SPECIAL REPAIR TO SEWAGE LINE, MAN HOLES, SEPTIC TANK AND SOAKAGE WELLS AT SE FALLS INCLUDING CERTAIN SANCTIONED WORKS AT SHILLONG UNDER GE SHILLONG

Amount

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out of soft / loose soil etc complete all as specified and as directed.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in soft/loose soil and getting out complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and directed.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M&L for PCC (1:4:8), type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and as directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) (using 20mm graded crushed stone aggregates ) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) ( using 20mm graded crushed stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 ( Nominal mix) ( using 20mm graded crushed stone aggregates ) as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete 1:3:6 type C1, using 20 mm graded stone aggregate, exc 10 Cm width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete 1:3:6 type C1, using 20 mm graded stone aggregate, 10 Cm width and setting in cement mortar 1:4 complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n.exc 63mm deposited , spread and well levelled in layers not exc 15 cm thick water, rammed to a true surfaces etc complete all as specified and directed.

M&L for sand filling 100 mm thick under floor including watering and consolidation complete etc complete all as specified and directed.

S&F Polythene film, black, 50 micron, laid in floor over sand filling etc complete all as specified Sqm and directed

M&L for 75 mm thick PCC 1:4:8 type D-2 ( using 40 mm graded stone aggregate) as in sub base of floor , finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 ( using 12.50 mm graded stone aggregate) 25 mm thick ,as in floor , finishing even and smooth with using extra cement etc complete all as specified and as directed.

M&L for vitrified ceramic tiles, light shade, 10 mm thick ( square / rectangular) polished, area of each tiles n.exc.0.36 sqm in floors, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including screed bed 15 mm thick in cement sand mortar ( 1:4) etc complete all as specified and as directed.

All as per item no 21.00 here in above but as in vertical surfaces such as wall, skirting and dado etc set and jointed with neat cement slurry and pointed in white or colour cement to match with the colour of tiles over and including 10 mm thick backing course cement sand mortar ( 1:4) etc complete all as specified and as directed.

M&L for pre polished factory made pavement chequred cement concrete tiles of size 300mm x 300mm x 20-22mm thick, set, jointed and pointed in neat cement slurry in floors , over and including 20 mm thick screed bed ( 1:4) etc complete all as specified and as directed.

M&L for rendering 10mm thick in cement sand mortar 1:6 on fair faces of brick Walls or on concrete surface,finished even and smooth without using extra cement etc complete all as specified and as directed.

M&L for Rendering, 15 mm thick plaster in cement sand mortar ( 1:4), in two layers, top 5 mm thick with approved Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a coat of 10 mm thick base coat complete all as specified and as directed by Engineer-in-Charge. Note WPC shall be measured and paid separately.

Supply only integral water proofing compound, ISI marked.complete all as specified and as directed.

M&L for mild steel framed works such as in tubular trusses , purlins, gantries, rails and fastening and heavy framing ( Beam, Tee, angle, channel or flat section ) including distance pieces , cleats , special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 etc complete all as specified and as directed.

M&L for mild steel works such as Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates and similar work conforming to Fe-290 Gde E-165 etc complete all as specified and as directed.

M&L for Painting two coats of Synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surfaces of any description, over 10 cm width or girth including preparation of surfaces etc complete all as specified and as directed

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strngth of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour etc complete all as specified and as directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick having tensile strngth of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and as directed

M&L for preparation of new plastered surfaces and applying two coats of weather coat paint over and including a coat of alkali resistance primer etc as per manufacturer instruction all as specified and directed.(Make Apex ultima" of Asian Paints or equivalent in Berger / Shalimar / Nerolac.

M&L for preparation of new surfaces of wall and applying two finishing coats of oil bound distemper over a coat of alkaline resistant primer including and over a thin layer of wall care putty etc complete all as specified and as directed.

Providing & fixing false ceiling of designer tile ivory painted of 4mm thickness (as pe IS : 14862) of size 595 x 595mm and any one of the design in true horizontal level or sloping suspended in inter locking metal grid of hot dipped galvanised steel section consisting of main 'T' runner with suitably spaced joints to get required length and 25 x 30mm made from 0.30 mm thick sheet spaced at 1200mm C/c and cross 'T' of size 25 x 30 mm made of 0.30 mm sheet 1200 mm long spaced between main 'T' at 600m C/c top form a grid of 1200 x 600 mm and secondary cross ''T'' of length 60 mm and size 15 x 32 mm made of 0.30 m thick sheet to be interlocked at middle of the 1200 x 600 mm panel to form grid of 600 x 600 mm and wall angle of size 24 x 22 x 0.40 mm and laying false ceiling tiles in the grids including, required cutting / making, opening for services like diffusers, grils, light fitting , fixtures,smoke detectors etc. Main ''T'' runners to be suspended from ceiling using GI soffit cleats fixed to existings RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200 mm c/c main 'T' bototm exposed width of 15mm of all ''T'' sections of 4mm dia GI wire shall be pre-painted with polyeste paint and black painted groove at center of size 4mm depth and 4.5mm width all height etc complete all as specified and as per directions of Engineer-in-charge.

