Repair to fencing, compound wall, paths, hard standing and connected B/R work and cleaning of service water tanks in OTM ILP//KLP and married Accn under AGE B/R-I at GE (A) Suratgarh Mil Stn

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) not otherwise specifically provided for in this Schedule, complete all as specified & as directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion in concrete, brick work, masonry etc and making good disturbed ground complete all as specified and as directed.

Dismantling chain link fencing wire mesh, any type from any position complete all as specified and directed.

Dismantling fencing barbed wire, any type from any position complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets as in roof coverings etc including ridges complete all as specified and as directed.

Dismantling of cast iron, wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule (BOQ), complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil complete all as specified & as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete in post holes complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in foundations, filling and mass concrete, raft footing, foundation beam, plinth beam, kerb block, base for columns etc complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in copings, roof kerbs and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L for plastic dividing strips, 1.5mm thick and 38mm wide fixed in cement concrete floor complete all as specified and directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately under respective item of this Schedule.

M&L for precast RCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in window or door cills, lintels, post, boundary pillars, landings, with plain fair faces including chambers, weatherings, throating etc and setting in CM (1:4) including formwork as required complete all as specified & as directed.

M&L for precast cement concrete (1:2:4 type B0 using 12.5mm graded crushed stone aggregate) louvers and jallies, 35mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 complete all as specified & as directed.

M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exceeding 6.00 metre mean radius, built in cement and sand mortar 1:6 complete all as specified and as directed.

All as per serial item No 19.00 here-in-before but except bricks complete all as specified and as directed. Note : Old serviceable burnt clay / fly ash bricks retrieved from serial item No. 5.00 here-in-before shall be used under this item.

M&L for brick work with old size burnt clay sub-class 'B', straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

S&F rolled mild steel as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length directed) and similar work conforming to Grade E-250 quality `A’ complete all as specified and as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified & as directed.

S&F mild steel work as in fencing posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Grade E-165 (Fe 290), complete, all as specified & as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 60mm long and dia of neck 5 to 10 mm complete all as specified & as directed.

Fixing only mild steel galvanized chain link fencing, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire complete all as specified and as directed. Note :- Supply only chain link fencing shall be measured and paid for separately.

Supply only mild steel galvanized chain link fencing, any size or type as directed complete all as specified and directed. Note:- (i) Flat iron, round bars, nut bolts and washer shall be measured and paid for separately. (ii) The weight of chain link fencing shall be ascertained by BOO as ordered by GE and payment shall be made accordingly. BOO duly counter signed by GE shall be enclosed with final bill.

S&F mild steel round bars 8 to 10mm dia as in tie bars fixed to fencing posts including cut to length, bent to shape, welding of bar at spots as directed and other similar works, conforming to Grade E-165 (Fe 290), complete all as specified & as directed.

M&L for Galvanised 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins complete all as specified and directed. Note:- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment.

M&L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed.

S&F Pre-painted galvalume aluminium zinc coating corrugated steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & as directed. Note : Colour of sheet shall be as approved by the GE.

S&F Pre-painted galvalume aluminum zinc coating Plain steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/ridge/fascia/cladding to wall, fixed with self tapping screws complete all as specified & as directed. Note : Colour of sheet shall be as approved by the GE.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even, complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4) type B1 using 20mm graded crushed stone aggregate as in flooring, leveling course, etc, surface finished fair and even without using extra cement complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring, leveling course/sub base surface finished fair and even, complete all as specified and as directed.

M&L for factory made glossy finish chequered cement concrete tiles, 25cm x 25cm x 20mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.

M&L for Heavy duty parking coloured tiles, 25cm x 25cm x 10mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed.

M&L for factory made rubberised 60mm thick machine pressed precast cement concrete coloured designer polished (reflecting type) interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment with coloured top casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape & colour of paver blocks shall be as approved by the GE.

M&L for factory made rubberised 80mm thick machine pressed precast cement concrete coloured designer polished (reflecting type) interlocking paver blocks of Grade M-40 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment with coloured top casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape & colour of paver blocks shall be as approved by the GE.

