SPL REPAIR TO ENGINEER OFFICER MESS AT HQ CE JAIPUR ZONE AT JAIPUR MIL STN

Amount

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for precast cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate) block masonary with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

M&L for cutting into old masonry (buil in cement mortar) to form toothing for and bonding in new brick or stone work including making good in cement mortar of the same mix as for new walling complete all as specified and as directed.

Taking down cement plaster on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M & L for rendering 15 mm thick in CM 1:6 on stone masonary surface or surface other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 10 mm thick in CM 1:3 on concrete surface of ceiling finished even and smooth without using extra cement cement complete all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces or on surface other than fair faces of brick masonary in two layers, first layer 10mm thick in CM 1:6 and top layer 5mm thick in CM 1:4 mixed with water proofing compound as per manufacturers instructions and finished even and smooth without using extra cement including necessary scaffolding arrangements up to any height complete all as specified and as directed. Note : WPC Shall be measured and paid seperately

Supply only integral water proofing compound complete all as specified and directed.

M&L for preparation of newly plaster surface of wall and applying two coat of premium exterior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over and including one coat of alkali resistant priming paints over and incl 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

M&L for preparation of newly plaster surface of wall and applying two coat of premium interior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over and including one coat of alkali resistant priming paints over and incl 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

- ditto- all as per srl item No 11 above but in ceiling complete all as specified and directed.

M&L for complete removal exising treatment on old plastered surfaces of wall by mechalical means and scraping down smoke root mould moss and efforescent salts and treating oil and greasy spots as applicable, preparation the surafce and applying two coat of premium exterior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over and including one coat of alkali resistant priming paints over and incl 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

M&L for complete removal exising treatment on old plastered surfaces of wall by mechalical means and scraping down smoke root mould moss and efforescent salts and treating oil and greasy spots as applicable, preparation the surafce and applying two coat of premium interior emulsion weather proof paint (ready mix) of approve shade and tint using hand roller over and including one coat of alkali resistant priming paints over and incl 1mm thick (avg thickness) wall care putty including rubbing with suitable sand paper to make the surface smooth complete all as specified and directed .

- ditto- all as per srl item No 14 above but in ceiling complete all as specified and directed.

Taking up or down 15mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed

Taking up or down 20mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed

Supply, laying, jointing and testing 16mm outer dia CPVC pipe SDR 11 & Plain CPVC SDR 11 fittings, as per IS:15778 on walls/ceiling or laying in floors complete all as specified and directed. Note : (i) The quoted rate shall be included all plain CPVC fittings and pipe cutting, fixing with CPVC solvent cement and testing. (ii) Special fitting i.e. CPVC brass fitting shall be measued and paid seperately as supply only under respective item of BOQ

Supply, laying, jointing and testing 20mm outer dia CPVC pipe SDR 11 & Plain CPVC SDR 11 fittings, as per IS:15778 on walls/ceiling or laying in floors complete all as specified and directed. Note : (i) The quoted rate shall be included all plain CPVC fittings and pipe cutting, fixing with CPVC solvent cement and testing. (ii) Special fitting i.e. CPVC brass fitting shall be measued and paid seperately as supply only under respective item of BOQ

Supply only Brass Elbow for 16mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass Tee for 16mm outer dia CPVC pipe complete all as specified and directed.

Supply only Male Brass Threaded Adaptor (MTA/ MBTA) for 16mm outer dia CPVC pipe complete all as specified and directed.

Supply only Female Brass Threaded Adaptor (FTA/ FBTA) for 16mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass UNION for 16mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass Elbow for 20mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass Tee for 20mm outer dia CPVC pipe complete all as specified and directed.

Supply only Male Brass Threaded Adaptor (MTA/ MBTA) for 20mm outer dia CPVC pipe complete all as specified and directed.

Supply only Female Brass Threaded Adaptor (FTA/ FBTA) for 20mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass Tank Adaptor for 20mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass UNION for 20mm outer dia CPVC pipe complete all as specified and directed.

Supply only Brass BALL VALVE for 20mm outer dia CPVC pipe complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for double charge/ultra charge vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm but not exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed.

M&L for double charge/ultra charge vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm but not exc 1.00 sqm on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for coloured glazed ceramic tiles 450mm X 300mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for coloured jointfree non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exc 1.50 sqm and n.exc 4.00 sqm each complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window (Area not exceeding 2.00 sqm each) Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware : Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories for fixing of window complete all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVCextruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S & F Factory made gauge panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; but wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firml in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

Supply and fix Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. Note:Butt hinges shall not be paid separately

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and as directed.

S&F Rebated mortice lock, brass, 4 lever, vertical type, size 100 mm complete all as specified and as directed.

