Repair Renovation of Govt Industrial Traning institute (ITI) Bassi Pathana Distt Fatehgarh sahib

Laying and Jointing PVC Pipe. Heading

Dismantling roofing First class mud roofing

Stripping and stacking slate or tiles of a roof

Dismantling concrete Reinforced cement concrete

RemovingDoorsandWindows(Steelorwood) with chowkhats bymaking recesses inwalls when the wall is not to be dismantled

Windows of area 3 sqm and below

Doors of area 3 sqm and below.

Scraping cement plaster

SCRAPING White wash and colour wash

Dismantling brick work tile, masonry or tile lining In cement

Credit of old Brick recovered from dismanlting

i) Brick Bat

ii) Bricks

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concretemixer asper IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

Extra for R.C.C/PCC. work done in each subsequent storey above the first storey upto height of 4 metres or part thereof up to the roof top level of that storey.

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS1786-2008) , for R.C.C works,where not including in the complete rate of RCC including bending and binding placing in position complete

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels.

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Extra rate for shuttering ineachsubsequent storeyabove the first Storey work done in subsequent storey above the first storey up to height of 4 metres or part there of up to the roof top level of that storey.

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25mm mud plaster7.5cm mud filling on another layer of 25mm mudplaster including two coats of bitumen laid hot at 1.65Kg. /Sqmtopof R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing

12.5 mm thick cement plaster 1:4

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacemetc. Two or more coats to give an even shade.

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concrete 1:8:16 including 12.5 mm thick cement plaster 1:3

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes single socketed (working pressure 4 kgf/cm2) conforming to IS : 4985, including fixing with MS clamps U-PVC pipes (working pressure 4.00 kg / sqcm) 110 mm dia.

Providing and fixing 110mm dia.U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.UPVC 110 mm bend

Providing and fixing 110 mm dia. U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend

Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard designlatest), including iron lugs (holdfasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower boltsand finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge. Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter

Factory manufactured solid flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position. (Code IS 2022-1(1999)). Commercial with elm or gurjan facing on both\ Sides with laminated core and lipped edges:- 35mm thick

providing and fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge, (Cost of Gasket /beading shall be paid as per respective item). Float glass panes of 5.5 mm thickness

Providing & fixing beeding 12mm x 12mm for fixed glass with ECO fixed gasket (EPDM)

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. panelled, glazed or glazed and panelled 35 mm thick

Wire gauge Hollock wood door shutter without springs housed in chowkhat. 35 mm thick

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppersandscrewetc. for these fittings (Excluding sliding bolt) For shutter area up to 0.50 sqm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodiccoating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250mm x 16mm

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. Complete I.S.I DesignationNo. III (sizeof door 851mm to 1000mm)

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work,metallic or plastered, concrete surface to give an even shade.

Wire gauge fixed on chowkats with 25 mm thick Red meranti Normal (15 to 16 kg per cft. Approx.) wood covermolding of full width

Credit of iron sheet chowkhats

Civil Works Hostel Block no 2

Dismantling roofing First class mud roofing

Stripping and stacking slate or tiles of a roof

Dismantling concrete. Reinforced cement concrete

Removing Doors and Windows(Steelorwood) with chowkhats bymaking recesses inwalls when the wall is not to be dismantled

Windows of area 3 sqm and below

Doors of area 3 sqm and below.

Scraping cement plaster

SCRAPING White wash and colour wash

Dismantling brick work tile, masonry or tile lining In cement

Credit of old Brick recovered from dismanltingi) I Brick Bat

ii) Bricks

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level.

Reinforced cement concrete M-20 mechanically batchmixed using batch type concretemixer asper IS:1791andvibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

Cold twisted detormed (Ribbed/ Tor steel)Bars (Fe 500 grade as per IS1786-2008) , for R.C.C works,where not including in the complete rate of RCC including bending and binding placing in position complete

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels.

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25mm mud plaster7.5cm mud filling on another layer of 25mm mudplaster including two coats of bitumen laid hot at 1.65Kg. /Sqmtopof R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing

12.5 mm thick cement plaster 1:4

Preparationof plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Distempering with Acrylic washable oil bound distemper (of approvedmanufacture) two or more coats over one priming coat to give an even shade

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacemetc. Two or more coats to give an even shade.