M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection/ hard standing surface finished even and smooth without using extra cement complete all as specified and directed. Note :- Plinth protection/hard standing shall be of width as directed and shall be laid with an outward slope of 1:30 in alternative bays not exceeding 4 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for rought cast plaster in two layer on fair faces of brick masonry or concrete surfaces of walls consisting of 1st layer not less than 10mm thick plaster in CM 1:3 and 2nd layer (setting coat or top layer) of Rough cast mixtrue consisting of crushed stone or fine gravel aggregate size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 complete, all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for preparation of old surfaces (plastered or unplastered) of walls including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint complete all as specified & as directed.

M&L for preparation of old decorated plastered or unplastered surfaces and applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant priming paint on walls complete all as specified and as directed.

M&L for preparation of old previously treated plastered/unplastered surfaces of any description over 10cm girth or width, not otherwise described including filling of cracks and applying one coat of acrylic emulsion paint of approved shade/tint complete all as specified & as directed.

M&L for preparation of old plastered /concrete surfaces of kerb stone alongwith road sides any description over 10cm width or girth and applying two coats of synthetic enamel paint in alternate panel with different colour of approved complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description not exc 10cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for high intensity grade retro reflective 3m (HIP) sheeting/tape and reflecting new retro reflective sheet as per sample and colour approved including writing letters/numurics of height not more than 30cm and width not more than 30cm, cut out of retro reflective sheet colour as decided and pasting the same on old stainless steel sheet/ new steel sheet/ fibre sheet of sign board and including tanking down old sheet where required and preparation of surfaces as per manufacturers instructions complete all as specified and directed.

Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 15mm bore complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 15mm bore obtained serviceable vide serial item No. 50.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed. Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.

Dismantling carefully and taking up or down existing unserviceable/serviceable steel water tubing and connections of 20mm bore complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Fixing/Laying only, jointing and testing old serviceable galvanized steel water tubing medium grade of 20mm bore obtained serviceable vide serial item No. 53.00 here-in-before including cleaning the pipe from inside & outside properly including rust & mud removal, with & including new fittings and fixed to walls and ceilings or laid in floors in new or old position complete all as specified and as directed. Note : The quoted rate shall deemed to include new GI fittings (ISI marked). Old fittings shall not be used.

Supply and fixing in replacement of HDPE PVC lid cover for 500 Litre capacity Rotational moulded polyethylene water storage tanks complete as specified in SSR Part-I and as directed.

Supply and fixing in replacement of HDPE PVC lid cover for 1000 Litre capacity Rotational moulded polyethylene water storage tanks complete as specified in SSR Part-I and as directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed.

Disconnecting existing serviceable rotational moulded polyethylene water storage tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity exc 250 litres & not exc 500 litres including cleaning & removing all scale & dirt etc from tank with gunny bags, cleaning with fresh water and bleaching powder, complete all as specified and as directed.

Disconnecting existing serviceable rotational moulded polyethylene water storage tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position of capacity exc 500 litres & not exc 1000 litres including cleaning & removing all scale & dirt etc from tank with gunny bags, cleaning with fresh water and bleaching powder, complete all as specified and as directed. Note for serial item No. 60.00 & 61.00 of BOQ : Quoted rate shall deemed to include supply & fixing of small fitting such as tank nipple, socket, union etc as required and marking of cleaning date over the water tank as directed by Engineer-in-Charge

S&F in repairs Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S&F in repairs 15mm bore stop valve of PTMT, any colour high pressure screwed for iron pipe and fixed (minimum weight 90gms) complete all as specified & as directed.

S&F in repairs 20mm bore stop valve of PTMT, any colour high pressure screwed for iron pipe and fixed (minimum weight 92gms) complete all as specified & as directed.

S&F in repairs 15mm bore Gun metal, globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

S&F in repairs 20mm bore Gun metal, globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

M&L for preparation of new steel and iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M/S BUDHRAM BISHNOI

PACHAR BROTHERS

M/s BHUPINDRA ENGINEERING WORKS

MSR INFRATECH

M/S MANIRAM BISHNOI

M/S KARNI CONSTRUCTION COMPANY