SPECIAL REPAIRS TO BUILDINGS AG2 AZ2 AE2 AND AF2 IN SAILORS MARRIED ACCOMMDATION AT NEW NAVY NAGAR UNDER GE NW NAVY NAGAR COLABA MUMBAI

Amount

Material & Labour for chipping, removing carefully concrete work by low impact hammer, breaker without damaging the structure and cleaning and disposal of debris out side the MoD land etc complete as directed by Engr-in-charge. Hard concrete should not be removed by force complete all as specified and directed by Engineer-In- Charge

Material & Labour for Building up the profile of structrual members by using latex adhesive (MONOBOND) modified air cured mortar system (Polymer modified mortar) (1-5-15) = 1 monobond 5 cement 15 sand ) in damaged areas in 30 mm thickness including leveling profiling etc complete) complete all as specified and directed by Engineer-In- Charge

Material & Labour for carry out application of Bi Polar migratory corrosion inhabitor EPCO KP _ 100 Protectssil CIT/Ferogard 903 on concrete surface (this inhabitor shall have migratory kind of property which permit the material to migrate to a vertical extend of 100 mm , through pores of concrete inhabiting the corroser and depassivating the elctro chemical reaction it should have property to attack anode as well as cathode which is purely alkaline in nature (Ph 9.5) so it has no carcinogen activities with concrete complete all as specified and directed by Engineer-In- Charge

Material & Labour for cleaning existing reinforcement with wire/rotary wire brush, making the surface free from loose material dirt etc, complete applying two coats of alkaline rust converting primer (i.e. rust remover) FEOVERT conforming to ASTM-B-117, on the rebars including cleaning the reinforcement , wire brushing to remove loose rust spalls with time interval 6 hrs between the coats and applying protective coating (IPNET - RB complete all as specified and directed by Engineer-In- Charge

Material & Labour for providing and applying two coats of anti-rust protective coating in the form of Acrylic Polymer mixed with Cement in 1:1.5 proportion (1 part polymer and 1.5 parts Cement) on rebars after cleaning of rust scales as per manufacturers instruction (measurement on the basis of exposed concrete area). (Make : IPNET of Krishna Conchem, New Coat from Dr Fixit or as approved by GE ) complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster or micro concreting conforming ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bonding between old concrete and new concrete complete all as specified and directed by Engineer-In- Charge

Material & Labour for providing micro concrete (Molith-MC) M-40 including lifts, working platform, scaffloding up to 20mtrs ht of bldg, and applying jacketting around columns/beams with shuttering, drilling holes and fixing shear anchor as per specification complete all as specified and directed by Engineer-In- Charge (Make : Micro concrete of Dr. Fixit or as approved by GE ) (Note : (a) Reinforcement, form work shall be measured and paid seprately

Material and labour for applying curing compound over concrete surfaces as per manufactures instruction complete all as specified and directed by Engineer-In- Charge

Material & Labour for drilling and fixing Rohibb teflon in RCC members, including drilling holes of 12 mm dia , 50 to 100 mm deep holes in structural member at the interval of 500mm c/c in staggered manner or as directed by Engr In Charge in RCC structural element. Work shall be carried out as under :- (a) Cleaning of holes - cleaning the holes by air blower prior to fixing nozzles (b) Fixing of nozzles - Insert 12 mm dia Rohibb teflon nozzle in cleaned holes. External end of nozzles to be machine to recieve outlet of grouting gun. Fix it in side the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for 12 hrs (c) cutting of nozzles - Cut the nozzle by chisel after completion of grouting without damaging structural element complete all as specified and directed by Engineer-In- Charge

Material & Labour for injecting of site cement slurry grout in the ratio 1:2 ( 1- Cement 2- Water ) including super plasticiser (Super com -100) 250 ml/50 kg. Mixing shall be done mechanical mixer continously stirring mechanically to keep cement particle in suspention .Injection of approved/specified grout by means of pump at a pressure of 0.5 Kg /cm sq etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled (for repair to wall and slab) complete all as specified and directed by Engineer-In- Charge

Material & Labour for injecting viscosity MONOPOL (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzle refused to accept the grout, including mixing of material component ( part A & B) in the required qty as per manufactures instruction by weight batching. Grouting maintain the presssure at exit (0.5 to 1 1.kg/cm2) by monitering pressure guage at exit . Grout at material through prefixed nozzle in the structural element @ 100 ml per nozzle. Repeat the process for all nozzle (Columns and beam) complete all as specified and directed by Engineer-in-Charge.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed by Engineer-in-Charge.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed by Engineer-in-Charge.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge.

All as per item No 15 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed by Engineer-in-Charge.

Providing and fixing MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour including polyster resin based grouting materials for grouting the pins sourced from manufacturer's such as Fosroc or Krishna Conchem or as approved by GE complete all as specified and as directed by Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles including disposal of debris out side the MoD land etc complete all as specified and as directed by Engineer-in-Charge. Note:- Cost of uprooting of shrubs is included in the item rate.

Material & Labour Brick work with sub class 'B' brick straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster on brick or stone walls, any description, including raking out joints, hacking for key, scrubbing down with water, etc including disposal of debris out side the MoD land etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for cement plaster 10 mm thick using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare Pvt .Ltd/ or as approved by GE, having minimum composition of C:S :: 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces as final rendering, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing etc. complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for cement mortar with forced application (guniting) in CM 1:4 of 20mm-25mm thickness mixed with latex additives (MONOBOND) @ 200ml per bag of cement applied over exterior masonry and concrete surfaces upto 16 mtrs height of bldg including necessary scaffolding and working platform including cleaning the surfaces, curing etc. Complete all as specified and as directed by Engineer-in-Charge. (Note : Rate includes the rate of MONOBOND. No separate payment will be paid for MONOBOND).

Material and labour for 15mm thick rendering using factory manufactured pre mix / ready mix mortar with the addition and including WPC of UltraTech WP+ 200 or other equivalent @ 200ml per bag of mortar on fair faces of brick or concrete surfaces complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for plastering 15 mm thick on other than fair faces of brickwok or concrete surfaces of wall in cm 1:6 and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Sand faced cement plaster 10 mm thick as in ceiling in CM 1:3, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or as approved by GE,including using richer mix for making corners if necessary, at all places and level, including making grooves of existing size wherever required, including cleaning the surfaces, curing etc. complete all as specified and directed by Engineer-in-Charge.

Material and labour for applying two coats of rain coat (brand name) or equivalent over a coat of primer as per manufacturer’s instructions using fully automatic Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and accessories for applying rain coat should be able to spray in hard to reach areas and penetration of rain coat on the surface complete all as manufacturer’s instructions and directed by Engineer In Charge. (The makes of Rain coat (brand name) or equivalent shall be as specified in Particular Specifications.)

Complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc by skilled labour complete all as specified and as directed by Engineer-in-Charge.

Material and labour for waterproof cement based putty @ 1 Kg(undiluted) per sq mtr. of average thickness 2 mm over the plastered/old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps:- Step 1) Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2) Apply the first coat the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3) Allow 6-8 hrs time to dry the putty surface complete all as specified and as directed by Engineer In Charge

Material and labour for applying two coats of oil bound distemper over a coat of primer using fully automatic Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. Note : Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application) complete all as specified and as directed by Engineer In Charge

Material & Labour for preparing new plastered surfaces of wall and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparing new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & Labour for applying two coats of white wash on old decorated ceiling incl complete removal of existing treatment by washing, rubbing down complete all as specified and directed by Engg-In-Charge.

