SPECIAL REPAIR/REPLASTERING TO LIVING IN BILLET, ADDITION/ALTERATION OF GUARD ROOM, PROVISION OF SUN SHADE TO DSC POST WATCH TOWERS AND PROVISION OF HIGH MAST LIGHTS AT JANDWAL UNDER GE AIR FORCE STATION PATHANKOT

Amount

Demolition of cement concrete (unreinforced) as in padding layers of Roofs, floors (other than ground floors) and similar suspended work complete all as specified and as directed by Engr-in-Charge.

Cement concrete type B-0 1:2:4 (12.5mm graded aggregate) as in padding on existing roof surfaces & roof kerbs, rounded or chamfered on edges complete all as specified and as directed by Engr-in-Charge.

Rendering 10mm thick with CM (1:4) on concrete surface including WPC, roof finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge. (WPC measured and paid seperately)

Supply only integral liquid water proofing compound complete all as specified and as directed by Engr-in-Charge.

Material and Labour for water proofing treatment provided with polymeric water proofing membrane 3 mm, 90 micron weighing not less than 3Kg/Sqm on prepared sufaces vertical/horizontal laid over a coat of bitumen 85/25 @ 1.2 Kg/Sqm, over a coat of bitumen primer 0.50Kg/Sqm One coat of bitumen 85/25 @ 1.20 Kg/Sqm shall be provided over water proofing membrane as per manufacturers instructions complete all as specified and as directed by Engr-in-Charge. (Note : The overlaps shall be of minimum 75mm on longitudinal direction and 100mm on transverse direction)

Taking down cement plaster, any description on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed by Engr-in-Charge.

Rendering 15mm thick on the other than fair face of brick or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface including Water proofing compound and finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge. (WPC measured and paid seperately)

Rendering 5 mm thick cement plaster on ceiling surface in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

Preparation of newly platered or unplastered surfaces of wall and applying Two coats of exterior emulsion paint (weather coat) over a coat of primer in any shade or colour as approved complete all as specified and as directed by Engr-in-Charge.

Preparation of newly plastered wall or concrete surfaces and applying two coats of oil bound distemeper over a coat of primer over wall putty complete all as specified and as directed by Engr-in-Charge.

Preparation of surfaces and applying three coats of white wash on newley plastered surfaces of ceiling complete all as specified and as directed by Engr-in-Charge.

Preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed by Engr-in-Charge.

Complete removal of existing treatment by scrapping down completely on brick wall/concrete surafces thoroughly, washing, rubbing down with water cleaning the surafce upto the entire satisfaction of Engineer-in-Charge and applying two coats of Oil bound distemper over a coat of primer over wall care putty finishes complete all as specified and as directed by Engr-in-Charge.

Taking down chowkhat with shutters without taking off shutters from the frame exc1.5 Sqm but n.exc 4 Sqm each complete all as specified and as directed by Engr-in-Charge.

Taking down chowkhat with shutters without taking off shutters from the frame n.exc 1.5 Sqm each complete all as specified and as directed by Engr-in-Charge.

Supply and fixing 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-Charge.

Supply and fix 35 mm thick, glazed/skeleton shutters with second class hard wood,open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame made out of mild steel tubes for top and bottom rails . Mild steel frame shall be covered with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20 mm complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Aluminium anodised Ventilators of size upto 1.00 Sqm with Top hung glass shutter including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and fixing in brick/RCC wall with suitable fasteners/screws comprising of following specifications:- (a) Frame of Aluminium Section 47.62x44.45x1.88mm (b) Shutter Frame of Aluminium Section 47.62x44.45x1.88mm (c) Aluminium anodised Peg stay/stopper of suitable size -01 No for each shutter (d) Aluminium anodised tower bolt 100mm long - 02 No for each shutter (e) Aluminium anodised Handle 150mm Long - 01 No for each shutter (f) Aluminium anodised hinges 100mm long - 02 Nos for each shutter (g) 4mm thick tinted glass

Framed work as in chowkhats for doors or gates of angle or other scetion etc. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings also fastening and fixing complete conforming to Fe-410-W(Gde-E-250) quality-B, complete all as specified and as directed by Engr-in-Charge.