S&F for 5.5 mm thick sheet glass odinary qulity and glazing with neoprene beading exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

Taking down eaves gutters,sanitry PVC pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed.

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F 110 mm dia UPVC (SWR) bends any radius complete all as specified and as directed.

S&F 110 mm dia UPVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed.

S&F 75 mm dia UPVC (SWR) bends any radius complete all as specified and as directed.

S& F UPVC (SWR) gully traps of size 125/110 setting and jointing with solvent cement complete all as specified and directed.

S&F UPVC (SWR) floor trap oulet dia 75mm, plain with grating including jointing with solvent cemet complete all as specified and as directed.

S & F stainless steel commercial grease trap waste oil and water separator for kitchen having min size of 60x30x30 cm including all fitting and fixture complete all as specified and as directed. Make : Green genra pvt ltd, subam ett, shree Ent, Nugreen

S& F in repair hand made double bowl kitchen sinks with drainage board made of 304 grade staineless steel of min size (1210 x 510mm) having bowl size min (480x460mm) and (300x460mm), depth min 230mm and installation under mount including chromium plated brass coupling for sink fitting including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe and fixture complete all as specified and as directed. Make : Cera, Kohler, Hindware

S&F in repair tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S& F Stainless steel peg stay six complete all as specified and as directed

S&F PVC Connections 15mm size 600mm long with PTMT nuts complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin with pedestal white flat back size 550 x 400 mm excluding taps, waste pipe, chain & plug and porcelene stopper but including brackets /fastners, brass chromium plated waste coupling, cutting for and pinning in ends of brackets, fixing of pillar tap complete all as specified and directed.

Supply only 15mm bore pillar tap, long body cast copper alloy, chromium plated, fancy type with capstan head, screwed down, high pressure with or without lettered 'Hot' or ' Cold' with long screwed shank and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repair UPVC (SWR) floor trap oulet dia 110mm, plain with grating including jointing with solvent cemet complete all as specified and as directed.

S&F in repair SS Grating doom 125 mm dia with or without waste hole complete all as specified and as directed.

S & F in repair 15mm bore sink mixer, brass, chromium plated, fancy type for mixing hot & cold water, bright finish screwed the ends for iron pipe and plugging complete all as specified and directed.

S&F in repair 15mm bore stop/angle valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repairs PVC waste pipe flexible 32mm dia having length of 450 mm for WHB/sink/urinal etc complete all as specified and directed.

S & F in repair 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc complete all as specified in SSR Part I and directed by Engr in charge.

S&F in repair 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) land complete all as specified and as directed

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid bedded and pointed in any mortar complete all as specified and directed .

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8, type D-2(40mm graded aggregate) as in sub base complete all as specified and as directed.

M & L for 50 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floors complete all as specified and directed.

M & L for 25mm to 30mm thick precast concrete rubber moulded heavy duty parking tile of minimum size 300mmx300mm minimum M-35 grade, confirming to IS 1237:2012 fixed in position incl necessary vibration etc complete with gray cement and pigment, laid over and incl 15mm thick screed bed in CM (1:4) as specified and directed.

M&L for Providing precast cement concrete louvers and jallies, 35 mm thick (measured solid) including all mouldings but excluding frame, type B-0 1:2:4 (12.5 mmgraded stone aggregate) set in CM 1: 4 incl complete all as specified and directed.

M&L for providing precast cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets,cover slabs (for man holes etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar 1:6 complete with joints to match complete all as specified & directed.

Dismantling boarding plywood etc of any description and in any position fixed with nails etc complete all as specified & directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain shutter, cabinets etc of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and including fixing with stainless steel hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note : Hinge shall be paid seperately

S & F auto close hinges, stainless steel of grade SS-304 , bright finish fixed complete all as specified. Make : Godrej, Hindware, Lifetime or equivalent

S & F stainless steel (Grade SS-304) telescopic basket guide/sliding channels suitable for running basket, bright finish complete all as specified & directed. Make : Godrej, Hindware, Lifetime, Hettich or equivalent

S & F stainless steel handles of size 100 mm fancy type of approved make complete all as specified & directed. Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) prerforated cutlery basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Cup & saucer basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plain basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plate/thali basket, fancy type of size 18" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plain basket, fancy type of size 18" x 20" x 6" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plain basket, fancy type of size 18" x 20" x 8" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S&F in repair 25 mm dia SS (grade 304) drapery/curtain rod medium weight incl taking down old one with finials, brackets etc complete all as specified and directed

S&F SS -304 grade brackets/ end brackets for holding drapery rod all as specified and as directed.

