Spl repair to toilet block of bldg No P-04, repair to bldg No T-96 OTM Accn and maint works at ECHS type A GSR under AGE B/R-I, GE Gurdaspur.

Amount

Dismantling of roof brick tiles fixed in cement mortar in single layer

Demolition mud phuska in roofs any thickness including plastering and leeping all as specified.

Roughening the surface of old concrete floor picking sweeping cleaning and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

Material & labour Cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in roof padding finishing the surfaces even and smooth without using extra cement complete all as specified.

M&L for applying evenly a tack coat of hot industrial bitumen 85/25 at the rate of 1.6 kg per sq.m on roof surfaces complete all as specified and as directed.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in, including bitumen primer @ 0.40 kg /Sqm after cleaning surface complete all as specified and directed.

M&L for 40 mm thick brick tiles laid over and including 15 mm thick cement mortar 1:6, joints grouted and flush pointed in cement mortar (1: 3) mixed with 5 % of crude oil by weight of cement, flush pointing in cement mortar (1:3) shall be done as a separate process, complete all as specified and directed

All as per Srl item No 07 above but except tiles

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, neelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating,complete all as specified & directed.

M&L for 75mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) in sub base complete all as specified & directed.

Demolition of cement concrete (unreinforced) of any description and in any position(above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed.

M&L plaster 15mm thick in cm 1:4 in sunken portion of slab with using waterproofing compound complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound

M&L for PCC 1:5:10 type E-2 using 40 mm graded stone aggregate as in filling foundation and mass concrete in sunken floor

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base complete all as spd.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for upto 12m ht. complete all as specified and directed by Engr-in charge.

Form work to rough finished surface of concrete flat to soffits of shelves, chajja, fins etc including supports, over hangs all as specified

S&F 6 to 8mm dia mild steel TMT bars cut to length bent to shape required including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips all as specified & directed.

S&F mild steel TMT bars 10mm dia & over, cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed.

All as per Srl item No. 20 above but but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for RCC 1:2:4 type B-1(using 20mm graded stone aggregate) as in chajjas facia, shelves etc and similar work all as spd.

M&L reinforced cement concrete (nominal mix) 1:2:4 ,Type B1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels complete all as specified & directed .

M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded stone aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by EIC.

M&L Non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 including demolition of existing complete all as specified.

All as per Srl item No 25 above but on vertical surface as in skirting over and including 10 mm thick screed bed in CM 1:3 complete all as specified.

M&L for ceramic glazed dark shed coloured tiles of size 350x250x7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in cm(1:4) set and jointed in neat cement slurry and pointed in coloured cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/dado including demolition of existing complete.

Demolition Stone slabs and tiles of any description or thickness in floors, aprons, counter platforms, etc. laid, bedded and pointed in cement mortar including backing

S&F udaipur green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, laid over and including 15mm thick cement screed bed in CM 1:4

Taking down cement plaster of any description on brick walls on concrete surfaces etc including raking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.

M&L for 15mm thick plaster in cement mortar 1:4 on fair faces of brick or concrete surfaces of walls, finished surface even and fair with WPC upto ht. 12 m complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

M&L 15mm thick cement plastering in cm 1:6 on other than fair faces of brick or concrete surfaces, finished the surfaces even and smooth without using extra cement as spd

M&L 12mm thick cement plastering in cm 1:6 on fair faces of brick or concrete surfaces, finished the surfaces even and smooth without using extra cement as spd

M&L for 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed.

M&L preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed.

M&L preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed.

M&L for Preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing surfaces and applying one coat of cement base paint on wall ht upto 12m complete all as specified and directed.

M & L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks, etc and applying one coat of white wash all as directed.

M & L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and applying two coats of white wash ht upto 12m all as directed.

M&L preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for Preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coat of oil bound distemper on wall complete all as specified and directed.

