Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi

Name of Work :- Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No. :- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

General Notes :-

1) Wherever old material/works are replaced with new one, quoted rate includes removing/dismantling the existing one and depositing the serviceable material at departmental store and disposing off debris outside the guest house premises.

2) The Agency shall take care of existing service and other department properties while carrying out job & if any damage is done agency shall get it repair on his own cost.

3) The above quoted rates shall be inclusive of all taxes, duties, levies, insurance, installation, transportation costs etc and also includes provision of all necessary manpower, tools etc. for carrying out this work in effective manner.

4) The contractor shall issue I-Cards to his workers deployed on regular basis.

5) Approved Samples of Materials: The contractor shall produce samples of all materials at least two weeks before incorporation in the work and shall obtain approval of these in writing from the Engineer-in-charge, before he places bulk order for the materials.

6) Protection of work: The contractor shall be responsible for the temporary doors and closing in opening necessary for the protection of the work during progress. He shall also provide and maintain any other temporary substitute for this purpose.He shall takes all the necessary precautions to prevent damage to all the works till its handing over.

7) All dismantling work shall be done with careful manner.

8) Contractor shall take all precautions to cover all computers, printers, monitors etc., glass and windowpanes to prevent damage. Damage, if any shall be made good at no extra cost to department.

9) All stone flooring to be protected by 15mm POP covering with plastic base.

10) The rate shall include wastage of material and labours.

11) All safety & security regulations shall be followed strictly as per specifications & conditions of contract.

12) Tenderers are advised to visit the site of work with prior permission of Engineer- in- Charge/ authorised representative to acquaint themselves and understand the nature of work particuraly for items covered under this Tender and location of work before quoting tender.

13) The contractor shall provide a sleeveless Jacket to the workers in pattern, colour showing name of contractor with address and telephone number as approved by the Engineer in charge. All the workers must wear the same while on duty.

14) Contractor shall take Contractor’s All Risk (CAR) Insurance Policy in respect of entire scope of work for entire period of contract and copy of the same shall be submitted to the EIC before commencement of the work. The insurance policy shall be taken before commencement of the work and shall be renewed during the construction period till actual completion of work. The charges for issue & renewal of insurance policy shall be borne by Contractor. In event of failure of the Contractor to obtain CAR Insurance Policy, Running Account Payments of the Contractor shall be withheld till such time the same is obtained by the Contractor & submiited to the EIC. In case, CAR Insurance Policy has validity period not matching with contract period (either due to policy start date later than actual date of start of work or policy end date earlier than actual date of completion), then penalty for gap in period shall be levied at one and half times the rate of Insurance Policy premium including GST, to be computed on per day basis.

15) The agency has to abide by the "Construction & Demolition" work management plan as approved by MCD & any other requlations issued by the statutory authoritites in the matter from time to time. The contractor shall take necessary permisiion from statutory authorities for dumping the debris/excess earth outside department premises.

16) Water will be supplied by department and water charges will be recovered @1% of gross value of work done. Electricity for work will be supllied by department @ free of cost.

17) The all furniture items such as (table, chair, cupboard etc.) shall be similar to photographs, drawings, sketch provided with tender documents. The agency requested to acquint themselves with specification before quoting rates.

PART - II : PUBLIC HEALTH ENGINEERING WORKS

General Notes :-

1) Tenderers are advised to visit the site of work, acquaint themselves about the levels of sub soil water, drainage facility for dewatering, accessibility to site etc. and quote the rates accordingly.

2) All PH materials, water supply, sewer, sanitary wares & CP brass fittings & fixtures, etc., shall be of first quality with ISI mark (unless otherwise specified) and shall be of the make as per the latest approved list of manufacturers of DCSEM as well as shall be of make as per the latest approved list of materials of local Statutory body if required. They shall be got approved by the Engineer- in- charge before incorporating in the work.

3) All sanitaryware shall be provided from same brand.

4) All CP fittings / Fixtures shall be provided from same brand.

5) All the items of work which are to be carried out below the ground level involving earthwork excavation, the contractor shall bear the cost of Shoring / dewatering during the progress and till the completion of work.

6) The rate for the items such as sanitary wares, CP brass fittings, GI / CI / PE / PPR / CPVC / uPVC / SWR pipes which are to be fixed on the walls / dado, floors etc. includes the cost of fixing materials and matching colour cement required for reinstating the surface to the entire satisfaction of the EIC.

7) All the items include testing after completion of the Work.

8) In case of any item, in spite of its non - availability in the tender is required to be operated under a particular part of schedule of quantities, the same shall be paid under the similar / relevant item of any other part.

9) Concealed / underground GI pipe line is to be wrapped with Pypekote corrosion protection tape.

10) The excavated / transported materials shall be stacked at convenient places before spreading, filling & compacting at required locations.

11) Specification for Bricks shall be read as class designation 35.

12) Support pedestals at terrace will be paid under relevant civil item.

13) All thermoplastic piping at terrace after completion, testing and commissioning of work shall be painted with water based distemper to avoid direct exposure to sunlight. No extra charges will be paid for the same.

Name of Work :- Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No. :- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

FURNITURE DETAILS

Sr. No. Item Desription Size (mm) Reference Image

A-1) Dining Table 1200 760 750

A-2) Dining Chair (without hand rest) (Back rest additional as per design) 450 450 450 to 500

A-3) Study/Writing Chair (with hand rest) (Back rest additional as per design) 600 550 450

A-4) Study/Writing Table 1140 500 750

A-5) Side Table 600 mm Dia (Similar to refernce image) 450

A-6) Centre Table 750 750 500

A-7) Bed Side Table 450 450 450

A-8) Glass Mirror 1200 750 -

B-1) Study/Writing Chair (with hand rest) (Back rest additional as per design) 600 550 450

B-2) Study/Writing Table 1200 500 750

B-3) Coffee Table Chair (Back rest additional as per design) 600 550 450

B-4) Coffee Table 600 mm Dia (Similar to refernce image) 500

B-5) Bed Side Table 600 450 450

B-6) Glass Mirror 1200 750 -

C) For Conference Room

C-1) Main Door - 1650 2000

D) Miscellaneous

D-1) Single bed 6.5 feet 3 feet -

Select, Excess (+), Less (-) Less (-)

Tender Inviting Authority: Chairman GB

Name of Work: Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No. :- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

0 ABSTRACT OF COST

1 PART-I : CIVIL WORKS 0.000 Nos Excess(+) Full Conversion INR

2 PART-II : PUBLIC HEALTH ENGINEERING WORKS 0.000 Nos Excess(+) Full Conversion INR

3 PART-III : ELECTRICAL WORKS 0.000 Nos Excess(+) Full Conversion INR

4 PART-IV : CCTV WORKS 0.000 Nos Excess(+) Full Conversion INR

5 PART-V : REBATE FOR TAKING AWAY (DEDUCT) 0.000 Nos Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Select, Excess (+), Less (-) Less (-)

Tender Inviting Authority: Chairman GB

Name of Work: Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No. :- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

100 PART - I : CIVIL WORKS

101 Providing & fixing in position suspended false ceiling system using 600 x 600 mm Calcium Silicate Ceiling tiles (M/s. Aerolite Ceiling Systems) having 15 mm densified edges and 100% humidity resistance, non combustible as per BS476 part IV with thermal conductivity of 0.043 w/m KC and approved surface design and edge profile (Tegular/ Spintone) placed in a suspended grid of size of 600 x 600 mm made of hot dipped G.I. steel sections having an exposed surface capping of pre-finished baked polyester painted coil where in the main tee of size 24mm x 38mm x 0.33mm shall be suspended at 1200mm centres along the length of ceiling with 4 mm dia G.I wire with necessary level adjusters and cross tees of size 24x 28 x 0.33mm x 1200 mm shall be inserted in to slots between the main tees at 600 mm centres and there after in direction vertical to the longer tees of size 24 x 28 x 0.33 mm x 600mm shall be inserted to form a grid size of 600 mm x 600 mm resting on the periphery walls on wall angles of size 22mm x 22mm x 300mm x 0.40 mm thickness etc. complete as per specifications, drawings and as directed by the Engineer-in-Charge. Note:- The entire grid system shall be designed to bear a distributed load of minimum 15 kg/sqm. The rate shall include providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings. The work shall be carried out as per directions of Engineer-in-charge. (Only calcium silicate false ceiling area will be measured for the purpose of payment) (M/s. Aerolite False Ceiling Tiles of Models Fine Fissured, Cosmos / Spintone / Hexa / Quadra with micro look system) 0.000 Sqm Excess(+) Full Conversion INR

