8241-SPECIAL REPAIR TO BLDG NO T-5 EMBARKATION HQ (AIR BRANCH) GST ROAD CHENNAI AND CERTAIN OTHER SANCTIONED WORKS UNDER GE STM

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard / dense soil complete all as specified and as directed

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation, laying pipes etc or for shaft, walls, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil all as specified and as directed

Excavation over areas not exceeding 1.5m deep and getting out in hard/dense soil all as specified and as directed

Excavation over areas exceeding 1.5m deep but not exceeding 3.0m deep and getting out in hard/dense soil all as specified and as directed

Returning, filling in including spreading, levelling, watering and well ramming in layer not exceeding 25cm in soil complete all as specified and as directed by Engineer-in-Charge

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

Excavating post holes (or similar holes) each n exc 0.5 cu m, getting out in hard/ dense soil, including removing surplus soil to a distance n exc 50m and making good surface.

Material and labour for moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick spread, levelled and rammed including watering all as specified and as directed by Engineer-in-Charge.

Material and labour for hardcore of gauge not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface of broken stone or boulders all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4 type B-2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

Material and labour for reinforced cement concrete 1:2:4, type B1 (Nominal mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete etc complete all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Supply & Fix Mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps,bases, splices, angle brackets, cleats and other connections conforming to Fe 410-W (Gde E-250) quality A

Supply & Fix mild steel screw bolt 5 to 10mm dia machine made hexagonal hed at one end and screwd the other, or scrwed both end to be fitted with washers and one hexagonal nut exc 5 cm but not exc 10 cm long

Material and labour for reinforced cement concrete design mix (M-30 grade) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete etc complete all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Material and labour for reinforced cement concrete 1:2:4, type B1 (Nominal mix) using 20mm graded stone aggregate as in walls, retaining walls, basement walls, ballast walls and the like, any thickness, above top of footings, including attached pilasters and buttresses etc complete all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Material and labour for reinforced cement concrete design mix (M-30 grade) using 20mm graded stone aggregate as in walls, retaining walls, basement walls, ballast walls and the like, any thickness, above top of footings, including attached pilasters and buttresses etc complete all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Material and labour for reinforced cement concrete 1:2:4, type B1 (Nominal mix) using 20mm graded stone aggregate as in column, pillar, pier post etc all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Material and labour for reinforced cement concrete 1:2:4, type B1 (Nominal mix) using 20mm graded stone aggregate as in roof beams and lintel bands etc all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Material and labour for reinforced cement concrete 1:2:4, type B1 (Nominal mix) using 20mm graded stone aggregate as in slab all as specified and as directed by Engineer-in-Charge. Note : Reinforcement shall be measured and paid separately.

Material and labour for providing precast reinforced cement concrete, 1:2:4, type B-1 (using 20 mm graded stone aggregate) for manhole / drain covers etc., set in cement mortar 1:6 and finishing the exposed faces even and smooth without using extra cement including necessary form work etc complete all as specified and as directed by Engineer-in-Charge. Note : Form work and reinforcement shall be measured and paid separately.

Material and labour for cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in coping, bands, string course etc including weathering, slightly rounded or chamfered angles and throating and necessary form work etc complete all as specified and as directed.

Material and labour for plain cement concrete design mix M-20 grade using 20mm graded aggregates 100mm thick as in top surface of raft slab all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm internal bore pipe etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required for exceeding half brick but not exceeding one brick thick walls etc complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work/stone/PCC block masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for fly ash brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for fly ash modular brick work straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Supply only liquid water proofing admixture

Supply only integral water proofing compound

Material and labour for formwork to sides of concrete foundations, footings bases of columns, sides and soffits of foundation and plinth beams and similar work rough finished surfaces of concrete flat all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, vertical or to better rough finished all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surface of concrete rectangular all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

Material and labour for form work to soffits of suspended slabs such as roof slabs and similar work not exceeding 200mm thick in flat rough finished surfaces of concrete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frame with shutters exceeding 1.5 sqm not exceeding 4.00 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Taking down chowkats or frame with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing to stores complete all as specified and as directed by Engineer-in-Charge

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 160 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engineer-in-Charge.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 156 of SSR Part II (pertaining to item No 08080) etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix factory made solid PVC Moulded door shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good in cement concrete in frame complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 35mm thick factory made plain framed panelled shutter 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 35mm thick 2nd class hard wood glazed and skelton shutter, open rebated prepared to receive glass, gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.22 (a) complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 15 micron powder coated anodised aluminium sections for sliding or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note:- (i) Glass panes /wire mesh will be measured & paid separately as "supply only" (ii) Rubber beading will not be weighed.

