86165 ADDN / ALTN AND SPECIAL REPAIRS TO BLDG NO. P-14 AT LOWER COMMAND HOSPITAL AND SPECIAL REPAIRS TO IH AND BT DEPT AT AFMC UNDER GE (CENTRAL) PUNE

Amount

Dismantling stone slabs/tiles of any description or thickness laid bedded & pointed in cement mortar in floors, hard standing, Apron etc. complete all as specified and as directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, (Posts embedded in concrete or natural ground) including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Dismantling fencing wire mesh any type complete all as specified and directed.

M&L for 40mm thick levelling course/ subbase/ in floor in cement concrete 1:2:4, type B-1 using 20mm crushed stone graded aggregate complete all as specified and as directed.

Material and labour for Non skid ceramic tiles coloured, 7 to 8 mm thick (Square / rectangular) area of each tile exceeding 0.06 Sqm but not exc 0.11 Sqm, over & including 15mm thick screed bed in CM (1:6) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles as directed and specified.

M&L for 300x600x6 to 7mm thick, joint free coloured, glazed ceramic tiles as in skirting/Dado, laid and jointed in neat cement slurry and pointed in coloured cement to match complete over and including 10mm thick backing coat in CM 1:4 including triangular filleting on top in CM 1:3 complete all as specified and directed.

M&L for 20 to 25mm thick machine cut Kota stone (550 x 550 mm) flooring over cement screed base laid and jointed with grey cement slurrry mixed with pigments to match the shade of the slab including rubbing and polishing upto entire satisfaction of Engineer-in-Charge complete all as specified over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

All as per Ser. item 08.00 above but kota stone slab (100/150mm x 550mm) and 20-25mm thick in riser of steps, skirting , dados and pillars polished to entire satisfaction of Engineer-in-Charge laid over and including 10mm thick rendering to receive the stone in cement mortar 1:3 and jointed complete

Material and labour for Chequered cement concrete tiles 25 Cm x 25 Cm x 25mm thick over and including 15mm thick screed bed in CM 1:6, set, jointed with grey cement and pigments and pointed in neat cement slurry in floors complete all as directed and specified.

M & L for granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking/working platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed and specified.

Rounding to edges of stone slabs on edges, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Demolition of brick/precast block walling built in cement mortar complete all as specified and directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified & directed by Engr-in-Charge.

Taking down cement plaster on brick/ block walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Rendering 15mm thick in CM (1:4) on fair faces of PCC block/brick walling, using liquid water proofing admixture @ 200 ml per bag of cement and surface finished with sponge finish complete all as specified and as directed. (Note : WPA shall be measured and paid separately)

Supply only liquid water proofing admixture complete all as specified and directed.

Rendering 10mm thick in CM 1:6, on brick/ PCC block walling, finished even & smooth with a thin layer of sagol finish complete all as specified and as directed.

M&L for preparation of newly plastered surface and using sand paper to have even and smooth surface and applying two coats of weather coat paint (Weather coat Exterior emulsion) white or tinted over a coat of white water base primer complete all as specified and directed by Engr in charge.

M&L for Preparation of new plastered surfaces and applying two coats of cement base paint over alkali resistance primer complete all as specified and as directed.

M&L for Preparation of new plastered surface and apply two coat of oil bound distemper over 1-2 mm thick wall care putty complete all as specified and as directed.

Taking down chowkats or frames of wooden or steel exc 1.5 sqm & not exc. 4 Sqm (without taking off shutters from the frames) complete all as directed and specified.

Taking down chowkats or frames with shutters not exceeding 1.5Sqm (without taking off shutters from the frames) complete all as specified and as directed.

S & F Anodised aluminium frame powder coated (min thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed

S&F Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium alloy handles 2 Nos of 150mm long in each door, hinges (03 Nos 100mm long), anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F three track sliding window with two or more shutter with 4 mm thick tinted glass , one shutter of stainless steel wire cloth 0.56 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle lock, rubber beading and glazing clips etc using following aluminium powder coated sections confroming to catalogue of 'JINDAL' or of equivalent make complete all as specified directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & Verrtical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & Bottom 20844 (f) Glazing Clip 19352

S&F ventillators/ louvers with partially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading and all necessary fittings as required etc all as directed. (a) SP 20048 (b) Glazing clips 19352

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube complete all as specified and as directed

S&F factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made out of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing as per product Drg given on Sl. Page No. 176 of SSR Part-II 2020 Refer item No. 8080 as specified and directed by Engr-in-charge.

