SPECIAL REPAIR TO ROOF OF BLDG NO P-02, P-03 AND P-17 (RP LINE) AND PROVN OF CERTAIN REVENUE AND MINOR WORKS IN RA AT CAD PULGAON

Amount

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and as directed

Returning, filling in, excavated soil in layers n. exc. 25cm including spreading, levelling ramming and watering in layers n exc 25cm complete all as specified and as directed

Removing excavated soil or materials n. exc. 50m depositing/spreading and levelling where directed at a level not exc. 1.5m above starting point all complete as specified and as directed.

M&L for PCC 1:4:8 type D2 ( using 40mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for Brick work with flyash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

M&L for brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4. complete all as specified and as directed.

M&L for 20mm thick Damp proof course in CM 1:2 to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

M&L for RCC 1:2:4, Type B1 (using 20mm graded stone aggregates) as in roof slabs/beams etc complete all as specified and as directed.

M&L for RCC 1:2:4, Type B1 (using 20mm graded stone aggregates) as in plinth beam lintel beam, roof beams etc. complete all as specified and as directed.

M/L for TMT bars 6 to 8mm dia, Cut to length, bent to shape required including cranking, spirally and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and as directed

All as per item No 10…..but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders complete all as specified and as directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. fair finished surfaces complete all as specified and as directed.

M&L for Moorum/red bajari fillings in floors, pavements and similar works laid in layers n. exc. 15cm Thick, spread, leveled and rammed including watering complete all as specified and as directed.

M&L for Hard core of gauge n.exc 63mm deposited spread and leveled in layers n.exe 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 ( using 40mm graded stone aggregates) as in sub base to floors, pavements and plinth protection etc. complete all as specified and as directed

M&L for 75mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in floor/ plinth protection etc laid in ways finished even and smooth using extra cement complete all as specified and as directed.

M & L for coloured non skid ceramic7 to 8mm thick floor tiles area of each tiles exceeding 0.06 sqm but not exc. 0.11sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to floor including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for glazed coloured ceramic tiles 350x250x7/450x300x7mm thick as in vertical surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 cm thick rendering in cm 1:4 complete all as specified and as directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces finished even and smooth complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:4 on fair faces of concrete surfaces on ceilings finished even and smooth complete all as specified and as directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces finished even and smooth complete all as specified and as directed.

M&L for two coat of cement base paint over a coat of white cement primer or newly plastered surfaces of wall complete all as specified and as directed

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash on walls complete all as specified and as directed.

S & F solid PVC door frame of size 50mmx 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawings complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S & F 100 mm long stainless steel butt hinges complete all as specified and as directed.

S &F vitreous china wash hand basin white flat back of size 550 x 400mm including MS brackets, 32mm dia. brass chromium plated waste coupling with waste pipe complete all as specified and as directed.

S & F low level flushing cistern, 10 ltrs capacity body moulded from design quality high impact poly propylene critical and functioned parts moulded from engineering grade ABS, Nylon and Nylon glass complete including bracket and 15mm bore 450mm long PVC connection in repair including taking down existing flushing cistern complete all as specified and as directed

S & F 15mm dia meter pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered cold with long screwed, shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S & F 15mm dia bib taps cast copper alloy chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S & F 15mm dia chromium plated stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

S & F in repair vitreous china squatting pans Orissa pattern size 580x440 mm white with integral foot rests including provision of lime, concrete, bedding incl re-fixing flushing cistern and flush pipe complete all as specified and as directed.

S & F for 15mm dia medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

All as per Item No 34…... but 20 mm dia

M&L for 15mm dia/bore PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed.

S&F 150mm aluminum anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150 mm aluminum handle Cast type complete all as specified and as directed.

M&L for Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F Rotational moulded polyethylene water storage tanks ) triple layered capacity of 500 ltrs cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part I and as directed.

S&F 15mm Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of for brass ferrule and fixed complete all as specified and as directed.

S & F 75mm bore PVC (SWR) pipes single socket, in any length with rubber ring joint and fixing adhesive, fixed to walls complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe single socket in any length with rubber ring joints laid in tranches or in walls complete all as specified and as directed.

S & F 110mm bore PVC (SWR) bends complete all as specified and as directed.

All as per item No 44….. but 75mm bore complete all as specified and as directed.

S & F 110mm bore PVC (SWR) junction single-Tee (equal or unequal) with access door complete all as specified and as directed.

S & F 75mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S & F 32mm bore HDPE pipes of pressure rating 6kgf/cm2 fixed complete to wall or in floor complete all as specified and as directed.