Supply and fix powder coated anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminum fittings such as roller, channel, locks/handle complete all as specified

Material and labour for Mild steel TMT bars 10 mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia by placing in position new reinforcement bars including tack welding to existing reinforcement bars complete all as specified and as directed by Engineer-in-Charge

All as per item No 42 described here-in-before but 5mm dia and over upto and including 10 mm dia in stirrups spaces and binders

Supply and fix Welded steel wire fabric supplied and fixed complete to wood or steel members n exe 4kg etc complete all as specified and as directed

Supply and fix Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, Fe-410-W(Gde-E-250) quality-B cleats complete all as specified and as directed.

Dismantling structural steel work including doors, gates of any description not otherwise provided for etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam , tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding 990or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 290 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge.

Material and labour for mild steel framed work such as grills, gratings, framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc., with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, and similar works confirming to FE 290 Gde E-165/FE-410-W(Gde E-250) all as specified and as per directed.

Suply & Fix Mild steel work in tubular trusses, Pulins, Postm, diatance pieces incl spl spaced washer etc complete using ERW or induction but welded tubes Confirming to IS1161-1979 Gde ST-240.

Supply & Fix mild steel roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings & heavy bracket framing (beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc to confirming to FE-410-W (Gde-250) Qty A

Supply and fix mild steel work as in hold fast & similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

Dismantling AC corrugated sheets in roof covering including ridges complete all as specified and directed by Engineer-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Material 7 labour for sand filling under floors incl spreading ang and levekling in layers N exe 25 cm thick, watering and constalidation

Material & Labour machine pressed pre cast contrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade of cement concrete of with grey cement and pigment all as specified and directed by Engr-in-Charge.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Supply and fix butt hinges, medium weight, cold rolled mild steel, 100mm long all as specified and as directed.

Supply and fix butt hinges extruded aluminium alloy with stainless steel type, anodised and fixed, type C-21, 100 mm long all as specified and as directed.

Supply and fix stainless steel butt hinges, medium weight 100mm size fixed with stainless steel screw to aluminium frame complete all as specified and as directed

Supply and fix aluminum anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and as directed

Supply and fix aluminum anodised, barrel tower bolts of extruded section 200 mm long complete all as specified and as directed

Supply and fix extruded aluminium alloy handles, fabricated type, anodised 150 mm long complete all as specified and directed.

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy 250mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium windows and wooden door shutters etc complete all as specified and as directed by Engineer-in-charge.

Supply and fix tubular towel rail brass chromium plated 20mm dia, 'D' type, 60cms long between flanges fixed to walls with screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs tubular towel rail brass chromium plated 20mm dia, 'D' type, 60cms long between flanges fixed to walls with screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 25mm dia aluminium coloured powder coated decorative fancy type curtain rods all as specified and as directed.

Supply and fix aluminium coloured powder coated decorative fancy type end bracket and knob for 25mm curtain rods all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C2, using 20mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including joints of plinth protection filled with bitumen mastic (1:3) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 100mm thick PCC (1:4:8) type D2, (using 40mm graded stone aggregate) as in sub base, finished even and rough complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick PCC (1:4:8) type D2, (using 40mm graded stone aggregate) as in sub base, finished even and rough complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in 40mm thick flooring, finished even and fair all as specified and as directed.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc all as specified and as directed.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm (size of tile 600 x 600 mm ), in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non - skid Ceramic coloured jointless tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including cement rendering 10 mm thick in CM 1:3 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for joint free, coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm , on vertical surfaces etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including cement plaster 10mm thick in CM (1:4) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for chequered cement concrete tiles 20cm x 20cm x 25mm thick set, jointed and pointed neat cement slurry in floor with grey cement and pigments , including 20mm thick screed bed in cement mortar 1: 4 all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 15 mm thick in cement mortar 1:4 on concrete / brick masonry surfaces and finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick in cement mortar 1:6 on concrete / brick masonry surfaces and finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 10 mm thick in cement mortar 1:6 on concrete / brick masonry surfaces and finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 10 mm thick in cement mortar 1:4 on concrete / brick masonry surfaces and finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 5 mm thick in CM 1:3 on concrete surfaces as in ceiling, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished even and smooth without using extra cement mixed with water proofing compound as per manufacturer's instruction all as directed. Note: water proofing compound shall be measured and paid separately

Material and labour for preparation of surfaces plastered or unplastered on new surfaces on walls and applying two coat of cement base paint over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment on external walls surfaces and applying two coat of cement base paint over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of plastered or unplastered decorated wall surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of plastered or unplastered decorated ceiling surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing plastered or unplastered old decorated surfaces of wall and applying one coat of white wash complete all as specified.