M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint ht upto 12m complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats and removing to store as spd

Taking down chowkats with shutter but exc 1.50sqm but n.exc 4 Sqm each (without taking off shutter for the chowkats and removing to store as spd

Taking down shutter exc 1.00sqm but not exceeding 2.00 sqm each, complete all as specified and directed.

Supply and fix for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of frames including one shop coat of red oxide primer and two coats of synthetic enamel paint and preparation of surfaces complete all as specified and as directed.

Supply and fix for pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary lugs, hinges, lock strike plate, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of frames including one shop coat of red oxide primer and two coats of synthetic enamel paint and preparation of surfaces complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 25mm thick factory made Flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides, both faces covered with decorative face veneer as in cupboard shutters, shelves and partitions with 2nd class hard wood lipping/frame to match complete all as specified and directed.

S&F 35mm thick second class hard wood (Hollock), glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) supplied and fitted to chowkats complete all as specified and directed.

S&F Aluminium anodized barrel tower bolt of extruded section 150mm long complete all as specified and directed.

S&F Aluminium anodized barrel tower bolt of extruded section 100mm long complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed.

S&F100mm size medium weight mild steel butt hinge fixed with metal surface through bolt or screw of welding complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy, type B-21 with galvanised mild steel hinge pin, anodised fixed with metal surface through bolts or with screws complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F in repair 300 mm long mild steel ordinary rat tail rod pattern spring, including roller and roller plate including fixing through welding/ bolts/ screws in metal/ wooden frame complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and fixing curtain rod 20mm dia of anodised aluminium alloys with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of red oxide primer and two coats of synthetic enamel paint and taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of red oxide primer and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately

M&L for preparation of new wooden surface exc. 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide xince chrome primier complete all as specified & directed .

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frame, glazed with putty and fixed with beads.

S&F sheet glass 3mm thick ordinary quality, fixed with oil putty in square n exe 0.5sq m in each pane

S&F sheet glass 4mm thick ordinary quality, fixed with oil putty in square n exe 0.5sq m in each pane

S&F Figured glass pin head type glazing with oil puty glass 3mm thick, fixed with oil puty in square n exe 0.5sq m in each pane.

Re-fixing old steel tubing including new fittings 15mm bore in new or old position including taking up and down, cleaning the same complete all as specified and directed.

Re-fixing old steel tubing including new fittings 20mm bore in new or old position including taking up and down, cleaning the same complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Taking up and down GI pipe15mm bore including fittings, connection, as spd

Taking up and down GI pipe 20mm bore including fittings, connection, as spd

S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc. with all fittings ISI marked all as spd

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked all as spd

S&F GI tubing 32mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up or down old pipe complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition including 20mm ball brass valve, high pressure, with polythene float and flynut and connected fittings including demolition of water tanks complete all as specified and directed.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition including 20mm ball brass valve, high pressure, with polythene float and flynut and connected fittings including demolition of water tanks complete all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc all as spd

S&F in repair 15mm dia CP bib tap cast copper alloy fancy type, with capston head screwed down, for iron pipe and fixed.

S&F in repair for 15mm bore Stop valves/ Angle valves, but fancy type, chromium plated cast copper alloy, screwed down, high pressure, handle, screwed both ends for iron pipe or for unions.

S&F in repair brass CP shower rose 125mm size with swivel joint fancy type as spd

S&F in repair alumunium anodised towel rail 20mm dia. `D’ type 60 cm long between flanges fixed to wall all as spd and directed.

S&F in repair Pillar taps, cast copper alloy but fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repairs 08 to 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle, 32mm dia PVC flush pipe and connections, joints to pipes, complete all as specified and as directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete complete all as specified Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F in repair for Vitreous China wash down water closet pan (pedestal pattern) white (excluding flushing cistern and flush pipe) including plastic water closet seat white, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device with brass CP jet complete all as specified and directed.