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concrete 1:8:16 including 12.5 mm thick cement plaster 1:3

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes single socketed (working pressure 4 kgf/cm2) conforming to IS : 4985, including fixing with MS clamps U-PVC pipes (working pressure 4.00 kg / sqcm) 110 mm dia.

Providing and fixing 110mm dia.U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend

Providing and fixing 110 mm dia. U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend

Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard designlatest), including iron lugs (holdfasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower boltsand finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter

Factory manufactured solid flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position. (Code IS 2022-1(1999)). Commercial with elm or gurjan facing on both\ Sides with laminated core and lipped edges:- 35mm thick

providing and fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge, (Cost of Gasket /beading shall be paid as per respective item). Float glass panes of 5.5 mm thickness

Providing & fixing beeding 12mm x 12mm for fixed glass with ECO fixed gasket (EPDM)

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position window grilll

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. panelled, glazed or glazed and panelled 35 mm thick

Wire gauge Hollock wood door shutter without springs housed in chowkhat. 35 mm thick

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppersandscrewetc. for these fittings (Excluding sliding bolt) For shutter area up to 0.50 sqm window area

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodiccoating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250mm x 16mm

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. Complete I.S.I DesignationNo. III (sizeof door 851mm to 1000mm)

Applying pink primer or aluminum priming coat on wood work including preparationof surface knotting and stopping etc.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work,metallic or plastered, concrete surface to give an even shade.

Wire gauge fixed on chowkats with 25 mm thick Red meranti Normal (15 to 16 kg per cft. Approx.) wood covermolding of full width

Credit of chowkhats

Civil Works admin Block and Workshop

Dismantling roofing First class mud roofing

Stripping and stacking slate or tiles of a roof

Dismantling concrete Reinforced cement concrete

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses inwalls when the wall is not to be dismantled Windows of area 3 sqm and below

Doors of area 3 sqm and below.

Dismantling asbestoscement celotax or other hardboard ceiling or partition walls including supporting timber

Scraping cement plaster

SCRAPING White wash and colour wash

Dismantling brick work tile, masonry or tile lining In cement

Credit of old Brick recovered from dismanlting i) Brick Bat

ii) Bricks

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level.

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25mm mud plaster7.5cm mud filling on another layer of 25mm mudplaster including two coats of bitumen laid hot at 1.65Kg. /Sqmtopof R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing

12.5 mm thick cement plaster 1:4

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Distempering with Acrylic washable oil bound distemper (of approvedmanufacture) two or more coats over one priming coat to give an even shade

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacemetc. Two or more coats to give an even shade.

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concrete 1:8:16 including 12.5 mm thick cement plaster 1:3

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4.00 kgf / cm²) conforming to IS: 4985, including jointing with seal ring (i) Single socketed pipes. U-PVC pipes (working pressure 4.00 kg / sqcm) Single socketed pipe 110 mm dia.

Providing and fixing 110mm dia.U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. UPVC 110 mm bend

Providing and fixing 110 mm dia. U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer - in- charge. UPVC 110 mm bend

Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard designlatest), including iron lugs (holdfasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower boltsand finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter

Factory manufactured solid flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position. (Code IS 2022-1(1999)). Commercial with elm or gurjan facing on both\ Sides with laminated core and lipped edges:- 35mm thick

Providing and fixing ( PPGL) precoated painted galvalume sheet roofing (size, shape and pitch of corrugation as approved by Engineer-in-charge) The end rib shall have anti cappillary groove and return leg. The steel sheet must be having yield strength of 550 MPa ( Fy= 550 MPa) metallic coated with Zinc- Aluminium alloy ( i.e. 55% Al, 43.4%Zinc, 1.6% Si-Zincalume) AZ150 ( Min. 150 bm/mm2 total on both sides), pre painted with super Durable Polyster XRW quality paint includes inorganic infrared reflective pigment. The sheet confirms to general requirement of AS/NZS 2728 type 4/ IS 15965 class 3 durability and gloss value of 25% -40%. should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required (Make JINDAL) 0.60 mm (+ 0.05 %) thick

Providing and Fixing of Heat Resistant Insulation sheet inside of PPGL Sheet for Heat insulation To the entire Satisfaction of Engineer in Charge.area as per above item in sqft.