Material & Labour for preparing old previously treated wooden surfaces over 10 cm of width or girth and applying two coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Material & Labour for preparaing of old steel surfaces of any description and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Complete removal of exisiting water proofing treatment of roof including demolition of brick bat koba/pcc padding of any thickness , cleaning with wire brushes etc and removal of debris outside MoD land complete all as specified and directed by Engineer-in-Charge.

Material and labour for Plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) addition and including WP+ 200 of UtraTech / Shali Plast LW+ of STP / Pidilite URP of Dr. Fixit or as approved by GE and per manufactures instruction Before laying concrete surface shall be cleaned and a bond coat of slurry with Shali Crete URP (of STP) or quivalent with cement to be applied. All cracks in slab to be openend in 'V' groove and filled with Shali Fix RMC a Polymer Morter of STP/ equivalent complete all as specified and directed by Engr-in-Charge.

Material & Labour for protecting the roof including parapet wall with polyurethane hybrid next generation liquid applied roof top coat waterproof coating with flutyne protection technology, complete as specified below: (a) Apply one coat of primer on cleaned and dry surface spreading at the rate as per manufacturer’s instructions and allow primer coat to dry for 6 to 8 hrs. (b) Apply 1st coat of polyurethane hybrid next generation liquid applied roof top coat waterproof coating without dilution and spreading at the rate as per manufacturer’s instructions. Allow the first coat to dry for approximately 4-6 hours before applying the 2nd coat at 90° to the first coat. (c) Laying of 45 GSM Fiber glass mesh incorporated on the 1st coating as a sandwich layer when the first coat is still in wet condition. (d) Apply 2nd coat of polyurethane hybrid next generation liquid applied roof top coat waterproof coating without dilution at 90° to the first coat and spreading at the rate as per manufacturer’s instructions. (e) Apply 3rd coat of polyurethane hybrid next generation liquid applied roof top coat waterproof coating without dilution at 90° to the 2nd coat and spreading at the rate as per manufacturer’s instructions. Ensure there are no pinholes or air bubbles on the membrane. (f) Allow the system to air cure for 7 days minimum. Note : The work shall be carried out by authorised applicator from manufacturer only.

Material & Labour for Water proofing treatment to rain water spouts of entire roof terrace by opening of all the existing failed loose pipes and its Joint (In Old Structure), replacing the same by an appropriate dia pipe( not less than110mm) followed by Application of two coats of cold modified bituminous components to ensure leakage free joint.(work includes filling of mortar and making good the same) complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches n exc 1.50m wide and nexc 1.50m in depth for foundation etc nexc 10sqm on plan and nexc 1.50m in depth and getting out in soft loose soil complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up SWG drain pipe of 150mm dia complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

Material & Labour for concrete bed to drain pipes in cement concrete (1:3:6) type C2, 150 mm bore incl packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and directed by Engineer-in-Charge.

Material and labour for 150mm bore Reinforced concrete pipes, class NP2, laid in trenches and jointed with cement slurry and yarn complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains of 150mm dia pipe and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specied and directed by the Engr-in-Charge

Returning, filling, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge

Removing excavated (soil) materials and deposited out of MoD land.up to a distance of 15 KM complete all as specified and as directed by Engineer-in-Charge.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 32mm dia LDPE PVC pipe of pressure rating 6 kgf/cm2 fixed complete to for WHB and kitchen sink including socket, tee, bend etc & screw complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 40mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm of fixed to wall, floors for drain out the waste water from Kitchen Sink, WHB etc including socket, tee, bend etc & screw complete all as specified and directed by Engr-in-Charge.

Supply and fixing PVC (SWR) 110mm bore pipes in any length with rubber ring joints fixed to wall with dash through fastners and clamp of 25 x 1.5 mm FI incl all fittings like sockets, bend, junction, elbow etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110mm PVC (SWR) bends complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) branch piece, Single (single Y) equal or unequal for 110 mm bore access door eye. complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) branch piece, double (double Y) equal or unequal for 110 mm bore access door eye. complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110mm bore PVC floor trap with SS gratings incl jointing to waste pipe with solvent cement complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC 160mm bore rain water pipes in any length with rubber ring joints fixed to wall with dash through fastners and clamp of 25 x 1.5 mm FI incl fittings complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for 160 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 160mm PVC (SWR) bends complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 160mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposal of debris out side the MoD land etc complete all as specified and directed by Engineer-in-Charge.

Material and labour Non - skid coloured rectified ceramic tiles 7 to 8 mm thick of size area of each tile exc 0.09 Sqm but n.exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including bedding layer of 20mm thick using factory manufactured pre mix / ready mix mortar C:S :: 1:4 for laying floor finishes complete all as specified and directed by Engr-in-Charge.

Material & Labour for coloured glazed ceramic tiles in vertical surface 300x450x7 to 8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick plaster using factory manufactured pre mix / ready mix mortar C:S :: 1:4 complete all as specified and as directed by Engineer-in-Charge.

Material and labour Non - skid rectified ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile 600mmx600mm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including bedding layer of 20mm thick using factory manufactured pre mix / ready mix mortar C:S :: 1:4 for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

Ditto all as per item No 63 above but as in skirting over & incl backing layer of 10mm thick rendering using factory manufactured pre mix / ready mix mortar complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for machine cut pre-polished kota stone slab as in flooring, steps, window cill and jams etc or similar work 20-25mm thick over and including bedding layer of 20mm thick using factory manufactured pre mix / ready mix mortar C:S :: 1:4 for laying floor finishes laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 20-25mm thick machine cut pre-polished kota stone slab in riser of steps, skirting, dado and pillar laid over and including 10mm thick plaster using factory manufactured pre mix / ready mix mortar C:S :: 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Material & Labour for udaipur green/baroda green marble slab 18-20 mm thick on vertical surface, machine cut, bedded and jointed with grey cement slurry over and including 15mm thick plaster using factory manufactured pre mix / ready mix mortar C:S :: 1:3 and pointed with white cement using marble dust with admixture of pigment to match the shade of marble slab including grinding and polishing complete all as specified and directed by Engineer-in-Charge.

Material and labour for 18-20 mm thick Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over including bedding layer of 20mm thick using factory manufactured pre mix / ready mix mortar C:S :: 1:4 for laying floor finishes including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engineer-in-Charge.

Rounding to edges of stone slabs (kota/granite etc) one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge.

Material & Labour extra for forming grooves over granite or kota stone slab as in staircase complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas, chimny and similar suspended work including cutting of reinforcement cut as required to facilitate demolition including removing of debris out side MoD land complete all as specified and directed by Engineer-in-Charge (Reinforcement cut as reqd to facilitate to demotion)

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings or chajjas (FRP or any other pattern) complete all as specified and directed by Engineer-in-Charge.

Material & Labour pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Cutting chases, pinning in and making good to facings of brick/concrete/stone walling where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer-in-Charge.

Material and labour for filleting in any position and to any shape of section area not exc 25 sq cm in cement sand mortar 1:4 including all mitres, stops etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 10 mm dia 100 mm long dash through fasteners bolts fixed in concrete or brick work to hold brackets etc complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

Material & Labour for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

Supply and fixing mild steel rolled section as in main and cross beam, hip and jack rafters, purlins where connected to common rafter and running rails etc complete conforming to Fe-410- W(Gde?E-250) quality?B including working platform/scaffolding) Complete all as specified and as directed by Engr-in-Charge.

