GE/U(N)-69/2019-20 SPECIAL REPAIR TO LADIES AND GENTS TOILETS BLOCK NEAR BLDG NO NP-15 AND SPL REPAIR TO PATH AT REAR SIDE BLDG NO P-30 TO TABLE TENNIS COURT AND PROVN OF TILING IN CERTAIN QTRS AT PB ENCLAVE OF GE NORTH UDHAMPUR

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground), complete all as specified and directed by Engineer-in-Charge.

Dismantling cast iron or reinforced concrete drain pipes, any size up to 100mm bore, jointed in in cement mortor and taking out of trenches if required, complete all as specified and as directed.

Dismantling of structural steel work in any description complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches,pillars,etc,but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided and removing the demolished material from side, complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, heart or wall tiling including Cement Mortar bedding(but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engineer-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5sqm but not exc 4 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Refixing door shutter of any description exc 1.00 Sqm and not exc 2.00 Sqm each in same opening after taking down,easing and adjusting and also refixing builders hardware as required; complete all as specified and directed.

Taking up or down steel tubing and connection, including cleaning for re-fixing or removal to store of size of pipe 15 mm bore laid on floor or wall, complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection, including cleaning for refixing or removal to store of size of pipe 25 mm bore laid on floor or wall, complete all as specified and directed by Engineer-in-Charge.

Brick work with subclass ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6), complete all as specified and directed by Engineer-in-Charge..

Brick work using old size bricks (EXCEPT BRICKS) straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar (1:6), complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class B old size bricks straight or curved on plan any radius in half bricks thick wall built in cement mortar 1:4, complete all as specified and directed by Engineer-in-Charge..

Providing Precast Cement concrete 1:2:4 type B-0 ( Using 12.5 mm graded crushed stone aggregate ) in road side kerb stone etc (of any section indicated) with plain fair faces, including chamfers, weathering, throating etc and setting in cement mortar 1:4 complete with joints to match as directed by Engr-in-Charge.

Cement concrete 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, steps, seismic and other similar bands coping/cills/benching,bed plates bed block etc for embedding hold fast including necessary form work weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

Reinforced cement concrete 1:1 ½ : 3 type A-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies deck slabs, and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

Use & waste of form work to edges of concrete flats, treads, breaks in floors, window cills, floor and roof slabs and shelves, horizontal or sloping and similar work etc thickness exc. 5cm but n.exc 10 cm for flat fair finished surface complete all as specified and directed by Engineer-in-Charge.

Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landing horizontal or slopping similar work not. Exc 200mm thick, and flat fair finished surfaces complete all as specified and directed by Engineer-in-Charge.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-Charge.

1.60mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed by Engineer-in-Charge.

Rolled mild steel section of angle, tee, flats,and plates as in roof trusses, purlines, rails, etc and the like fixed with angle cleats and connecting plates including welding,Gde FE-410-0 or FE-310-0 , complete all as specified and directed by Engineer-in-Charge.

Nails of 50mm to 80mm in length fixed with welding to MS sheet, complete all as specified and as directed by Engr-in-charge.

Aluminium door shutters/ sliding partitions with chowkhat of powder coated, with aluminium section weighing not less than 1.5 kg/m, powder coated of any colour (thickness or powder coating not less than 50 micron), including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, mortice locking arrangement, hinges, 2Nos tower bolt anodised aluminum snap beading screws etc.; panelled (two panels), filled with 5mm thick PVC sheet manufactured by Rajshree Indore or equivalent or 5.0mm thick frosted glass; fitted with rollers, bottom and upper guide channels, complete all as specified complete all as specified and as directed by Engr-in-Charge.

Aluminium sliding window, ventilator shutter with chowkhat of powder coated, 5mm thick glass, stainless steel wire gauge for shutters, etc, without sash bars, aluminium sections weighing not less than 0.55 kg/m (thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 5mm thick tinted glass, stainlee steel wire gauge for shutter three track (02 Nos shutter glazed & 01 No wire gauge) etc, complete all as specified and as directed by Engr-in-Charge.

25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, finished rough, as in floors base of tiles, complete all as specified and directed by Engineer-in-Charge.

