REPAIRS TO JOINERY, PLASTER, PLUMBING, SANITARY FITTINGS AND ALLIED WORKS AT KALIMPONG UNDER GE 867 EWS

Amount

M&L for rendering 15mm thick on brickwork or concrete surfaces of walls in cement mortar 1:6 finished even and smooth without using extra cement including taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water etc., including removing rubbish out side MD land complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick on concrete surfaces of ceilings/chajjas in cement mortar 1:3 finished fair and even including taking down cement or cement lime plaster, any description on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water etc., including removing rubbish out side MD land complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. Make for item Nos. 3&4: LOVELYCEM/ SURYACEM/ JANATHACEM/LUCKYCEM or equivalent make as approved by GE.

Taking down shutters of any description area exceeding 1 Sqm but not exceeding 2 Sqm each easing and refixing in same opening complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.after fixing new frame complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.5 Sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. after fixing new frame complete all as specified and as directed.

Taking down chowkats or frames area not exceeding 1.50 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.after fixing new frame complete all as specified and as directed.

Taking down chowkats or frames area exceeding 1.5 Sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC 1:2:4 type B1 or cement mortar 1:4 (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. after fixing new frame complete all as specified and as directed.

Taking down shutters of any description area exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

Taking down shutters of any description area not exceeding 1 Sqm each complete all as specified and as directed.

S&F second class hardwood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid ,rounded or chamfered put together with glue pinned joints all as specified and directed. TIMBER: - Sal/Kalasiris/Chaplash/Hollock/Bijasal

S&F 105x60 mm size pressed steel door frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including PCC 1:3:6 type C0 filling complete all as directed by Engr-in-Charge. Make: - DIWAN STEELS/AVA/AJANTA or equivalent as approved by GE.

S&F 125x60 mm size pressed steel door frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including PCC 1:3:6 type C0 filling complete all as directed by Engr-in-Charge. Make: - DIWAN STEELS/AVA/AJANTA or equivalent as approved by GE.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of 12mm thick timber flat on both sides or of 12mm thick veneered particle board ,medium density, wood particle board with commercial face veneers with sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified directed by Engr-in-charge.

S & F 35 mm thick second class hard wood Glazed and skeleton shutters for doors, open rebated and prepared to receive glass, gauze etc., with out sash bars, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats all as specified and directed.

S & F 30 mm thick second class hard wood Glazed and skeleton shutters, for windows and ventilators, open rebated and prepared to receive glass,gauze etc. divided in to squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b) fitted to chowkats all as specified and directed. Timber for item Nos. 15 to 17:- Sal/Kalasiris/Chaplash/Hollock/Bijasal

S&F factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification and dawings.

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing. Make for Item No. 18&19: - SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

S&F steel window with side hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays, with glazing bars for receiving glass / MS flat for receiving wire mesh including taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

S&F steel window with side hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays, without glazing bars taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

S&F steel ventilators with top hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

S&F steel windows or ventilators with fixed type with glazing bars taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge. Make for Item No. 20 to 23: M/s Madhu industries / M/s.SEN Harvick / AVA STEELS /M/s. Shiv Mular / M/s. AGEW. / M/s. Multiwyn Industries Corpn/ M/s Ganesh rolling shutters/M/s Venkateswara rolling shutters or equvalent make as approved by GE.

S&F 40mm thick factory made flush shutters, solid core construction with block board core and plywood face panels, both faces are covered with decorative face vener with lipping/ frame to match complete all as specified and directed by Engineer-in-Charge. Make: - Green Ply/Archid Ply or equivalent as approved by GE.

M&L Mild steel work such as bands, straps, clamps and hold fasts etc. of Fe-290 Gde E-165 all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beeds all as specified and directed.

S & F in repairs Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beeds all as specified and directed.