S&F in repair vitreous China half stall type urinal, of size 345x320x560mm, white, with brass CP spreader including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement paste, 32mm dia PVC flush pipe and discharge pipe, grating and union for discharge pipe, waste coupling of PTMT (half or full threaded) bore dia of discharge pipe 32mm (Minimum weight 45gms) complete all as specified and as directed.

S&F in repair Vitreous china counter top oval wash basin, snow white, size 560x400x205mm, including 32mm size cast copper alloy CP waste coupling and 32mm bore PVC waste pipe complete all as specified and directed. Make: Cera or equivalent as per Appx 'B'.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or floor all as specified & directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor complete all as specified.

S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.

S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.

S & F in repair 110 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal), with oval access door complete all as specified and directed.

S & F in repair 75 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal), with oval access door complete all as specified and directed.

S&F in repair PVC (SWR ) vent cowl 110 mm bore

S&F in repair PVC (SWR ) vent cowl 75 mm bore

M&L in repair PVC (SWR ) floor trap 75 mm plain with MS grating incl. jointing with solvent cement

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F Stack clamps (75 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Cutting openings through Old masonry walls built in cement mortar walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, and removing rubbish off the premises complete all as specified & directed.

Demolition of brick work, built in cement mortar or cement lime mortar including all quoins, pillars etc. complete all as directed.

M&L for brick work with flyash old size bricks straight or curved on plan exc. 6m mean radius built in CM 1:6 brick all as spd.

All as per Srl item No 112 above but except bricks

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for removing existing pointing & Flush pointing to bricks laid flat or brick tiles in pavings and pointing with CM (1:3) complete all as specified and directed by Engineer-in-Charge.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in at any height complete all as specified. Note: - Cost of formwork and welded mesh, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

M&L for taking down wooden roof trusses, coupled rafters or trussed beams, for clear span above 4m & upto 8m

Demolition timber scantlings 40 sq. cm and over in section, in any position, unframed work

Demolition wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets/ grid, any description, fixed in any position.

M&L 100 mm thick cement concrete 1:4:8 type D-2 (uising 40 mm graded stone aggregate) as in sub base etc complete all as specified & directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the floor over and including 20 mm thick screed bed in CM (1:4) including rubbing and Bees-wax polishing on surfaces of any description, width or girth including cleaning and preparing the surface complete .

M&L Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade over and including10mm thick rendering in CM (1:4) including rubbing and Bees-wax polishing complete

S&F Makrana white marble work 18-20mm thick machine cut in floors bedded jointed and pointed with grey cement slurry over 20mm screed bed in cement mortar (1:6) including cutting and polishing complete all as specified and as directed.

S&F Makrana white marble work 18-20mm thick machine cut, bedded jointed and pointed with grey cement slurry on vertical surface over and including 10mm thick rendering in CM (1:4) including cutting and polishing complete all as specified and as directed.

Demolition of asbestos cement corrugated or semi corrugated sheets in roof covering of any gauge and thickness complete all as specified and directed.

Dismantling of steel sheeting corrugated or semi corrugated sheets in roof covering of any gauge and thickness complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

All as per Srl item No 127 above but except sheet

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 or using hollow mild steel sections of square or rectangular tubes conforming to IS: 4923-1997 gradegrade St.-240

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410-W Gde E-250 Quality A

M&L Mild steel rag or lewis bolts, screwed one end,with hexagonal or squarenuts and washers, the other end enlarged and jagged or lewised, exc 30cm long and diameter of neck 20mm complete all as specified & directed by Engr-in-Charge.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L Non asbestos fibre cement building boards 4mm thick in ceiling flat or sloping, fixed or laid/ inserted to timber/GI/Aluminium framework with screws

S&F GI powder coated snap grid frame work of size 605mm X 605mm, with main tee of size 32mm X 23.5mm x 1.5mm thick, cross tee of size 25mm X 23.5mm x 1.28mm and angle of size 23.5mm X 23.5mm x 1.2mm fixed on wall, all as specified complete all as specified & directed. (suspension wire for measuring fixing snap grid measured and paid under separately)

Supply only Galvanised mild steel plain wire dia not less than 3.15mm for hanging purpose of ceilling frame complete all as specified & directed by Engr-in-Charge.