102 Providing and fixing in position suspended false ceiling system using 12 mm thick calcium silicate boards (M/s. Hilux Ceiling Systems), 100% humidity resistance, non combustible as per BS476 part IV with thermal conductivity of 0.043 w/m KC placed in a suspended grid of size of 600x 600mm made of hot-dipped G.I steel sections wherein the ceiling sections of 0.55 mm thick shall be suspended at 1200 mm centres along the length of ceiling with 4mm dia G.I wires/ 1 mm thick strip hangers made of G.I sheet sections with necessary level adjusters and inter channels of 0.90 mm thick with connecting clips and resting on the perifery walls on wall angles of 0.55 mm thickness including providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings and as per directions of Engineer-in-charge. The main tees to be suspended from the ceiling/ soffit with the help of metal dash fastners of 6mmx50mm, soffit clits of 25mmx35mmx1.60mm and 4mm dia G.I wire with galvanised spring steel levelling clips/ G.I strip Hangers at 600mm centers . the entire grid system shall be designed to bear a distributed load of minimum 25 kg/Sqm (Only calcium silicate false ceiling area will be measured for the purpose of payment) 0.000 Sqm Excess(+) Full Conversion INR

103 Providing and fixing marine ply (BWP Grade) confirming to IS:710 of approved make and manufacturer for Fridge Cabinate, Luggage Cabinate & Shoe rack, Overhead Storage Unit, Wall panelling, Cupboard and other furniture works at all floors, levels and location as shown in drawing including all labour, Cutting, Wastage, Sizing, adhesive, SS screws, nails, Rawl plug, scaffolding etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. Note : 1) Cladding/panneling /Furniture shop drawings shall be submitted by the agency and got approved by EIC before start of manufacturing works. 2)The rates shall include all the required other materials like, nails, SS screws, wooden nails, Adhesive Glue ,all required heavy quality fixtures and fittings etc. and labour, scaffolding etc.

103.01 19 mm thick 0.000 Sqm Excess(+) Full Conversion INR

103.02 12 mm thick 0.000 Sqm Excess(+) Full Conversion INR

104 Providing and fixing 3 mm thick superior quality wood veneer of approved type for Fridge Cabinate, Luggage Cabinate & Shoe rack, Overhead Storage Unit, Wall panelling, Cupboard and other furniture works at all floors, levels and location as shown in drawing including all labour, Cutting, Wastage, Sizing, adhesive, scaffolding etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. 0.000 Sqm Excess(+) Full Conversion INR

105 Providing and fixing 1.0 mm thick decorative/plain, high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality, lamnation of approved make and manufacturer having approved colour, shade, texture, finish for Fridge Cabinate, Luggage Cabinate & Shoe rack, Overhead Storage Unit, Wall panelling, Cupboard and other furniture works at all floors, levels and location as shown in drawing including all labour, Cutting, Wastage, Sizing, adhesive etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. 0.000 Sqm Excess(+) Full Conversion INR

106 Supplying and fixing following type of approved premium quality miscellaneous fittings, fixtures and fastenings, having Gold / Brass finish along with necessary SS screws, bolts, nuts, washers, wooden packing pieces if necessary etc and other standard accessories, including making necessary recess complete all as per specifications and as directed by the Engineer-in-Charge. Note for fixtures and fittings: i) One sample board consisting of each item of schedule of quantities with approved quality fittings & fixtures & necessary accessories including chromium plated brass screws, bolts, nuts, washers should be submitted for approval of Engineer-in- charge. Large scale procurement shall be taken up only after approval of the Engineer-in-charge. After approval, the samples shall be kept in the office of the Engineer-in-charge to ascertain the approved quality for the entire work. ii) All fittings & fixtures shall conform to relevant IS code.

106.01 Supplying cold rolled stainless steel soft close drawer telescopic ball bearing channel runner approx up to 600mm long of approved make including necessory stainless steel screws 0.000 One Set Excess(+) Full Conversion INR

106.02 SS fancy handles with back plate having approx size upto 150mm long 0.000 Each Excess(+) Full Conversion INR

106.03 SS hanger rod with both end brackets having 25 mm dia and 1.25 mm wall thickness heavy quality 0.000 RM Excess(+) Full Conversion INR

106.04 Stainless steel Box type soft close spring hinges heavy duty cabinet hinges of approved make for cabinet, cupboard and storage unit etc ( at 0 degree hinges, Hydraulic type) 0.000 Each Excess(+) Full Conversion INR

106.05 SS supports for shelfs with SS threaded/ notch type pins of suitable length for horizontal shelves 3 on each side & 2 at back side for each shelf. 0.000 Each Excess(+) Full Conversion INR

106.06 S. S. Tower bolt 250 mm long x 12 mm barrel 0.000 Each Excess(+) Full Conversion INR

106.07 S. S. Tower bolt 150 mm long x 12 mm barrel 0.000 Each Excess(+) Full Conversion INR

106.08 S. S. Door stopper with twin-rubber bushing (shutter mount type) 0.000 Each Excess(+) Full Conversion INR

106.09 SS fancy handles with back plate having approx size 250mm long 0.000 Each Excess(+) Full Conversion INR

SS fancy drawer knob plate having approx size 50mm 0.000 Each Excess(+) Full Conversion INR

106.11 Piano Hinges 19mm x 19mm x 1 mm 0.000 RM Excess(+) Full Conversion INR

106.12 SS But hinges (Heavy Weight), IS:12817 of size (125 X 64 X 2.5 mm) 0.000 Each Excess(+) Full Conversion INR

106.13 SS coat hanger made using 3 mm dia wire having 350 mm minimum length 0.000 Each Excess(+) Full Conversion INR

107 Supplying and fixing Bright finished brass cupboard or Wardrobe lock with four levers & duplicate keys of approved make and brand including necessory screw (50 mm size) 0.000 Each Excess(+) Full Conversion INR

108 Providing 10mm dia Solid Stainless Steel Bars (SS-304 grade) having gold color and approved finish and fixing over luggage and shoe rack and including all labour, Cutting, Wastage, Sizing and including making both ends suitably sloping to avoid damages to luggage etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. 0.000 RM Excess(+) Full Conversion INR

109 Provding and fixing in position gold color finished Stainless Steel (SS-304 grade) fixed louver type fins for ventilation on both faces of opening having (approx size 300 X 250 mm and minimum 2mm thick SS Sheet), including all labour, Cutting, Wastage, Sizing, making opening etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. 0.000 Sqm Excess(+) Full Conversion INR

110 Providing & fixing in position approved, best and premium quality Burma Teak Wood (BTC) for wall panelling, lipping, moulding and other furniture work at all floors and levels as per drawing including providing and fixing S.S. screws, nails, cutting, moulding, sizing, wastage, labour, adhesive, scaffolding etc. all complete as per specification & drawings and as directed by Engineer-In-Charge.

110.01 Burma Teak Wood (BTC) for wall panelling and other furniture works. 0.000 Cum Excess(+) Full Conversion INR

110.02 Burma Teak Wood (BTC) for lipping all round shutter & Z shape at meeting style of shutter having approx size 20 mm thick and approx 25 mm wide. 0.000 RM Excess(+) Full Conversion INR

110.03 Burma Teak Wood (BTC) for architraves (having approx size 25 X 25 mm with half round moulding) for cupboard work. 0.000 RM Excess(+) Full Conversion INR

110.04 Burma Teak Wood (BTC) for decorative bidding (having approx size (50 X 50 mm/ 60 X 40 mm) with moulding as per drawing) for Fridge Cabinate, Wall panelling, conference rom, etc. 0.000 RM Excess(+) Full Conversion INR

110.05 Burma Teak Wood (BTC) for decorative bidding (having approx size 30 X 20 mm with moulding as per drawing) for Wall panelling, etc. 0.000 RM Excess(+) Full Conversion INR

110.06 Burma Teak Wood (BTC) for furniture work including all the decorative and Carving works as per detailes, design and drawing for Wooden ledge for TV unit legs, table legs and frame 0.000 Cum Excess(+) Full Conversion INR

110.07 Burma Teak Wood (BTC) for decorative bidding (having approx size 50 X 75 mm with moulding as per drawing) for Conference room & Conference table, etc. 0.000 RM Excess(+) Full Conversion INR

