 1:6 cement mortar. (b) 20 mm. thick plaster. GF Mkd N

In First Floor

In Second floor

(i) with 1:4 cement mortar. (c)10 mm. thick plaster. (In Ground Floor)

In First Floor

In Second floor

Acrylic Distemper to interior wall, ceiling with a coat of solvent basedinterior grade acrylic primer (as per manufacturer's specification)including cleaning and smoothning of surface.Two Coats

Removing old scales, blisters etc. of interior surface of walls, ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary). To make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge).

Protective and decorative Acrylic exterior emulsion paint of approved quality , as per manufacture specification as per direction of EIC to be apply over Acrylic primer as required. the rate included cost of material , labour scaffoldic and all incidential charges but excluding the cost of primer.( two coat). Premium 100% Acrylic emulsion. (a )Ground Floor

(b ) First Floor

(c) Second Floor

Applying exterior grade Acrylic primer of approved quality and brand on plaster or concrete surface old or new surface to receive decorative textured (mat finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly complete as per manufacturer's specification and as per direction of the EIC. (a )Ground Floor

(b ) First Floor

(c ) Second Floor

Scraping of moss, blisters etc. thoroughly from exterior surface of walls necessitating the use of scraper , wire brush etc.(payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge.).

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. (a) On timber or plastered surface: (1) With super gloss (hi-gloss). (iv) Two coats (with any shade except white).

(b) On steel or other metal surface: (1) With super gloss (hi-gloss). (iv) Two coats (with any shade except white).

(b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

(b) Priming one coat on timber or plastered surface with synthetic enamel oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) (i) 3 mm thick (weighing 7.4 kg/Sq.m)

Extra for fixing glass panes in steel window.

Supplying, Fitting & fixing different factory made Metal Craft Sheet (excludingcost of metal crafting) incluing cost of powder coating (for M.S, Aluminiumplate) & finished metal sheet with all fitting accessories complete in all respectas per diection of Engineer-in-Charge. Aluminium Plate iii) 0.5mm thick -

Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in Ground Floor. {White cement and Pigment to be supplied by the Agency] (a) With Makrana plain pink / Adranga Pink / Garbh Gulabi / Udaypur pink / Udaypur Green / Black Bhaslana (iii) Area of each Slab/tile exceeding 0.60 sq.m but not exceeding 1.00 sq.m. In 2nd Floor

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, consisting of floor and ceiling channel 50/51 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on for board as per manufacture‟s specification and direction of engineer in charge all complete ii) 70 to 71 mm overall thickness partition using 10 mm thick High pressure steam cured non-Asbestos multipurpose Cement Board reinforced with cellulose fibre (Density>1250kg/m3) manufactured through autoclaving process as per IS: 14862 with suitable fibre cement screws.

Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (a) 3mm thick (0.25mm Al.+2.5mm LDPE +0.25mm Al. PVDF coating)

Supplying fitting & fixing frames for Fire resistant door shutters made of 1st class Malaysian Hardwood (densified to 810 kg/cum) and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 psi pressure as per IS:401 and kiln seasoned to moisture below 15% as per IS:1141 of section 120 mm X 70 mm spray quoted with 2 coats of intumescent paint of minimum 200 micron, with single row of Brush- Type intumescent strip of size 10 mmx 4 mm affixed in the slit of the Frame for fire and smoke sealing, etc. complete as per direction of Engineer -inCharge including a protective coat of painting at the contact surfaces of the frame excluding cost of concrete,Iron butt hinges and M.S clamp at Ground Floor. [Note : Specific permission of the Superintending Engineer is required for execution of this item] 2ND Floor