Preparaing of new steel surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Resecuring or easing and adjusting and finally refixing the shutters into the same opening after taking down wooden shutters exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed by Engineer-in-Charge

Resecuring or easing and adjusting and finally refixing the shutters into the same opening after taking down wooden shutters n.exc 1 Sqm each complete all as specified and directed by Engineer-in-Charge

Supply and fixing Aluminium anodised section 15 micron for window (Sliding type) / ventilator (Partly fixed partly louverd type) etc of anodised aluminium section ventilators partly fixed partly louvered type comprising frame, shutters, locking arrangements including necessary jamming, glazing pins, neoprene beading, glazing pin screw, levered aluminium sections for louvered glass, rollers , handle etc including taking down existing window complete all as specified and directed by Engineer-in-Charge. Note: (a) Glazing shall be measured separately. (b) Item shall be paid as per weight of aluminium section. (c) Rate quoted shall be inclusive of neoprene beading, glazing clips, screw etc as required which not be measured for arriving the weight. (d) Rate shall be inclusive of the aluminium handle, locking arrangement including complete packing with silicon gel around contecting surface of aluminium and including matching the existing surface area complete all as specified and directed by Engineer-in-Charge. . (e) Aluminium window / ventilator etc to be fixed with cadmium plated screw not more than 300mm c/c.

Material and labour aluminium anodised powder coated grill with suitable aluminium anodised frame section manufactured by M/S Deco grill pattern DG-102 (7.5mm dia and aparture 50mm) complete all as specified and directed by Engr-in-Charge.

Supply and fixing 5.5 mm thick plain glass ordinary quality in square n.exc 0.50 sqm each fixed to aluminium window frame complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 5.5 mm thick frosted glass ordinary quality in square n.exc 0.50 sqm each fixed to aluminium window frame complete all as specified and directed by Engineer-in-Charge.

Material & Labour Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or wooden/ Aluminium beadding complete all as specified and directed by Engineer-in-Charge.

All as per Item No 87 but fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Taking down chawkhats or frame (w/o taking off shutters from the frames) but exc 1.50 but n.exc 4.00 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frame (w/o taking off shutters from the frames) n.exc 1.50 Sqm each complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 2nd class hard wood plain, solid straight chowkats and frames, wrought framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 2nd class hard wood 35mm thick factory made plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial or 12mm veneered particle board with commercial veneer on both faces the size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed by Engineer-in-Charge.

Suppling and fixing 2nd class hardwood 35mm thick glazed and skelton shutters, open rebated and prepared to receive wire mesh edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing mesh etc, sizes of members of shutters as specified in SSR complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 2nd class hardwood bullnosed splayed, chemfered or rounded on edge fillets rectangular in section, sectional area exc 6 but n. exc 13 Sqcm fixed in repairs fixed with nails complete all as specified and directed by Engineer-in-Charge

Supply and fixing 2nd class hardwood bullnosed splayed, chemfered or rounded on edge fillets rectangular in section, sectional area exc 13 but n. exc 25 Sqcm fixed in repairs fixed with nails complete all as specified and directed by Engineer-in-Charge

Material & Labour for preparing new wood or wooden surfaces over 10 cm of width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MS holdfast, wall ties and similar articles confirming to Fe-290 Gde- E-165 complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC (1:3:6) type C-1 (20mm graded agg) for fixing of hold fast complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 90 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges shall be paid separately)

Taking down shutters of any description exc 1 sqm but n.exc 2 Sqm each and complete all as specified and directed by Engineer-in-Charge.

Taking down Shutters of any description n exc 1 Sqm each complete all as specified and directed by Engineer-in-Charge.

Material and labour for 18-19mm thick Block boards, grade1 quality, interior grade, decorative type with decorative face veneer on both faces fixed with screws to timber frame-work including teak wood lipping, 6mm thick fixed with nails as in Cup board shutter and shelves complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for 30mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 125 mm SS butt hinges fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 100mm size SS butt hinges fixed with SS screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 100mm long aluminium anodized barrel tower bolts of extruded section fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section fixed with SS screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 100mm size extruded aluminium alloy handles, fabricated type anodised fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 150mm size extruded aluminium alloy handles, fabricated type anodised fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed of length 300 mm fixed with SS screws complete all as specified and directed by Engineer-In- Charge

Supply and fixing Floor door stopper of 140mm aluminium alloy body and tongue with hard drawn steel spring fixed with SS screws complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs 125mm size MS butt hinges fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 150mm long aluminium, anodised, barrel tower bolts of extruded section fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 150mm long extruded aluminium alloy handles, fabricated type, anodised fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs 300mm long aluminium alloy, anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs floor door stopper of 140mm aluminium body and tongue anodised with hard drawn steel spring fixed in floor fixed with SS screws complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repair hasp and staple 150mm size, safety type, aluminium anodised with mild steel hinge pin fixed with SS screws including bolt to hinge plate and fixed with screw complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing mild steel 300 mm, ordinary rat tail rod pattern springs including roller androller plate fixed with SS screws complete all as specified and as directed by Engineer-in-Charge

Supply and fixing 600mm long powder coated MS kitchen rail, wall mounted type with 10 Nos of hooks made of 3mm dia MS rod and welded/ riveted on 20mm x 2mm flat and necessary screws, pluges fixed with SS screws complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for stainless steel cloth hanger peg set of 6 of premium quality fixed with CP brass screws complete all as specified and directed by Engr-in-Charge.

Supply and fixing magic eye fancy type of brass for door including drilling cutting of holes and making good complete all as specified and directed by Engr-in-Charge.

Supply and fixing chromium plated towel ring fixed with SS screws complete all as specified and directed by Engr-in-Charge.

Material and labour for welded mesh n.exc 4Kg/ Sqm including beading, fillets, nails including dismantling old unserviceable mesh complete all as specified and as directed by Engineer-in-Charge

Demolition of cement concrete un-reinforced not exc 15 cm thick of any description and at any position including disposal of debris out side the MoD land etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for 75mm thick PCC (1:3:6 ) type C-1 using 20 mm graded stone aggregate as in plinth protection laid in panels finish the top surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & Labour for cement concrete 1:4:8 type D2 using 40mm graded aggregate and filling mass concrete in foundation complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair vitreous china wash down water closet (EWC) (Pedestal) P or S trap including PVC seat cover closed pattern with flat bottom and cover and mild steel chromium plated hinge device,connection to drain or outgoing pipe and to flushing pipe, antisyphonage pipe joint to socket or stoper. complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for chromium plated brass telephonic health faucet shower with flexible tube of stainless steel, 1.00 Mtr long with CP holder, multi flow 15mm dia for iron pipe or for brass ferrule etc. complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repairs lever operated 15 mm dia of 2-in-One chromium plated brass Bib taps, with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engineer-in-Charge.

Material & Labour 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets in repairs complete all as specified and as directed by Engineer-in-Charge.

Material & Labour aluminium powder coated drapery rod of 20 mm dia including curtain rings complete all as specified and directed by Engineer-in-Charge

Supply and fixing aluminium powder coated fancy type domes cum bracket (20 mm dia) fixed to both ends of the drapery rod and wall complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC cabinet box type looking mirror of size 450x600x110mm with 5mm thick of bevelled edge mirror as a shutter along with shelf partition inside the cabinet including necessary secure plug complete all as specified and directed by Engineer-in-Charge. Make : As approved by the GE.