110.08 Burma Teak Wood (BTC) for decorative bidding (having approx size 100 X 75 mm with moulding as per drawing) for Conference room, etc. 0.000 RM Excess(+) Full Conversion INR

110.09 Burma Teak Wood (BTC) for decorative bidding (having approx size 100 X 75 mm with moulding as per drawing) for Conference room, etc. fixed in profile of semicircular/parabolic shape 0.000 RM Excess(+) Full Conversion INR

111 Providing and fixing 19 mm thick Block board Marine grade (BWP Grade) confirming to IS:1659 of approved make and manufacturer for cupboards and cabinate shutters (sinhle/double leaf), at all floors, levels and location as shown in drawing including all labour, Cutting, Wastage, Sizing, adhesive, SS screws, nails, scaffolding etc. all complete as per specifications, drawing and as directed by Engineer-In-Charge. (Note: The entire shutters shall be jointless.) 0.000 Sqm Excess(+) Full Conversion INR

112 Providing & fixing at all levels, locations & floors the carpentary fittings as mentioned below using approved quality, make, shape, size, patterm material including all labour, SS screws, washers, nut bolts, rawl plug, wastage etc complete all as per drawing, specifications and as directed by the Engineer-in-Charge.

112.01 Magnetic catcher having double strip, 40 mm size horizontal / vertical type for cupboard, ward robe shutter etc. 0.000 Each Excess(+) Full Conversion INR

113 Providing and fixing in position machine cut and machine pre polished (mirror finish) 18mm thick granite stone (of approved color and shade) band of 100 mm/200 mm (approx) width over existing flooring including necessary epoxy resin based adhesive (Araldite), cutting, labour, wastage and including half round moulding and polishing of both edges etc. complete all as per drawing, specification and as directed by the Engineer-in-Charge. 0.000 Sqm Excess(+) Full Conversion INR

114 Providing and fixing in position 8mm thick toughened float glass with crystal edge polish using glass of approved make and brand fixed with SS-304 patch fittings including making necessary holes (wherever required for fittings) etc complete all as per specifications, drawings and as directed by the Engineer in Charge. (Note:- The cost of work is inclusive for any SS patch fittings required for fixing glass in wall & floor. Glass area alone shall be measured and paid) 0.000 Sqm Excess(+) Full Conversion INR

115 Providing 10mm wide Solid Stainless Steel T-Patti (SS-304 grade) having gold color and approved finish and fixing over existing door and including all labour, Cutting, Wastage, Sizing and including making necessary notch for fixing etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. 0.000 RM Excess(+) Full Conversion INR

116 Providing and fixing 18 mm thick Composite Marble (Synthetic Marble) of approved, make, brand, colour, shade, finish, texture (similar to Gold Rush, PL-191 of M/s. Specta), mirror polished, premoulded and prepolished, machine cut for Fridge Cabinate, Wooden ledge for TV Unit, Table, Wash Basin Counter etc. of required size (in single piece only), at all floors, levels & locations including rubbing, moulding and polishing to edges to give high gloss finish etc complete all as per drawing, specifications and as directed by the Engineer-in-Charge. (Note : The rate shall be inclusive of providing and fixing of 36 to 50 mm moulding edges wherever required as directed and as per drawing.)

116.01 Placing over fridge cabinate etc. 0.000 Sqm Excess(+) Full Conversion INR

116.02 Placing and fixing over Wooden ledge for TV Unit, Table, conference counter etc. including necessary high quality resin based adhesive suitable for fixing of composite marble over ply/wood etc. The rate shall be inclusive of providing and fixing moulding edges (36 to 50 mm) on exposed edges as per drawing. 0.000 Sqm Excess(+) Full Conversion INR

116.03 Providing and fixing in position Wash Basin Counter of sandwich type having topping of 18mm thick composite marble and bottom of 35mm thick Cuddapha stone total sandwich thickness with 1:4 (ready mix cement mortar) will be 100mm thick in single piece including making recess in wall, fixing with necessary cement mortar and making good the surface and including rubbing, half round moulding and polishing to edges to give high gloss finish Note : Only top clear exposed area of the combined sandwich system shall be measured for payment. 0.000 Sqm Excess(+) Full Conversion INR

116.04 Providing and fixing in position facia for Wash Basin Counter having thicknesss of 18mm thick composite marble and fixing with epoxy based resin adhesive (Araldite) having approx width of 100mm thick in single piece and including rubbing, half round moulding and polishing to edges to give high gloss finish 0.000 Sqm Excess(+) Full Conversion INR

116.05 Providing and fixing in position Wash Basin Counter vertical support of sandwich type having both side facing of 18mm thick composite marble and middle of 35mm thick Cuddapha stone total sandwich thickness with 1:4 (ready mix cement mortar) will be 100mm thick in single piece including making recess in wall, fixing with necessary cement mortar and making good the surface and including rubbing, half round moulding and polishing to edges to give high gloss finish Note : Only clear exposed area of the combined sandwich system shall be measured for payment. 0.000 Sqm Excess(+) Full Conversion INR

117 Dismantling / demolishing work by manual /Chiselling/ mechnical means, carefully without damaging & disturbing adjacent structures, at all levels, locations & floors including labour, machine, loading, unloading, transportation, stacking of serviceable material at directed place & disposal of debris & unserviceable material outside Dhruva Guest House at approved Municipal dumping ground and including scaffolding etc. complete all as per specifications and as directed by Engineer-in-Charge.

117.01 Brick & Stone masonry work in cement mortar including cement mortar plastering / pointing work, Plain Cement Concrete (PCC), Reinforced Cement Concrete (RCC) including cutting of steel reinforcement bars (by cutter, gas welding etc.), Flooring, Plastering 0.000 Cum Excess(+) Full Conversion INR

118 Cement plaster in single coat with Ready mix cement mortar 1:4 at all floors, heights, slopes and locations on plain or curved surfaces including rounding wherever required including to prepare the surface even and smooth to correctline, level, plane, neat cement punning and plumb including scaffolding, curing etc. complete as perspecifications, drawings and as directed by the Engineer in charge.

118.01 6 mm thick cement plaster in ready mix Cement mortar(1 cement : 4 fine sand) for , exposed concrete surfaces, soffits of all slabs and beams soffit of staircase waist slab etc. internal brick /concrete surfaces. 0.000 Sqm Excess(+) Full Conversion INR

118.02 15 mm. thick plaster in ready mix CM 1:4 mix for internal brick / concrete surfaces for all walls and beams flush with walls, mullions etc. 0.000 Sqm Excess(+) Full Conversion INR

119 Providing and applying 1.5 mm thick white cement based wall care putty in two coats of approved make, at all floors, levels and locations, over plastered surfaces finished smooth to correct line, level, plane, plumb etc., including preparing the surfaces, scaffolding smoothen the putty surfaces with very fine water proof emery paper to get a glossy finish etc. complete as per specifications, as per manufacturers specifications, drawing & as directed by the Engineer-in-charge. 0.000 Sqm Excess(+) Full Conversion INR

120 Providing & applying premium acrylic emulsion (plastic) paint for internal plastered surfaces and over false celling in two or more coats on old / new surfaces at all floors, levels & location using ready mixed & ready made acrylic emulsion paint of approved make and shade including one coat of approved cement / acrylic primer (water thinnable) including labour, material, scaffolding, surface preparation, cleaning etc complete all as per specifications and as directed by Engineer-in-Charge. (Note:- Premium Acrylic emulsion shall have VOC content less than 50 grams/ litre) Note : Including thoroughly scrapping, removal of old paint, if any, sand papering & preparing the surfaces, etc, necessary covering material (tarpaulin etc), cleaning, removal of splashing & droppings of floors, wall, ceiling, doors & windows etc & disposing of debris at directed place.

120.01 Two coats of premium interior Acrylic paint over one coat of approved cement primer 0.000 Sqm Excess(+) Full Conversion INR

120.02 Two coats approved Gold paint band on False ceiling as per approved design and drawing. 0.000 Sqm Excess(+) Full Conversion INR

120.03 Two coats of approved Gold paint highlight on False ceiling/wall etc as per approved design and drawings. 0.000 Sqm Excess(+) Full Conversion INR

121 Providing and fixing gold polished brass handles of M/s chitra Enterprises or Equivalent with necessary brass screws including labour and all material etc. complete all as per drawings, specfication and as directed by EIC. The rate shall be inclusive of removing of existing handles if any.