M&L for 2nd class hard wood as in plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and as directed.

S&F 35 mm thick Flush shutter, solid core construction with block board core and both faces covered with decorative face veener with lipping / frame to match etc complete all as specified and as directed by Engr-In-charge.

S&F 2nd class hardwood glazed and skeleton shutters 35mm thick ,open rebated and prepared to receive galss, glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded. fitting with cut and mited beads for securing glass, etc, size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) supplied and fitted to chowkats etc complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer etc compete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of apperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and as directed.

M&L for PCC 1;3;6 type C2 (using 40mm gradeed aggregate) as in side filling, anchorage , blockage or fixing of hold fast etc complete all as specifed and as directed.

M&L for Framed MS work such as grills, gratings, etc.. with ends of bars shouldered and /or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

M&L for MS works such as bands, straps, supports or stays for clamps; flat iron of size 25 x 23 mm thick as in hold fasts; wall ties; and similar small articles conforming to Fe-290 Gde-E-165 etc complete all as specified and as directed.

S&F MS butt hinges, medium weight 100mm, cold rolled and fixed with stainless screws etc complete all as specified and as directed.

S&F Alumunium alloy, anodised, sliding door bolt 300mm with hasp, staple (bolt type) and each fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast -allumunium alloy and fixed with anodised screws etc complete all as specified and as directed.

S&F Allumunium, handles 150mm, cast type anodised. fixed with anodised screws etc complete all as specified and as directed.

S&F powder coated (min powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed

S&F powder coated (powder coating min 50 micron) anodised aluminium sliding / openable type window shutter of any track , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , packing , screws, aluminium push handles with special auto lock , anodised aluminium snap beading screws for fixing glass etc complete all as specified and as directed.

S&F sheet glass 4.8 mm thick, ordinary quality and glazed with oil putty in square exc. 0.5 sqm in each pane etc complete all as specified and as directed.

M&L for PCC 1;3;6 type C-1 (using 20mm graded aggregate) as in plinth protection ,75 mm thick , finished even and smooth without using extra cement etc complete all as specifed and as directed.

Surface dressing n.exc 15 cm deep in soft / loose soil etc complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 ( nominal mix) ( using 20mm graded crushed stone aggregates ) as in slabs supported on walls, beams and columns in floors, roofs, landings and in shelves and the like etc complete all as specified and as directed.

M&L for Formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landing and similar items (horizontal or sloping), rough finished flat surfaces etc complete all as specified and as directed.

M&L for 5mm thick cement plaster in cement sand mortar (1:3) on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement etc complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash etc complete all as specified and as directed.

M&L for Non-skid ceramic colour tiles 7 to 8 mm thick , (square/rectangular), joint free, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of the tiles over and including 15 mm thick screed bed in cement sand mortar 1:6 complete all as specified and as directed.

M&L for Glazed ceramic Coloured tiles of size 300mm x 450mm x7mm or 300mm x 600mm x7 mm thick as in Skirting, dados, etc.set and Jointed in neat cement slurry and pointed in white or colour cement to match laid over and including a backing coat of 10mm thick screed bed in cement sand mortar 1:4 etc complete all as specified and as directed.

S&F factory made pre laminated solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I complete all as specified and directed

S&F Solid PVC door frame of size 50 mm X 47 mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, etc complete all as specified and as directed .

S&F Butt hinges, extruded brass, with galvanised mild steel hinge pin, bright polished, 100 mm size.(type C-22) etc complete all as specified and as directed.

S&F 100 mm long aluminium anodised barrel tower bolt of extruded section and fixed. etc complete all as specified and as directed.

S&F 100 mm size extruded aluminium alloy handles, febricated type, anodised. etc complete all as specified and as directed.

S&F Vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm including bracket, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of adequate length and dia and PVC connection 15mm size 450mm length with PTMT nuts, complete all as specified and as directed by Engineer-in-Charge .Make:- Prayag cat part no. 4645 IRIS or equivalent make of Parryware / Hindware.