Supply and fix stainless steel butt hinges 100mm size and fixed complete all as specified and as directed.

S & F 300mm aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clip of steel cast or extruded section with fixing bolt and sliding bolt of extracted section or cast aluminium alloy

Supply and Fix Aluminium anodised barrel tower bolts of extruded section, 150mm long complete all as specified and as directed.

Supply and Fix Extruded aluminium alloy handles fabricated type anodised 150 mm size complete all as specified and as directed.

S & F in repair figured glass pin head type, 3mm thick and glazing with oil putty in square n.exc. 0.50 Sqcm in each pane complete all as specified and as directed.

M & L for 75 mm thick cement concrete 1:3:6, type C2, using 40 mm graded crushed stone aggregate in plinth protection, finish the surface even and smooth without using extra cement including filling the expansion joints with bitumen filler/filler boards complete as specified and directed.

M & L for 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

Hacking out old broken glasses of any thickness size & quality from wooden or steel window glazed with putty or fixed with beads including punching or drilling out old glazing pins/clips etc complete all as specified and as directed.

S & F 3mm thick glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling of Single layer Mangalore pattern or similar tiles in roofing complete all as specified and directed.

Dismantling of timber scantlings 40 sqcm and over in section, in any position of framed work complete all as specified and directed.

Dismantling of timber scantlings as in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section in un-framed work complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

M&L for second class hard wood clean swan in scantling in any position of framed work complete all as specified and directed.

M&L for 2nd class hardwood Plain fillets exc 6 and n exc 13 sqcm in square, rectangular or triangular in section, clean sawn, secured with nails or boards as in fillets, rails, posts, rafters, purlins etc complete all as specified and as directed.

S&F IInd class hard wood 20mm thick boarding fixed with nails in any situation planed one side with butt joints complete all as specified and directed.

S&F Roof tiles, Mangalore pattern, interlocking at side joints, laid dry in roofing complete all as specified and directed.

Fixing only roof tiles, Mangalore pattern, interlocking at side joints, laid dry in roofing complete all as specified and directed.

M&L for Ridge or hip tiles to suit Mangalore pattern roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and directed.

S & F, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts of 0.80 mm thick, complete all as specified.

S&F 0.50 thick (total coated thickness) pre-colour, pre-profiled (Galvalume/Zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof, wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer/profile maker instruction complete all as specified and directed.

S & F pre - painted galvalume aluminium zinc coating GI based plain steel sheeting 0.5 mm thick of required colour and shape having tensile strength of 550 Mpa as in ridge valley,gutters,bridge board,roof covering / cladding to wall, fixed with self tapping screwes complete all as specified and directed.

Supply and fix hollow steel section as in trusses, main and cross beams, hip and jack rafters; purlins where connected to common rafter and running rails and guides for sliding door fixed with angle cleat or other connecting plates etc complete conforming to IS-4923-1997 of FE 410-W (Gde-E-250) quality A complete all as specified and as directed

Taking up or down carefully steel tubing and connections including cleaning for refixing complete all as specified and directed of following sizes :-

15mm bore

20mm bore

25mm bore

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) incld cutting chases, pinning in brick/concrete surfaces and making good to facings where required and pointing in cement mortar 1:3 complete all as specified and as directed of the following sizes :-

15mm bore

20mm bore

25mm bore

S&F GI tubing tubes "medium grade" galvanized with all fittings and fixed complete to walls and ceiling or laid in floors etc incld cutting chases, pinning in brick/concrete surfaces and making good to facings where required and pointing in cement mortar 1:3 complete all as specified and directed of the following sizes :-

15mm bore

20mm bore

25mm bore

S & F in repairs stop valves 15mm bore of brass cast copper alloy, screwed down , high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F in repair 15mm bore Angle Valve fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs CP health faucet with flexible pipe fancy type complete all as specified and directed.

S&F in repairs PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor/wall complete all as specified & directed of following sizes :-

110mm bore

75mm bore

S&F in repairs PVC (SWR) bends any radius 75mm bore complete all as specified and as directed.