providing and fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge, (Cost of Gasket /beading shall be paid as per respective item). Float glass panes of 5.5 mm thickness

Providing & fixing beeding 12mm x 12mm for fixed glass with ECO fixed gasket (EPDM)

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. panelled, glazed or glazed and panelled 35 mm thick

Wire gauge Hollock wood door shutter without springs housed in chowkhat. 35 mm thick

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt) For shutter area up to 0.50 sqm window area

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250mm x 16mm

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. Complete I.S.I DesignationNo. III (size of door 851mm to 1000mm)

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work,metallic or plastered,concrete surface to give an even shade.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Wire gauge fixed on chowkats with 25 mm thick Red meranti Normal (15 to 16 kg per cft. Approx.) wood covermolding of full width

Civil Works Outer Infrastructure Dismantling brick work tile, masonry or tile lining in cement

Credit of old Brick recovered from dismanlting i) Brick Bat

ii) Bricks

Construction for Boundary wall as per the design, drawing and specifications approved by Engineer-in-charge.

Providing and laying 60 mm thick factory made cement concrete interlocking Paving blocks of M 35 grade manufactured by block making machine equipped with steel mould clamped toa strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63-2014 and of approved size and design/ shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in- charge

Providing and laying factory made rubber moulded smooth finish cement concrete Kerb M-20 grade 250 mm high with bottom width 165 mm and top width 115 mm made over strong vibratory table and fixing with cement mortar1:2asperMORT&H specifications

Construction of granular sub-base by providing material, spreading inuniform layerswithmotor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desireddensity,complete as per MORD technical specifications

Wrought iron&Mild steel ladders, framed grills, gratings etc.with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position for sheds

Corrugated asbestos Sheet roofing 6 mm thick sheets fixed with G.I. hooks and bolts, limpet and bitumen washers complete fixed in position excluding the cost of perlins, rafters and trusses

Site clearance Surface dressing of ground including removing rank vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 mand lift up to 1.5 m in all kinds of soil.

Add Credit of Steel obtained form dismantling or Roof Slab of Hostel 1 Hostel 2 and admin Block and workshop

Public Health Works

Providing and fixing in position Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity (without cistern fitting) size 62x37x67 cm with P trap or S trap and seat cover complete in all respect.

Providing and fixing jet spray with 2'-6" long PVC pipe. With C.P. Brass nut

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect.Size 550mm x 400mm x 815mm

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge ) complete in all respect. C.P. Brass fittings:C.P.brass 15mm Angular stop cock with Wall flange

C.P. Brass Accessories: C.P. brass towel rail 600 mm long

C.P. brass soap dish holder with glass dish

C.P. brass toilet roll holder with flap

Providing and fixing in position Vitreous Chinaware white urinal with concealed or in built P-trap (size 310x370x640 mm) with built in water seal, outlet to wall and water inlet from back of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing partition for different type of urinals.19 to 20 mm thick Granite stone partition size 375mm x 750mm

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge) Size 600mmx450mm

Dismantling Sanitary fixtures such as Eurpoean/Indian/Orissa W.C., PVC / China ware cistern, Wash Hand Basin, Urinal Pot, Sinks and CP Fittings and disposal of dismantled material within a distance of 100 Mtr. complete in all respect as required by Engineer-in-Charge. Eurpoean/Indian/Orissa W.C.,

PVC / China Ware Cistern

Wash Hand Basin / Urinal Pot

CP Bib Cock/Angle Cock/Stop Cock/Shower/Bottle Trap

Bathroom Assessories such as Soap Dish, Towel Rail, Towel Ring, Towel Bracket, Mirror, Toilet Paper Holder, Seat Cover, Jet Pressure and all other accessories.

Providing and fixing in position C.P. Brass Auto close bib Cock of approved make (to the approval of Engineer-in-charge)

Providing and fixing in position C.P. Brass Auto close Pillar Cock of approved make (to the approval of Engineer-in-charge)

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect. PVC tube connection of size 15 mm x 450 mm with C.P. Brass nut

Providing and fixing in position automatic brass Ball Cock in tanks. Brass Ball Cock with rod and Plastic Ball 25mm i/d

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. Triple Layer Tanks 2 no x 500 = 1000 Ltr. Triple Layer Tanks 6 no x 1000 = 6000 Ltr. Total = 7000 Ltr.

Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect.

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x 300 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Extra for 1st Floor area

Dismantling of floor tiles at any floor of the building, laid in cement mortar including dismantling of cement concrete base and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect.

Providing and laying Rectified Porcelin floor tiles 400x400mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20mm thick bed of Cement Mortar 1:4 ( 1 Cement : 4 Fine sand) for new flooring or laid with cement based high polymer modified quick set tile adhesive (water based) of approved make IS 15477 marked using 5 Kg adhesive per Sqm of tile area in average 3mm thickness over existing floor, including pointing the joints with white cement and matching pigments etc., complete

Extra for 1st Floor area

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition Size 75 mm x 75 mm

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required. Through wall 11.43 cm thick

Providing & Fixing in position C.P. Brass flange of Dome approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-incharge )with various fixtures complete in all respect. C.P. Brass extension piece, 25mm long to 50mm long

Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect.

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects.

Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect. C.P. Brass khunti with 4 pegs

Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification of reputed firm of the self cleaning design with S.S. grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc. With 100mm x 75mm i/d Floor Trap (weighing 4.0 Kg)

CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-inCharge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge.SDR 11 CPVC pipes & fittings 20mm o/d

SDR 11 CPVC pipes & fittings 25mm o/d

SDR 11 CPVC pipes & fittings 32mm o/d

CPVC SDR 11 Pipe & fitting 40mm o/d

Making connection with the existing G.I. branch main up to 40mm size pipe including cutting of existing pipe line, threading of pipe lines from both ends and fixing of G.I Tee etc. in the pipe line (including cost of G.I Tee) complete in all respects.

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. For 110mm o/d pipes Single Tee With Door

Vent Cowls

Coupler

Elbow 90 Degree (All side socketed)

Single Tee

Cross Tee/Double Tee

For 90mm o/d pipes Single Tee With Door

Vent Cowls

Coupler

Exaust fan

Providing & Fixing Aluminium Door

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 90mm o/d SWR UPVC pipe lines laid complete

110mm o/d SWR UPVC pipe lines laid complete

Jointing of Sewer line to Municipal Committee Sewer System Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects. 200mm o/d SWR UPVC pipe lines laid complete

160mm o/d SWR UPVC pipe lines laid complete

Road Dismantling and Recondition (PWD B&R B.T. Bill)

Telecommunication line repair

Water Supply line repair to Municipal Committee

Constructing brick masonry manhole in cement mortar 1:5 ( 1 cement : 5 coarse sand ) with RCC core wall between masonary, R.C.C. top slab 20mm thick using M-20 mix, foundation concrete 1:4:8 mix (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making benching in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, Orange coloured PVC steps including RCC cover with frame internal dimensions.complete as per standard design. (In water logged ar Inside size 120x180 cm and 120 cm deep

Providing and fixing RCC manhole covers only 560mm i/d RCC man hole cover only as per ISI Heavy duty

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. 100mm internal Diametre H.C.I. gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design 450mm x 600mm inside with 455mm x 610mm cover and frame light duty double seal

Repair of Inspection Chamber cover with frame

Repair of Manhole

Disilting all types of main sewers 760 mm and onwards internal dia by silt clearing machines addopting all safety measures and disposal of silt upto 5km complete in all respects.

Rain water Harvesting

Electrical Works

RECESSED AIR CONDITIONER SUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):-Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height.

RECESSED COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Wiring Computer supply terminal points recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp. Switches and blanking plate etc., and covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring Computer terminal point having 3 Nos. 6Amp. 2/3 universal socket (shuttered), 1No. 16 Amp. switch with indicator and 1No. blanking plate (Modular accessories).

RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Supply and erection of TV socket, Telephone socket and Networking socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module), covered with Frame Plate and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring Networking socket point RJ45 (one module)

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring fan point (With fan box)

Wiring light point

Wiring 6Amp. wall socket point

Wiring 6Amp. Plug control comprising wall socket point

Wiring 16/20Amp. power plug control point

SURFACE PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia (ISI Marked) installed on surface etc., complete with PVC boxes (Plastic on surface boxes) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), MS saddle clamp, PVC Circular junction Boxes (Four way 1½" deep for walls), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material and painting as required:- Wiring fan point (Without fan box)

Wiring light point

Wiring 6Amp. wall socket point

Wiring 6Amp. Plug control comprising wall socket point

Wiring 16/20Amp. power plug control point

REPLACEMENT OF WIRES, COVER FRAMES, MODULAR SWITCHES, CONCEALED METAL BOXES AND OTHER ACCESSORIES IN THE EXISTING RECESSED CONDUIT PIPE WIRING SYSTEM (WITH MODULAR TYPE ACCESSORIES) Derived from 34.01: Replacement of PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in existing heavy gauge welded conduit pipe 20 mm/25 mm dia (1.6mm thick) ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), PVC Bush, bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- (Derived From CSR 34.01) Wiring fan point (Without fan box)

Wiring light point

Wiring 6Amp. wall socket point

Wiring 6Amp. Plug control comprising wall socket point

Wiring 16/20Amp. power plug control point

PVC INSULATED FR COPPER CONDUCTOR CABLES: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Overall size 1.5sq.mm (Un-sheathed)

Overall size 2.5sq.mm (Un-sheathed)

Overall size 4sq.mm (Un-sheathed)

Overall size 6sq.mm (Un-sheathed)

Overall size 10sq.mm (Un-sheathed)

COPPER CONDICTOR CABLES FOR SPECIAL ELECTRICAL SERVICS: Supply and erection of CAT 6 with 23AWG solid bare copper conductor, special grade PE insulation with star separator, 4pair unshielded twisted pair (UTP) industrial cable, FR PVC sheathed, class-E, 250 MHz of bandwidth, supporting data transfer speeds of up to Gbps (10GBASE-T) for distance up to apporximately 180 feet, cables are manufactured and tested to meet the ANSI/TIA 568-C.2 and ISO/IEC 11801 class E standards left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Cat 6 Lan Cable

XLPE INSULATED LT CABLES:XLPE INSULATED UN-ARMOURED CABLES (LOOSE): Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- Overall size 10sq.mm (2Core) Un-armoured (Loose)

Overall size 35sq.mm (3½ Core) Un- armoured (Loose)

Overall size 50sq.mm (3½ Core) Un- armoured (Loose)

Overall size 70sq.mm (3½ Core) Un- armoured (Loose)

Overall size 185sq.mm (3½ Core) Un- armoured (Loose)

Overall size 16sq.mm (4Core) Un-armoured (Loose)

HEAVY GAUGE WELDED CONDUIT PIPES: Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:- Supply & erection of 19/20mm dia. M.S. conduit pipe (1.6mm thick), White painted suspension rod for ceiling fan.

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface)

Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed)

Heavy Gauge PVC Conduit Pipe 32mm dia. (Flushed)

Supply and erection of PVC flexible pipe complete without compression glands, locking arrangement, check-nuts as required:- PVC Flexible Pipe 25mm dia.

PVC Flexible Pipe 32mm dia.

GALVANIZED IRON PIPES AND G.I. EARTHING Supply & erection of G.I. pipe (A-Class) as per IS:1239 (Part-I) 2004 including sockets, bends, inspection boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:- Galvanized Iron Pipe 50mm dia. (A-class) On surface

Earthing earth rod 20 mm dia for providing earth connections upto line earth with G.I. Wire 8 S.W.G. (4mm dia.). The rod shall be tapered at one end and flatted on other end. The hole size 10mm dia shall be drilled on the flatened side for facilitating connection with G.I. wire and thimble etc. The rod shall be erected in ground upto complete length vertically:- GI Earth rod 20 mm dia., 3 mtr. Long

G.I. EARTHING WIRE/ ROPE (AS ADDITIONAL LENGTH): Fixing additional length of earthing with G.I. wire/ rope in G.I. pipe (Flushed in wall and floor) with sockets, elbows and Steel hooks including the cost of cutting and filling up of chases (with finishing the surface):- Additional length G.I. wire 8 S.W.G. (4mm dia.) in 15mm dia. G.I. pipe (Flushed)