S & F 3mm thick sheet glass ordinary quality fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

Hacking out old broken glass and S & F 3mm thick sheet glass ordinary quality fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

S & F 4mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

Hacking out old broken glass and S & F 4mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts area exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge. Make for item Nos. 28 to 31:- TRIVENI/ SAINT GOBAIN/ MODIGUARD/ATUL/ HINDUSTAN or equivalent as approved by GE.

S&F Mild steel works as in grills, framed guard bars, and similar works conforming to F2 290, Gde E-165 all as specified and directed.

S&F in repairs 100 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F 100 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F 75 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F 100 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 125 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed. Make for Item No. 33 to 42: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE

M&L for 4mm thick asbestos cement building boards, fixed with screws to tmber frame work including taking down existing boards of any type and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge. Make:- SWASTIK/CHARMINAR/ UPAL/ VISAKHA or equivalent as approved by GE.

M&L for second class hard wood clean sawn fillets of sectional area exceeding 13 Sqcm and not exceeding 25 Sqcm, square, rectangular or triangular in section, fixed with nails or brads including taking down existing fillets complete all as specified and as directed by Engineer-in-Charge. WOOD: Sal/Kalasiris/Chaplash/Hollock/Bijasal

M&L for second class hard wood wrought fillets of sectional area exceeding 3 Sqcm and not exceeding 6 Sqcm, square, rectangular or triangular in section, fixed with nails or brads complete all as specified and as directed by Engineer-in-Charge. WOOD: Sal/Kalasiris/Chaplash/Hollock/Bijasal

M&L for 12mm thick plywood with commercial face veneers, BWR grade, type BB, fixed with screws to tmber frame work iincluding taking down existing plywood of any type complete all as specified and directed by Engineer-in-Charge.

M&L for 18mm thick prelaminated particle board, interior grade, prelaminated on one side with choice lamination and other side balancing white lamination with 6mm thick teak wood lipping allround fixed with screws to timber frame work complete including taking down existing unserviceable boarding of any description all as directed by Engr-in-charge. Make for ItemNo. 46&47:- Green ply/Kitply/Century/National/Swastik/ Ecoboard/Alishan/ Marino/ Archid/Novapan or equivalent as approved by GE.

M&L for first class hard wood wrought fillets of 6mm thick as in lipping to exposed edges of particle board, fixed with nails or brads complete all as specified and as directed by Engineer-in-Charge. WOOD: 1st class teak wood

M&L for second class hard wood wrought fillets of sectional area not exceeding 3 Sqcm, square, rectangular or triangular in section, fixed with nails or brads complete all as specified and as directed by Engineer-in-Charge. WOOD: Sal/Kalasiris/Chaplash/Hollock/Bijasal

M&L preparing new wooden surfaces of any description not exceeding 10 cm width or girth when unconnected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L Preparing new or previously un treated surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

M&L preparing new or previously untreated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. Make for Item No. 50 to 52:- ASIAN/ SHALIMAR/ BERGER/JENSON& NICHOLSON/IEL

M&L Preparing surfaces of wood and wood based materials, steel and iron work , new or old, of any description not otherwise described exceeding 0.10 Sqm and not exceeding 0.50 Sqm each, and treated with tar or coal tar black paint complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in leveling coarse for tile flooring and finished even and rough uto receive toping layer including demolition of existing concrete and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm thick plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in floors laid in alternative bays and finished even and smooth using extra cement including demolition of existing flooring and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L for 3mm thick 38mm wide inserted in position in flooring to confirm to design complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 or with chemical tile adhisive (SIKA) including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 or with chemical tile adhisive (SIKA) including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 or with chemical tile adhisive (SIKA) including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for coloured glazed ceramic tiles of size 300x200x7mm thick on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 backing coat including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for 10mm thick vetrified ceramic tiles of light shade (square/rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar 1:6 including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for 10mm thick vetrified ceramic tiles of light shade (square/rectangular) polished area of each tile not exceeding 0.36 sqm, in skirting etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar 1:4 including dismantling existing tiles and removing rubbish off the premises complete all as specified and directed by Engr-in-charge. Make for Item No 57 to 62: NITCO/ SOMANY/ ASIAN / JOHNSON/ORIENT