S&F Vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including PVC water closet seat cover closed pattern with flat bottom and cover with PVC hinge device, flushing pipe, fixing bolt for pedestal pattern and making good to disturbed surfaces of floor etc complete all as specfied and directed. Make:- Prayag cat part no.4022 or equivalent make of Parryware / Hindware.

S&F PVC (Plastic polymer flushing Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge .Make:- Prayag cat part no. 503 or equivalent make of Parryware / Hindware.

S&F PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and as directed.

S&F 15 mm bore angle cock, brass chromium plated, fancy type with round headed knob, suitable for 15mm bore iron pipe screwed for iron pipe complete all as specified and as directed. Make:- Jaquar CON 167 KN or equivalent model from make Prayag / Hindware.

S&F CP Bib tap 15 mm bore, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down, high pressure, screwed for iron pipe complete all as specified and as directed. . Make:- Make:- Prayag Cat part No.7606 or equivalent model from make Sona / Hindware.

S&F Pillar tap,15 mm bore, brass chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge Make:- Prayag cat part no.7602 or equivalent make Hindware / Sona.

S&F GI tubing 15mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F GI tubing 20 mm dia medium grade with all necessary GI fittings ,fixed in wall, ceiling or floor with necessary clamp or hook complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) soil, waste and vent pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S&F 75 mm bore PVC (SWR) soil, waste and vent pipe pipe, single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S&F tinted sheet glass , 5 mm thick ordinary quality and glazing with snap beading fixed in aluminium door / window / ventilator etc complete all as specified and directed.

S&F steel ventilator with top hung shutter with or without glazing bar, including hinges, fixing lugs,steel peg stay etc complete all as specified and as directed

M&L for preparation of new or previously untreated surfaces of ceiling and applying three coats of white wash including necessary preparation etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of white or tinned with cement base paint over and including a coat of wall primer etc complete all as specified and directed.

S&F Rotational moulded polyethylene 1000 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position as per SSR Part-I 2009 including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx length 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.Make:- Polycon / Polytuf / Sintex

S&F 3 mm thick, figured sheet glass, pin headed type and glazing with oil putty or wooden beads in squares ,ordinary quality, n.exc 0.5 Sqm in each pane etc complete all as specified and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement sand mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth etc complete all as specified and as directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms ) etc complete all as specified and as directed.

S&F Vitreous China bowl urinal , Half stall, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement sand mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; also including brass chromium plated waste coupling 32 mm dia PVC flexible waste pipe of adequate length and dia etc complete all as specified and as directed.

Demolition of cement concrete ( unreinforced) in ground floors and paving n.exc. 15 cm thickness ( below / above ground level ) etc complete all as specified and as directed.

Excavation in trenches n exc 1.5 m wide and depth exc 1.5 m deep but n. exc. 3.0 m for foundation, etc n exc 10 sqm on plan, in soft/loose soil and getting out complete all as specified and directed.

S&F in repair 160 mm bore PVC (SWR) soil, waste and vent pipe, type B , ISI marked , single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S&F in repair 110 mm bore PVC (SWR) soil, waste and vent pipe, type B , ISI marked , single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S&F in repair 75 mm bore PVC (SWR) soil, waste and vent pipe, type B , ISI marked , single socketed, in any length with rubber ring joint fixed to walls including clamps for securing pipe complete all as specified and directed .Make:- Prince / Supreme.

S & F in repair 110 mm bore PVC (SWR) junction single T equal or unequal with access door etc complete all as specified and directed

S & F in repair 110 mm bore PVC (SWR) bend / door bend of any radius jointed with cement solvent or cement joints etc complete all as specified and directed

M&L for Block masonry with solid precast cement concrete blocks made out of cement concrete 1:3:6 type C1, using 20 mm graded stone aggregate, exceeding 10 Cm width and setting in cement mortar 1:6 including demolition of old unserviceable one etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in coping ,benching of manholes or work of similar nature etc complete all as specified and as directed.

Taking down cement plaster on brick, concete or stone walls etc inlcuding racking out joints, hacking for key, scrubbing down with water etc including removing debris from site complete all as directed.

M&L for precast RCC 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in cover slab and set in cement sand mortar 1:6 including necessary formwork and demolition of old unserviceable one etc complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) as in surface channel and drain, , finished even and smooth without using extra cement including demolition of old unserviceable PCC etc complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150 mm / 200 mm bore of pipe etc complete all as specified and as directed.