COPPER EARTHING: 8 SWG COPPER EARTHING : Earthing with 8 SWG (4mm dia.) electrolytic copper wire thimbled (1No. copper thimble with suitable size steel bolt, washers & double nut) with 30cm x 60cm x 2mm thick copper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:- Earthing with 8 SWG (4mm dia.) copper wire thimbled with 30cm x 60cm x 2mm thick copper plate burried 4.50 metre (14.76 feet) below ground level (up to 8metre in Length) with G.I. pipe 20mm dia. (A-class), 3metre long

COPPER EARTHING (Upto 8 metre in Length): Earthing Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 4.50 metre (14.76 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 8metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 3metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:- Earthing with 20mm x 3mm Copper Tape (upto 8Metre in Length)

COPPER EARTHING STRIP (As Additional Length): Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty material as required etc.:- Additional Length 20mm x 3mm thick Copper Tape

Fixing additional Length of earthing with 8 S.W.G. (4mm dia.) copper wire in G.I. pipe with sockets, elbows, steel hooks and GI saddle clamps including painting etc.:- Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (On Surface)

Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (Flushed)

SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- Modular Blanking Plate (One Module)

Ceiling Rose (Flush Piano type)

Call Bell 220/230 volts AC Ding Dong

BAKELITE SHEET: Supply and erection of brown bakelite sheet white glazed translucent backside painted 3mm thick (thickness not less than 3mm) on the existing metal box including cutting, fixing and connection of existing switches and sockets and other petty material etc.

Supply and erection of Plastic surface boxes of various sizes (1/2M, 3M, 4M, 6M, 8M, 12M) on surface on wall for mounting modular accessories including fixing and other petty material etc.:- Plastic Surface Box for Modular Accessories Twelve Module

MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: MINIATURE CIRCUIT BREAKERS: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- MCB Single Pole 6-32amp. (10kA, Curve-C)

MCB Four Pole 40amp. (10kA, Curve-C)

MCB Four Pole 50, 63amp. (10kA, Curve-C)

MCB Triple Pole 50, 63amp. (10kA, Curve- C)

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color- coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- SP&N Double Door Distribution Board 4 way each

SP&N Double Door Distribution Board 8 way each

TP&N Horizontal Double Door Distribution Board 4 way each

TP&N Horizontal Double Door Distribution Board 8 way each

Supply and erection of sheet metal double door vertical distribution boards IP 43-IK09 metal door (dust protected) as per IS:8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars for each phase, 2 Nos. shrouded neutral bars, 2Nos. earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting MCCB's as incomer and outgoings SP/TP miniature circuit breakers in the distribution board as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc.:- TP&N Double Door Vertical DB's 4 way each (With provision of FP MCCB upto 125amp)

Supply and erection of sheet metal Cable End Box (Make is same as MCB Distribution Board) mounting on the top or bottom of the MCB Distribution Board (Either Horizontal or Vertical) to keep loose wires & cables as per PWD General specifications including petty materials etc as required:- Cable End Box for SPN 4Way

Cable End Box for SPN 8 Way

Cable End Box for TPN 4 Way

Cable End Box for TPN 8 Way

SHEET METAL IRON CLAD CHANGEOVER SWITCHES: Supply and erection of sheet metal Iron Clad Changeover Switch on existing surface with G.I. bolts & nuts/rag bolts and nuts etc., according to the size of holes in the body of the switch including connections with suitable size of thimbles and bonding to the existing earth as per PWD General Specifications:IC Four Pole Changeover Switch 320amp., 415volts

SHEET METAL BUS BAR CHAMBERS (COPPER STRIPS): Supply and erection of sheet metal bus- bar chamber (factory fabricated) duly powder coated on existing surface with required 4Nos. of tin plated copper bus- bar strips of suitable length and cross- sectional area mounted on DMC/ SMC moulds at sufficient distance, enclosure made of M.S. sheet 1.6mm thick with hinged cover and lock, fitted with dust excluding gaskets and secured with sufficient no. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/ rag bolts and nuts etc. complete with all accessories including connections with suitable size of thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge at site: Bus Bar Chamber 100amp., 415volts Overall Dimensions (350mm x 450mm x 150mm) nominal

Bus Bar Chamber 200amp., 415volts Overall Dimensions (780mm x 510mm x 215mm) nominal