Material and labour for complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over 1.5mm thick (average) layer of interior wall care putty including preparation complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints / Berger (Bison)

Material and labour for preparation of new or previously untreated steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer etc complete all as specified and as directed.

Material and labour for preparation of new or previously untreated wood surfaces and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Material and labour for preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of wall primer etc complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparing surfaces of wood and wood based materials of any description and treated with tar or coal tar black paint treating ends of posts backs of chowkats etc area tarred exceeding 0.1 sqm but not exceeding 0.5 sqm each etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing surfaces of wood and wood based materials of any description and treated with tar or coal tar black paint treating small articles such as stop covers gully gratings holdfasts ends of posts backs of chowkats etc area not exceeding 0.1 sqm each etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC (SWR) single socketed in any length, type B, with rubber ring joints, 75mm dia, laid in trenches / floor or fixed in walls complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC (SWR) single socketed in any length, type B, with rubber ring joints, 110mm dia, laid in trenches / floor or fixed in walls complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC (SWR) bend 75 mm bore complete all as specified and as directed

Supply and fix PVC (SWR) bend 110 mm bore complete all as specified and as directed

Supply and fix PVC (SWR) Tee 110 mm bore complete all as specified and as directed

Supply and fix PVC (SWR) floor trap with grating including jointing to solvent cement waste pipe 75 mm dia complete all as specified and as directed

Supply and fix PVC (SWR) multi floor trap with grating including jointing to solvent cement waste pipe 75 mm dia complete all as specified and as directed

Supply and fix PVC (SWR) vent cowl 110 mm complete all as specified and as directed

Supply and fix brass chromium plated 32 mm bottle traps for urinals with inlet and outlet screwed for pipe or connections including necessary packing, union complete all as specified and as directed

Supply and fix galvanised iron pipe, medium grade, 15 mm bore with all fittings and connections and fixing to walls including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed.

Supply and fix in repairs galvanised iron pipe, medium grade, 15 mm bore with all fittings and connections and fixing to walls including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed.

Supply and fix galvanised iron pipe, medium grade, 20 mm bore with all fittings and connections and fixing to walls including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed.

Supply and fix in repairs galvanised iron pipe, medium grade, 20 mm bore with all fittings and connections and fixing to walls including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed.

Supply and fix galvanised iron pipe, medium grade, 25 mm bore with all fittings and connections and fixing to walls including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 all as specified and directed.

Supply and fix 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

Supply and fix 15mm bore pillar taps, fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe all as specified and as directed.

Supply and fix in repairs 15mm bore pillar taps, fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe all as specified and as directed.

Supply and fix angle cock fancy type 15 mm bore chromium plated with long shank and cup (Concealed type) high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and as directed.

Supply and fix in repairs angle cock fancy type 15 mm bore chromium plated with long shank and cup (Concealed type) high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and as directed.

Supply and fix vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap and connection to trap and to flushing pipe, anti-syphonage pipe etc and provision of lime concrete bedding complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap and connection to trap and to flushing pipe, anti-syphonage pipe etc and provision of lime concrete bedding including making good to floor etc complete all as specified and as directed by Engineer-in-Charge

Supply and fix vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs plastic water closet seat, coloured, closed pattern with flat bottom, and cover and MS CP or aluminium hinging device etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, including flush pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, including flush pipe of polyethylene of low or high density or PVC 32mm dia complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs CP brass shower rose 125mm size suitable for 15mm bore pipe complete all as specified and as directed by Engineer-in-Charge

Supply and fix Chromium plated health faucet with connection and hook fixed complete all as specified and as directed by Engineer-in-Charge. Make :Parry ware Cat No .T9937A1 or equivalent.

Supply and fix toilet paper holder material brass finish glossy complete all as specified and as directed by Engineer-in-Charge. Make: Prayag, Cat No .BA-38 or equivalent.

Supply and fix vitreous china white wash hand basin flat back of size 550 mm x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste coupling, waste pipe etc. Including cutting for and pinning in ends of brackets or erecting stand including 32mm bore waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms) complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed

Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed

Dismantling of 1000 Ltr water tanks

Supply and fix rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 500 ltrs capacity with inlet & outlet connections, tank nipple, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 1000 ltrs capacity with inlet & outlet connections, tank nipple, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 25mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fix in repairs Ball valves 25 mm high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm - 210gms / 25mm-455gms/ 40mm- 690gms) complete all as specified and as directed.