Cement concrete 1:3:6 Type C1 (using 20mm graded stone aggregate) for fixing hold fasts complete all as specified and as directed by Engr-in-Charge.

Supply and fixing butt hinges med weight cold rolled MS, size 100 mm complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Aluminium anodised, barrel tower bolts of extruded section 200mm long complete all as specified and as directed by Engr-in-Charge.

Supply and fixing 300mm long Aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Aluminium alloy handles, fabricated type, anodised 150mm size complete all as specified and as directed by Engr-in-Charge.

Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm as in doors complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Mild Steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engr-in-Charge.

Preparation of new wood and wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed by Engr-in-Charge.

Preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge.

Preparing old wooden surfaces & applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

Preparing old steel surfaces & applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed by Engr-in-Charge.

Brick work with sub class B bricks straight or curved on plan n exc 6m radius in CM 1:6 complete all as specified and as directed by Engr-in-Charge.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified and as directed by Engr-in-Charge.

Supply and fixing TMT steel bars 6 mm to 8mm dia cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and as directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubish of the premises complete all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed by Engr-in-Charge.

Material and labour 40 mm thick plain cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in floors finished even and fair, complete all as specified and as directed by Engr-in-Charge.

Rendering 15 mm thick in cement mortar 1:3 for fixing wall tiles on vertical surfaces complete all as specified and as directed by Engr-in-Charge.

Glazed coloured ceramic tiles in vertical surfaces 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar complete all as specified and as directed by Engr-in-Charge.

Glazed coloured ceramic tiles in vertical surfaces 200x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortar complete all as specified and as directed by Engr-in-Charge.

Non skid coloured ceramic tiles of size up to 10mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over screed bed complete all as specified and as directed by Engr-in-Charge.

Non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over screed bed complete all as specified and as directed by Engr-in-Charge.

Material and labour for Screed bed or bedding layer 10 mm thick in cement mortar 1:4 on floors for laying floor finish complete all as specified and as directed by Engr-in-Charge.

Material and labour for Machine Cut Kota stone slab flooring 18-20mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engr-in-Charge.

Material and labour for 20mm thick screed bed or bedding layer in CM 1:3 for laying floor finishes complete all as specified and as directed by Engr-in-Charge.

Cement concrete 50mm thick, 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth withiut using extracement and providing joints througout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed by Engr-in-Charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engr-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs etc acomplete all as specified and as directed by Engr-in-Charge.

Supply and fixing TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and as directed by Engr-in-Charge.

Material and labour for 18mm thick granite(of any type) work(table rubbed and polished) in steps, jambs,pillars, window-cills,cooking platforms and like in cement mortar 1:4, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the shade of granite complete all as specified and as directed by Engr-in-Charge.

Hacking out old glasses from steel window / ventilator in any position and any description including punching or drilling out old glazing pins / springs clips and providing and fixing new once and 3 mm sheet glass ordinary quality complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm as in doors and windows with necessary nuts and bolts/ fillets complete all as specified and as directed by Engr-in-Charge.

Supply and fixing drapery curtain rod of metalic 20mm dia covered with PVC coating complete with MS bracket golden colour rings and side caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and as directed by Engr-in-Charge.

Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified and as directed by Engr-in-Charge.

Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified and as directed by Engr-in-Charge.

Supply and fix steel tubes, galvanised 15 mm bore, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and as directed by Engr-in-Charge.

Supply and fix steel tubes, galvanised 20 mm bore, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and as directed by Engr-in-Charge.

Cutting chases,pinning in,making good to facings where required and pointing in cement mortar (1:3) for concealed water tubing or concealed cutting not exc 10cm girth in brick walls complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair Water closet vitreous china squating pan 'Orissa pattern 'size 580x440mm white with integral foot rest fixed in repair (excluding flushing cistern and flush pipe) complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair Urinal, Half stall type, white (Excluding flusing cistern, flush pipe and waste pipe) complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repairs PVC low level flushing cistern of 10 ltrs capacity incl all fitting complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair Counter type Wash hand basin (Oval shape) of size 560x410x180mm including cutting and making necssary arrangements for fixing in granite complete all as specified and as directed by Engr-in-Charge.