M&L for 17 to 20mm thick Granite slab of any type and colour machine cut in steps, jambs, pillars, window cills, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and rounding exposed edges complete laid over and including 20 mm thick rendering in cement mortar 1:6 including dismantling existing stone slabs and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for reinforced cement concrete 1:2:4 mix, type B1 (using 20 mm graded stone aggregate) as in chajjas and the like including demolition of existing chajja and removing rubbish off the premises all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

Use and removal of steel formwork to soffits of chajjas and similar item including edges, for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

M&L for Mild steel deformed TMT bars 10mm dia and above as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

M&L for Mild steel deformed TMT bars 8mm dia as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

S&F 15mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete including short lengths including taking down existing GI pipe all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

Cutting chases, plainning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, sillls, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good cutting not exc 10 cm girth in brick walls built in cement mortar complete all as directed by Engr-in-Charge.

Taking down existing IWC along with its cement concrete bedding and P or S trap and S&F Orrissa pattern vitreous china squatting pan white colour of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including cement concrete bedding and P or S trap as required including PVC pipe upto finished floor level to connect flush pipe, making good all the disturbed surfaces of floor to match the adjoining complete all as directed by Engineer-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F Vitreous china wash down water closet pan (pedestal pattern) white, excluding flushing cistern and flush pipe but including Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, including taking down existing unserviceable/broken EWC complete all as specified and directed Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

S&F PVC valveless, symphonic action type, flushing cistern 10ltr capacity, low level, white with inlet ball valve float and handle along with suitable flush pipe/bend including brackets fixed in repairs complete all as directed by Engr-in-Charge. Make: PARRY WARE (SLIMLINE)/ COMMANDER/ HINDWARE

S&F Vitreous China wash basin, white, flat back, of size 550 x 400 mm, excluding taps, waste chain and plug and porcelain stopper but including brackets and 32mm dia PTMTwaste fitting, including taking down existing unserviceable/broken wash hand basin all as specified and directed by Engr-in-Charge. Make: HINDWARE / NEYCER/ PARRYWARE / CERA

M&L for 32mm dia bore low density poly ethylene pipe (LDPE) of pressure rating 6 Kg/Sqcm fixed complete to wall, ceiling etc., complete all as specified and directed by Engineer-in-Charge.

M&L for 40mm dia bore high density poly ethylene pipe (HDPE) of pressure rating 6 Kg/Sqcm fixed complete to wall, ceiling etc., complete all as specified and directed by Engineer-in-Charge.

S&F in repairs of 1mm thick stainless steel sink with drainage board kitchen or laboratory type with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed. Make: DIAMOND/ COBRA/PRINCE / NIRALI / NATIONAL/ JAYNA/ PHENOX or equivalent as approved by GE.

Taking down existing mixing valve (Mixture unit) and refixing including three joints to pipes or unions and plugging and screwing complete all as specified and directed.

S&F in repair Brass chromium plated shower rose with or without swivel joints 125 mm size , including fixing to steel pipe or unioncomplete all as specified and directed. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F in repairs PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F in repairs Stop/angle valves 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, concealed type with long shank ang cup screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F in repairs bib taps 15 mm bore, cast copper alloy chromium plated screwed down high pressure, fancy type with crown or capstan head, screwed for iron pipe all as specified and directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE)

S&F in repairs 100 mm dia PTMT grating dome (Minimum weight 25 Gms)complete all as directed by Engr-in-Charge. Make:- PRAYAG/POLYTUFF or equivalent as approved by GE.

S&F in repairs kitchen plate rack made out of stainless steel 1.00 mm thick sheet with partitions and size of rack 800 x 250 x 900 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed. Make: DIAMOND/ COBRA/PRINCE / NIRALI / NATIONAL/ JAYNA/ PHENOX or equivalent as approved by GE.

S&F in repair towel rail 600mm long between flanges 20mm dia brass chromium plated D type complete all as directed by Engr-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE or equivalent as approved by GE.