121.01 200 mm long 0.000 each Excess(+) Full Conversion INR

121.02 300 mm long 0.000 each Excess(+) Full Conversion INR

121.03 450 mm long 0.000 each Excess(+) Full Conversion INR

121.04 150 mm long 0.000 each Excess(+) Full Conversion INR

121.05 Upto 100 mm long 0.000 each Excess(+) Full Conversion INR

122 Removing, repairing, refixing exisiting door shutters (of approx dimentions 2.2 m x 1.2m ) in original condition after completion of veneer/laminate fixing work including SS screw, adhesive ,wooden packing, all labours, carpenters required for fixing of all the fittings and fixtures,including repairing work of door shutters/frames if any etc. complete all as per specification, drawings and as directed by EIC. (Note : Veneer/laminate work shall be paid under relevant item) 0.000 Each Excess(+) Full Conversion INR

123 Providing & applying synthetic enamel paint in two or more coats on old / new wooden / steel surface, at all floors, levels & location using ready mixed & ready made synthetic enamel paint of approved make, shade and pattern including one coat of approved wood / steel primer including labour, material, scaffolding, surface preparation, cleaning etc complete all as per specifications and as directed by Engineer-in-Charge. (Note:- Synthetic enamel paint shall have VOC content less than 50 grams/ litre).

123.01 On wooden surfaces including one coat of wood primer 0.000 Sqm Excess(+) Full Conversion INR

123.02 On Steel surfaces including one coat of steel primer (red oxide based) 0.000 Sqm Excess(+) Full Conversion INR

124 Providing, applying and finishing with french spirit polish over old / new, wooden surface, at all floors, levels & location using two or more coats of french spirit polish over a coat of wood filler to form uniform neat finish, of approved make, shade and pattern including labour, material, scaffolding, surface preparation using sand paper & wood filler, cleaning etc complete all as per specifications and as directed by Engineer-in-Charge. 0.000 Sqm Excess(+) Full Conversion INR

125 Providing, applying and finishing with melamine polishing over new/old wooden surface, at all floors, levels & location using two or more coats for matt/ glossy / High glossy finish to form uniform neat surface of approved colour & texture, using approved make material including labour, material, scaffolding, surface preparation, cleaning etc complete all as per specifications and as directed by Engineer-in-Charge. Polishing process in the sequence as detailed below: 1) The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2) Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3) On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 0.000 Sqm Excess(+) Full Conversion INR

125.001 4) On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

126 Providing, applying and finishing with PU polishing and coating over old / new, wooden surface, at all floors, levels & location using two or more coats of PU polishing and coating over a coat of PU filler and sealer to form uniform neat finish, of approved make, shade and pattern including labour, material, scaffolding, surface preparation using sand paper & wood filler, cleaning etc complete all as per specifications and as directed by Engineer-in-Charge. 0.000 Sqm Excess(+) Full Conversion INR

127 Providing and fixing approved quality 6 mm thick glass mirror make of M/s. Saint Gobain "Classic" back lit mirror of various sizes with 8 mm thick marine ply back including painting the ply wood with two coats of synthetic enamel paint over coat of primer and carved burma teak wood moulded frame work of size of 125mm x 20mm alround , polishing the frame with 3 coat of french polish after preparation and making the surface very smooth and final mealamine spray finish, including providing & fixing rawal plug in wall / RCC, drilling screw holes, wooden packing if necessary etc., complete all as ditected by EIC.

127.01 6mm Mirror of size 750 x 1200 mm with Carved wooden frame of 125 mm x 30 mm. 0.000 Each Excess(+) Full Conversion INR

127.02 6mm Mirror of size 900 mm x 600 mm mm with Carved wooden frame of 125 mm x 30 mm. 0.000 Each Excess(+) Full Conversion INR

127.03 6mm Mirror of size 900 mm x 1800 mm mm with Carved wooden frame of 125 mm x 30 mm. 0.000 Each Excess(+) Full Conversion INR

128 Fabrication, supply and installation of dining table in marine plywood, laminated, synthetic marble top, 1st BTC wood undercarriage, PU polished including all materials, adhesives, SS screw, labour, scaffolding, wastages etc all as per approved drawing and as directed by EIC. Providing,Making and placing decorative dining table of size: 1.2 X 0.76 m. (approx) Or as per approved drawing consisting of followings: i)Table top made out of 18mm thick BWP grade marine plywood laminated one side 0.8 mm thick and top with artificial granite/synthetic marble of 18 mm thick of approved quality with 36 mm thick moulded edges. ii)The wooden frame work made out of various sections of Burma teak wood as shown as directed by Engineer-in-charge to effectively supported the table top Vertical facia of wood to be carved as per design similar to as shown in picture matching with the existing design as directed. iii)The table to have approx 4 main supports made out of single piece sections of Burma teak and duly carved and design as per the drawing. iv)The table wooden frame work to be polished 2 coats of PU polish as per specification. v)The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

129 Fabrication, supply and installation of dinning chairs in 1st BTC wood, PU polish, high density foam,premium quality fabric including all materials, labour, scaffolding, wastage, stiching etc. all as per approved drawing and as directed by EIC Providing, Making decorative wooden chairs (without hand rest) of over all approx size 450 X 450 mm as per the approved design consisting of followings i)The chairs to consist Decorative wooden legs with design and carvings as approved made out of single piece section of Burma teak wood. ii)Seating frames with designs, curve and carved back rest as shown and base wooden ties if required as instructed by Engineer-in-charge. iii) Upholestry for seating, back rest consisting of 40 PU foam rubber duly covered with high range fabric of approved design . iv) All wooden members are to be PU polished to get desired finish as directed by Engineer-in-charge and as per specification. v) Wood to be used for work should be Burma teak wood. vi) The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

130 Fabrication, supply and installation of Study/Writing chairs in 1st BTC wood, PU polish, high density foam,premium quality fabric including all materials, labour, scaffolding, wastage, stiching etc. all as per approved drawing and as directed by EIC Providing, Making decorative wooden chairs (with hand rest) of over all approx size 600 X 550 mm as per the approved design consisting of followings i)The chairs to consist Decorative wooden legs with design and carvings as approved made out of single piece section of Burma teak wood. ii)Seating frames with designs, curve and carved back rest as shown and base wooden ties if required as instructed by Engineer-in-charge. iii) Upholestry for seating, back rest and armed consisting of 40 PU foam rubber duly covered with high range fabric of approved design . iv) All wooden members are to be PU polished to get desired finish as directed by Engineer-in-charge and as per specification. v) Wood to be used for work should be Burma teak wood. vi) The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

131 Fabrication, supply and installation of Study/Writing table in marine plywood, laminated, synthetic marble top, 1st BTC wood undercarriage, PU polished including all materials, adhesives, SS screw, labour, scaffolding, wastages etc all as per approved drawing and as directed by EIC. Providing,Making and placing decorative dining table of size: 1.14 X 0.5 m. (approx) Or as per approved drawing consisting of followings: i)Table top made out of 18mm thick BWP grade marine plywood laminated one side 0.8 mm thick and top with artificial granite/synthetic marble of 18 mm thick of approved quality with 36 mm thick moulded edges. ii)The wooden frame work made out of various sections of Burma teak wood as shown as directed by Engineer-in-charge to effectively supported the table top Vertical facia of wood to be carved as per design similar to as shown in picture matching with the existing design as directed. iii)The table to have approx 4 main supports made out of single piece sections of Burma teak and duly carved and design as per the drawing. iv)The table wooden frame work to be polished 2 coats of PU polish as per specification. v)The frame to fitted with PVC buffers. vi) Providing and fixing matching drawer (approx size 0.5 X 0.3 m) made using marine ply with telescopic channels and brass handles (100mm) and finishing inside with 1.0 mm thick lamination. 0.000 Each Excess(+) Full Conversion INR