Supply and fixing PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair Bib cock with flange cast copper alloy CP 15mm bore dia. screwed for iron pipe or for brass ferrule and complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair cast copper alloy chromium plated Pillar cock 15mm dia screwed down high pressure with or without lettered (Hot or Cold) with long screwed shank and fly nuts screwed for iron pipe complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair angle cock with flange 15mm bore, chromium plated cast copper alloy with crutch or butter fly handle high pressure screwed down complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair 15mm bore Concealed type Stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair chromium plated shower roses with or without swivel joints, 125mm size including fixing to steel pipe or union complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair Chromium plated Soap dish,fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engr-in-Charge.

Supply and fixing for 50mm bore low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/cm2 laid in trenches, fixed to walls etc including necessary fittings such as bend/tee etc complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 50mm, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing steel tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe-410-W(Gde-E-250) quality-B complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Mild steel screw bolts (machine made) of dia of neck 11 to 15 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n exc 5cm long complete all as specified and as directed by Engr-in-Charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-Charge.

Cutting holes in brick walls Exc half brick but not exc one brick, built in cement mortar for inserting holdfasts and making good dismantled portion in cement concrete 1:2:4 Type B-1 complete all as specified and as directed by Engr-in-Charge.

Dismantling of asbestos cement corrugated or semi corrugated sheet in roof covering complete all as specified and as directed by Engr-in-Charge.

Dismantling of wrought iron or mild steel work of any description not otherwise specifically provided complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in any type of soil complete all as specified and as directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by Engr-in-Charge.

Spreading and levelling of soil obtained from excavation in floors in layers n exc 25cm thick and well ramming including watering complete all as specified and as directed by Engr-in-Charge.

Removing excavated material n.exc. 50m and depositing where directed to a level n.exc. 1.50m above starting point complete all as specified and as directed by Engr-in-Charge.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed/broken stone aggregate as in foundation, filling and mass complete all as specified and as directed by Engr-in-Charge.

TMT steel bars 5 mm dia and over upto and including 10 mm dia in stirrups , spacers and binders cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and as directed by Engr-in-Charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded aggregate) as Foundation beams, plinth beams, bases for columns etc complete all as specified and as directed by Engr-in-Charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded aggregate) as in beams, lintel band, roof band, gable band etc complete all as specified and as directed by Engr-in-Charge.

Formwork to flat rough finished surfaces of concrete of foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter complete all as specified and as directed by Engr-in-Charge.

Plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base, 100mm thick, complete all as specified and as directed by Engr-in-Charge.

Plain cement concrete 1:2:4 type B-1, 50 mm thick ( using 20 mm graded stone aggregate) as in floors finished even and fair, complete all as specified and as directed by Engr-in-Charge.

Rendering 15mm thick on fair faces of brick or concrete surface in cement mortar 1:6 finished even and smooth without using extra cementcomplete all as specified and as directed by Engr-in-Charge.

Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface and finished even and smooth without using extara cement complete all as specified and as directed by Engr-in-Charge.

Hard core of broken stone or boulder of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-Charge.

Supply and fix anodised aluminium frame for window with one or more rebates, anodised aluminium window, sliding typewith glazed and gauged shutters, sliding on three way aluminium channel, without sash bars, sliding on separate track, made out of aluminium section weighing 0.55 Kg/RM and necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, fittings such as suitable anodised aluminium locking type handle etc and fixing of 4.00 mm thick tinted glass, complete all as specified and as directed by Engr-in-Charge.

Supply and fix Anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening,complete all as specified and as directed by Engr-in-Charge.

Supply and fix pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed by Engr-in-Charge.

Supply and fix door closer of aluminium (extruded section) hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed by Engr-in-Charge.

Supply and fix Mild steel screw bolts purpose made with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 30cm long and diameter of neck exc 12 and n exc 20mm complete all as specified and as directed by Engr-in-Charge.