S&F in repairs PVC (SWR) bends any radius 110mm bore complete all as specified and as directed.

Supply and Fix in repairs vitreous china Wash hand basin flat back, size 630x450mm white excluding pillar taps & waste pipe but including Waste coupling PTMT and fixing brackets complete

Supply and Fix in repairs Pillar tap 15mm bore, cast copper alloy,with capstan heads, chromium plated, screwed down, high pressure with long shanks and fly nuts, screwed for iron pipe complete.

Supply and Fix in repairs vitreous china bowl urinal (Top inlet), with fixing accessories full stall type, including PVC down waste pipe, fixing plugs etc and fix to walls and connect to existing flush systems complete as directed and specified

S&F in repairs vitreous china wash down water closet pan, 'Pedestal', white , including fixing bolts etc including PVC seat cover white with flat bottom including CP or aluminium anodised hinges devices etc complete all as specified and directed.

S & F in repairs fancy type chromium plated two way bib tap fancy type, cast copper alloy with crutch or butterfly handle ,incl wall flange, screwed down,screwed for iron pipe 15 mm bore or brass ferrule complete all as specified and directed at site.Make Jaquar or equivalent

S & F in repairs fancy type chromium plated bib tap, cast copper alloy with crutch or butter fly handle ,incl wall flange, screwed down,screwed for iron pipe 15 mm bore or brass ferrule complete all as specified and directed at site.

S&F in repair 600mm long stainless steel towel rail at site complete all as specified and directed.

S & fix in repairs syphonic action PVC low level flushing cistern of 10 ltr capacity including internal fittings, brackets,32mm flush pipe etc, complete all as specified and as directed.

Supply and Fix in repairs Stainless steel grating dome 125mm dia with or without waste holes as required complete all as specified and as directed.

M&L for 100mm Cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F aluminium powder coated fancy type curtain rod 20mm bore complete all as specified and directed by Engr-in-Charge.

S & F aluminium powder coated brackets suitable for 20mm bore curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed by Engineer-in-Charge.

Dismantling aluminium partition of any description complete all as specified and as directed

S&F aluminum powder coated partition Pattern approved by GE using Jindal or equivalent Catalogue Sections DP/SP weight not less than 1.0 kg/RM with frosted glass 5 mm thick and 12 mm thick prelaminiated particle board (both side laminated) fixed with glazing clips, Jointing cleats, rubber gasket, neoprene packing, anodised aluminium snap beading screws complete all as specifed and directed

S&F powder coated Aluminium grill 6.5mm thick of pattern DG 014 or equivalent surrounding by F-channel of 1.2mm thick fixed to 'Y' or 'C' section aluminium window complete all as specified and as directed.

S&F MS framed work as in grill, doors or gates of angle iron, door frame or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering etc. to prepared for hanging or sliding with including either hooks and hinges, also fastening and fixing and similar work confirming to Fe 290 Gde-E-165 complete all as specified and directed.

Taking down Aluminium Door shutters of any size, carry out minor repairs with & including replacement of unserviceable top/bottom rail, hinges, rubber beading, etc and also carry out repalcement of broken wire mesh and glass panes wherever necessary incl. 6mm dia MS studs at top and bottom rail complete (wire mesh and glass pane shall be measured and paid separatly) and refixing the shutter in the same opening complete as directed and specified.

All as per Ser. item No 81.00 above but Aluminium window shutters of any size complete all as specified and as directed.

S & F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.4 mm and fixed with stainless steel wire staples complete all as specified and as directed.

M&L for preparation of old decorative surfaces of ceiling incl, cornices (plastered or unplastered) by brooming down and scrapping wherever necessary and applying two coats of oil distemper emulsion on ceiling complete all as specified and as directed.

Complete removal of existing treatment by mechanical means and applying 3 mm thick wall care putty and applying two coats of distemper oil emulsion on walls all as spd and directed.

Complete removal of existing treatment by mechanical means and applying Two coats of weather proof exterior acrylic emulsion paint (1st Quality) of required shade (Company Depot Tinted) with silicon additives, over and including priming coat of exterior primer on surfaces of walls complete all as specified and directed. [Note :- (a) Height of Bldg : any height (b) Exterior acrylic emulsion paint shall be anit-fungal, dust resistant, water repellant, crack-bridging, weather proof type 1st Quality. (c) Applicator should be from approved company and Guarantee Certificate required for 5 years.]