Plinth protection 50 mm thick in PCC 1:3:6, type C-1 ( using 20 mm graded crushed stone aggregate ) laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth without using extra cement and providing joints through out the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and as directed by Engr-in-Charge.

Plain Cement concrete 75mm thick 1:4:8 type D2 using 40mm graded stone aggregate as in sub base to floors finished even and rough complete all as specified and directed by Engineer-in-Charge.

Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including laying of 10 mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic double charged light shade coloured tiles 9-10mm thick (Square/rectangular) polished area of each tile exceeding 0.64 Sqm but not exceeding 1 Sqm, laid in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed 10mm thick in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge

Vitrified ceramic light shade coloured tiles 9-10mm thick (Square/rectangular) polished area of each tile exceeding 0.72 Sqm but not exceeding 1 Sqm, on vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic tiles size 450 mm x 300 mm x 7to8mm thick on vertical surfaces such as skirting /dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing coat complete all as specified and directed by Engineer-in-Charge. Note:-Junction of floor and dado to be sealed with silicon sealent and rates of the same also inclusive of the same in the item.

Factory made, heavy duty full body digital, paving coloured tiles of size 300x300x10mm thick for external use and including jointing with spacers with neat cement slurry and pointed in coloured epoxy tile grout to match the shade of tile laid over and including screed bed 15mm thick in cement mortar 1:4 , complete all as specified and directed by Engineer-in-Charge. Make:-Durastone of somany/Pavigres of Kajaria/Endura of Johnson

Granite work with 16 to 18mm thick slab, table rubbed and polished, in steps, window cills, cooking platforms and like in single piece set in neat cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cement mortor (1:4) including dismantling of existing slab, complete all as specified and directed by Engineer-in-Charge.

Moulding on sides of granite slabs 16-18mm thick complete, complete all as specified and directed by Engineer-in-Charge.

15mm thick rendering on fair faces of brick work or concrete surface in CM 1:6 finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Rendering 5 mm thick plaster in CM 1:3 on ceiling surface finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:4), including integral liquid WPC by wt of cement as per manufacturer instruction (NOTE : Supply only WPC will be measured and paid for separately), complete all as specified and directed by Engr-in-charge.

Preparing of new plastered or un-decorated surfaces applying two coats of distemper oil emulsion over including one coat 1 to 1.20mm thick wall care putty on wall surfaces, complete all as specified and directed by Engineer In Charge

Preparing of new plastered or un-decorated surfaces applying two coats of distemper oil emulsion over including one coat 1 to 1.20mm thick wall care putty on ceiling surfaces, complete all as specified and directed by Engineer In Charge

Prepration of new plaster surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant cement base primer on wall surfaces, complete all as specified and directed by Engineer In Charge

Preparation of new concrete surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of primer, complete all as specified and directed by Engineer-in-Charge.

Preparation of old plastered or un-plastered surface and applying one coat of distemper oil emulsion white or tinted, complete all as specified and directed by Engineer In Charge

Complete removal of existing treatment on walls surfaces by brooming down or steel wire brushing,scraping down smoke soot, moulds moss and efflorences salts and trading oil and greasy spots and applying two coat of distemper oil emulsion white or tinted over including one coat 1 to 1.20mm thick wall care putty, complete all as specified and directed by Engineer In Charge

Complete removal of existing treatment on ceiling surfaces by brooming down or steel wire brushing,scraping down smoke soot, moulds moss and efflorences salts and trading oil and greasy spots and applying two coat of distemper oil emulsion white or tinted over including one coat 1 to 1.20mm thick wall care putty, complete all as specified and directed by Engineer In Charge

Complete removal of existing treatment on walls surfaces by brooming down or steel wire brushing,scraping down smoke soot, moulds moss and efflorences salts and trading oil and greasy spots and applying two coats of cement based paint, complete all as specified and directed by Engineer In Charge

Vitreous china wash down water closet (pedestal pattern) white complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc, fixed in repair, complete all as specified and as directed. Make-CERA cat part No. S1050101/02, Jaquar –CNS-WHT-WH 10 or equivalent make as per PS

Plastic water closet seat, closet pattern with flat bottom and cover and incl mild steel chromium plated or aluminum hinges device complete fixed in repairs , all as specified. Make-CERA cat part No. B1510121, Jaquar –CNS-WHT-WCS 1 or equivalent make as per PS

Vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests including replacement of 'P' or 'S' CI trap, lime concrete bedding and making good existing floor fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Vitreous China urinals, pedestal type, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe)fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Urinal spreader of chromium plated for fixing with 15mm dia pipe. (Minimum weight 60gms)fixed in repair, complete all as specified and directed by Engineer-in-Charge.