LT Panel enclosure having space for 1No. Incomer MCCB 630Amp. and 6Nos. outgoing MCCB's 40amp. to 250amp. (Option: MCCB 200-250amp.= 2Nos. and MCCB's 40-100amp.= 4Nos.) according to the requirement at site (Approx. size 1475 x 1800 x 400mm)

MCCB's (FOR PANELS & SHEET ENCLOSURE): Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubical type) in the existing Cubical Panel (confirm to IEC:60947-2) having Ics=100% Icu, 100% neutral with spreader terminal links, Extended rotary handle and relevant PWD general specifications complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with suitable size of thimbles etc:- MCCB Four Pole 63/80/100amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting

MCCB Four Pole 125amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting

MCCB Four Pole 250amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting

MCCB Four Pole 630amp., 415volts, ≥36kA Microprocessor Based Adjustable Thermal and Magnetic Setting

MCCB's (MOULDED CASE CIRCUIT BREAKER): Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubical type) in the existing Cubical Panel (confirm to IEC:60947-2) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD general specifications complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with suitable size of thimbles etc:- MCCB Four Pole 63/80/100amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting

MCCB Four Pole 250amp., 415volts, ≥36kA Microprocessor Based Adjustable Thermal and Magnetic Setting

MS SHEET ENCLOSURE FOR MCCB's: Supply & Erection of indoor type MCCB enclosure of suitable size having provision for MCCB with extended rotary handle. The Enclosure shall be made from 14/16 SWG CRCA sheet, confirming to IS 8623/1977-82. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The Enclosure door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. The Enclosure will be wall mounting type having provision for cable entry from bottom/top with cable glands etc. The sheet metal is sprayed with corrosion resistant etch primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work:- MS Sheet Enclosure having provision for MCCB 40-160Amp.with extended rotary handle (Approx. Size 500mm x 300mm x 200mm)

MS Sheet Enclosure having provision for MCCB 200-630Amp.with extended rotary handle (Approx. Size 750mm x 300mm x 250mm)

SINGLE ARM BRACKETS FOR GI PIPE POLE: Supply and erection of G.I. Pipe 40mm dia. (A-class) Single arm bracket of suitable length give a total overhang at a tentative angle of 100/105º, the bracket should be fixed on the top of the GI pipe pole having top outer dia. 80mm/100mm with GI reducer of suitable size with two coats of an approved aluminium paint complete in all respect as approved by the Engineer-in-charge at site:- Single Arm Bracket 1.5 metre Long with G.I. Reducer 80mm x 40mm

3-STEPPED STEEL TUBULAR POLE: Supply and erection of 3-Stepped steel tubular swaged and welded pole (410-SP Mpa) of suitable length confirming to IS: 2713- (PART-II)-1980 (Steel tubes confirming to IS: 1161-1979, UTS 42 kgf/ Sq.mm) to fix up to a required planting depth below ground level in a hole of excavation about 45 cm dia. and suitable depth to fill up to 15 cm below G/L with 1:2:4 cement concrete mixture including painting of pole with two coats of approved aluminium paint as required:- Overall length 7 metre, with planting depth 1.25 metre, length of sections 4 metre, 1.5 metre and 1.5 metre (Bottom, Middle and Top respectively), Outer dia and thickness of sections 114.3mm x 4.5mm, 88.9mm x 4.05mm and 76.1mm x 3.25mm (Bottom, Middle and Top respectively) with approximate weight 73 kg. (410 SP-2) and base Plate weight 7.5 kg. of size 12mm thick about 30 cm dia.

CEMENT CONCRETE MUFFS: Making of Cement Concrete muff of suitable size and length with 1:2:4 cement concrete mixture. The muff is to be made around the steel tubular pole sufficient to completely flush a SMC Junction Box (Glass Fibre reinforced polyester sheet moulding compound) confirming to IS:14772, inner dimensions 250mm x 200mm x 100mm with ± 10% tolerance in size & hinged water tight cover with locking arrangement having 1No. terminal strip with 4Nos. terminals & 1No. Single pole MCB of required capacity fixed on din bar (Din Bar Provision for 2Nos. MCB's). The SMC junction box is to be fixed with the pole by a MS flat clamp of size 20mm x 2mm thick. PVC pipe 40mm dia. (2No.x0.60m) should be provided for incoming and outgoing cables. The outer surface of the muff shall be finished with pure cement& two coats of white snowcem complete in all respect as approved and desired by the Engineer In-Charge at site:- Cement Concrete Muff of Overall Size 450mm dia., 80cm Long