M&L for Preparation of old painted wooden surfaces of any descrition exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for Preparation of old painted steel surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint on new or previously untreated steel surfaces exc 10cm width or girth over a coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and as directed.

S&F Welded steel wire fabric not exc 4 Kg/Sqm to wood or steel members complete all as specified and as directed by Engr-in-Charge

Resecuring or easing & adjusting without taking down shutter of any description not exc 1 sqm each in the same opening as directed and specified.

All as per Ser item No. 91.00 above but exceeding 1 sqm and not exc 2 sqm each complete all as specified and as directed.

Removing of existing old bitumenous tarfelt (water proofing treatment) including cement screed bed, bedding PCC of any thickness and clean the surface with wire brush and washing with water to achieve the original surface of slab complete all as specified and as directed.

M&L for 25mm thick roof padding in cement concrete 1:2:4 type B-0 using 12.5mm crushed stone graded aggregate, mixed with liquid water proofing admixture @ 200ml per bag of cement, finishing cement concrete surface even and smooth using extra cement complete all as specified an as directed. (Note : To be operated for roof padding, liquid waterproofing admixture type will be measured and paid separately)

M & L for water proofing treatment to RCC roof slab, walls, chajjas etc, shall be carried out as specified below and as directed by Engr-in-charge (a) M & L for 10 mm thick plaster screed bed layer in CM 1:3 on concrete surfaces mixed liquid water proofing admixture @ 200 ml per bag. (b) Preparing plastered surfaces of roof slab, walls, chajjas etc, by brooming with broom sweeping free from dirt / dust etc and applying one coat of oil based cold bituminous primer @ 0.40 litres per Sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane, non woven, polyster, weighing not less than 3.5 Kg/Sqm and 3 mm thick with laps and overlaps as specified and joints sealed and applied complete by torch application method all as specified and directed by Engr-in-charge, Carrying out test by ponding water for 24 hrs for leakage and seepage and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified and as directed by Engr-in-charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as sepcified and as directed

S&F in true horizontal level 595x595x8mm false ceiling non asbestos decorative tiles including GI snap grid of size (600x600)mm, using hot dipped galvanised steel section, exposed surface with pre-coated capping, main tee of size 24 x 38mm having 0.27mm gauge at every 1200mm, centre to centre maximum and rotary stitched cross tee of size 24x 32mm, having 0.25mm gauge at 1200mm c/c. Wall angle of size 19x 19mm, having 0.35mm gauge fixed to the periphery of the wall. The above grid is suspended at every 1200 mm c/c in both directions using 2.0 mm thick pre-straightened GI wire. The board to be finished with two coat of OBD over coat of primer to all side all as specified and directed.

Labour only for Grinding, rubbing and Polishing to existing kota stone flooring/ terrazo tile/ terrazo cast in situ incl filling of joints where required upto entire satisfaction of Engineer-in-Charge and complete as directed

Surface Excavation not exceeding 30 Cm deep and averaging 15 cm deep and getting out in Soft/ Loose soil complete all as specified and as directed.

M & L for hard core of broken stone or boulder having gauge not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thk, watered and rammed to a true surface, complete all as specified and as directed.

M & L for 75mm thick Plain Cement Concrete 1:4:8 Type D2 (using 40 mm graded crushed stone aggregate) as in sub-base complete all as specified and as directed.

M & L for 30mm thick sand cushioning/sand filling under pavement incl watering, consolidationg with clean dry sand , complete all as specified and as directed.

M&L for laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern, glossy finish as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for providing Precast cement concrete in type B1 1:2:4 (20 mm crushed stone graded agg) in kerbs and edging to road and footpath etc. (i.e 80 mm thick and 45 cm to 60 cm long/ height) finished at top bull nosed shape and finished even and smooth using coloured pigment incl necessary earthwork with plain fair faces, incl chamfered wheathering, throating etc and setting in mortar 1:4 complete with joints to match all as specified and as directed

Excavation in trenches not exc 1.5m depth for foundation etc. and getting out in hard / dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soil complete all as specified and as directed.

Removing excavated material exc. 250m but not exc 500m and depositing where directed complete all as specified and as directed.