132 Fabrication, supply and installation of Study/Writing table in marine plywood, laminated, synthetic marble top, 1st BTC wood undercarriage, PU polished including all materials, adhesives, SS screw, labour, scaffolding, wastages etc all as per approved drawing and as directed by EIC. Providing,Making and placing decorative Study/Writing table of size: 1.2 X 0.5 m. (approx) Or as per approved drawing consisting of followings: i)Table top made out of 18mm thick BWP grade marine plywood laminated one side 0.8 mm thick and top with artificial granite/synthetic marble of 18 mm thick of approved quality with 36 mm thick moulded edges. ii)The wooden frame work made out of various sections of Burma teak wood as shown as directed by Engineer-in-charge to effectively supported the table top Vertical facia of wood to be carved as per design similar to as shown in picture matching with the existing design as directed. iii)The table to have approx 4 main supports made out of single piece sections of Burma teak and duly carved and design as per the drawing. iv)The table wooden frame work to be polished 2 coats of PU polish as per specification. v)The frame to fitted with PVC buffers. vi) Providing and fixing matching drawer (approx size 0.5 X 0.3 m) made using marine ply with telescopic channels and brass handles (100mm) and finishing inside with 1.0 mm thick lamination. 0.000 Each Excess(+) Full Conversion INR

133 Fabrication, supply and installation of chairs (for cofee table) in 1st BTC wood, PU polish, high density foam,premium quality fabric including all materials, labour, scaffolding, wastage, stiching etc. all as per approved drawing and as directed by EIC Providing, Making decorative wooden chairs (with hand rest) of over all approx size 600 X 550 mm as per the approved design consisting of followings i)The chairs to consist Decorative wooden legs with design and carvings as approved made out of single piece section of Burma teak wood. ii)Seating frames with designs, curve and carved back rest as shown and base wooden ties if required as instructed by Engineer-in-charge. iii) Upholestry for seating, back rest consisting of 40 PU foam rubber duly covered with high range fabric of approved design . iv) All wooden members are to be PU polished to get desired finish as directed by Engineer-in-charge and as per specification. v) Wood to be used for work should be Burma teak wood. vi) The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

134 Fabrication, supply and installation of Cofee Table / Side table in marine plywood, laminated, synthetic marble top, 1st BTC wood undercarriage, PU polished including all materials, adhesives, SS screw, labour, scaffolding, wastages etc all as per approved drawing and as directed by EIC. Providing,Making and placing decorative Cofee Table / Side table of size: 0.6m Dia. (approx) Or as per approved drawing consisting of followings: i)Table top made out of 18mm thick BWP grade marine plywood laminated one side 0.8 mm thick and top with artificial granite/synthetic marble of 18 mm thick of approved quality with 36 mm thick moulded edges. ii)The wooden frame work made out of various sections of Burma teak wood as shown as directed by Engineer-in-charge to effectively supported the table top Vertical facia of wood to be carved as per design similar to as shown in picture matching with the existing design as directed. iii)The table to have approx 4 main supports made out of single piece sections of Burma teak and duly carved and design as per the drawing. iv)The table wooden frame work to be polished 2 coats of PU polish as per specification. v)The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

135 Fabrication, supply and installation of Centre table in marine plywood, laminated, synthetic marble top, 1st BTC wood undercarriage, PU polished including all materials, adhesives, SS screw, labour, scaffolding, wastages etc all as per approved drawing and as directed by EIC. Providing,Making and placing decorative Centre table of size: 0.75 X 0.75 m. (approx) Or as per approved drawing consisting of followings: i)Table top made out of 18mm thick BWP grade marine plywood laminated one side 0.8 mm thick and top with artificial granite/synthetic marble of 18 mm thick of approved quality with 36 mm thick moulded edges. ii)The wooden frame work made out of various sections of Burma teak wood as shown as directed by Engineer-in-charge to effectively supported the table top Vertical facia of wood to be carved as per design similar to as shown in picture matching with the existing design as directed. iii)The table to have approx 4 main supports made out of single piece sections of Burma teak and duly carved and design as per the drawing. iv)The table wooden frame work to be polished 2 coats of PU polish as per specification. v)The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

136 Providing and laying first quality matt finished / anti skid ceramic tile in flooring and water repellant ceramic tile in dado/cladding of 6 mm minimum thickness or as per specification of approved manufacturer and conforming to IS:15622 and approved colour, shade, design, pattern in cement mortar bedding/ backing, close jointed and grouted with matching cement slurry to match the colour of the tiles, finished tolevel, line, slope and plumb including cutting of tiles, making openings /cutout if necessary, wastage and final cleaning of surfaces as required, curing, and including carefully removing existing flooring/dado/skirting with mortar and disposal of debries outside campus etc. complete all as per drawings, specifications & as directed by Engineer in Charge. (In rooms)

136.01 In Flooring with 300 mm X 300 mm or approved size anti skid ceramic tile laid over and including 20mm thick cement mortar bedding1:4 (1 cement : 4 coarse sand) using reday mix mortar. 0.000 Sqm Excess(+) Full Conversion INR

136.02 In dado/ cladding of size 300 x 600mm/300 x 450mm or approved size with approved design/pattern water repellant ceramic tile laid over and including 12 mm thick cement mortar backing of (1:4) using ready mix mortar, PVC corner beading/ nosing of approved quality and colour at the corner and edges of the tiles including finishing and embedding in the wall etc. complete all as directed by the Engineer- in-charge. 0.000 Sqm Excess(+) Full Conversion INR

137 Providing and fixing in position at all floors, levels / heights 18 mm thick mirror polished natural stones slab for door frame in two overlapping layers one piece full length / height of approved shade, finished sizes as directed including machine cut / hand cut, final cleaning, moulding and polishing of exposed edges, in line, level, plumb and fixing the stone with Cement Mortar 1:4 (Using factory made Ready Mix Mortar only), 20mm backing & overlapping of 20mm shall be fixed with Araldite adhesive, with best workmanship, finishing, curing, and including carefully removing existing door frame and disposal of unserviceable material outside campus etc. complete all as per specifications, drawings & as directed by the EIC. Note : Exposed surface on Elevation & exposed vertical finished face shall be measured for payment in sqm. Overlapping & edges etc shall not be measured.

137.01 Jet Black Granite Stone 0.000 Sqm Excess(+) Full Conversion INR

138 Filling in bath, W/C, toilet, depressed areas with water proofing brick bat coba of the agency approved by the department at all floors, levels and locations upto the required level and making the surface finished suitable to receive floor finish, including finishing, curing, compaction etc all complete as per drawings and water proofing agency's specifications & as directed by the Engineer-in charge. ( Note:- The generally brick bat coba consist of broken brick bats of size 25 mm to 115 mm with 50% of Cement Mortar (1:4) using Ready mix Cement mortar admixed with approved water proofing compound conforming to IS:2645 as per manufacturer's specifications) 0.000 Cum Excess(+) Full Conversion INR

139 Providing & Applying seamless Acrylic based chemical waterproofing system with minimum 1 mm DFT (dry film thickness excluding thickness of membrance) including surface preparation, primer coat, reinforcing membrane (minimum 45 GSM) and multiple layers of chemical coat (2 to 3 coats as per manufacturer's specification with minimum consumption @ (1.6 +/- 5 % kg per sqm for horizontal surface), cleaning, all complete as per the manufacturers specifications and as directed by Engineer-In-Charge.

139.01 Over Horizontal surface, with reinforcing membrance 0.000 Sqm Excess(+) Full Conversion INR

140 Supplying & fixing in position at all floors and location 25mm thick PVC integral free foam sheet in the form of flush finished door shutter manufactured by M/s. Jain Irrigation Systems Ltd. ( Ex-cel sheet), M/s. Rajshri plastiwood or approved equivalent of white/approved colour solid section, extruded rigid, light weight sheet with fine and homogeneous closed cell structure with smooth, glossy, hard surface finish on both sides including providing recess for hinges, providing & fixing 3 nos 100 mm heavy duty Gold color S.S. hinges and 2 nos. of 100 mm Gold color SS Bow handles with back plate and 1 no. gold colour finish keyless cylindrical lock and including fixing shutters in position to stone / wooden frames (Stone Frame shall be paid separately under relevant item and wooden frames are existing in position) at all floors by cutting / planing required if any, fixing with wooden packing pieces if required, including finishing all edges smooth with mixture of PVC powder & solvent including wastages, labours tools etc all as per specifications, drawings & as directed by the Engineer in charge.