Position suspended false ceiling system using T-grid suspended ceiling grid system. The size of grid shall be 600x600mm with GI frame work main runner 38x24mmx3600mm, cross tee 25x24x600mm/25x24x1200mm and wall angle 24x24x2540mm (thickness of the material of 0.30mm) using 9mm thick ceiling panel laminated with PVC film on front face and foil back available in due drop texture as per IS-2095, part-I-1996, fixed in the grid of T-grid suspended ceiling grid system duly suspended by 4mm dia GI bar hanged from the purlins of the roof with butter fly clips all as specified and directed by Engr-in-Charge.

Supply, installation,testing and comissioning 12.5 mtr high mast suitable for 180 KM/hr wind speed and suitable for mounting max 06 Nos of x250 Watt LED luminaires consisting of the head frame, moveable lantern carriage, double drum winch, SS hoisting ropes of 7/19 const, Traling cable- 5 Core 6 Sqmm and incl LT Panel incl 2 Nos of availation light, 01 No. timer switch complete all accessories of required size all as directed by Engr-in-Charge and the following: (Note : High mast should be installed under guidence of Company engineer) : (a) foundation (as per drawing attached) incl bolts,nuts, anchor plate & template, lightning finial, twin red aviation light (LED type) incl separate connections and power tool (integral) complete all as specified and directed by Engr In Charge. (b) Mounting arrengement for 6x250 watt LED flood light fittings ( Note: one year maintinace of moterised and all system provided by Contractor from the date of completion) complete all as specified and directed by Engr In Charge.

Supply and fixing LED flood light 250 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engr In Charge.

Earthing complete with copper earth plate elect rode 600x600x3mm thick buried directly in ground to a depth not less than 4.5 mtr deep below normal ground level with top edge of the earth plate not less than 3.75 mtr deep below normal ground level connected to copper strip 20x3mm size as earthing lead by means of bolts, nuts, check nuts and washers of brass, GI protection pipe light grade 40mm bore up to test point 20mm dia GI watering pipe with funnel and wire mesh, PCC pit 1:2:4 type BI, RCC cover with suitable handle, earth pit filled with ground enhancing material i.e. mixture of copper sulphate, magnesia sulphate, graphite power etc mixed in equal quantity all around earth plate up to 15 cm and filled with vegetable soil above GEM up to ground level earth work in any type of soil all as required and directed including testing on completion complete all as specified and directed by Engr In Charge. Note : (i) Main earthing lead from earth plate electrode to test point upto length7.5 meterslength shall deem to be included in the unit rate quoted against this team. (ii) GI Protection pipe & eathing lead beyond 7.5 meters shall be measured and paid for separately. (iii) On testing after completion if the desired resistenance is not obtained the contractor shall redone the earthing without any extra cost.

Supply and fix copper strip 20x3.15 mm complete with saddles/ insulators made out of porcelain or fibre and fixing screws for roof conductor/down conductor including welding or brazing for joints all as required at site or directed by Engr In Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 4 core Complete all as specified and directed by Engr In Charge.

Material and labour for sand cushioning to underground cable 8cm thick before laying the cable and 15 cm thick after laying, stretching and testing the cable complete all as specified and directed by Engr In Charge.

Material and labour for sub class “B” bricks laid dry flat cover the cable with width equal to the length of cable, abutting each other for protection of cable complete all as specified and directed by Engr In Charge.

Taking down carefully copper/aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator light fittings etc and removing from site and making good disturbed surfaces of walls floors etc complete all as specified and directed by Engr In Charge.

Point wiring with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core calbel (green color) as earth lead in and including concealed non metalic rigid PVC conduit light grade with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size & 3mm thick plastic laminated sheet, incluidng cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and as directed by Engineer-in-Charge. (a) One light point/fan/exhaust/bell buzzer point controlled by one, one way switch

(b) One three pin 5 Amp socket on independent board

All as per item No.113 above but with 2.5 sqmm (nominal area) wire/cable for phase & neutral for one 3 pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable FRLS, 1100 volts grade as earth continuity conductor upto common earth & connected to earth & connected to earth dolly complete all as specified and directed by Engr In Charge.

All as per item No.113 above here in before but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and directed by Engr In Charge.