10 ltrs PVC flushing cistern low level (white) with inlet, ball valve float and handle including PVC Connection and 32mm dia PVC long bend for squar pattern etc. set with concrete and making good to floor fixed in repair, complete all as specified and as directed by Engr-in-Charge.

Vitreous China wash basin, white, oval type, size 580x450mm (for Hospital use) excluding taps, waste, chain and plug and porcelain stopper but including brackets ,waste pipe fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Vitreous china,white, wash hand basin, flat back of size 550x400mm, white including MS brackets and pedestal pattern including cutting for and pinning including 32mm dia CP brass waste coupling and PVC waste pipe, fixed in repair complete all as specified.Make-CERA cat part No. S 2040105 for WHB & for pedestal cat part No.S 2090101, Jaquar- SLS-WHT-0611F for WHB and SLS-WHT-1510 for pedestal or equivalent make as per PS

20mm dia brass chromium plated tubular towel rails,D type,60 cm long between flanges Fixed in repair complete all as specified and as directed.Make -Jaquar cat part no. CAN-1111NM,Cera- F5007103 or equivalent make as per PS

Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, guard and railing 60cm long fixed in repair complete all as specified and as directed. Make -Jaquar cat part no. AKP-35771P, Cera-F 5001114 or equivalent make as per PS

Single lever wall mixer 3 in 1, with provn of over head shower & hand shower, telephonic type, brass, chromium plated, fancy type, with capstan head handles with lettered 'hot' and 'cold', screwed down high pressure, including CP brass wall flanges and necessary extension nipples screwed for 15mm bore pipe connection, with provision for both hand shower and over head shower, fixed in repair, complete all as specified and directed. Make : Jaquarcat part No. FUS-29281, Cera- F 2007403 or equivalent make as per PS

Centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, fixed in repair complete all as specified and directed. Make : Jaquar, Cat part No. SOL-6169B., Cera- cat No. QTF 2006461or equivalent make as per PS

Hand shower 90mm round shape (telephonic shower), chromium plated, with 1500mm long 15mm bore chrome finish flexible pipe with hook, fixed in repair complete all as specified and directed. Make: Jaquar-code HSH-1727,SHA-571, Cera-F 7030105 for hand shower & F 8070401 for flexible tube or equivalent make as per PS

Shower rose, brass, chromium plated, with CP arm 120mm dia with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe or union as in repair complete all as specified and directed. Make : Jaquar cat part No. OHS-1719, Cera- F 7040101 for arm & F 7020305 for shower rose or equivalent make as per PS

Angle valve, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed. Make : Jaquar cat part No- CON-053KN, Cera- QTF 2006201 or equivalent make as per PS

Bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed. Make : Jaquar cat part No.- CON-037KN, Cera-QTF 2006152 or equivalent make as per PS

Health faucet, brass, chromium plated, with 1000mm long 8mm dia chrome finish flexible pipe with wall hookfixed in repair, complete all as specified and directed by Engineer-in-Charge. Make - Jaquar cat part No- ALD-573, Cera- F 8030103 or equivalent make as per PS

PVC flexible connections 450mm long 15mm dia with brass flange nuts & washers fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make-Jaquar, cat part No. ALD-805B, Cera-CG 107 or equivalent make as per PS

PVC flexible connections 600mm long 15mm dia with brass flange nuts & washers fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make-Jaquar, cat part No. ALD-801B or equivalent make as per PS

Soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws, fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make: Jaquar-code F5004106,or equivalent make as per PS

Toilet paper holder, brass, chromium plated, heavy duty, fixed with brass screw fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make- Jaquar cat part No. ACN-1153N, Cera-F 5007109 or equivalent make as per PS

CP brass grating 100mm dia, centre hole, fixed in repair, complete all as specified and directed by Engineer-in-Charge.