Supplying & fitting of 55mm thick asbestos free-fire, heat and smoke resistant composite Fire check Door Shutter complying with fire performance FD120 as per IS:3614(part-II)-comprising of 2x8 mm Calcium Silicateboards over Chemicallytreated(withFireretardantchemicalsinpressureimpregnation vessels under 160psi pressureas per IS:401and kiln seasoned tomoisture below15%asperIS:1141) internal timber(MalaysianHardWood,densifiedto 810kg/cum) frameworkof100mmx32mmwith32mmthickinfillofceramic fiber(density128Kg/cum),vermaculitemixfacedwith3mmFireretardantHig Density fire board, internally lippedwith hardwood beading, and pasted in HydraulicPressunder25MPa,spraycoatedwith2coatsof in-tumescentpaint ofminimum300micron,andwithsinglerowof Brush-Typeintumescentstripof size10mmx4mmaffixedonperipheral slit onall edges of shutter excep bottom for fire and smoke sealing , without any external lipping including fitting,fixingshuttersinpositionbutexcludingthecostofhinges&otherfittings asperdirectionofEngineer-in-chargecompleteinallrespectinGroundFloor [Note : Specific permission of the Superintending Engineer is required for execution of this item. ] 2ND Floor

Supplying, fitting and fixing shower of approved brand and make. Hand shower(Health Faucet) with 1mtr Fexible Tube with wall Hook (Equivalent to code No.573 & Model-ALLIED of Jaquar or Similar)

Supplying, fitting and fixing bib cock or stop cock. a) (ii) Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / Sumthing Special of ESSCO or similar brand)

(b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supply of PVC pipes & fittings of Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with G.I. Pipes as per IS:1239 (Part-I). P.V.C Pipes. 50 mm.

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. Specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc.

Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer. 2000 litre capacity.

Labour for lowering plastic water storage tank and stacking in places as directed. Above 1500 litre upto 5000 litre capacity. From 1st floor to G.L.

Extra for each additional story

Labour for hoisting plastic water storage tank. Above 1500 litre upto 5000 litre capacity. Upto 1st story from G.L.

Extra for each additional story

Labour for punching hole in plastic water storage tank upto 50 mm dai.

Supply of Chlorinated Polyvinyl Chloride (CPVC ) pipes &fittings conforming to IS-15778: 2007 (I) Tank connecting nipple, 40 mm

(N) Union 40 mm

(Q) Ball Valve 25 mm

(Q) Ball Valve 40 mm

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. (A) UPVC PIPES. (ii) 110mm Dia.

(B) UPVC fitting:. (c ) Bend 87.5 degree (ii) 110mm Dia.

(B) UPVC fitting:. (d) shoe. (ii) 110mm Dia.

Cleaning and disinfecting upto 2000 litre water tank including mansonry reservior.

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) For Exposed Work, P.V.C Pipes, a) 15 mm..

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (ii) 470 mm X 280 mm X 340 mm

Wash basin white vitreous china of approved make (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm wood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. 550 mm x 400 mm size.

Supplying, fitting & fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P.nut, 15mm dia. 750 mm long.

Supplying, fitting and fixing approved brand 32mm dia P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. 1050mm long.

Supplying, fitting and fixing pillar cock of approved make. CP Pillar Cock with 200 mm extended Lever Handle (Equivalent to Code No. 5031 & Model - FLORENTINE of JAQUAR or similar brand).

a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets (a) Sink only, (ii) 630 mm X 550 mm X 180 mm

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). 530 mm X 410 mm.

Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts,nuts etc. With 'P' trap.

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws supplied, fitted and fixed complete. Anglo Indian Plastic (hallow type) white.

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 . Single socketed 3 meter length. 100 mm.

Single socketed 3 meter length. 160 mm.

Fittings. Door Tee. 160 mm.

Fittings. Pipe Clip. 160 mm.

Pipe Clip. 110 mm.

Fittings. Reducing Tee 160 x 110mm. 75mm..

Fittings. Reducer 110 X 75 mm 75 mm

Fittings. W.C. Connector (450 mm long) W / lipring 75 mm

Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any foor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Enginer-in-charge) Payment will be made on centre line measurement of the total pipeline including specials.). Above ground. 110 mm dia.

Above ground. 160 mm dia.

Supplying, fitting and fixing 32 mm dia. flush pipe of approved make with necessary fixing materials and clamps complete. Polythene Flush Pipe.

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm.

Supplying, fitting and fixing towel rail with two brackets. C.P. over brass. (ii) 25 mm dia. and 600 mm long

Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed. For 100 users:-. Within a lead of 150 metre.