Supply and fixing SS soap dish, any type, fixed toplugs with chromium plated brass screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repairs brass chrominim plated tublar towel rail, 20mm dia, D type, 60CM long between flanges complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Vitreous China wash basin, white, flat back, size 550 x 400 mm excluding water taps waste chain plugs and porcelian stopper but including brackets complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair CP brass swan neck type pillar tap of 15mm dia, screwed down high pressure fancy type 250mm long complete all as specified and directed by Engineer-in-Charge

Material & Labour 32 mm dia waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms) including waste pipe complete all as specified and directed by Engineer-in-Charge

Supply and fixing PVC connectors of 15 mm size with PTMT nuts of length 600 mm length complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs sinks with draining board made of stainless steel 1mm thick, kitchen with plugs, washers & wastes cupling and waste pipe including fixing cantilever brackets & connecting union to pipe overall size 915mm x 460mm x bowl size 410 x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs stainless steel plate rack 0.63mm thick stainless steel sheet overall size stainless steel plate rack 31” x 31” x 10” kitchen rack all as specified and as direted by Engineer-in-Charge.

Supply and fixing of 04 pieces pulley operated Cloths Drying system casting of Aluminium pipe of outer dia 22 mm inner dia 19.8 mm and channel pair of length 2.50 mtr with pulley made up of Devil mounted and fixed with self tapping screw. Rope will be HDPE double core of 4 mm with rope Guide at locking system to hide rope. Channel to be dia of minimum weight of pipe shall not be less than 0.20 kg/Rm and maximum weight of pipe in one unit not less than 2 kg. Weight of rope shall be not less than the 550 gms / mtrs. Make : Easy dry or as approved by GE

Supply & Fixing for Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing in SSR Part II and directed by Engineer In Charge (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

Supply and fixing of 18 mm thick Celuka ply of Plain colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete all as specified and as directed by Engineer-in-Charge. (Make- Rajshri Plastiwood or as approved by GE).

Supply and fixing of 18 mm thick Celuka ply of one side Prelam/Rigidlam and other side plain white colour to make kitchen cabinet Shutter/ drawer Front shutters in double panel complete all as specified and as directed by Engineer-in-Charge. (Make- Rajshri Plastiwood or as approved by GE)

Supply and fixing of auto closing hinges openable at 0/90 degree for kitchen cabinet shutters complete all as specified and as directed by Engineer-in-Charge. Make: ( Hettich, Ebco, Prime or as approved by GE )

Supply and fixing of stainless steel handles 100 mm size for kitchen cabinet shutters complete all as specified and as directed by Engineer-in-Charge. Make: ( Hettich, Ebco, Prime or as approved by GE)

Material and labour machine cut cudappah stone 20-25 mm thick over base,laid and jonted with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for number plate made out of 3mm thick acrylic sheet and size 100mm x 180mm including written 3 numeric letter height not less than 65mm (colour, design & pattern or as approved by Engineer In Charge) fixed with CP brass screws complete all as specified and directed by Engr-in-Charge.

Material & Labour for two coats of floor guard paint on surface of old paver block and concrete tiles including cleaning with brush and water to prepare of clean surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour providing and injecting chemical emulsion for post construction anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion at 2.25 litre per linear meter including drilling and plugging holes etc with white cement and match the surface to existing apron complete all as specified and directed by Engineer-in-Charge.

Material and labour for treatment of soil under existing floors in junction with wall (internally) using chemical emulsion @ 1 litre per hole at 300mm center to center and 300mm deep including drilling and plugging 12mm dia holes with cement mortar 1:2 or white cement to match the existing floors complete all as specified and directed by Engr-in-Charge.

Material and labour for post construction treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors all as specified and as directed by Engineer-in-charge.

Material and labour for post construction treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with sealing compound complete all as specified and as directed by Engineer-in-Charge.

Demolition of lime concrete of any description and in any position not otherwise specifically provided for including china mozaic, WC etc. including disposal of debris out side the MoD land etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour cement concrete 1:5:10 type E-2 with 40mm graded stone coarse aggregate in sunken floor complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 32mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm as in spout pipe each 50 cm long, cutting to shape as required, cutting through wall of any thickness, fixing in PCC (1:2:4) tpe B-1 making good the damaged portion by rendering in CM (1:4) and finished the surface to match the existing surface complete all as specified and directed by Engineer-in-Charge.

Dismantling of paver blocks and concrete tiles any description any position including removing from site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 60 mm thick coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment including sand cushioning of (25 to 40mm average) thickness and watering and consolidation complete all as specified and as directed by Engineer-in-Charge.

Treatment of sunken floor slab comprises of the following specifications and all as specified (i) Material and labour for cleaning of the sunken /lowered portion of the RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chiesel out any mortar sticking to the surface and brooming / washing completely. 40 mm avg thick PCC 1:2:4 type B-0 using 12.5 mm graded aggregate as in padding concrete to achieve proper slope including 50 mm dia 350 mm long medium grade GI pipe spouts with wire guage on inside mouth to be fixed. (ii) Rendering of uneven surfaces with 10 mm thick using factory manufactured pre mix / ready mix mortar addition and including WPC of UltraTech WP+ 200 or other equivalent @ 200ml per bag of mortar fill it with water and check dampness and seepage. where dampness and seepage noticed nozzles shall be fixed and grouting carried out. (iii) All junctions points of side walls where CI/GI pipes are passing through shall be sealed with epoxy putty (iv) After drying putty wash the slab and sides of sunken portion with water and make it clean and clear

(v) Material and labour for applying two coat of polymer modified cementious water proofing coating as per manufactures instructions to bottom and vertical sides up to finished flooor level +100 mm height. The thickness of two layer shall be 1 mm. When the second layer is still sticky, coarse sand spry shall be carried out or vertical and bottom surface of the sunken portion all as specified and directed. (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20 mm thick using factory manufactured pre mix / ready mix mortar addition and including WPC of UltraTech WP+ 200 or other equivalent @ 200ml per bag of mortar including rounding of corners and junctions sloping towards spout. Note:Test the water proofed area (ponding test) by filling water for atleast 72 hours and tested for leakage seepage and to the entire satisfaction of GE . Test shall be done in presence of reps of PMG and record for each sunken slab shall be maintained. the treatment shall be carried out by authorised applicators of chemicals. (vii) All pipes laid in sunken portion shall be covered with 50 mm thick PCC 1:2:4 all around after painting with anticorrossive black japan paint

Taking down carefully copper/ aluminium point wiring i.e. light, fan, socket or power/points complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good disturbed surfaces of ceiling, walls, floors, etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for point wiring with PVC insulated unsheathed single core multi stranded copper conductor 1.5 sqmm, 1100 volts grade cable, FRLS, passing through PVC casing caping including accessories and provision of PVC box for mounting of modular Switchs & Sockets as required at site as directed by Engineer-in-Charge including one run of PVC insulated unsheathed multistranded copper conductor cable 1.5 sqmm (green colour) FRLS earth wire and connected to earth dolly for the following:- NOTE : Circuit conductor from MCB DB to Switch boards should not be less than 2.5sqmm.