S & F vitreous china urinal bowl type, white of size 465x355x265mm (min) complete incl providing and fixing plugs, bedding urinals against walls in CM 1:2, screwing urinal to plug with and incl 60mm long brass screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and as directed.

S & F machine cut cudappah stone slab 20.25mm thick polished one side for kitchen platform over cement screed base 15mm thick in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl rubbing and polishing complete all as specified and as directed.

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F chromium plated brass towel rail 20 mm dia 'D' type including fixing with screws to wall 60 cm long complete all as specified and as directed.

Supply only liquid water proofing admixture complete all as specified and as directed.

S&F 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent complete all as specified and as directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm watering and removing surplus soil to a distance not exc. 50 m and making good surface as in soft / loose soil complete all as specified and as directed.

M&L for PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and post hole filling, complete all as specified and as directed.

S & F, fabrications and erections rolled sections as in cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates complete all as specified and as directed.

S&F prepainted galvalume aluminum zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for preparation of New or previously un-treated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

S&F stainless steel frame (grade Schedule 10S) 48 mm with retro reflective tape (Green as on back ground with White Letters upto 8 inches(13CM x 9CM)) pasted on both side aluminum board (4mm thick) as per sizes and dimensions 6ft x 4ft x 7ft pole height complete all as per sketch No 01 to 03, specified and directed by Engr-in-Charge including fwg:- (a) Excavation in post holes each not exceeding 0.50 cum and getting out, returning filling in and ramming earth of broken rubble mixed with earth around in layers not exceeding 25 cm thick watering and removing surplus soil to a distance not exceeding 50 mtrs and making good surface complete. (b) PCC 1:3:6 type C-2 using 40 mm graded aggregate as foundation (size 1.8 m x 1.2m x 450 mm and three coat of white wash complete.

All as per item No 63…… but 3ft x 2.5ft x 6ft pole height complete all as specified and as directed.

All as per item No 63….. But 4ft x 3ft x 6ft pole height complete all as specified and as directed.

M & L for salt-glazed stoneware drain pipes of 150mm bore, laid in trenches and jointed complete all as specified and as directed.

M & L for Concrete bed to drain pipes of 150mm bore, including packing under, and haunching against the sides of pipes after they are laid and tested cement concrete 1:4:8 type D-2 complete all as specified and as directed.

Supply and lay pipe galvanized , "Medium Class", including fittings 20 mm.(3/4'') dia laid in trenches complete all as specified and as directed.

Supply and fix Gun Metal Gate Valves of 20 mm bore complete all as specified and as directed.

Taking down existing water proofing treatment complete of any description from RCC roof slab by scraping by means of MS scrapper patty or by any suitable tools until the concrete surface of the slab visible and removal of rubbish off the premises as directed to a distance not exc 100 mtr all as complete specified and as directed.

M&L for 25mm thick (average thickness) PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregates) laid on roof slab finished even and fair complete all as specified and as directed.

M&L for rendering 10mm thick cement plaster in CM (1:4) mixed with WPC as per manufacturer's instructions laid over roof slab finished even and smooth without using extra cement whilst the concrete is still green complete specified and as directed. Note : WPC compound shall be measured and paid separately.

Supply only Integral water proofing compound ISI mark complete all as specified and as directed.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) all as specified and as directed.

M&L for APP polymeric water proofing membrane 3.00 Kg per sqm and min 3 mm thick reinforce with polyster non woven fabric (wt not less than 150 gms/sqm) laid over roof surface with 100 mm over lap and including vertical surfaces upto required height and tucking into grooves and sealing complete with thermo fusion, torch application over compatible bitumen primer at 0.40 ltr/sqm including cleaning surfaces all as instructed as per manufacturer complete all as specified and as directed.

Taking down Pressed cement concrete tiles incl 15mm thick bedding mortar in CM 1:4 complete all as specified and as directed.

S & F Hydraulically pressed cement concrete tiles in roof floor exc 0.06 sqm, n.exc 0.11sqm and thickness 22-25mm as decided, machine pressed laid over 15mm thick bedding mortar in CM 1:4 having joint of tiles 2-3 mm wide set jointed and pointed with chemical like Tile-grout or equivalent as approved by GE complete all as specified and as directed.

M&L for in repairs for providing PCC type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, Complete all as specified and as directed.

M & L for 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth with out suing extra cement using WPC as per manufacturing instruction Complete all as specified and directed.

M & L for 10mm thick rendering on fair faces of brick work or concrete surface in cm 1:6 to be finished even and smooth with out suing extra cement Complete all as specified and as directed.

M & L for rendering 5mm thick in CM 1:3 and finish the surface even and smooth without using extra cement as in ceiling, soffits of slab complete all as specified and as directed.