140.01 For toilets of room and suite having 1.0 mm thick decorative laminate of approved colour, shade, texture and make on both faces/side of shutter fixed using Araladite or approved suitable adhesive and P&F 2 mm thick PBC edge beading. 0.000 Sqm Excess(+) Full Conversion INR

140.02 Forshaft door of toilet having 1.0 mm thick decorative laminate of approved colour, shade, texture and make on single face/side of shutter fixed using Araladite or approved suitable adhesive and P&F 2 mm thick PBC edge beading. 0.000 Sqm Excess(+) Full Conversion INR

141 Providing coving and POP cornice and moulding work at all location, floors and levels as per drawing, specification and as directed by EIC

141.01 Coving work as per approved design and details for cove light 0.000 RM Excess(+) Full Conversion INR

141.02 Cornice work in POP as per approved design and drawing 0.000 RM Excess(+) Full Conversion INR

141.03 POP moulding work of various dia of approved design and drawing. 0.000 Nos. Excess(+) Full Conversion INR

142 Providing and fixing 18 mm thick Bison Board at all floors and levels including providing and fixing as shown in the drawing including cost of all materials, adhesives, labours,scaffolding, wastages, fixing of fitting and fixtures, painting surface with two coat of Synthetic Enamel paint of approved shade over a coat of primer etc. all complete as per specification, drawing and as directed by Engineer-in-Charge. Note :The rates shall includes removal and disposal of old ventilator if any. 0.000 Sqm Excess(+) Full Conversion INR

143 Providing and fixing DAE LOGO of 600mm dia on gold color etched sheet with black/blue embosing including required scaffolding,transportation, labours, etc. complete all as per drawings and specification and directed by the Engineer-In-Charge. 0.000 Nos Excess(+) Full Conversion INR

144 Providing & fixing wall paneling at all floors, levels & location consisting of 12mm thick water proof marine ply wood confirming to IS 710 & with 3mm thick teak wood veneer fixed on 19 x 38 mm (finished size) size kiln seasoned, chemically treated for protecting the wood against termites, pests approved salwood @ 600 mm centre to centre both ways fixed on walls, including providing & fixing teak wood beading (60 mm X 50 mm / 60 mm X 40 mm approx size) at top as per drawing for full length using SS screws including suitable SS screws of required size and providing 3 mm / 4 mm wide grooves between veneer panels of different shades (dark & light colour) including applying 3 coats of melamine polish after preparing the surfaces, scaffolding, tools, screws, rawl plug etc. complete all as per drawing, specifications and as directed by the Engineer-in-Charge. 0.000 Sqm Excess(+) Full Conversion INR

145 Providing 15mm X 6mm wide Solid Brass bar having approved finish and fixing over existing wooden table and including all labour, Cutting, Wastage, Sizing and including making necessary notch for fixing etc. all complete as per specification, drawing and as directed by Engineer-In-Charge. 0.000 RM Excess(+) Full Conversion INR

146 Providing and fixing carpet/rug having 75% wool & 25% silk and min thickness 10 to 15 mm, as per approved design, pattern, size and shape including material, labour, wastage, transportation and taxes. etc. complete all as directed by Engineer In charge. 0.000 Sqm Excess(+) Full Conversion INR

147 Supplying and fixing at all location, levels and floors in position high resolution canvas printing paintings including composing / replication of approved art and including providing and fixing 6mm thick marine ply (IS 710) photo frame backing with teak wood periphery framing & intermediate supports including cutting to required sizes, jointing, adhesive, melamine polished, wastage, transportation, material, labour etc. complete all as per drawing, specification and as directed by EIC.

147.01 High resolution canvas printing paintings including composing / replication of approved art 0.000 Sqm Excess(+) Full Conversion INR

147.02 6mm thick marine ply (IS 710) including melamine polishing 0.000 Sqm Excess(+) Full Conversion INR

147.03 Decorative teak wood photo frame with carving including PU polish (Size 50mm X 100mm) 0.000 RM Excess(+) Full Conversion INR

147.04 Decorative teak wood photo frame including PU polish (Size 38mm X 19mm) 0.000 RM Excess(+) Full Conversion INR

148 Providing & fixing at all locations, levels & floors RFID operated flush door lock (Right/Left Inside Opening) suitable for door thickness of 30 to 50 mm and having CE(EN 14846) certification of approved make and brand (M/s. Godrej OMEGA or approved equivalent) and including back-set, four nos. of AA Alkaline batteries of 1.5 V (ISI Marked), brushed stainless steel finish, Operates on RFID (MIFARE technology) with frequency of 13.56MHz giving seamless working, compatibale with other cards (such as Staff cards, housekeeping cards, guest cards, emergency cards), Detailed audit records of up to 414 events can be stored in the lock's memory, low battery indication for Preventive maintenance, Unlocking through the card from the outside is restricted once the lock’s privacy bolt function is switched on from the inside thus giving ultimate privacy to the occupant, the lock shall be opened with the mechanical key (In case of emergency), including all cutting, chasing, fixing in existing doors, labour, material etc complete all as per specifications and as directed by EIC. 0.000 Each Excess(+) Full Conversion INR

149 Providing & laying at all floors & locations Homogeneous Full body Vitrified tile/ Glazed vitrified tile/ double charge/ multi charge (Glossy/Matt/Satin)/ approved manufacturers of sizes 2400mm X 1200mm or as per approved size and having mimimum thickness 8.5 mm or as specified by approved manufacturer tiles conforming to IS:15622 having water absorption less than or equal to 0.08% (Group B I a), in flooring/skirting/ dado/ cladding at all floors and location, heights/ levels and lead in approved pattern and colour, shade laid over ready mix cement mortar bedding/ backing/ adhesive backing, including cleaning and preparing the surface for bedding/backing, spreading the neat cement slurry, close jointed and grouted with matching coloured readymade cement grout and approved pigment as per manufacturer's specifications, finished to level, line, slope and plumb, cutting of tiles, wastage, making openings/ cut out if neccesary, final cleaning of surfaces,curing and including removing existing wooden flooring with disposal to directed place etc. all as per drawings, specifications & as directed by Engineer in charge. Note:- The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

149.01 In flooring using Homogeneous Full body vitrified tile of size 2400mm X 1200 mm laid over and including 20 mm thick cement mortar1:4 bedding (using reday mix mortar) and spreading neat cement slurry by using minimum cement about 2 kg/sqm prior to bedding and spreading cement paste using minimum cement of about 4.50 kg/sqm over bedding, 0.000 Sqm Excess(+) Full Conversion INR

149.02 In Skirting using Homogeneous Full body vitrified tile of size 2400mm X 1200 mm laid over and including 12 mm thick cement mortar1:4 backing (using reday mix mortar) 0.000 Sqm Excess(+) Full Conversion INR

150 Providing and fixing in position on wall best quality, top class finishing, 500mm high National Emblem of India (Ashok Stambh with Satyamev Jayate in hindi) in Brass (approx minimum weight of 3.80kg) all as per approved, drawing including all labour material etc comlplete as per specification as directed by EIC 0.000 Each Excess(+) Full Conversion INR

151 Providing & fixing in position at all levels & location venetian Roller blinds of approved make, having superior quality powder coated channel along with heavy duty component parts for smooth funtioning of blinds, blinds made up of 100 wide rayon polyester fabric of approved shade & colour etc complete all as per specifications and as directed by Engineer in Charge. 0.000 Sqm Excess(+) Full Conversion INR

152 Providing & fixing in position at all levels & location 30mm thick HDHMR board jali carved using CNC machine made by using 800mm X 1200mm HDHMR board of approved make, color, shade, texture, the design of jali shall be as per drawing and approval of Architect, and including two coats of Duco finish for acoustic purposes, fittings and fixtures etc complete all as per drawing, specifications and as directed by Engineer in Charge. 0.000 Sqm Excess(+) Full Conversion INR

153 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer of approved make conforming to IS: 3564 with ISI mark including necessary accessories and screws etc for fixing with alumnium/ wooden/ steel doors with necessary bolts & nuts, labour, scaffolding etc complete all as per specifications and as directed by the Engineer-in-charge. 0.000 Each Excess(+) Full Conversion INR

154 Supplying and fixing in position at all floors and location door frame and shutter assembly having door frame made of using Burma Teak wood and shutter made using 40 mm thick double leaf flush door shutter (IS:2202) of approximate size 2mx1.65m with 3mm veneer facing (of approved make) on both sides, with vision panel as per design, with teak wood moundings all around shutter, with carved teak wood decorative design on both sides of shutter as per the approved design and drawing, fixing with butt hinges of required size with necessary screws and including providing & fixing gold colour finish decorative Brass handles (300 mm long, 4 Nos.), 125 mm long brass hinges 8 nos., decorative brass aldrop 2 Nos. (300 mm long having 16 mm dia rod) with extra staple, 2nos. brass 100 mm long door stopper with rubber bushing, 2nos. concealed door closer, 2nos. decorative brass tower bolt (300mm long), 6 mm thick visin panel and finishing the all surface with PU polishing, BTC teak wood (Lipping, moulding, Architrave etc) and including all labour, material, wastage and other required fittings & fixtures etc. all complete as per specifications, approved drawings and as directed by the Engineer-in-charge. 0.000 Each Excess(+) Full Conversion INR

