CERTAIN MISC MAINT FOR AREA DEVELOPMENT INCLUDING BDY WALL/GATE/VIEW CUTTER AND CONNECTED WORKS IN THE AOR OF GE (EAST) DELHI CANTT-10

Amount

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc or for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete all as specified and as directed.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavatged matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete.

Demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M&L Plain cement concrete 1:3:6 type C - 2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M & L RCC M25 Design Mix using 20mm graded stone agg as in footings, plinth beam and bases of columns complete all as specified and as directed.

M & L RCC M25 Design Mix using 20mm graded stone agg as in columns , piers posts and struts complete all as specified and as directed.

M & L mild steel TMT bar 10mm dia and over cut to length,bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item 10 above but MS TMT bars 8mm dia and over upto and including 8mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M & L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and similar work; vertical or to batter complete all as specified and directed.

M & L formwork to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular rough finished surfaces of concrete laid flat complete all as directed.

Demolition of brick/block masonry built in cement mortar complete all as directed.

M & L Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radious built in CM 1:4 including all quioins, arches, pillars etc complete all as specified.

All as per item No 15 above but except bricks complete all as specified and as directed.

Taking down cement or cement lime plaster , any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement incl scafolding etc, complete all as specified.

M & L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed.

M & L 15mm thick polymer modified readymix cement based plaster Make : Ultratech (Brand name Readiplast) complying to IS-1661-1972, IS-2250-1965, IS-2402-1963) or equivalent as approved by GE, applied in ratio 1:4 as per manufacturer's instructions, on fair faces of brick masonry or concrete surfaces finished even and smooth, etc complete all as specified and as directed.

Dismantling granite, stone cladding, interlocking etc including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M & L 18 to 20 mm thick granite (colour as approved by GE) of any type work table rubbed and polished as in steps, jambs, pillars, window cills, platform, water point platforms , floor etc over and including 15mm thick cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching and moulding complete all as specified and as directed .

S & F wall cladding tiles (stone finish or as approved by GE) of size 250mmx140mmx7-8mm thick on vertical surfaces of wall over and including 10mm thick cement plaster in CM 1:4 (Make : Unistone/ultra or equivalent) and including dismantling of old tiles with backing complete all as specified and as directed.

S & F wall cladding tiles of size 300mmx600mmx10-12mm thick on vertical surfaces of wall over and including 10mm thick cement plaster in CM 1:4 (Make : Unistone/ultra or equivalent) and as per sample approved by GE including dismantling of old tiles with backing complete all as specified and as directed.

M & L 16 to 18 mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab and fixed with 1:3 cement mortar, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatmen complete all as specified and as directed.

M & L 75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing completed all as specified and directed.

M & L Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 60 mm thick, M-35 Grade laid dry in floor/path including 50 mm thick sand bedding layer complete all as specified and as directed.

M & L Pre- Polished coloured chequered cement concrete tiles 300 mm x 300 mm x 22- 25 mm thick, set, jointed and pointed in neat cement slurry over 20 mm thick screed bed in CM 1:6 including dismantling of existing floor tiles of any type and size complete all as specified and as directed.

M & L chequered cement concrete tiles 300 mm x 300 mm x 22- 25 mm thick (Grey cement no pigment) , set, jointed and pointed in neat cement slurry over 20 mm thick screed bed in CM 1:6 including dismantling of existing floor tiles of any type and size complete all as specified and as directed.

M & L Heavy duty external designer floor tiles, parking tiles etc any colour, shape and size exc. 0.06 sqm but not exc. 0.36 Sqm 8 mm to 12 mm mm thick , set & jointed in neat cement slurry and pointed flush with grey cement and pigments to match colour of tiles in floors over 15 mm thick screed bed or bedding layer in cement mortar 1:4, including dismantling of exisiting tiles of any type with bedding layer, complete all as specified and as directed.

M & L PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate as in brenching for manholes, drains, bands, coping, bed plate etc with slightly chamfered or rounded angles including necessary from work, if any, and finishing exposed surface even and smooth without using extra cement complete all as specified & directed.

M & L PCC (1:2:4) Type B2 using 40 mm graded stone aggregate as in block for fixing hold fast on boundary wall including necessary form work.

Dismantling old posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground.

Excavation in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning, filling in ramming earth or broken rubble in layers not exceeding 25 cm complete all as specified and as directed.

M & L for mild steel work , Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 including erection in ground complete all as specified and directed.

S & F in replacement Chain link MS galvanisd fencing any size or type ( approved by GE) including line wires, any mesh, size and type to any of standards , rails , straining bolts, etc including provision of bindings wire complete all as specified and directed.

S & F in repairs Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as directed.

Repair & fixing old existing galvanised. steel barbed wire restraining resecuring including making good staples or steel pins, etc. as directed (each line wire to be measured) complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 (Gde E-165)

S & F framed work such as in door frame, door shuters / gate of angel or other section with gusset plates, rails, braces, etc complete , drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings, including hings hold fast of Fe-290 (Gde E-165) quality etc complete all as specified.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed

S & F in replacement Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and as directed.