S&F in repairs soap dish, brass chromium plated fixed with plugs and chromium plated brass screws all as specified and directed by Engineer-in-Charge. Make: SEIKO/RYBO/SPECTRUM/ NMC/L&K/ESSCO (DELUXE or equivalent as approved by GE.

S&F CP wall mixer fancy type 3 in one system with provision for both telephone shower and overhead shower complete with bend pipe 15mm including taking down existing old unserviceable mixer complete all as specified and directed by Engineer-in-Charge. MAKE: HINDWARE Cat No. F110019 or equivalent in JAQUAR/ESSCO (DELUX)

S&F CP toilet paper holdr including taking down existing old unserviceable toilet paper holder complete all as specified and directed by Engineer-in-Charge. MAKE: HINDWARE Cat No. F840009 or equivalent in JAQUAR/ESSCO (DELUX)

S&F CP Sink mixer including taking down existing old unserviceable sink mixer complete all as specified and directed by Engineer-in-Charge. MAKE: HINDWARE Cat No. F720020 or equivalent in JAQUAR/ESSCO (DELUX)

S&F in repairs CP connection 450mm long 15mm dia braided hoses with nuts and rubber washers without nippels(suitable for geysers, basin mixer) complete all as directed by Engineer-in-Charge. MAKE: HINDWARE/JAQUAR/ESSCO (DELUX)

S&F in repairs brass chromium plated Health faucet with 8 mm dia, 1.00mtr long flexible pipe for EWC including wall hook complete all as specified and directed Make:-Jaquar/Hindware./Parryware/Neycer/Cera

S&F in repairs central hole basin mixer without popup waste brass chromium plated CP complete all as specified and directed Make:-HINDWARE Cat No. F720014 or equivalent in JAQUAR/ESSCO (DELUX)

S&F in repairs CP angular stop cock with wall flange complete all as specified and directed Make:-Jaquar Cat No. Vol-17 (OPP-15053) or equivalent in ESSCO (DELUX)HINDWARE/Parryware/Neycer/Cera

S&F PVC (SWR) pipes 75mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors including taking down existing pipes complete all as directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110mm bore single socket in any length with rubber ring joints fixed to wall or laid in floors including taking down existing pipes complete all as directed by Engr-in-Charge.

S&F in repairs PVC (SWR) plain bends (any radius) suitable for 110mm bore pipe complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) bends (any radius) suitable for 110mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) plain bends (any radius) suitable for 75mm bore pipe complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) bends (any radius) suitable for 75mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) junction (single T) suitable for 75mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) junction (single T) suitable for 110mm bore pipe fitted with access door complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) reducer 110x75 mm complete all as directed by Engr-in-charge.

S&F in repairs PVC (SWR) vent cowl 75mm complete all as directed by Engr-in-charge.

M&L in repairs PVC (SWR) floor trap 75/110mm dia plain with grating including jointing with solvent cement and making good disturbed portions of floor matching with adjoining surfaces complete all as specified and directed by Engr-in-Charge. Make for item No 95 to 105: PRINCE/ SUDHAKAR/ NANDI/ FINOLEX/ SWASTIK/SUPRIME

S&F 100mm Size hasp & staple, safety type, aluminium alloy anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. Make: - CROWN/ CLASSIC/ JYOTHI/ AMIT/ MOWJEE

Sub Total of Schedule 'A'

Schedule of Credit (Minus) Rs. 33,475.00 B/F from Ser page No. 32 NOTE: Bidder shall insert credit amount as rate Rs. 33,475.00 in Green field under Col-M. If bidder does not insert the amount the same will be deducted from total amount of Schedule 'A' and accordingly total amount of tender will be considered in deciding the lowest tender.

Sub Total of Schedule of Credit

SANJAY SAW MILL

G K SUTHAR

DEEP CHANDRA JOSHI

HEM RAJ GURUNG

RAJU TAMANG

Sri Gupta Construction

GARGO TRADERS