155 Supplying & fixing in position the following type solid core block board flush door shutter (Single/ double leaf) with commercial ply facing / prelamination on both sides conforming to IS 2202 (Part-1) of approved make & brand with external / internal type best and premium quality Burma Teak Wood (BTC) lipping alround of required width and depth (20 minimum thickness all around) of shutter as per IS/as specified, fixing shutters in position to wooden frames works (door frames shall be paid separately under relevant item) at all floors by cutting/ planing if necessary including labour for fixing of the fittings & fixtures as per drawing with wooden packing pieces if necessary (but excluding the cost of fittings and fixtures with SS screws which shall be paid separately under relevant item), including view panel wherever required as per drawing, finishing as specified all as per specifications, drawings and as directed by Engineer In Charge.

155.01 38 mm thick, with both faces having 3 mm thick teak wood veneer finished with PU Polish. 0.000 Sqm Excess(+) Full Conversion INR

156 Providing and fixing in position 2 mm thick brass name plate having size (200mm X300mm) with embosed matter and colour fill as directed/drawing, including necessary brass screws etc complete all as per specification and as directed by EIC. 0.000 Each Excess(+) Full Conversion INR

157 Providing & fixing Hollow Metal Pressed steel (HMPS) door frames of following profile fabricated out of 1.60 mm thick G.I sheet of coating (Class VIII of zinc coating) 120 gram/sqm, manufactured by Sail / Lloyds/ Jindal or equivalent of profiles / size generally conforming to IS 4351-2003 with suitable one/two set rebates for fixing shutters and also rebate suitable for fixing fixed glazing including hole for self tapping screws wherever shown in the drawing, each frame to contain hinge jamb, lock jamb and head all rigidly fixed together with welded /mechanical joints with back plates /angles to correct shape & angles including providing and fixing base ties with GI channel 50x25mm, 1.25mm thick suitable section to suit floor thickness / angle thresholds with MS angle 25x25x3mm, 6nos. of adjustable lugs per frame, providing and welding of 40x40x5mm,150mm long angle cleats for hinges with necessary tapped holes for fixing counter sunk headed machine screws to suit heavy duty oxidised / stainless steel hinges of size 125mm x 65mm x 2.8mm/125mm x 76mm x 2.80mm/ 100mm x59mm x2.6mm/75mm x 48mm x 2.45mm or shop type welding and self taping screw for fixing hinges/ piano hinges etc. and finishing the same to smooth etc. (but excluding the cost of hinges which shall be paid under the relevant item) including providing each door frame with necessary lock strike plates, mortar guards, buffers, bushes etc. required for tower bolt/ baby latches, tadis, safety chains, aldrops etc including fixing the frame to brickwork/ concrete work with necessary PCCor bolted/ screwed to concrete work, painting a shop coat of polyurethane paint including etching the surface with ETCH primer etc. including painting the exposed surfaces with two coats of synthetic enamel paint of approved make and colour over a coat of red oxide/ zinc chromate primer and painting the unexposed surfaces with two coats of anticorrosive bituminous paint, after rectifying the damaged PU primer due to transport including filling the hollows of door frame with C.C.1:2:4 using 12 mm size downgraded stone aggregate, curing, finishing etc. all complete as per drawings, specifications and as directed by Engineer in charge. Note: The quoted rate shall include cost of base tie / angle and all accessoriesmentioned in the item description except iron mongeries (i.e. fittings and fixtures with wood and machine/ self taped screwsas required, which shall be measured and paid separately under relevant item.)

157.01 Profile 145mm x 60 mm with single rebate for doors. 0.000 RM Excess(+) Full Conversion INR

158 Providing and laying autoclaved aerated cement (AAC) blocks masonry with 110mm to 300mm thick AAC blocks as per approved manufacturer, using approved block laying polymer modified adhesive mortar in super structure above plinth level at all locations, levels & lead with RCC band at sill level and lintel level, curing, scaffolding etc complete all as per specifications and as directed by Engineer in-Charge. (The RCC band shall have 2 nos. of 8 mm dia reinforcement and concrete of minimum grade (1:1.5:3). ( AAC blocks shall be conforming to IS:2185, Part-3, having Grade-I with block of density 551 to 650 Kg/cum) . The payment of RCC band and reinforcement shall not be made seperately, the quoted rate shall be inclusive of all. 0.000 Cum Excess(+) Full Conversion INR

159 Fabrication , supply and installation of dining table in marine plywood, laminated, synthetic marble top,1st BTC wood undercarriage, PU polished including all materials, adhesives, SS screw, labour, scaffolding, wastages etc all as per approved drawing and as directed by EIC. Providing,Making and placing decorative dining table of size: 2.4 m x 0.9 m (approx) Or as per approved drawing consisting of followings: i)Table top made out of 18mm thick BWP grade marine plywood laminated one side 0.8 mm thick and top with artificial granite/synthetic marble of 18 mm thick of approved quality with 36 mm thick moulded edges. ii)The wooden frame work made out of various sections of Burma teak wood as shown as directed by Engineer-in-charge to effectively supported the table top Vertical facia of wood to be carved as per design similar to as shown in picture matching with the existing design as directed. iii)The table to have approx 8 main supports made out of single piece sections of Burma teak and duly carved and design as per the drawing. iv)The table wooden frame work to be polished 2 coats of PU polish as per specification. v)The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

160 Fabrication, supply and installation of dinning chairs in 1st BTC wood, PU polish, high density foam,premium quality fabric including all materials, labour, scaffolding, wastage, stiching etc. all as per approved drawing and as directed by EIC Providing, Making decorative wooden chairs (with hand rest) of over all approx size 450 X 450 mm as per the approved design consisting of followings i)The chairs to consist Decorative wooden legs with design and carvings as approved made out of single piece section of Burma teak wood. ii)Seating frames with designs, curve and carved back rest as shown and base wooden ties if required as instructed by Engineer-in-charge. iii) Upholestry for seating, back rest consisting of 40 PU foam rubber duly covered with high range fabric of approved design . iv) All wooden members are to be PU polished to get desired finish as directed by Engineer-in-charge and as per specification. v) Wood to be used for work should be Burma teak wood. vi) The frame to fitted with PVC buffers. 0.000 Each Excess(+) Full Conversion INR

161 Providing and fixing PVC sports flooring system having minimum 7.0 mm thickness (similar to active pro sports flooring of M/s. Responsive or other approved equivalent), the PVC roll having approx width (1.8 / 1.5 m) of approved colour, pattern & shade and manufactured by approved manufacturer, the PVC flooring should have properties of shock absorption, ball rebound, slip resistant, fire retardant and anti-bacterial and including supplying, applying suitable manufacturer recommended adhesive having low VOC, the minimum thickness of anti slip layer shall be 2 mm and including all labour, material, wastage etc. complete all as per specification & as directed by the EIC. (Suitable for Gym) 0.000 Sqm Excess(+) Full Conversion INR

162 Supplying and fixing in position at all floors and levels the follwing gym equipments of M/s. Powermax or other approved equivalent including all necessary fitting fixtures for making equipments ready to use etc complete all as per manufactureres specification and as directed by EIC

162.01 TDA-360® 10.1inch HD Display Motorized Treadmill with Auto Incline, Product ID.: 8904335102458 0.000 Each Excess(+) Full Conversion INR

162.02 BU-650 Magnetic Upright Bike with LCD Display, Product ID.: 8904335102533 0.000 Each Excess(+) Full Conversion INR

162.03 EH-350S Elliptical Cross Trainer, Product ID.: 8904335103301 0.000 Each Excess(+) Full Conversion INR

162.04 BM-100A Multi-functional Bench Press, Product ID.: 8904335104094 0.000 Each Excess(+) Full Conversion INR

162.05 BDS-1000 Adjustable Combination Dumbbells Bench with Storage, Product ID.: 8904335104575 0.000 Each Excess(+) Full Conversion INR