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of plain or corrugated AC sheeting any gauge thickness as in roof covering, complete all as specified and as directed.

S & F 2-3mm thick fibre glass reinforced translucent corrugated sheeting with additional reinforcement of chicken mess with two corrugation side lap fixed with 'L' or 'J' type or cranked hook bolts including dismantling of of existing sheeting of any type, complete all as specified and directed.

Providing and fixing "RAJSHRI" Brand factory made WPC railing combining WPC board/Fancy designer type grating and WPC frame 100% solid WPC (wood polymer composite) railing of required length and of 2' to 2.5' height , comprising of virgin PVC resin of K value 58-60 (Suspension Grade) , Calcium Carbonate and natural fibres (Wood Powders/rice husk//wheat husk) and non toxic additives, made from single extrusion process, WPC foam board with having minimum density 650kg/cbm and WPC frame having minimum density 780kg/cbm manufactured by "RAJSHRI" an ISO 9001-2015 certified Company, having good screw holding capacity (screw withdrawal strength of 2000N (Face) & 1100N (Edge) , Minimum comprising of 50N/mm2, Modules of elasticity 850N/mm2 and resistance of speed of flame of class A category with property of being termite/Borer free water /Moisture proof and fire resistance. For WPC railing WPC jali to be fixed with WPC frame of size 75x50mm with necessary supporting lengths at vertical as well as horizontal at wall frames to be fixed with 3"x3" GI 'L' or SS cleats to support vertical frame lengths including demolition /dismantling of existing RCC jallies with frames complete all as specified and as directed. (Make : Rajshree or equivalent) (Note : The said item shall be fixed over boundary walls/roof tops and in any other positions as requirement at site)

S&F Aluminium Composite panel (ACP Sheets colour as approved by GE) of 3/4 mm thick joint with cilicon/adhesive as per manufacture instruction including necessary aluminium framed work as required shape and size by welding etc fixing to wall/ceiling/ RCC column/boarding/Gates/Name Plates on gates with necessary fixing arrangements upto a height of 10 Mtrs including dismantling of existing sheets of any type complete all as specified and as directed.

S & F in repairs Stainless Steel letters of stainless steel 304 grade (letter size 6'' height and upto 2" depth or as approved by GE) placed on sign board, gate pillar , granite stone etc including all fittings and fixtures for fixing of letters, complete all as specified and as directed.

S & F in repair precast cement concrete type B0 1:2:4 (12.5 mm graded aggregates) louvres and jallies, 50 mm thick ( design and pattern as approved by GE) set in CM (1:4) including all mouldings but excluding frame fixed over boundary wall or walk ways or in any position etc complete all as specified and directed.

S & F in repair precast cement concrete type B0 1:2:4 (12.5 mm graded aggregates) louvres and jallies, 75 mm thick ( design and pattern as approved by GE) set in CM (1:4) including all mouldings but excluding frame fixed over boundary wall or walk ways or in any position etc complete all as specified and directed.

S & F pre-cast prefabricated reinforced cement concrete type B-l, 1:2:4 (20 mm graded aggregate) columns for wall as required suitable with proper size channel for fixing of Pre fabricated RCC wall panels of required size as per site requirement including fixing of columns to a required depth, fencing posts, straining or terminal posts, struts etc. for fencing , average sectional area n exc 100 sq. cm, with or without chamfered angles and flat, splayed, rounded or mitred tops as directed and all as specified.

All same as per srl item No 51 here-in-before but area exc 100 Sqcm not exc 250 Sqcm.

S & F Precast Prefabricated RCC wall Panels of 50 to 60 mm thick with suitable size in prefabricated columns and sealed properly with filling materials as per manufacturer's instructions, complete all as specified and as directed.

S & F Precast Prefabricated RCC wall Panels of 80 to 100 mm thick with of suitable size in prefabricated columns and sealed properly with filling materials as per manufacturer's instructions, complete all as specified and as directed

S & F in repair precast RCC coping/post of size 600x100x50 mm suitable for fixing of RCC Jallies in vertically & horizontally including necessary moulds and grooves as required in shape and size complete all as specified and directed.

S & F in repair dholpur dressed stone designer pattern louvres and jallies, 30 mm to 50 mm thick set in CM (1:4) including all mouldings top running frame fixed over bdy wall or walk ways or in any position including polishing, rubbing & including silicon treatment complete all as specified and directed (Fancy type design and pattern shall be approved by GE as per requirement at site).

S & F in repair dholpur stone dressed stone designer pattern post/column set in CM (1:4) of size average sectional area n exc 100 sq. cm and height as per requirement at site in vertically & horizontally including necessary moulds and grooves as required in shape and size fixed over boundary wall or walk ways or in any position including polishing, rubbing & including silicon treatment complete all as specified and directed (Fancy type design and pattern shall be approved by GE as per requirement at site).

S & F 30 to 40 mm thick lime/ sand stone slabs/ tiles polished , set and jointed in cement and stone dust mortar 1:3 and pointed in cement mixed with approved pigment to match over and including 15 mm thick cement mortar (1:4) including moulding to edge of slab complete all as specified and directed

M & L factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required (Size and pattern as approved by GE) and including dismantling of old existing kerb stone of any type and size etc complete all as specified and as directed.