Cleaning soak pit by removing the top slab and replacing inner filling with jhama bats and reparing the pit as necessary including fitting the slab.

Cleaning silt of inspection pit.

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm(depth) with 250 mm thick 1st. class brick work in cement mortar(4:1) on all sides, bottom of the pit consisting of 100 mm thick cement concrete(1:6:3) with stone chips over a layer of jhama brick flat soiling, 15 mm thick (1:4) cement plaster to inside walls and outside walls upto G.L. and 20 mm thick(1:4) plaster to bottom of the pit, providing necessary invert with cement concrete(1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster(1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. With Pakur veriety (OTHER MANUFACTURES NOT SPECIFIED)

Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directon of Engineer-in-Charge. For 100 users. With Pakur variety (OTHER MANUFACTURES NOT SPECIFIED)

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work(6:1) band all round and cement brick work(6:1) upto 0.90 metre from top with 19 mm thick cement plastering(4:1) to inside face upto the depth of cement brick work, 12 mm thick cement plaster(4:1) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal(50 mm to 63 mm size) including R.C.C. cover slab of designed thickness with cement concrete(4:2:1) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making necessary arrangements for pipe conections, excavation of well including shoring, dewatering and remeving the excess earth from the premisis as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work(6:1) and 1.00 m. inside dia. (OTHER MANUFACTURES NOT SPECIFIED)

Modular Monoblock Wall, Ceiling & Corner Panels for Modular O.T. :- The Wall, Ceiling and Corner Panel made of Modular Monoblock Panels, having Front Side of 0.8 mm G.I. Sheet and Back Side of 0.6 mm G.I. Sheet, both side should be factory powder coated to prevent it from rusting. All Panels should be injected with Poly Urethane Foam (PUF) with a minimum density of 40 Kg/m3 and should be sealed with Aluminum Extrusion to make the structure rigid. Total thickness of the Wall Panel will be 50 mm and Ceiling & Corner Panel will be 30 mm. The Corner Panels should be factory fitted with Ducting and Return Grill Cut-outs for easy connection. Each OT must have Cascade Pressure Stabilizer having multi 304-Graded Stainless Steel Blades to control air pressure. The Sheet should be from TATA/JINDAL/SAIL or equivalent reputed make and Panels should be from JINDAL MECTEC/ JDV / ALTOS or equivalent reputed make. The rate includes cost of all materials, fixtures, labour, installation charges, transportation cost, VAT & all taxes complete in all respect as per direction, instruction and approval of the Engineer-in-Charge.

Paint to Modular O.T. (2 Coats) :- Spray painting 2 coats with a water based aseptic and self-sterilizing wall coating system of 300 microns with priming after necessary filling of all joints and cavities with Metallic Epoxy Filler and sanded flush to provide a jointless finish. Anti-Microbial Protection: These product hygiene coatings start the biocidal action as soon as the microorganism land on the surface, and prevents the growth of mould, bacteria and yeasts for at least 5 years. This Hygiene coating is independently tested by leading universities to demonstrate resistance. Life Cycle Savings : The unparalleled durability of our hygiene coatings helps to extend the maintenance cycle and to minimize all related material, labour and shut down costs. The speed with which they can be installed and the ease of subsequent maintenance also create significant cost savings. Chemical Persistence : These hygiene coatings should be highly resistant to abrasives, detergents and weak acids and alkalis used in cleaning regimes. Furthermore, they can be regularly steam cleaned without any loss of performance or ion to the substrate. (Make - Liquid Plastic UK/SKK JAPAN or eqivalent). The rate includes cost of all materials, labour, application charges, transportation cost, VAT & all taxes complete in all respect as per direction, instruction and approval of the Engineer-in-Charge.

Preparation of as-built drawings includes dimensioning and nomenclature of various buildings, consisting of floor-wise floor plans detailing walls, windows, doors, staircases, and lifts, along with elevation and sectional views in both longitudinal and transverse directions, as well as a site plan illustrating the approach road, entry and exit points, internal driveways, and side open spaces..

GST @ 18% of Estimated cost

Labour Wellfare Cess @1% of Estimated cost with GST

Please Enable Macros to View BoQ information