CP brass grating 100mm dia,fixed in repair, complete all as specified and directed by Engineer-in-Charge.

CP Towel Ring 200mm dia fixed in repair complete all as specified and as directed by Engineer-in-Charge. Make-Jaquar, AQN-7721, cera - F5002105 or equivalent make as per PS

Gun-metal, globe or gate valves,20mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed in repair, complete all as specified and directed by Engineer-in-Charge.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints ,fixed to walls or as in floors, complete all as specified and directed by Engineer-in-Charge.

Cast iron nahani trap to 75mm bore including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Cast iron soil, sand cast waste and vent pipes,75mm dia in any length with or without ears with cement joints, laid in trenches or in floors fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Sand Cast iron soil, waste and vent pipes,75mm dia in any length with or without ears with cement joints, fixed to wall fixed in repair, complete all as specified and directed by Engineer-in-Charge.

75mm bore bends(any radius) with duck foot or heel rest fixed in repair, complete all as specified and directed by Engineer-in-Charge.

75mm bore bends/reducer (any radius) diminishing pieces or tapers (larger bore measured)fixed in repair, complete all as specified and directed by Engineer-in-Charge.

75mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Rotational moulded polythene water storage tanks 3 layer white colour (cylindered vertical closed top ) hoisted and fixed in position including necessary connection nipple suitable for inlet, outlet and overflow pipes, all as specified in SSR Part –I of capacity of tanks 1000 ltrs and including dismantling of existing unserviceable water tanks and remove from site, complete all as specified and as directed by Engr-in-Charge.

20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer-in-Charge.

15 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.),complete all as specified and as directed by Engr-in-Charge.

All as per Serial Item 84 here-in-before but except tubing (Old serviceable tubing as retrieved vide item above shall be reused under this item).

25 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.),complete all as specified and as directed by Engr-in-Charge.

Cutting chases, pining in, making good to facings where required and pointing in cement mortar 1:3, for concealed water tubing etc and maing good, cutting exc 10cm and not exc 20 cm girth complete all as specified and directed.

XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core in trenches/floor/pole/GI pipe complete including cutting of bituminous road/chasing to any surface and making good to the disturbed surface to match the existing including taking down of existing cable complete all as specified and directed by Engineer-in-Charge..

Excavation in trenches in any type of soil n.exc. 1.50m deep and n.exe 1.50 in wide and getting out in., complete all as specified and as directed by Engr-in-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and as directed by Engr-in-Charge.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point, complete all as specified and as directed by Engr-in-Charge.

Dry coarse sand as cushioning to under ground cable provided with layer of 8 cms deep before laying the cable and 15 cms deep after laying and stretching the cable and punned to 18 cm thick, complete all as specified and as directed by Engr-in-Charge. Note : Only punned thickness shall be measured for payment purpose

Precast RCC cable cover class V typ-1 flat size 250x150x40mm, complete all as specified and as directed.

GI tubes light grade 40 mm bore with all fitting/acessories for protection of cable on pole/wall and under road crossing including clamps, nut bolt etc and including sealing end of pipe with bituminous preformed wooden gutties complete all as specified and directed by engr-in-charge.

Taking down carefully the existing Copper/ aluminium point wiring of any size and capacity and type by disconnecting from the either terminals complete with switches, sockets,ceiling rose, regulators,bell etc by unscrewing and taken away from site complete including making good to disturb surface of walls, floors etc. Note : (i) Old dismanteled wiring and accessaries will be contractors property and credit will be charged against schedule of credit.

Point wiring concealed with 1.5 Sqmm copper conductor cable (multistrand) PVC insulated FRLS (unsheathed), drawing in and including PVC concealed conduit 20 mm dia,cutting chases wall & ceiling and making good to disrurbed surface of wall ,ceiling etc,having wall thickness not less than 1.50 mm with sunk cast iron/pressed steel terminal boxes made out of 1.2 mm thick sheet including one coat red oxide primer on internal and external surface covered with 3 mm thick hylam brand IS-2036 marked laminated sheet cover (for mounting switches, sockets, regulators etc), including 1.5 Sqmm PVC insulated (multistranded) FRLS copper conductor continuous earth wire for one light /Fan point/Exhaust fan controlled by one switch one way complete all as specified and directed.