Supply and fix 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed

Supply and fix in repairs 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed

Supply and fixing gun metal gate valve 50mm bore with ISI mark and iron wheel head screwed in both ends for GI pipes

Material and labour for Salt-glazed stoneware drain pipes 150 mm dia laid in trenches and jointed with spun yarn and cement mortar 1:1 etc complete all as specified and as directed

Material and labour for plain cement concrete 1:3:6, type C2 using 40mm grade stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC (SWR) Gully trap, 125/110mm with grating including jointing with solvent cement etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 4mm thick sheet glass with 12mm square beading, ordinary quality, in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-Charge.

Material and labour for anodised aluminium snap grid frame work for false ceiling conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, 4mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm, cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system with and including 12mm thick gypsum board with all connected accessories suitably placed in false ceiling grid with necessary design in single / double as per manufacturers instruction including taking down existing false ceiling with snap grid etc complete all as specified and as directed by Engineer-in-Charge. Make of Aluminium sections: Hindalco / Jindal / Associated Profile & Aluminium / Indal (Indian Al Coy) Make of Gypsum board :Mangalam Timber Product / Gypsum Board / Jolly Bd, Mumbai / Indian Gypsum product / Armstrong World Industries

Removing the existing roof treatment of any description completely and remove all the debris from site and rubbish off the premises complete all as specified and as per directed.

Material and labour for cement screed bed 20mm thick in cement mortar 1:4 with using 3% of waterproofing compound by weight of cement all as specified and as per directed.

Material & labour for water proofing treatment with APP modified prefabricated five layer water proofing membrane, not less than 3mm thick and weighing not less than 3.00 Kg/Sqm reinforced with non woven polyester matt black finished over compatible primer at 0.3 litre/Sqm, touching the membrane on whole surface uniformly while unrolling the membrane by LPG and sealed with trowel after necessary preparation of surface complete all as per manufactures instructions and finally finished with a coat of bit mastic aluminium paint over the membrane. The over lap joint shall be provided of 75mm in longitudinal direction and 100mm in transverse direction respectively. All the angles, abutments and the drainage outlets shall be sealed with extra care to ensure full bondage all as specified and as per directed. Note: The work shall be carried out be authorised applicators of manufactures Manufactures : IWL India Ltd/SAPL (ARGO-P) Hydrotech Ltd (Hydroflame)/STP.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceilingroses, pendants, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as directed

Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including non metallic rigid PVC conduit, PVC conduit fittings and conduit accessories fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including modular terminal box with white cover plate with frame for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly all as specified and as directed :-

One light point controlled by one switch.

One Ceiling fan point controlled by one switch and one regulator.

One 3 pin 5 amps switch socket on independent board.

One 3 pin 5 amps switch socket on same board along with other switches.

One exhaust point controlled by one switch

All as per item No.148 above but with4 sqmm copper conductor cable with 2.5 sqmm PVC copper conductor cable as earth continuity conductor for one socket outlet 15/16 amps controlled by one switch 15/16 Amps on independent board all as specified and as directed.

Supply and fixing wall mounted LED batten,Extruded aluminium housing provided efficient heat disipation with polycarbonate diffuser with integrated electronic driver high efficacy.short circuit & voltage cut off protection, wide opearting voltage range of 140V to 270V wide, lumen output of 2350,22W including lamp with complete all as specified and as directed. Make : as per HAVELLS CATALOGUE No: LUMILINEPLUSBS20WLED865SPCSS/ PHILIPSB1021LED25S6500PSUGRST/CROMPTONRETRO LED T5 LT5RT-18-CDL/Bajaj :BCLAB SP 22L LEDCWPC SD

Supply and fix Wall mounted LED Batten, extruded Aluminium heat sink provided for efficient heat dissipation & integrated electronic driver of Lamp type: 20W LED life time of 30000* hours including lamp all as specified and as directed.

Supply and fixing wall mounted LED batten,Extruded aluminium housing provided efficient heat disipation with polycarbonate diffuser with integrated electronic driver high efficacy.short circuit & voltage cut off protection, wide opearting voltage range of 140V to 270V wide, lumen output of 1050,10W including lamp with complete all as specified and as directed. Make : as per HAVELLS CATALOGUE No: LUMILINEPLUSBS10WLED865SPCSS/ PHILIPSB1021LED10S6500PSUGRST/CROMPTONRETRO LED T5 LT5RT-9-CDL/Bajaj :BCLAB10 WH

Supply and Fix Endura PEARL 30 W MP Bldg Sec lights New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP 66 roadway luminarie with high power LEDs as light source and electronic driver of Lamp type:30W LED 6000K all as specified and as directed.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fix MCB Distribution board,,415 Volts 4 way , TP&N , verticle , double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with Bus bars, Neutral Links and Earth Bar fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Standard/Legrand/L&T

Supply & Fix MCB TPN 415 volts,32 amps 'C' Curve 10 kA Capacity all as directed.Make: Standard/Legrand/L&T

Supply & Fix MCB SPN 230 volts, 40 amps 'C' Curve 10 kA Capacity all as directed. Make: Standard/Legrand/L&T

Supply & Fix MCB SP 230 volts, 40 amps 'C' Curve 10 kA Capacity all as directed. Make: Standard/Legrand/L&T

Supply & Fix Ceiling rose surface bakelite 65mm x 50 mm two to three terminals all as directed.