M&L for Plain Cement Concrete 1:3:6 Type C2 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations, footings, base of columns for rough finished flat surface of concrete, complete all as specified and as directed

Use and waste for fair finished square, rectangular or polygonal formwork to sides of pillars posts, struts, columns and stanchions etc complete all as specified and as directed

M&L for RCC (Nominal mix) 1:2:4 type B1, using 20mm graded crushed stone aggr as in columns, piers, posts and struts complete all as specified and as directed

M & L for TMT bars 10mm dia and over cut to length bent to shape required incl, cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to IS:1786 complete all as specified and as directed

M & L for TMT bars but 8mm dia and over and including 10mm dia in stirrups, spacers and binders and binding with MS wire not less than 0.9mm dia (annealed) conforming to IS:1786, complete all as specified and as directed.

Excavating in post holes (or similar holes) each in hard/ dense soil not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed

S & F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only chain link MS galvanisd fencing of size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

M&L for double charged vitrified ceramic tiles (dark shade) 10mm thick (square /rectangular) polished, area of each tiles exceeding 0.42 sqm but n exc 1.00 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to the match the tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M & L for solid block masonary exc. 10 cm width blocks of PCC design mix Gde C-5 set in CM (1:6) complete all as specified & directed by Engr-in-Charge.

S&F Machine cut 20-25mm thick cuddappah stone slab over 20mm thick cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over platform/shelves all as specified and as directed

M&L for 20mm thick granite (of any type) work table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed layer in CM 1:3 as in floor / skirting / risers or as in vertical support with edges polished / rounded or counter top for wash basin as ordered incuding cutting circular or eliptical hole in granite slab and fixing in position complete and ensure best adhesion to surface complete

S&F in repair Vitreous china wash hand basin/sink of size 660x460x200mm including rim for lab conforming to Cat Part No. S6010102 of Cera or of equivalent make specified here-in-after complete with all fittings accessories complete all as specified and as directed.

S&F in repair self closing swan neck chromium plated pillar tap of 15mm bore fancy type with all accessories complete all as specified and as directed

S&F factory made PVC cupboard frame of the size 75mm x 40mm with a wall thickness of 4mm made out of extruded 4mm thick plain/prelam inated PVC sheet reinforced with 15x15mm MS square tube of 19 gauge thickness throughout the frame and mitred cut at two corner adjointed with 2 Nos of 150mm long brackets of 10mm x10mm MS square tube. The door frame shall be fixed to the wall using 65/100mm MS screws through the frame by using PVC fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum of 02 Nos of screws to be provided horizontal member etc complete all as specified and directed by Engr-in-charge

S&F PVC cupboard shutter of 18mm thick consisting of frame made out of MS tubes of 16 gauge thickness and size 10mm x10mm covered with 4mm thick PVC 'C' channel of size 18mmx50mm forming stiles, top and bottom rails. Panelling of 4mm thick prelam PVC sheet, fitted in MS frame and sealed to the front stiles and rails (which should have 6mm (4mm+2mm)x30mm wide strip) and attached to back of stiles and rails (which should have a 4mm 45 degree bent portion as beading) and 10mm decorative PVC beading is used on the front side of panel externally impact perfect finish to the shutter and jointed together with solvent cement adhesive and 8mm thick (4mmx2)x12mm wide PVC sheet is used as gap insert for top & bottom rail, 18mm x 1mm PVC edge lipping is done on top & bottom side and additional of 4mm thick PVC strip of 12mm width is to be stuck on the interior side of the 'C' channel using PVC solvent cement adhesive etc complete as specified as per manufacturer's instrs and as directed by Engr-in-Charge with fxing accessories like autocado steel hinges (02 Nos) in each shutter, magetic door catcher and SS handle (01 Nos) in each shutter

S&F in repair ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F Autocado steel hinges, soft closing type for cupboard complete all as specified and as directed.

Supply and Fix Extruded aluminium alloy handles fabricated type anodised 100 mm size complete all as specified and as directed.

S&F Hasp and staple safety type aluminum with mild steel hinge pin including bolt to hinge plate and fixed with screws of 100mm size complete all as specified and as directed.