All as per item No.113 above here in before but for one 5A socket outlet on the same board controlled by one switch complete all as specified and directed by Engr In Charge.

Supply and fixing switch piano flush type single pile one way 230 volts 5/6 Amp complete all as specified and directed by Engr In Charge.

Supply and fixing socket outlet 3 pin, 230 volts 5/6 Amps flush type multipurpose 5 pin complete all as specified and directed by Engr In Charge.

Supply and fixing socket outlet multipurpose having provision for 3 pin , 230 volts 15/16 Amp and 3 pin, 5/6 amp piano flush type ISI marked complete all as specified and directed by Engr In Charge.

Supply and fixing switch piano flush type single pole, one way, 230 volts 15/16 Amps ISI marked complete all as specified and directed by Engr In Charge.

Supply and fixing ceiling rose surface bakelite 3 terminals of size 65x25mm complete all as specified and directed by Engr In Charge.

Submain wiring with two single core FRLS insulated flexible copper conductor cable of size 4 sqmm and one single core PVC FRLS insulated flexible copper conductor cable green colour of size 4 sqmm as earth lead in & including concealed PC conduit medium grade cutting chases to walls for laying conduit and making good the distrubed wall surfaces to match with existing specification complete all as specified and directed by Engr In Charge.

Supply and fixing lamp holder polycarbonate insulated body with back plate complete all as specified and directed by Engr In Charge.

Supply and fixing LED box type T/L fitting pre-wired for LED tube with energy efficient LED tube extruded aluminium heat sing & high efficiency diffuser 4 ft version for 16/18 Watts and 16/18 watt LED rod including connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed by Engr In Charge.

Supply and fixing 8 watt wall mounted LED bed side lamp fitting stylish design, craftsmanship, advanced and mature technology, great quality and high brightness bed side reading lamp fitting including 01 Nos of 08 watt LED lamp with suitable size of holder and 2 runs of 1.5 sqmm single core FRLS wire for connecting complete all as specified and directed by Engr In Charge.

Supply and fixing exhaust fan, steel body AC single phase 230V of size 300m sweep with, blades, and frame and louvers including making a hole for fixing of Ex fan with Nutes bolts and civil work also complete all as specified and directed by Engr In Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr In Charge.

Supply and fixing stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed by Engr In Charge.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades and refixing the same after servicing and rectify the minor defects complete all as specified and directed by Engr In Charge.

Material and labour for socket outlet 2 in 1, 6 pin, 5 and 15 amp flush type complete all as specified and directed by Engr In Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V, 1200 mm sweep with brushless direct current motor complete all as specified and directed by Engr In Charge.

Supply and fixing LED light fitting 1x9W/1x10W bulk head luminaires including LED ligh driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr In Charge.

Supply and fixing recess mounted LED fitting with high transmittance polycarbonate diffuser 36 watt fit to 600x 600mm modular/pop/gypsum ceiling complete with including connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over allsheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed by Engr In Charge.

Supply and fixing sheet metal enclosures 240 volt with suitable rated bus bar for double door 8 way IP-43DB's IK-09 suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good distrubed surfaces complete all as specified and directed by Engr In Charge including takin gout old unserviceable MCB DB and removing from site. (MCBs shall be measured and paid separately).

Supply and fixing MCB SP 6 to 32 Amp, 240 Volts, 'B' curve having breaking capacity 10 KA complete all as specified and directed by Engr In Charge.

Supply and fixing MCB SPN 32 Amp, 240 Volts, 'B' curve having breaking capacity 10 KA complete all as specified and directed by Engr In Charge.

Earthing complete with galvanised steel earth plate elecrode 60x60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point complete all as specified and directed by Engr In Charge. Note : (i) Main earthing lead from earth plate electrode to test point upto length7.5 meterslength shall deem to be included in the unit rate quoted against this team. (ii) GI Protection pipe & eathing lead beyond 7.5 meters shall be measured and paid for separately. (iii) On testing after completion if the desired resistenance is not obtained the contractor shall redone the earthing without any extra cost.

M/S SINGH AND ASSOCIATES

dadwal engineers

pardeep singh marwaha

Ashoka Engineers