Surface dressing n exc 15 cm deep in soft /loose soil

M&L 25mm thick sand cushioning under floors including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Material and labour for Machine pressed precast concrete interlocking paver block coloured any shape and size confirming to IS:15658-2006 of 80mm thickness, M-40 Grade using grey cement & pigment complete all as specified and directed

Material and labour PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed by Engineer in Charge.

Material and labour Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed by Engineer in Charge.

M&L for preparation of new surfaces and applying two coats of Synthetic enamel paint on kerb stone of any description over 10cm girth or width, not otherwise described complete all as specified and directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5m as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished even and fair.

S&F fibre glass reinforced translucent corrugated sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket with complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

Point wiring with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm (nominal area) using approved colour coding, 1100 volts grade, ISI marked, including PVC conduit heavy grade, 20 mm or higher dia. with fittings concealed in wall/ on surface for ceiling with continuous earth wire of PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm (nominal area) 1100 volts grade, ISI marked and connecting to the common earth dolly including provn of 3mm thick plastic laminated sheet of appropriate size and sunken CI/pressed steel terminal boxes for mounting switches, sockets and regulators etc. including cutting chases and making good to the disturbed surfaces as per existing for One light point/fan point/ bell point controlled by one, one way switch complete all as specified and directed.

All as per Srl item No 147 above but one 5 pin socket outlet 5/6 amps on same board.

All as per Srl item No 147 above but 5/6 amps socket outlet on independent board.

All as per srl item No. 147 here-in-before but with multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area) with continuous earth wire multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area) for 3 pin 15/16 Amps socket outlet on independent board.

M&L for sub main wiring with two single core multi stranded PVC insulated, copper conductor of grade 1100 Volt , FRLS cable of size 6 sqmm (red for phase and black for neutral) and including electrical grade PVC conduits of desired colour not less than 1.2 mm thick and 25 mm dia. & 6 sqmm FRLS multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth duly complete and taking down old unserviceable one. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing finish is deemed to be included in the rate quoted by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5/6 amps.

S&F socket outlet 3 pin 5/6 amps flush type.

S&F switch flush type 15/16 amps single pole type one way

S&F socket outlet 3 pin 15/16 amps flush type

S&F in replacement surface mounting universal batten husing made of powder coated CRCA sheet suitabe for and upto 1 x 18/20W LED tube rod single sided complete all as specified and directed.

S&F in replacement LED tube light 20W ultra bright LED polycarbonate tube light with very high efficacy suitable for fitting into tube light batten fitting complete all as as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report from manufacturer to Engineer-in-Charge before incorporating the items in work.

Supply and fix for lamp holder angle type, PVC/ polycarbonate type with back plate, suitable for lamp holder base of and including 9 watt LED retrofit lamp complete all as specified and as directed.

M&L ceiling rose, 3 terminals/ phase/ PVC/ polycarbonate, isolated body

S&F in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as specified and directed.

Supply and fixed in repair sheet metal enclosure for DB’s when MCB’s to be used, 240 volt 8 way SPN with bus bar and double door complete all as specified and directed. Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed

S&F in repair MCB single pole 6 amps to 32 amps complete all as specified and directed.

S&F in repair MCB single pole and neutral 32 amps, complete all as specified and directed.

S&F GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 40mm x 5mm thick and drilling of hole for and including nuts, bolts and washers including painting MS clamps with two coats of synthetic enemal paint over a coat of red oxide primer including taking down the existing GI pipe bracket complete all as specified and directed.

S&F in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including taking down existing fitting complete.

Supply and fix exhaust fan, steel body AC single Phase 230V of size 300mm sweep with blades and frame and louvers complete all as specified and directed.

A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

J S MAAN ENTERPRISES

KAILASH CONSTRUCTION CO