S&F 32mm dia Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe as in WHB/Sinks/urinals etc complete all as specified and as directed

Taking down old unserviceable point wiring( light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants,regulators sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified. [Note :- (i) Credit for above items should be made as per conditions separately) (ii) Temporary arrangement for providing electric supply to be given by the contractor without any extra cost to the Dept of IH & BT for certain equipments at the time of carrying out work as they run a 24 Hours blood bank and the functioning of the blood bank cannot be stopped completely during the period of work. (iii) Rooms will be handed over for carrying out work in Phased manner as mentioned in PS.]

Taking down old unserviceable/worn out sub main wiring / service wire of any type and size complete all as specified and as directed.

Taking down Distribution boards alongwith MCBs / MCCBs and Industrial sockets etc complete and making good the disturbed surfaces complete all as specified and as directed.

Taking down ceiling fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of suitable size from ceiling rose to fan terminal, cleaning, servicing and overhauling the ceiling fans including lubricating, greasing, replace the bearing, replace the condensor of suitable size, Painting of fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and fitted the fan in servicable conditions complete all as specified.

Removing of LT Cable of any size from wall, ceiling, roofs, floors etc, keeping with safe custody and refixing the same with replacement of lugs, thimbles, glands, insulation sleeves, saddles, etc from LT Panel to DBs laid in working conditions complete all as specified. [Note for Item No to :- (i) Temporary arrangement for providing electric supply to be given by the contractor without any extra cost to the Dept of IH & BT for certain equipments at the time of carrying out work as they run a 24 Hours blood bank and the functioning of the blood bank cannot be stopped completely during the period of work. (ii) Rooms will be handed over for carrying out work in Phased manner as mentioned in PS.]

M&L for point wiring complete with and including single core FRLSH PVC insulated un-sheathed flexible bright annealed multi stranded copper conductor cables 1.5 sqmm 1100 Volts grade drawn through and including heavy grade Cap and casing of suitable size or higher dia as required at site surface in walls /floors/ceiling/roofs etc. including all accessories/ fittings/ junction boxes/inspection covers etc. of heavy grade, ISI marked and modular PVC type sunken boxes and plates (inside & outside) factory made including 1.5 sqmm 1100 V grade FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cable as continuous earth wire connected to metallic bodies of luminaires/fans etc. at one end to common earth dolly at other end, complete all the specified.

One light/fan point controlled by one, One-way switch complete all as specified

One 5 pin 5 Amp Socket outlet point on same board complete all the specified.

One 5 pin 5 Amp Socket outlet point on independent board complete all the specified.

One bell/buzer point controlled by one bell push complete all as specified.

One light point controlled by two 2-way switches complete all as specified.

All as per Item No. 136.00 above but with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent board, including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly complete all the specified.

S&F Modular Switch flush type, single pole, one way, 6/10 Amp complete all as specified and as directed.

S&F Modular Switch flush type, single pole, one way, 16 Amp complete all as specified and as directed.

S & F Modular Socket outlet 3 pin, 5A, flush type, multipurpose 230 Volts, single pole one way complete all the specified

S&F Modular Socket outlet 5 in 1, 3 pin, 5 and 15 Amp flush type universal, 240 volts, ISI marked complete all the specified

S & F Ceiling fan regulator electronic, step type suitable for ceiling fan 1200 mm sweep 230 Volts single phase AC complete all the specified

S&F ceiling rose surface type three terminals complete all as specified and as directed.

S&F sheet metal enclosures single pole and neutral enclosure with a three pin and earth plug and socket with one MCB SP 20/ 32 Amps complete all as specified and as directed.

S & F of LED light fittings 2'x2' of capacity 36 watts environmental friendly, new genereation, aesthetically designed, ultra modern recess mounting luminaire with high power LEDs as light source 230 volts with all accessories internally pre wired and necessary mounting arrangements complete all as specified. (Make :- Bajaj Cat part No. BZSSQL 36W LED G54 WH or equivalent approved make)

Supply and fix in replacement LED Tube light fittings wall/Ceiling mounted, 18/20 W LED 6500K with Ultra bright LED Polycarbonate Tube-light with very high efficiency provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size from ceiling rose to connector complete all as specified and as directed.

Supply and fix in replacement Focus light fittings wall/Ceiling mounted, 3/5 W LED adjustable type Ultra bright very high efficiency provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 4 sqmm including PVC rigid conduit of suitable size and accessories complete all as specified and as directed. [Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 4 Sqmm conductor and one run of PVC conduit shall be measured as one unit length.]