M&L for Construction of PCC Block masonary Soakage wells , excavation in any type of soil, foundation in PCC 1:3:6,type C-2 using 40 mm graded stone aggregate, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonry in cement sand mortar (1:4) , RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8M dia x 3.0M effective depth complete all as specified and as shown in Drg No. TD/SZ/502 / Sheet no. 1/1 and as directed. Note:- Rate quoted against ibid item shall be deemed to be included for all types of required works such as earthwork, PCC block walling etc)

M&L for Construction of RCC SEPTIC TANK 50 USERS designed to carry sewage and sludge water, excavation/earthwork in any type soil , PCC 1:4:8 in foundation , vent shaft , connection etc with all fittings & fixtures etc complete all as specified , shown on drawing CESZ / 2019 / STD-01 1/1. and as directed by Engineer in charge.( Note:- The rate quoted against ibid item shall be deemed to be included for all types of required works such as earthwork , etc )

S&F LLDPE SEPTIC TANK 25 USERS designed to carry sewage and sludge water , including necessary earth work ( Excavation of pit approx 600 mm larger than size of septic tank ) in any type of soil, PCC 1:4:8 type D-2 ( using 40 mm graded stone aggregate ) 150 mm thick in foundation, vent shaft, connection etc complete all as specified , as per manufacturer's instruction and as directed by Engineer in charge..

SCHEDULE A PART-II (E/M WORKS) M&L for Point wiring ( concealed type) with two single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked), green colour as continuous earth wire terminated connected to common earth dolly for one light / fan point controlled by one way switch including making good to disturbed wall with using cement sand mortar 1:4 including necessary colour wash / distemper etc complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge .Make of cable:- KEI / RR Kabel / Havells . PVC Casing & Capping:- Prestoplast / Finolex / Kalinga

All as per item No 99.00 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as directed by Engineer -in -Charge .

All as per Item No. 99.00 here-in-above but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.00 sqmm green in colour as earth continuity conductor connected to common earth dolly in PVC casing caping complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, one way 5/6 Amps complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, one way 15 / 16 Amps complete all as specified and directed.

Supply and fix socket outlet (ISI marked), 2/3 pin and 5 Amps, 240 volts complete all as specified and as directed.

Supply and fix socket outlet (ISI marked), 2/3 pin and 15 Amps,240 volts, flush type complete all as specified and as directed.

S&F recess mounted low glare luminaire 28 watt PLUTO NEO 2 x 2 complete with all necessary accessories etc complete all as specified and as directed. Make Havells Cat part No. PLUTONEO2X2PLR28WLED857S or equivalent make in Bajaj / CG

S&F Decorative wall mounted LED batten fittings with all accessories, 1X18 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed. Make Havells Cat part No. LHEXBQP71N1W018 or Make:- CROMPTON Cat Part No. LCTL 18 CDL.or Bajaj cat aprt no.BCLSB 18 WH.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

Supply and fix MCB Distribution board , 240 volts ,TPN ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link,8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer -in- Charge. Make : Havells / Legrand / L&T.

Supply and fix MCB Distribution board , 240 volts ,SPN ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link,8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer -in- Charge. Make : Havells cat part no. DHDPSHODRW08 or equivalent make in Legrand / L&T.

Supply and fix MCB TPN, 415 Volt, 63 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Make : Havells cat part no. DHMGCTNF063 or equivalent make in Legrand / L&T.

Supply and fix MCB DP, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Make : Havells cat part no. DHMGCDPF040 or equivalent make in Legrand / L&T.

Supply and fix MCB SP, 240 Volt, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Havells cat part no. DHMGCSPF040 or equivalent make in Legrand / L&T.

Supply and fix MCB SP, 240 Volt, 06-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Havells cat part no. DHMGCSPF006-032 or equivalent make in Legrand / L&T.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size etc complete all as specified and directed.(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- KEI / RR Kabel / Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I.

S&F Bulkhead 10 watt LED light fittings , ultra modern , energy saving, surface mounted, decorative oval shape , modern design utility for indoor and outdoor application with IP 65 protection etc complete all as specfied and as directed by Engineer -in -Charge, . Make:- Havells Cat Part No.RUGBYNEONFT10WLED860SSYMTOPC or equivalent model from Havells / Bajaj.

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 25 Sqmm 4 Core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed.

M&L for Sand cushioning with dry clean river sand for protection/covering of under ground cable in trenches or as acushion bedding and haunching to PVC pipes including necessary watering and consolidation etc complete all as specified and directed by Engr-in-Charge. Note:- Punned thickness only shall be measured for payment.

Supply and laying Sub class 'B' well burnt brick, laid flat in trenches as protection to LT XLPE cable complete all as specified and as directed.

Supply and laying GI tubing light grade,40 mm bore with all fittings, fixed complete to walls and ceiling or laid in floor for cable crossing complete all as specified and as directed.

M/s A L Traders