M & L for two coats of distempering walls with distemper oil emulsion over a coat of chalk whiting on newly plastered wall surfaces including preparation of Priming plastered and other surfaces with alkali resistant priming paint surfaces complete all as specified and directed.

Complete removal of existing treatment on old surfaces on walls and applying two coats of distempering on walls with distemper oil emulsion over a Priming plastered and other surfaces with alkali resistant priming paint complete all as specified and as directed.

M & L for complete removal of existing treatment on old surfaces on ceiling two coats of white wash on old surfaces on ceiling including preparation of old surfaces.

M & L for complete removal of existing treatment on old surfaces on walls two cement base paint over a coat of white cement primer including preparation of old surfaces.

M&L for point wiring complete with 1.5sqmm single core sheathed PVC insulated FRLSH cable 1100 V grade multistranded copper conductor of different code of ISI marked drawn through and including PVC casing capping of suitable size with accessories ISI marked incl PVC insulated copper cable for earth of same type and sized connected to earth dolly including provision of PVC box of suitable size for mounting switches / sockets and fan regulators etc complete all as specified and directed for the following:-

One light point controlled by one switch one way

One ceiling fan / exhaust fan / wall mounting fan point controlled by one switch one way

M&L for switch piano flush type single pole, one way, 5 Amps, 240 V complete all as specified and directed. Make : Anchor/Leader/Cona

S&F ceiling rose polycarbonate type with 3 terminals complete all as specified and as directed. Make : Anchor/Leader/Cona

S&F LED tube light lamp 1 x 18/20 watt retrofit including suitable size of batten complete (01 set) (single / double side connection) all as specified and as directed . Make Havells /Philips/Bajaj .

S&F in replacement of sheet steel enclosure with single door flush mounting for MCB DB SPN 4 ways,240 volt factory fitted rated bus bars, earth bar, neutral links complete incl. blanking plates as required & making good the disturbed surfaces complete all as specified and as directed. Make : Havells/legrand/Schneider

S&F in replacement of MCB SPN 06-32 Amps 240V ,50 Hz ,breaking capacity 10 KA," C " series complete all as specified and as directed. Make:Havells/Legrand/Schneider

S&F in replacement of MCB SP 06-32 Amps 240V ,50 Hz, breaking capacity 10 KA," C " series complete all as specified and as directed. Make:Havells/Legrand/Schneider

Material and Labour for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of earth plate not less than 1.5m below ground level connected to galvanized iron earth lead wire 4.00mm dia by means of bolts, nuts, check nuts, washers of galvanized iron and connected to main switch/control board upto 7.5m away from the earth electrode including excavation earth work, PCC chamber, RCC cover slab char coal, watering pipe 20mm bore light grade, wire mesh lugs, earth lead protection pipe 15mm bore, medium grade upto 7.5m long as applicable and as per plate No. 3 of SSR Part-I 2009 and all as specified. Notes-Quoted rates shall be includes fwg;- (a) Excavation and earth work in any type of soil. (b) Drilling of holes in electrode (c) PCC pit in cement concrete (1:2:4) type B (d) 40 mm thick Pre-cast RCC cover or reinforcement with 8mm TMT bars at 100mm c/c bothways with suitable handle. (e) Funnel with watering pipe of GI 20 mm nominal bore light grade & copper lug etc. (f) 15mm nominal bore medium grade GI protection pipe upto 7.50 m long for protection of earthing lead. (g) Requisite quantity of charcoal and common salt. (h) Connection to earthing test point and testing on completion.

Supply and fix of exhaust fan heavy duty AC single phase 230/240 V of size 300mm sweep with louver complete all as specified and as directed Make- Havells,Bajaj, Crompton

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminum conductor of size 6.0 sq mm 2 core complete all as specified and as directed.

Supply and lay, dry river sand filling in trenches to required width at bottom and top of cable as cable cushioning including spreading, leveling, watering and consolidation complete all as specified and as directed.

Supply and lay un-reinforcement precast concrete cable cover, class LV, type 1, flat of size 250 X 150 X 40mm for LT cable and laid dry in trenches over underground cables complete all as specified and as directed.

Supply and lay pipe galvanized, “Medium class”, including fittings 25 mm dia (Cable Protection Pipe) fixed to walls and ceilings or laid in floors complete all as specified and as directed.

M/S L M Chourasia

RAJ ENTERPRISES

M/S Ramakant Chourasia

MAHARASHTRA ENTERPRISES

Ankit Construction

Bidder Name

M/S L M Chourasia

Ankit Construction

RAJ ENTERPRISES

M/S Ramakant Chourasia

MAHARASHTRA ENTERPRISES

Arnav Enterprises