M & L for Sub main wiring complete with two single core 6 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 6 sqmm including PVC rigid conduit of suitable size and accessories complete all as specified and as directed. [Note :- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 6 Sqmm conductor and one run of PVC conduit shall be measured as one unit length.]

S&F Sub main wiring complete with four single core 6 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 6 sqmm including PVC rigid conduit of suitable size and accessories complete all as specified. [Note : - (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 5 runs of 6 Sqmm conductor and one run of PVC conduit shall be measured as one unit length.]

S&F Sub main wiring complete with four single core 10 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 10 sqmm including PVC rigid conduit of suitable size and accessories complete all as specified. [Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 5 runs of 10 Sqmm conductor and one run of PVC conduit shall be measured as one unit length.]

S&F vertical type double door TPN DB 12 way IP 43 recess mounted/ wall mounted type alongwith locking arrangement with including incoming MCCB 3 Pole 25 KA 160/200 Amps and outgoing MCB TPN 63/40 Amps and MCB SP 40 Amps suitable for single phase/three phase out going supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary or surface recessed mounted etc and making good of distrubed surface to match with existing colour of wall complete all as directed

S & F Manual onload changeover switch in sheet steel enclosure of rating 200A 4 Pole 415 Volt all as per manufacturer design complete all as specified and as directed.

S&F MCB TPN DB 4 way, double door, with 200 amp rated busbar 415 V complete all as specified and as directed.

S&F MCB DB 12 way, double door, with 200 amp rated busbar 240 V, complete all as specified and as directed.

S&F MCB DB 8 way, double door, with 200 amp rated busbar 240 V, complete all the specified

S&F MCB DB 4 way, double door, with 200 amp rated busbar 240 V, complete all as specified and as directed.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN 63 Amps and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and as directed.

S & F for MCB SPN of rated capacity 40-63 Amps, 240 volts breaking capacity 10 KA, B-curve installed in existing distribution board complete all as specified and as directed.

S & F for MCB SP of rated capacity 40 Amps, 240 volts breaking capacity 10 KA, B-curve installed in existing distribution board complete all as specified and as directed.

Labour only for removing/reinstallation of Split type ACs and window type ACs 1.5/2TR cap alongwith stabilizer, indoor & outdoor unit including all allied work such as filling of refrigerant, bending, shaping, brazing to copper tubing & insulation to tubing, connection of water drain piping, indoor to outdoor electric connection of suitable wire and servicing the stabilizer, and fixing the ACs properly in working condition, etc including testing & commissioning complete all the specified

M & L for copper tubing, confirming to relevant IS, of size 5/8 & 1/4" flare size or nearest size, 3 core 4 sqmm copper cable, PVC drain pipe upto ground level and insulation with superlon insulation to copper tubing as required length from indoor to outdoor unit of split AC complete as directed by Engineer in charge.

Material and labour for Chemical earthing with GI Electrode 3 mtr long with ground enhancing back fill compound all including soil testing, boring installation, transportation, earth work, testing of soil condition, FRP Chamber Cover and GI Strip 32 mm x 6 mm upto 7.5 mtr long complete all as specified and directed.

M & L for earth continuity conductor or main earthing lead fixed to wall as recessed and chasses or burried on ground or drawn in conduit/suitable protection pipe or any indicated situtation for loop earthing as required with 32 mm x 6mm GI flat strip including necessary welding joints/Pipe/GI nuts and bolts etc complete all as directed.

Supply and fixing down rod /extension rod for ceiling fan of size 4 feet long alongwith Clamps, Split pin, Bolts nuts, washers etc duly painted complete with all accessories all as directed

Supply, laying, testing, commissioning of cable XLPE insulated armoured heavy duty electric cable including end termination with necessary cable glands, lugs etc in trenches/ poles/ walls through pipes etc, ISI Marked (1100V grade) with multistranded aluminiuim conductor, cross sectional area 35 Sqmm 3.5 Core complete all as directed and removing old unserviceable cable of any size

Supply, laying, testing, commissioning of cable XLPE insulated armoured heavy duty electric cable including end termination with necessary cable glands, lugs etc in trenches/ poles/ walls through pipes etc, ISI Marked (1100V grade) with multistranded aluminiuim conductor, cross sectional area 25 Sqmm 4 Core complete all as directed and removing old unserviceable cable of any size

S&F light grade galvanized pipe ISI marked with all fitting, laid in trenches, under road or fixing on wall/pole/ crossing nallah etc of 40 mm bore complete all as specified and as directed .