One light/Exhaust/Ceiling fan point controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

One 3 pin switch socket combination 5 Amps on the same board with other switches complete all as specified and as directed by Engineer-in-Charge.

One 3 pin switch socket combination 5 Amps, independent complete all as specified and as directed by Engineer-in-Charge.

One bell point controlled by one push button complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 163 here in before but with 2.5 Sqmm copper conductor with 2.5 Sqmm cable for earth conductor for one 3 pin 15 Amps socket outlet controlled by one switch. Separate circuit shall be drawn from MCB. No taping from light circuit complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement with modular switch, 1 module, single pole one way 6 Amp conforming to IS:3854 and ISI marked complete all as specified and as directed by Engineer-in-Charge. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply and fixing in replacement with modular switch, 1 module, single pole one way 16 Amp conforming to IS:3854 and ISI marked complete all as specified and as directed by Engineer-in-Charge. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply and fixing in replacement with ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body of size 60x50mm complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement with modular socket 6A, 3 pin, 2 module conforming to IS:1293 : 2019 and ISI marked complete all as specified and as directed by Engineer-in-Charge. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply and fixing in replacement with modular socket 6/16A, 3 pin, 2 module conforming to IS:1293 : 2019 and ISI marked complete all as specified and as directed by Engineer-in-Charge. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply and fixing in replacement with modular bell push switch, 1 module, single pole one way 6Amp ISI marked complete all as specified and as directed by Engineer-in-Charge. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply and fixing in replacement with modular electric bell ding dong, AC, 230V single pole complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement with modular stepped type fan regulator, 2 module, single pole one way ISI marked complete all as specified and as directed by Engineer-in-Charge. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply & Fixing Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge..

Supply & Fixing Retrofit LED lamp 9 Watts complete all as specified and as directed by Engineer-in-Charge.

Taking out old wooden/PVC board and disconnecting all electric connection from switches, board and Supply and fixing in replacement with modular PVC Gang box of 8 module, ISI marked for mounting of modular switches and sockets including blank plate for blank module. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

All as per Item No- 175.00 above but of modular PVC Gang box, 6 module

All as per Item No- 175.00 above but of modular PVC Gang box, 4 module.

All as per Item No- 175.00 above but of modular PVC Gang box, 3 module.

All as per Item No- 175.00 above but of modular PVC Gang box, 1/2 module.

Supply and fixing modular white cover plate with frame, 8 module complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing modular white cover plate with frame, 6 module complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing modular white cover plate with frame, 4 module complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing modular white cover plate with frame, 3 module complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing modular white cover plate with frame, 1/2 module complete all as specified and as directed by Engineer-in-Charge.

Taking down old unserviceable FTL/batten/bulkhead fittings and supply and fix LED batten fitting 20 Watt, 240V, 4ft CDL/NW comprises of extruded channel in thermally conductive material with decorative end cap and high translucent serration milky white diffuser of high optically efficient plastic FR grade. The luminaire is pre-wired with high efficiency electronic driver having operating voltage 140-270V, P.F >0.95, THD <20% and IP20 protected alongwith provision of two Nos of PVC box of size 75x75x20mm for mounting light fittings complete all as specified and as directed by Engineer-in-Charge. The contractor shall provide test certificate from authorized lab.

All as per Item No-185.00 above but LED integrated batten of 10 watt 2ft complete all as specified and as directed by Engineer-in-Charge. Make of Light Fitting : Wipro/Crompton/Philips/Bajaj/Polycab

All as per Item No-185 above but linear LED batten of 10 watt 2 feet, inbuilt sensor based smart LED auto dimmable motion sensor with 25% dimmer illuminous in ideal time made from powder coated aluminum extruted channel prewired with complete accessories complete all as specified and as directed by Engineer-in-Charge. Make of Light Fitting :Bajaj/Polycab/Halonix

Supply and fixing MCB DB SPN conforming to as per IEC 61439-3 and IP 43, IK 09 with acrylic door, 8 way complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces by plastering or PCC work inclding distembering to the affetced to walls complete all as specified and as directed by Engineer-in-Charge.

Taking out Old Unserviceable and Supply and fixing MCB SPN, 32 Amp, 10 KA, 230 Volt complete all as specified and as directed by Engineer-in-Charge.

Taking out Old Unserviceable and Supply and fixing MCB, single pole, upto 20 Amp, 10 KA, 230 Volt complete all as specified and as directed by Engineer-in-Charge.

Taking out unserviceable ceiling fan and deposit to MES Store, supply and replacement with ceiling fan 230V, 50 Hz, AC, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete with hanging arrangement by down rod alongwith steel wire rope for additional safety in ceiling fan with all allied accessories and connecting up with three core, 0.75 sqmm PVC insulated copper conductor cable complete all as specified and as directed by Engineer-in-Charge.

Taking out unserviceable exhaust fan and deposit to MES Store, supply and replacement with Exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm including connection as required at site with three core flexible copper cable complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm including connection as required at site with three core flexible copper cable complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing submain wiring PVC insulated, PVC sheathed, armoured, FRLS, 1100V grade, 2 core 6 sqmm stranded copper conductor electric cable laid on wall/ roof/ duct complete with proper saddling and connecting meter to DBs with glands including taking out existing unserviceable cable complete all as specified.

Material and labour for replacement of existing old u/s submain wiring with two single core PVC insulated flexible copper conductor cable of size 4 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 4 Sqmm as earth lead in and including concealed PVC conduit and making good the disturbed wall surfaces to match with existing specification all as required at site or directed.

Material and labour for snap-on trunking system with cover, angles, bends and all accessories and fitting of size 50x80 mm fixing on wall complete all as specified and as directed by Engineer-in-Charge.

Supply, install, testing and commissioning of meter cabin panel mounted on angle iron frame 40x40x5 mm grouted on floor,cubical indoor type for 415V, 3 phase, 4 wire made out of 2 mm thick CRCA sheet weather, vermin proof factory fabricated, CPRI approved, front open hinged door with locking arrangement powder coated, individual compartment for MCCBs and 200 Amps rated copper bus bar(All in equal size), top and bottom cable entry with proper size glands including disconnecting cable connections and electronic meters from old meter cabin panel and fixing & connecting in new installed panel with provisions of thimble/lugs and making provisions of vision glasses for meter readings, one spare MCCB compartment, and including PCC on 1:2:4 type B-1 for fixing meter cabin at old meter cabin place complete all as specified and as directed by Engineer-in-Charge comprising of the following :-

(a) MCCB 100A, 4 pole, 415 volt, thermal magnatic release type, Ics=100% Icu, 25 kA - 01 Nos, Cat No-4200 55 of Make-Legrand/Siemens/L&T/Schneider. (b) MCCB 63A, 4 pole, 415 volt, thermal magnatic release type, Ics=100% Icu, 25 kA-02 Nos, Cat No-4200 53 of Make-Legrand/Siemens/L&T/Schneider. (c) MCB SPN 32 Amps- 10 Nos Make-Legrand Cat No-4086 17 or eqivalent to L&T/Schnider/ABB. (d) Smart Single Phase Meter tamper proof, static meter of Class 1.0, 240 V, 50 Hz, 10 A-60 A conforming to IS-16444. Make-L&T/HPLor as approved by GE (e) Digital panel meter with LCD multifunction meter with CT/PT and all parameters as V, A, F, PF, KW, kVAR, kWH etc of make :- L&T, Cat Ref -WL441010OOOO-01 set or equivalent in Legrand/Schnieder/ABB. (f) Phase indicator lamp R,Y & B - (01 Set of three). (g) Copper Bus bar, 200 Amps Rated - R,Y,B & N - (01Set of four). (h) Reconnecting of submain cable 2 core 4/ 6 Sqmm copper conductor with outgoing of energy meter. (j) Making good the disturbed surface of meter cabin room if any damages occures during shifting of panel. Note :- Before fabrication of panel the contractor has to take approval from accepting officer on drawing.