S&F SS Finials suitable for 25mm dia SS 304 grade drapery rod as approved complete all as specified and directed

Taking down carefully surface aluminum /copper point wiring, casing capping /PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable, single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one light point controlled by one, one way switch 6 Amp complete all as specified and directed.

,---ditto--- all as per item No. 99 here-in-before but for one bell point controlled by one bell push 6 amps one way complete all as specified and directed.

,---ditto--- all as per item No. 99 here-in-before but for one 3 pin 5 Amp socket outlet controlled by one switch on same board complete all as specified and directed.

,---ditto--- all as per item No. 99 here-in-before but for one 3 pin 5 Amp socket outlet controlled by one switch on indepdendent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one 16 Amps socket outlet point controlled by one swith on independent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one 20 amp, single pole & neutral, socket outlet with 2 pole and earth, metal enclosed plug top complete all as specified and directed.

M&L for sub main wiring with two run of 6 Sqmm single core, PVC insulated, unsheathed, FRLS multistranded copper conductor cable alongwith one run of 6 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non-metallic PVC conduit of 25mm dia, ISI marked, ivory colour with fitting / fixing accessories of suitable size as required including making connection as required incl taking down old wiring complete all as specified and directed. NOTE - Two run of 6 sq.mm phase and neutral wire, One run of 6 sq.mm earth wire & One run of PVC conduit with accessories shall be measured as One length.

S&F modular switch, 6 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular switch 16 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular socket, 6/16 Amps, 2/3pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F modular socket, 6 Amps, 2/3 pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F modular hum free electronic step fan regulator 120-280 volts of 120 watts capacity (socket type) including connecting up complete all as specified and directed.

S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed.

S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed by Engr-in-Charge.

S&F in repair MCBs Distribution board SPN, 8 ways, powder coated CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCBs and MCB DB shall be of the same make.

S&F in repair MCBs Distribution board tripple pole and neutral (VTPN) 4 ways, powder coated, CRCA steel sheet, suitable for MCCB incomer upto 160amp, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 250 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make.

S&F MCBs of 'B' curve, single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs of 'B' curve, Double pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs of 'C' curve Double pole, 40 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCCB four pole, 63amp, 415 volt, adjustable type, with breaking capacity 16KA, thermally adjustable between 70 to 100% including 4 spreader link set of same make as that of MCCB including reqd cable connections with copper lugs of suitable size and testing & commisioning and make good complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F LED batten (0.6m) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 900 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed.

S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, 5 star rated in white colour with BLDC fan motor, Min air delivery 210 CFM with service value 6.00 BEE, incl blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

S&F exhaust fan, high speed, steel body 300mm sweep, 1400 RPM, four blade, heavy duty motor, copper wound double ball bearings, grey colour with louver, nuts, bolts and washers incl three core 0.75sqmm copper cable connection with protective steel bird guard complete all as specified & directed.

M&L for taking out ceiling fan 1200mm sweep 50Hz AC 230 volts and refixing at new location including minor repair and replacement of fan blade, down rod, nut, bolt and washer and spray painting in existing colour including 0.5sqmm thre core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required and writing MES No. on fan body complete all as specified and directed.

S & F in repair 20amp, single pole and neutral socket outlet, with 2 pole and earth, metal enclosed plug top in powder coated CRCA steel sheet enclosure recess mounted with chained matel cover for socket out let with and incl one single pole B curve MCB 16 Amps complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire size 4.0mm upto 7.5 m included in the item).

S & F 40 mm bore GI tubing "light grade" with all fittings, fixed to wall/ pole with suitable size MS clamp, nut, bolt, washer etc or laid under road crossing etc as reqd for protection of cable incl painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed. Note : Cost of MS clamp, nut bolt, washer and GI fittings etc shall be inclusive in the quoted rates.

Supply, laying, jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC sheathed, galvanised steel strips or wire armoured, heavy duty electric cable with multi stranded aluminium conductor, 1100 volts grade cross sectional area 35sqmm, 3.5core confirming to IS:7098 (part-I), laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt, washers, saddle etc complete all as specfied and directed. Note : The cost of AI thimbles / lugs and cable gland etc is included in quoted raes.

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth for foundation, etc. or for laying of cables n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Removing excavated soil to a distance n. exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as directed.

Returning, filling including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as directed.

M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge. Note : Punned thickness shall be considered for payment purpose.

M & L bricks for protection cover to UG cable (with old size sub class B bricks, designation 75) with width equal to length of brick, laid dry and flat abutting each other with gaps between adjecent bricks not exceeding 10mm complete all as specified and directed.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

Rakesh Choudhary Contractor (BID ID -3366377)