All as per description of Serial item No 96.00 here-in-before but one 3 pin 5 Amp socket outlet on Independent board, complete all as specified and as directed by Engr-in-Charge.

All as per description of Serial item No 96.00 here-in-before but one 3 pin 5/15 Amp socket outlet on independent board with PVC insulated, unsheathed FRLS cable 2.5 Sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 1.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly complete, complete all as specified and as directed by Engr-in-Charge.

Modular switch one way 6 Amps 1 module type, suitable for 240 V, 50 Hz, AC supply fixed in replacement, complete all as specified and directed by Engr-in-charge.

Modular switch one way 16 Amps 1 module type, suitable for 240 V, 50 Hz, AC supply fixed in replacement, complete all as specified and directed by Engr-in-charge.

Modular socket 6 Amps 2/3 pin combined 2 module type, suitable for 240 V, 50 Hz, AC supply fixed in replacement, complete all as specified and directed by Engr-in-charge.

Modular socket 16 Amps 2/3 pin combined 2 module type, suitable for 240 V, 50 Hz, AC supply fixed in replacement, complete all as specified and directed by Engr-in-charge.

Modular metal flush box 6 module , complete all as specified and directed by Engr-in-charge.

Modular metal flush box 4 module , complete all as specified and directed by Engr-in-charge.

Modular metal flush box 3 module , complete all as specified and directed by Engr-in-charge.

Modular white cover plate with frame 6 module , complete all as specified and directed by Engr-in-charge.

Modular white cover plate with frame 4 module , complete all as specified and directed by Engr-in-charge.

Modular white cover plate with frame 3 module , complete all as specified and directed by Engr-in-charge.

Ceiling rose surface backlite 65 x 20mm size three terminal fixed in replacement, complete all as specified and directed by Engr-in-charge.

New generation energy saving 9/10 watt LED bulk head with opal diffuser suitable for 600 Lumen fixed in replacement, complete all as specified and directed by Engr-in-charge. Make-Syska ordering code No-SSK-BH-9W/Havells cat part no-LHEXCGP7PN5W010 /Wipro,Product code no -D531065

Decorative ultra slim linear LED lighting fixture 18/20 watt LED battern, with full base of extruded aluminium section acting as a heat shrink with closed back, isolated driver, complete making all connection using 1.0 sqmm copper conductor multistranded PVC insulated 2 core flexible cable from ceiling rose to fitting in white colour fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make of LED- Havells cat part no. LHEXCEP7UN1W020/SYSKA cat part no SSK-RA1801 or equivalent of make Wipro

Taking down ceiling fan/exhaust fan any type and any sweep and removing fan blade including cleaning all dust particle and filling cavities with filler materials, oiling, greasing including painting fan and blades complete with one coat of synthetic enamel white paint by spraying and writting Ser No/MES No with black paint complete and assemble the same along with all fixing connecting accessories and fixing in same position along with all new electric wire connection from ceiling rose to fan, etc. complete, all as specified and as directed by Engineer-in-Charge.

Single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 4 ways fixed in repair, complete all as specified and directed by Engineer-in-Charge. Make:- Legrand(Ekinox3) or equivalent of make schneider(Acti-9)/Siemens(Betagard-8GB 32).

MCB SP 6 to 32 Amp, 240 volts, 50Hz, C series of breaking capacity 10 KA fixed in repair, complete all as specified and directed by Engineer-in-Charge.. Make :Legrand Product code no-408587/408590/408592/408593/408594 or equivalent in Schinder/Seimens.

MCB SPN, 6 to 32 Amps, 415 Volts, rupturing capacity 10 KA "C" Series, fixed in repair, complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 4 mm dia galvanised earth lead wire by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel all as specified or indicated in electrical plate no 3 of MES Part-I, fixed in replacement, complete all as specified and directed by Engr-in-charge. Including testing on completion including the material and labour of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. (e) 15 mm nominal bore light grade GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note : (a) On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge. (b) The contractor shall quote his rate considering taking down cost of existing unserviceable earthing.

anil construction co.

JOGINDER SINGH