All as per Item No-197 here in before but comprising of the following items inside meter panel :- (Loc- Left and Right wing of AG2, AZ2, AE2 & AF2)

(a) MCCB 63A, 4 pole, 415 volt, thermal magnatic release type, Ics=100% Icu, 25 kA-02 Nos, Cat No-4200 53 of Make-Legrand/Siemens/L&T/Schneider (b) MCB SPN 32 Amps- 10 Nos Make-Legrand Cat No-4086 17 or eqivalent to L&T/Schnider/ABB (c) Smart Single Phase Meter tamper proof, static meter of Class 1.0, 240 V, 50 Hz, 10 A-60 A conforming to IS-16444. Make-L&T/HPLor other equivelent (d) Digital panel meter with LCD multifunction meter with CT/PT and all parameters as V, A, F, PF, KW, kVAR, kWH etc. (e) Phase indicator lamp R,Y & B - (01 Set of three). (f) Copper Bus bar, 100 Amps Rated - R,Y,B & N - (01Set of four). (g) Reconnecting of submain cable 2 core 4/ 6 Sqmm copper conductor with outgoing of energy meter. (h) Making good the disturbed surface of meter cabin room if any damages occures during shifting of panel. Note :- Before fabrication of panel the contractor has to take approval from accepting officer on drawing.

Material and labour for earthing complete with galvanized steel earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth strip 32 X 6mm by means of bolts, nuts and washers of galvanized iron or steel upto the test point all as shown in electrical plate No.3 of SSR Part-I connected toExisting earth strip including PCC earth pit with CI cover, GI funnel with wire mesh, GI protection pipe of 40 mm dia for earth lead and 20mm GI pipe for watering, excavation and earth work in any type of soil, filling the pit with charcoal and common salt surrounding the earth plate complete all as specified and as directed by Engineer-in-Charge including testing on completion.

Supply and fixing junction box of size not less than 4x4 inch with connector encloser, 3 terminal/ PVC/ polycarbonate, isolated body including taking out old one complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement with LED 45 Watts street light in pressure die cast aluminium housing with toughened glass and high power LED's with secondary optics and IP66 protection, aerodynamically designed for all weather conditions with excellent thermal management having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07, efficacy ≥ 110LPW alongwith 10KV SPD with including connecting light with three core copper wire from connector or ceiling rose complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing street light bracket bend to shape made as required of 25mm dia, GI pipe light grade fixed to pole/ Wall including Material and labour for fixing with the help of flat iron clamp with the help of nuts and bolts for fixing of street light fitting on the wall complete after taking out old Unserviceable one complete all as specified and as directed by Engineer-in-Charge.

Supplying and laying with commissioning and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of size 50 sqmm 3.5 core laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles and taking out old u/s damaged cables complete all as specified and as directed by Engineer-in-Charge. Make: Polycab/Havells/Gloster/KEI

All as per Item No-203.00 here in before but of sizes, 35 sqmm, 3.5 core complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm dia High density poly-ethylene pipes (HDPE) of pressure 6 kgf/cm2 pipe, for road crossing of cable or for cable protection laid in trenches or above ground surface complete all as specified and as directed by Engineer-in-Charge.

Supply and fix digital time switch 3 phase of current capacity 16 amps incl any type of accessories with suitable capacity of contractr complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5 mtr wide and not exc1.5 mtr in depth for laying of cables etc. in any type of soil and getting out all as specified and directed by Engineer-in-Charge. Note : Rate includes removing of paver blocks carefully and stack properly for refixing after laying of cables . complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing on wall/ laying in trench 6 x 1.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable complete all as specified and directed by Engineer In charge.

Supply & fixing on wall/ laying in trench 5 pair 0.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable complete all as specified and directed by Engineer In charge.

Cutting existing road surfaces or hard standing 0.45 mtr depth (22 thick comprising bituminuous topping) for laying of pipes/cables and making good disturbed surfaces to match with existing surfaces complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in replacement of shower rose CP 125mm dia swivel type suitable for 15mm bore CPVC tubing complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of air Shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour.(Minimum weight 40gms) complete all as specified and directed by Engineer In charge.

Removing excavated material exc 150 M but n.exc 500 M and depositing where complete all as specified and as directed by Engineer-in-Charge.

Material and labour cement concrete 1:2:4, type B-2 (using 40 mm graded stone aggregate) as, foundation and on road cutting hardstanding finishing even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Cutting/demolition of cement concrete(un reinforced) /bitumen road n.exc 15 cm thickness (below or above ground level) and remove debris out side MD land complete all as specified and as directed by Engineer-in-Charge.

Supply and laying in replacement of spigot and socket ductile iron water tubing,class K-9, cement mortar lining on inner surface and one coat of bituminous paint over exposed surface ISI marked, IS No. 8329: 2000, including rubber joint of suitable size laid on roof/floor/trenches with proper alignment as per site requirement and carryout testing against leakage before filling the trenches etc complete all as specified and as directed by Engineer-in-Charge..

150mm bore

100mm bore

Supply and fixing in repair in Sluice valves flanged end, cast iron body, flanged and drilled and non rising type stainless steel spindle with nut, long body, class P N 1.6, conforming to IS 14846 of 2000 for following sizes in any position/location including all flange joint with rubber or fiber board gaskets, bolts, nuts and washers complete including pumping out accumulated water all as specified and directed of following sizes :- Note :- (a) For Additional manpower, welding, chipping, plastering and any other item required for replacement of the item including making good the disturbed surfaces are deemed to be including in the item rate and no extra payment will be claimed by the contractor to the work.

150 mm bore

100 mm bore

80 mm bore

Material and labour for 15mm thick full body vitrified tiles (stepping stone) of approved coloured with bull nosing and embossed tread lines (square / rectangular) area of each tile not less than area of each tread and risers of steps in stair case and landing area etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including bedding layer of 20mm thick using factory manufactured pre mix / ready mix mortar C:S :: 1:4 for laying floor finishes. complete all as specified and directed by Engr-in-Charge. Note : tech features of tiles should be : I) Deep Abrasion resistant : < 120 mm3, II) Scratch resistant – moh : > 6 III) Breaking strength n : >3500n IV) Flexural strength (n/MM2) : > 38 V) Water absorption : < 0.05% complete all as specified and as directed by Engineer-in-Charge.

Material and labour for CI/DI specials conforming to IS - 1538 & 9523 , spigot /socket or flanged fitting I.e. bend, tee, collar, flanged/ socket /spigot, Tappers and tails pieces etc suitable for 80/100/150/200/250/300 mm bore pipes (joints and joining material shall be measured and paid seperately) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for run lead joint in repair with pig lead including pumping out / bail out water and necessary excavation and earth work in any type of soil,to repair the joints for following sizes of pipes complete all as specified and as directed by Engineer-in-Charge. :-

150 mm bore

80/100 mm bore

Material and labour for Cutting existing DI/cast iron pipes and reducing for insertion of CI fittings to required length in position for following sizes :- Note :- Pipe fittings used shall be measured and paid under relevant items of schedule 'A' remaining items like welding and other items required shall be deemed to be included in the item rate complete all as specified and as directed by Engineer-in-Charge.