M&L one coat of synthetic enamel paint to old painted steel surfaces of any description as in trusses , purlin ,rafters , ventilators etc over 10 cm width or girth incl prepration of surfaces complete all as specified.

M&L two coat of synthetic enamel paint over one coat of red oxide primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

M & L applying 2 to 3 mm thick wall care putty (JK wall putty , Birla wall putty or equivalent) on stone, concrete, plaster etc surface complete all as specified and directed

M & L for preparation of any type of surfaces old/new or in any position and applying two coats of floor paint as directed by Engr-in-Charge and at site complete (Make : Asian/Berger/Indigo)

M & L for preparation of new plaster external wall and ceiling surfaces of upto 4 storey buildings, boundary walls and applying Two coats of weather proofing exterior acrylic emulsion paint premium quality over a coat of exterior wall primer complete all as specified and directed. Allow 6-8hrs to dry the surface for painting of subsequent quotes complete all as specified and as directed by Engr- in-charge. Make : (BERGER (WEATHER COAT LONG LIFE 10), ASIAN (APEX ULTIMA), NEROLAC (EXCEL MICA MARBLE), DULEX (WEATHER SHIELD MAX)

M & L for applying high quality acrylic modified resin based texture of dholpur/Red sand stone pattern or any other shade/pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04kg/10Sqm to form film of 1-1.5mm thickness after scraping and propperly cleaning the surface to remove loose particle from the plaster surface followed by top coating with premimum acrylic smooth exterior paint with silicon additives of required shade by Two or more coats @ 1.43 ltr/10Sqm complete all as specified and as directed. Make : (BERGER (WEATHER COAT LONG LIFE 10), ASIAN (APEX ULTIMA), NEROLAC (EXCEL MICA MARBLE), DULEX (WEATHER SHIELD MAX)

M & L for preparation of New surface of stone, concrete of any description over 10 CM width or grith and applying two coat of plastic emulsion paint over a coat of primer (colour and patren as per approved by GE ) complete all as specified and directed.

M & L for preparation of old stone, concrete surfaces, of any description over 10 CM width or grith and applying one coat of plastic emulsion paint (colour and patren as per approved by GE ) complete all as specified and directed.

M & L for preparation of plastered or unplastered old decorated surfaces of wall and ceiling including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with Wall Care Putty and applying One coat of premium/Ist quality exterior acrylic emulsion paint of any tint all as per manufacturers instructions to achive desired finish at any height complete all as directed. Make : (BERGER (WEATHER COAT LONG LIFE 10), ASIAN (APEX ULTIMA), NEROLAC (EXCEL MICA MARBLE), DULEX (WEATHER SHIELD MAX)

M & L for preparation of plastered or unplastered old decorated surfaces of wall and ceiling including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with Wall Care Putty and applying Two Coats of Cement Base Paint at any height complete all as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of wall and ceiling including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with Wall Care Putty and applying one Coat of Cement Base Paint at any height complete all as directed.

Material and labour for preparation of new surface decorated brick/concrete plastered or unplastered surfaces of walls, pillars, cornices by brooming down etc and applying two coat of cement base paint over a coat of cement primer complete all as specified and directed by Engr -in Charge.

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge complete all specified and directed

S&F in replacement of LED Bollard light for pillar top 10W, 600mm height powder coated coated PDC Aluminium body with opal diffuser, 6500K/3000K, IP-65 protection including electrical connection complete all specified and directed. (Make- Polycab Cat Part No- PCGLBH201/Halonix Cat Part No-HLOB-05-10CW/WW or equivalent in Cromption/Havells).

Supply and fixing in replacement of LED post top lantern fitting powder coated aluminium die cast and spun aluminium with clear/opal diffuser 25 Watt incl LED driver with gallary suitable for mounting on 32/40 mm GI pipe including necessary electric connections complete all as directed. (Make- Polycab Cat Part No- PCGLPT0125O/C /Halonix Cat Part No-HLPT04-25CW/WW or equivalent in Cromption/Havells).

M&L in replacement of Sub main wiring with 2 run of 2.5 qmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to and including PVC concealed conduit with fitting medium grade 25 mm dia with fittings and including 2.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed and making good disturbed surface to match with existing one.

S & F in replacement of rigid non metallic PVC conduit with fitting medium grade 20mm dia inclusive of all tees, bends, elbow, reducers, bell mouth tube ends complete including cutting chasis in wall and making good the surface complete all as specified and as directed.

S & F in replacement of MCB DB confirming to IP 43 - IK 09 with single door , SPN 02 way complete with din rail Neutral and earthing bar after taking out the oldunserviceable DBs connection and making good the disturbed surfaces complete all as specified and as directed.

S&F in replacement of MCB SP, C Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F in replacement of MCB SPN C Curve type, 10 KA, 40 to 63 Amp, with over load and short circuit protection complete all as directed.

S&F GI Nipple 32mm dia, medium grade 300mm long embedded one and in PCC on the top of pillar complete all as directed.

M&L ATT by Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete

M&L ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron

M&L ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same

The new hut furnitures

imran construction company

Vipul Construction