Supply and erection of SMC Junction Box (Glass Fibre reinforced polyester sheet moulding compound) confirm to IS:14772 (Recessed/ On surface), robustly constructed, safe & shock proof, rust & tamper proof of suitable inner & outer dimensions with ± 10% tolerance in size & hinged water tight cover with locking arrangement having 1No. terminal strip with 4Nos. terminals & 1No. Single pole MCB of required capacity fixed on din bar (Din Bar Provision for 2Nos. MCB's) complete in all respect as approved and desired by the Engineer In-Charge at site:- SMC Junction Box (Glass Fibre reinforced polyester sheet moulding compound) confirm to IS:14772, inner dimensions 140mm x 140mm x 95mm with hinged water tight cover with locking arrangement

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:- Double Walled Corrugated HDPE Pipe 50/38mm (Outer/ Inner dia.)

Double Walled Corrugated HDPE Pipe 90/76mm (Outer/ Inner dia.)

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:- Aluminium thimble cable Core size 50sq.mm

Aluminium thimble cable Core size150sq.mm

Aluminium thimble cable Core size185sq.mm

Supply and erection of Heavy duty Exhust Fans 300mm sweep 900RPM complete with aluminium louver shutter Canon Make, double ball bearing, longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site.

Supply and erection of LED batten 20 Watt LED (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/ IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including their drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited labortary.

Supply and erection of LED batten 40 Watt LED (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimum 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/ IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including their drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited laboratory.

Supply and erection of Receesed Mounted 36Watt LED Panel (including constant LED driver) with CRCA sheet having efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including there drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site. LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No: AT/2021/GL/1410-1422, Dated: 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited laboratory.

Supply and erection of 3-Star rating AC Ceiling Fan 1200mm (48") suitable for single phase ACsupply with double ball bearing, copper wound,anti corrosive 3Nos. of blades and body, white in colour. Down rod mounting type. The product should posses a minimum air delivery of 210CMM. The product should have a manufacture's guarantee/warranty of minimum 2 years.The product should be complete in all aspects with fan motor, conopy set, shackle kit, etc., including erection & testing of ceiling fan having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75 sq. mm complete in all respects as per satisfcation of the Engineer in-charge at site.

Supply and erection of LED Street Light Luminaire 45 watt, Supply voltage 140-270 volts AC supply, 50Hz ± 35 (including BIS Certified potted single driver with screen or laser printing logo LED driver) with pressure die cast or extruded alumininum housing with control gear (IP 66 protection) THD<10%, CRI minimum 70, High power LED (with wattage 1 to 5 Watt) with mandatory secondary lenses, toughened glass fitting, Min IK07, 4 KV SPD within driver and 10KV external SPD, efficacy of LED fixture minimum 120 lumens per watt, 5 year warranty including their drivers complete in all respects as approved and desired by the Engineer in-charge at site . LED Fitting as per Specifications approved by Hon. Tech. Advisor to Punjab Govt. vide Letter ION no:- AT/2021/GL/1410-1422 Dated 06/05/2021. Besides this the lighting fixtures manufactures should have in house NABL accredited labortary.

Supply and erection of LED Flood Light 50watt, Supply Voltage 140-270Volts AC supply, 50Hz ± 3% (including BIS Certified potted single diver with screen or laser printing logo LED driver) with pressure die cast or extruded aluminium housing with control gear (IP 66 protection), THD<10%, CRI minimum 70, High power LED with wattage 1 to 5 Watt with mandatory secondary lenses, toughened glass fitting, 4 KV SPD within driver and 10KV external SPD, Min IK07, efficacy of LED fixture minimum 120 lumens per watt, 5 year warranty including their drivers complete in all respects as approved and desired by the Engineer in-charge at site. LED Fittings as per specifications approved by Hon'ble Technical Advisor to Punjab Govt. vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufacturers should have in house NABL accredited lab.

Note- Dismentle (Less 15000)

Please Enable Macros to View BoQ information