150 mm bore

80/100 mm bore

Construction of brick masonery valve chamber in repair of size 1.2 x 1.2 x 1.2 M (internal dimension) (above GL 0.30 mtr) suitable for fixing of sluice valves, 15cm thick foundation using PCC 1:4:8 type D-2 over 15cm thick hardcore of broken stone, 23cm thick brick walls built in cement and sand mortar 1:4, 15mm thick internal and external plaster including top of floor in cement and sand mortar 1:3, 15mm thick, finished even and smooth, without using extra cement, 10 mm thick plate cover on 80mm x 80mm x 8 mm MS angle frame embeded in PCC 1:2:4 type B-1coping, having rectangular, hinged, opening of size 150 x 100mm with locking arrangements ,hold fasts, etc, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repairs 3- layer PP-R Polypropylene random copolymer) concealed pipes 90 mm outer dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches. complete all as specified and as directed by Engineer-in-Charge.

Taking down of old pipe lines of 50 to 100 mm dia of any nature complete all as specified and as directed by Engineer-in-Charge.

Taking down of old pipe lines of 150 mm dia of any nature complete all as specified and as directed by Engineer-in-Charge.

Taking down old unserviceable valves of 80/100 mm dia of any nature complete all as specified and as directed by Engineer-in-Charge.

Taking down old unserviceable valves of 150 mm dia of any nature complete all as specified and as directed by Engineer-in-Charge.

Supply, Installation Testing & Commissioning of Indoor type Programmable Logic Controller based Valve Automation and communication Panel suitable for control and/or monitoring of 09 Nos motorized valves and 12 Nos. magnetic sensors. The panel should be of suitable size fabricated from 2.0 mm thick CRCA sheet and properly powder coated. The Panel should have the following features :-

Automatic Operation of Motor Actuated Valves The PLC based Panel shall consist of the following sub systems (a) 01 No PLC with following specifications: (i) 30 Nos Digital inputs, 18 digital outputs (ii) 4 serial ports supporting open communication protocol, 01 No. Ethernet port (iii) Programming software based on IEC to facilitate building of custom built function blocks (iv) Expandable upto 192 DI / DOs

01 No. SMPS of 5 A rating

Suitable Nos. of interposing relays 24 V D.C. coil rating, 4 pole and 2 A contact rating

MCB of rating 6A, 10KA, 'C' series

Redundant GPRS modem based communication module comprising of one Main and One standby Modem with suitable antenna, modem controller and 02 Nos data eabled SIM cards.

SITC of rack mountable web smart switch with 28 ports and POE for CPE hardware--1 Each and following specifications: (a) Number of Ports 24 10/100Base-TX Ethernet ports 2, 10/100/1000BASE-T 2 Combo 10/100/1000BASE-T/SFP ii) Port StandardSupply and fixing unctions • IEEE 802.3 10BASE-T Ethernet (twisted-pair copper) • IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted-pair copper) • IEEE 802.3x Flow Control • IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper) • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 Switching Capacity • 12.8 Gbps

Hot pluggable 1310 nm multimode/Single mode SFP (mini-GBIC) transceiver, supporting full duplex, Gigabit speeds on multimode/Single mode fiber for distances of up to 550m/550m/10km on 62.5µm/50µm/ 9µm respectively in a metal housing to reduce EMI and to increase durability-2 Each

Rack Mountable LIU -1 Each with the following specifications (a) Rack Mountable 12 Port Unloaded LIU (i) Aluminium Base Material (ii) Slim 1 U mounting height (iii) Metal Shelf Aluminium 1.2 mm thick (iv) Splice tray Aluminium 0.6mm (v) Winding Panel – Plastic (vi) Cable Plug – Rubber for minimum 2 cable entries (vii) Adaptor Panel Aluminium 1.5 mm thick (viii) 2 fiber spools built in for 900 um tight buffered fibre storing (ix) Capable of storing upto 3 mts of 900 um tight buffered fibre per adaptor

SC-LC Duplex SM Patch Cord 0.9 mm dia of suitable length-6 Each (a) Size 0.9mm dia (b) Insertion Loss <=0.2 db, max 0.3 db (c) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (d) Connector Ferrule Ceramic (e) Apex Offset <50um (f) Fiber Height +-100nm (g) End Face Radius of Curvature 7mm<R<25mm (h) Repeatability <=0.2 dB 1,000 times mating cycles (i) Working Temp -40deg C to +85 deg C

CAT6 UTP 24 AWG Patch Cord of suitable length, Plug 30U snag less -2 Each.

CAT 6 UTP cable on walls -1RMs

SC-SM-Simplex Pigtail of suitable length-8 Each (a) Insertion Loss <=0.2 db, max 0.3 db (b) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (c) Connector Ferrule Ceramic (d) Apex Offset <50um (e) Fiber Height +-100nm (f) End Face Radius of Curvature 7mm<R<25mm (g) Repeatability <=0.2 dB 1,000 times mating cycles (h) Working Temp - 40deg C to +85 deg C

SC Simplex Coupler/Adaptor-4 Each (a) Insertion Loss <=0.2 dB for Zirconia Sleeve (b) Sleeve/Ferrule Withdrawl Force 2.0N to 5.9N

Integration of Existing SCADA System SCADA Configuration: (a) Addition of required OPC Server tags. (b) Addition of required SCADA Tags (c) Addition of required Data log Module. (d) Addition of required App Module (e) Addition of required Reporting & SMS Utility

Development: (a) SCADA Screens for new Updated Panel configuration. (b) Layout for App new Updated Panel configuration. (c) Report Format new Updated Panel configuration

Integration of OPC Sever with SCADA: (a) Tags binding – OPC to SCADA, (b) Tags binding – SCADA to Screen Objects (c) Tags binding – Data log module (d) Tags binding – SCADA to App (e) Tags binding – SCADA to Reporting Software. (f) Tags binding – SCADA to SMS Utility Software

On site development: (a) Modifications in SCADA Screens. (b) Modifications in reporting format (c) Modifications in App layout Make of Control Panel: Cimcon Software Pvt Ltd/ Reckronic Devices and Systems / Sombansi Enviro Engg Pvt Ltd/ Siemens/ NOTE:Quoted rate should include splicing,OTDR tracing Test cost

Supply and fixng in repair PVC water storage Tank 5000 ltr capacity 2 layers , ISI marked Pure antimicrobial round type, White colour, hosting and fixing in position at any location removing existing tank disconnecting all incoming & out going connection , provision of new tank fittings & connecting it at existing position up to 50 mm GI Pipe connection including replacement of tank nipples, GI union and GI fittings as required at site, new 40 mm Float valve with complete fitting , provision of PCC blocks under the delivery line on roof complete all as specified and directed complete all as specified and directed by Engineer In charge.