Supply and fix in repairs MCCB adjustable type 3 pole 35 kA 200 A including dismantling and taking out the existing unserviceable MCCB of any type connecting up complete all as specified and as directed.

S & F modular switch 6A SP Two- way 230V white ivory finish complete all as specified and as directed.

S & F modular socket outlet 2/3 pin 6 amps, multipurpose 2 module 230 Volts, single pole one way suitable for plug tops, complete all as specified and as directed.

S & F modular socket outlet 2/3 pin 16 amps, multipurpose 2 module 230 Volts, single pole one way suitable for plug tops, complete all as specified and as directed.

S & F Bell push, modular type, 5 amp complete all as specified and as directed.

S & F Modular type stepped electronic fan regulator complete all as specified and as directed.

S&F bell electrical ding dong including hard PVC board ISI marked complete all as specified and as directed.

S&F in replacement of LED light fitting 10 Watt surface and wall mounted LED batten with Aluminium housing & integrated electronic driver of approved makes complete all as specified and as directed.

S & F in replacement of round recessed mounted AL die - cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation of 15W LED downlighter of white/neutral white colour temperature etc. prewired and all accessories complete all as specified and directed

S&F LED security light in replacement of luminaries 30 watt complete with all accessories and wall mounting bracket of suitable size including clamps, nut bolts etc. complete all as specified and as directed.

Supply and Fix exhaust fan of sweep 250 mm with louver heavy duty single phase suitable for 230 volts 50 HZ,1400 rpm and connecting up complete including provision of 3 core flexible cord from ceiling rose to connector of fan with cable of suitable size complete all as specified and as directed. (Make - Bajaj Cat part No - SUPREME DLX or equivalent in other approved makes)

S&F Sub main wiring complete with two single core 4 sqmm,1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 4 sqmm in and including PVC casing caping incl accessories complete all as specified and as directed. (Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 3 runs of 4 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

S&F Sub main wiring complete with four single core 4 sqmm and one core of 4 sqmm earth wire,1100volts FRLS grade, PVC insulated, stranded copper conductor cable with continuous copper earth conductor in and including PVC casing caping including accessaries complete all as specified and as directed. (Note:- Making good of disturbed surfaces will be done by contractor without any claims.(ii) 5 runs of 4 Sqmm conductor and one run of PVC casing caping shall be measured as one unit length.)

S&F servicing of geyser of 1.5/2 KW capacity, cleaning, overhauling, spray painting with one coat of synthetic enamel paint including writing MES no and refixing the geyser complete all as specified and as directed.

S&F MCB SPN DB 2 way, double door, with 200 amp rated busbar415 V, complete all as specified and as directed.

S & F for MCB double pole of rated capacity 32 amps, 240 volts breaking capacity 10 KA, B-curve complete all as specified and as directed.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover and MS angle iron frame, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete (NOTE:-GI earth wire and protection pipe beyond 7.5m will be measured and paid separately)

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of LT UG cable in soft/loose soil and getting out complete all as specified and directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point.

M&L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate for coping of poles including use and waste of form work for fair finished surface complete all as specified and as directed.

M & L for Reinforced concrete pipes of dia 150 mm 2 nos half round (each of 1 RM long for bottom and top) including levelling of ground before laying of pipe complete all as specified and directed.

S&F GI Tubes, 'light grade', galvanised, with all fittings laid in trenches of size 40 mm dia complete all as specified and as directed.

Supply, lay, test connecting and commissioning under ground cable of the size 6 sqmm 2 core, LT 1100 volt grade heavy duty XLPE insulated with aluminum stranded conductor armoured complete laid in trenches/fixed to poles /drawn through pipes with suitable size cable glands criping type cable lugs etc all as specified and directed

Supply and fix new generation, post top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution span aluminium landscape luminaire with high power LEDs as light source of cap 25 watts IP 65 protection in approved makes complete all as specified and as directed.

Gauri Associates

Parhar Enterprise

Suma Construction

SARATH ENTERPRISES

GS Associates

M/s.BAJRANG CONSTRUCTION

UNIQUE ENGINEERS

ANIL CONSTRUCTION CO.