S & F Modular switch 1 way 6A, 1 module, 240 Volts complete all as specified and directed

S & F Modular switch 1 way 16A, 1 module, 240 Volts complete all as specified and directed

S & F Modular Socket, 16/6 A - 3 pin Socket 2 module complete all as specified and directed

S & F Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed

S & F Modular Fan step regulator 120 watts - 2 module one module

Taking down old heavy model ceiling fan depositing to MES Store yard (GE STM) by own transportation including Supply and hanging Ceiling fan 1200mm sweep energy saving model BLDC complete set with suitable regulator including connecting to ceiling rose with twin twisted flexible copper cable and provisioning of suitable down rod includuing all accessories as per site requirment Make : Havells Efficiencia Neo (BLDC 26 W) or Equivalent in Bajaj/Philips/Crompton

Supply and Fix ventilating fan of size 250 mm sweep white in colour, plasitci body Type : Ventil air-DX WHT all as specified and as directed. Make: Havells or equivalent in Bajaj/ CG/ Usha

Taking down old unservicable ventilation fan ,Supply and fixing, ventilating Fan ( EXHAUST FAN) fans of 300 mm sweep, metallic range, single phase including necessary addn/altn for fixing of fans including makig hole on wal/windows all as per site requirement and making good the disturbed surfaces , matching with the existing wall all as specified and directed. . Make: Havells Ventil Air - DS or Equivalent USHA//C&G (Note:Old Unsv Exhaust Fans deposited to MES store yard)

M & L for Earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick burried directly in ground vertically to a depth of not less than 2.25 mtr below normal ground level with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised iron/steel earth wire 4 mm dia by means of bolts, nuts, washers and check nuts made out of galvanised iron, protected by GI pipe light grade 15 mm bore dia and connected to main control board all as shown in Electrical plate No 5 of MES SSR Part I including necessary excavation and earth work in any type of soil, salt, charcoad dust, PCC 1:2:4 type B1 in chamber, RCC 1:2:4 chamber cover with 6 mm dia MS bar at 100 mm centre to centre both ways and MS 6 mm dia hook complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out soft / loose soil for laying cables / pipes / erection of poles etc all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and as directed.

Returning filling in soil including spreading levelling watering well ramming in layers not exceeding 25 cm each all as directed.

Supplying and laying burnt brick "B" class standard size for cable cover all as specified and as directed.

Supply, lay, spread in trenches river and including spreading, levelling, punning for cushioning of cable all as directed.

Supply & lay LT UG cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100volts grade, cross-sectional area of following sizes all as specified and as directed.

4 core 16 sqmm Note :- 1. Lugs and glands are deemed to be included in the rate quoted for laying of cable and to be used properly whereever required while connecting cables to the panel board. 3. Earth work such excavation, refilling, etc. shall be measured separately under relevant items.

Supply & lay GI pipe light grade including necessary fittings of 40 mm bore all as specified and directed .

Supply and Laying of GI tubing medium grade 50mm bore with all fittings such as bends, sockets, elbows, tees, reducers, unions, sockets complete laid in trenches/ floors or fixed to walls all as specified.

Supply,install test and commission MONO block electrically driven pump set with brass impellar capable of pumping three phase, 5.0 HP (7.5 KW) capacity, (50x50 MM), 50M head, 1500 RPM, Mechanical seal,squirrel cage aircooled induction motor AC 415 Volt 3 phase 50 Hz of mounted on comman base plate including necessary PCC foundations works, bolts and nuts for fixing all as specified and directed by Engr in charge.Note:- (a)Common base frame for electric motor and pumping set-01 No (b) Suitable size of flanged valve Foundation for pumpsets is inclusive of quoted rate. MAKE Kirloskar/ equivalent Crompton Greeves /KSB.

Supply and fixing direct on line starter three phase suitable for 5.0 HP Pumpset in sheet metal enclosure complete acessories including single phase preventer all as specified.

M/S.RANGA AND CO

M/s C KESAVAN