Supply and fixng in repair PVC water storage Tank 2000 ltr capacity 2 layers , ISI marked Pure antimicrobial round type, Green colour, hosting and fixing in position at any location including PCC foundation not less than 30 Cm above on roof ,removing existing tank disconnecting all incoming & out going connection , provision of new tank fittings & connecting it at existing position up to 50 mm GI Pipe connection including replacement of tank nipples, GI union and GI fittings as required at site, new 25 mm Float valve with complete fitting, provision of PCC blocks under the delivery line on roof complete all as specified and directed by Engineer In charge.

Supply/Fixing in repair/replacement of steel water tubing, galvanised, Medium grade of size 50 mm dia with all fittings in shafts such as nipple, union, socket, elbow, bends, fixed to wall including necessary GI/MS clamps in intervals of not exceeding 90 cm length complete all as specified and directed by Engineer In charge. Note :- Supply and fixing of one GI Union in raising main and one in delivery lines are mandatory and are included in the item rate.

Supplying and laying of CPVC pipes 32 mm outer dia (Inner dia 25 mm) SDR 11 & Plain CPVC SDR 11 fittings complete all as specified. Note :- Supply and fixing of one CPVC Union in each delivery lines are mandatory and are included in the item rate.

Supplying and laying of CPVC pipes 25 mm outer dia (Inner dia 20 mm) SDR 11 & Plain CPVC SDR 11 fittings complete all as specified and directed by Engineer In charge.

Supplying and laying of CPVC pipes 20 mm outer dia (Inner dia 15 mm) SDR 11 & Plain CPVC SDR 11 fittings complete all as specified and directed by Engineer In charge. Note :- Supply and fixing of one CPVC Union in each Inlet and one in out let of Loft tanks to be fitted in bathroom/kitchen are mandatory and are included in the item rate.

Supply and fixing in repairs 3- layer PP-R Polypropylene random copolymer) pipes 40 mm outer dia (Green colour) SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed on wall with the help of GI/MS clamps in intervals of not exceeding 90 cm length complete all as specified and directed by Engineer In charge. Note :- Supply and fixing of one PPR Union in raising main and one in delivery lines are mandatory and are included in the item rate.

Supply and fixing in repairs 3- layer PP-R Polypropylene random copolymer) pipes 32 mm outer dia (Green colour) SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed on wall with the help of GI/MS clamps in intervals of not exceeding 90 cm length complete all as specified and directed by Engineer In charge. Note :- Supply and fixing of one PPR Union in each delivery lines are mandatory and are included in the item rate.

Supply and fixing in repairs 3- layer PP-R Polypropylene random copolymer) pipes 25 mm outer dia (Green colour) SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed on wall with the help of GI/MS clamps in intervals of not exceeding 90 cm length complete all as specified and directed by Engineer In charge. Note :- Supply and fixing of one PPR Union in each delivery lines is mandatory and is included in the item rate.

Supply and fixing in repairs 3- layer PP-R Polypropylene random copolymer) pipes 20 mm outer dia (Green colour) SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings fixed on wall with the help of GI/MS clamps in intervals of not exceeding 90 cm length complete all as specified and directed by Engineer In charge. Note :- Supply and fixing of one PPR Union in each toilet connection in out side building is mandatory and included in the item rate.

Supply and fix in replacement of brass gate valves 15 mm , with iron wheel head, screwed both ends for iron/CPVC pipe and fixed complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of brass gate valves 40 mm , with iron wheel head, screwed both ends for iron/CPVC pipe and fixed complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of brass gate valves 50 mm , with iron wheel head, screwed both ends for iron/ CPVC pipe and fixed complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of Stop valves 15 mm bore, fancy type, chromium plated (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron/CPVC pipe or for unions and fixed complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of Stop valves 15 mm bore, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron/CPVC pipe or for unions and fixed complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of Fancy type Bib taps Chromium plated 15 mm bore surface fixing, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer In charge.

Supply & fixing PVC loft tank (LDPE) of capacity 275 ltrs, ISI marked, Company name embossing/Painting on tank with complete fitting including 03 Nos adopter with washer for inlet/outlet,over flow as per manufactureres instructions complete including brass float valve (ISI marked) high pressure with polythelene float (flat) and fly nut complete screwed for CPVC pipe 15mm bore all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC profile suitable for 275 ltrs loft tank including fixing of aluminium channel around the profile complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of Fancy type Bib taps Chromium plated 15 mm bore suitable for washing machine surface fixing, cast copper alloy with crutch or butterfly handle, screwed down, screwed for CPVC/iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer In charge.

Supply and fix in replacement of Fancy type Bib tap 2-way Chromium plated 15 mm bore surface fixing, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer In charge.

Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections/ladders for over head tanks/base supporting of loft tanks including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed by Engineer In charge.

Supply, Installation in repair, Testing and Commissioning of Float type Point Level Sensor with the following specifications; Type: Magnetic, Magnet: Ring type, Switch: Reed Switch (Epoxy sealed) complete all as specified and directed by Engineer In charge. Connecting Cable: Teflon

Supply, Installation in repair, Testing & Commissioning of Motor Actuated Ball Valve consisiting of suitable single phase Actuator and ball valve of size 50 mm dia with appropriate bracket/mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure complete all as specified and directed by Engineer In charge. Specifications & Features Input Voltage: 230 V, A.C. Designed line pressure: 10 kg/sq cm. Material of Ball: Stainless Steel Limit Switches : 02 Nos.For open and close status Mounting :Direct on valve Make: RITETORK /Universal Switch gear/Marsh

Supply, Installation, Testing and Commissioning of Optical Fiber cable to be pulled over head and duly fastened/attached to a messenger wire or a stay wire of gauge either with the required clamps of suitable size not more than 3 feet apart or with a web between the OFC and messenger wire along with endplates at both ends of the suspended cable complete all as specified and directed by Engineer In charge. (a) 6F Single mode OFC suitable for outdoor networking applications (i) 6 Fibers type single mode, wavelength 1310, Attenuation 0.38/km (ii) Outer jacket of HDPE sheath (iii) Jelly Filled Core (iv) Wrapped with Corrugated Steel Tape (v) Armoured with a pair of Steel Wire for rigidity (vi) Anti Termite and rodent repellent (vii) Water Proof and moisture resistant

Material and labour for earthing complete with galvanized earth plate 60cm x 60cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below normal ground level connecting with 25 x 4 mm GI strip by means of bolts nuts, check nuts and washers of galvanized iron all shown in electrical plate No 03 of SSR Part-I including necessary excavation earth work using PCC 1:2:4 for earthing pit and pit cover with handle of 8mm dia MS rod and connected to test point complete all as specified and directed by Engineer In charge. Note : (a) The item rate inclusive of fixing of earth continuity conductor from earth plate upto 7.5 mtr. (b) The item rate inclusive of provisioning necessary charcoal and salt upto the level of the earth plate in alternate layers.

Earth continuity conductor or main earthing lead fixed to wall on FRP insulators or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 x4 mm galvanised iron or steel strip complete all as specified and directed by Engineer In charge.

Taking down carefully of SCADA control panel-01 No. , motorised valves-06 Nos, magnetic sensors- 12 Nos and cables before starting the special repair work , kept in safe custody without any damage and refixing as per previous location, fixing of cables with saddles and testing after completion of special repair work at site complete all as specified and directed by Engineer In charge. Note :- Any damaged/malfunctioning of SCADA items/panels at the time of removing/refixing shall be the Contractors responsibility and no extra cost will be given to the contractor for make it serviceable at site.

Garima Construction Co

Shree Ayyappa Engineering

SANKALP INFRACON