162.06 PDKS-20P Adjustable PVC Cement Kettlebell Dumbbells Set., Product ID.: 8904335103325 0.000 Each Excess(+) Full Conversion INR

163 Cleaning of existing structural glazing using mild detergent, soap solution using soft foam without damaging and scratching, including water jet spray, blower, scaffolding, labour, material etc complete all as per specification and as directed by EIC. 0.000 Sqm Excess(+) Full Conversion INR

164 Providing and laying first quality matt finished / anti skid / polished vetriifed tile in flooring and water repellant vetrified tile in dado/cladding of 8 mm minimum thickness or as per specification of approved manufacturer and conforming to IS:15622 and approved colour, shade, design, pattern in cement mortar bedding/ backing, close jointed and grouted with matching cement slurry to match the colour of the tiles, finished tolevel, line, slope and plumb including cutting of tiles, making openings /cutout if necessary, wastage and final cleaning of surfaces as required, curing, and including carefully removing existing flooring/dado/skirting with mortar and disposal of debries outside campus etc. complete all as per drawings, specifications & as directed by Engineer in Charge. (In Suites)

164.01 In Flooring with 600 mm X 600 mm or approved size anti skid mat finished vetrified tile laid over and including 20mm thick cement mortar bedding1:4 (1 cement : 4 coarse sand) using reday mix mortar. 0.000 Sqm Excess(+) Full Conversion INR

164.02 In dado/ cladding of size 1200 x 600mm or approved size polished vetrified tiles with approved design/pattern water repellant vetriifed tile laid over and including 12 mm thick cement mortar backing of (1:4) using ready mix mortar, PVC corner beading/ nosing of approved quality and colour at the corner and edges of the tiles including finishing and embedding in the wall etc. complete all as directed by the Engineer- in-charge. 0.000 Sqm Excess(+) Full Conversion INR

165 Providing and fixing in position at all floors, levels and location minimum 6 mm thick hravy quality 100% Polypropylene synthetic carpet, fire retardent, plain backing, needle punch technology, stain proof, having colour, shade, make, texture as per approval for corridor flooring and skirting including material, labour, wastage, transportation and taxes. etc. complete all as directed by Engineer In charge. 0.000 Sqm Excess(+) Full Conversion INR

166 Providing and laying rubble stone hard core soling of following consolidated thickness in sub base to floor and in plinth protection to required levels and lines with first quality rubble, hand set, well packed including filling the interstices with smaller stone chips of approved quality, supplying & finishing/ blinding the surfaces with approved blinding quality murrum/ stone dust including watering, consolidation etc. complete as per specification drawings & as directed by Engineer in charge. Note: Quoted rates shall include the cost of filling materials of smaller stone chips and murrum/ stone dust etc. (150 mm consolidated thickness) 0.000 Sqm Excess(+) Full Conversion INR

167 Providing and fixing 80 mm thick (min.) factory made interlocking paver blocks of specified finish, approved make and colour, shade, size, shape laid in pattern manufactured with cement concrete grade not less than M-40 and conforming to IS:15658, including supplying & laying 50 mm thick stone dust evenly spread over the sub-base including consolidation of sub-base properly vibrating with the surface vibrator, finishing to line, level and slope, finally filling the joints with fine clean sand and cleaning the surface disposing off the debris at directed place etc. complete all as per specification and as directed by the Engineer- in- Charge. (Using reflective (Smooth finish) interlocking paver blocks/shot blasted interlocking paver blocks) 0.000 Sqm Excess(+) Full Conversion INR

168 Providing and placing in postion at all floors, levels and location Single bed with overall size 3' X 6.5' and with matching mattress. The main and sub frame of bed shall be made of second class teak wood and other parts (head, leg and sides) shall be made of 19mm thick (IS-710) marine ply. The bed top shall be made of 19mm thick (IS-710) marine ply with 1.0 mm thick laminate (of approved make, colour, texture and shade) on top face only with teakwood beading on the edges. The bed shall have head rest of height 4'. The head side and leg side shall be made of using 19mm thick (IS-710) marine ply with 3.0 mm thick wood venner on exposed faces only with matching melamanie polishing. The all exposed faces and sides of bed visible after laying of mattress shall be finished with 3.0 mm thick wood venner with matching melamanie polishing. Mattress shall be minimum 200mm thick, having Cover material quilted tapestry, PU foam, Bonded foam and high density rubberized Coir filling material, Thickness of Top Layer (±2 mm) 25 mm, Thickness of Bottom Layer (±2 mm) Rubberised Coir Foam Material of Core, Thickness of Quilting ( ±2 mm) 24 mm Fabric Composition Polyester Construction Woven Fabric Mass ( Minimum ) 300 gm/m2 , Core Layer 1 Density 90 Kg/m3 Top Layer Density 90 Kg/m3 , Bottom Layer Density Compression Set for PU Foam (non quilting) as per IS 7888 1976 (Max) 10% Durability Test for Complete Mattress loss of height not more than 13 mm (as per ASTM 1566), etc complete all as per approved drawing, specification and as directed by EIC. 0.000 Each Excess(+) Full Conversion INR

169 Providing and fixing Hindi & English letters for the name board / writing boards in 2.5 mm thick brass plate with engreaving of approved hindi / English latters / matters with mirror finish with lacquer coating of various sizes and shapes as per drawing/sketch, including material, labour, transportation, taxes and delivery at required places. Installation at all level etc. complete as directed by. Engineer In charge. 0.000 Sq. Inch Excess(+) Full Conversion INR

170 Removing existing furniture, door shutter, panelling, wood work, materesses, wall accessories etc. carefully from its location and stacking at directed place including rearraging after work and including disposal of unserviceable material ouside campus with all associated lead , lift , loading, unloading, trasnportation etc. complete all as per direction of EIC.

170.01 For Rooms 0.000 Job Excess(+) Full Conversion INR

170.02 For Suites 0.000 Job Excess(+) Full Conversion INR

170.03 From Conference room including removing existing glass doors including frame with fittings and fixtures 0.000 Job Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Select, Excess (+), Less (-) Less (-)

Tender Inviting Authority: Chairman GB

Name of Work: Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No: DCSEM/CQD/QSB/25-26/NIT/75 dt.19.02.2026

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

200 PART - II : PUBLIC HEALTH ENGINEERING WORKS

201 A : SANITARYWARES & CP APPURTENANCES

202 Providing and fixing in position following Vitreous China Wall Hung type Wash down pattern water Closet consisting following items of work:- i) Providing Vitreous China wall hung type wash down pattern Water Closet ( EWC ) conforming to IS 2556 (part XVI) with integral "P" trap outlet with water seal not less than 50 mm with vent and necessary C.I. brackets supports. ii) Providing thermosetting or thermoplastic Seat & cover conforming to IS 2548, fixing seat & cover for water closet as per manufacturer's specification including the cost of corrosion resistant hinges, bolts, nuts, non ferrous or S.S washer etc. all complete. iii) Fixing the Water closet in position, jointing the trap, water closet and CI/UPVC pipe by Epoxy grout or Rubber seal as per pipe manufacturer. iv) Cutting hole, making grove or chases in the wall, floors, slabs etc., reinstating to it's original condition after completion of work, painting all metallic parts with two coats of flat oil paint of approved make & shade over a coat of primer, finishing the gaps with white / matching colour cement etc. all complete. v) Testing the system to the full satisfaction of the Engineer-in-Charge.

202.01 Vitreous China European Water Closet of French Gold Colour with P trap of Cera Cat. No. S1044148FG Carlton Glitz French Gold with slow falling cover or approved equivalent make and including cost of removing the existing one & disposing off debris etc. complete all as per specification and as directed by the EIC. 0.000 Each Excess(+) Full Conversion INR

202.02 Vitreous China European Water Closet of white Colour with P trap of Cera No: S1043147 with slow falling cover or approved equivalent make and including cost of removing the existing one & disposing off debris etc. complete all as per specification and as directed by the EIC. 0.000 Each Excess(+) Full Conversion INR

203 Providing Flushing arrangement to water closet including providing and fixing manually operated PVC low level concealed flushing cistern consisting following items of work :- Providing 3.0 / 6.0 ltrs. capacity white colour PVC low level, leak proof, water saving, dual flush, durable concealed Flushing Cistern with all inside syphonic fittings && flush plate, duly assembled conforming to IS:7231 of following make, fixing the cistern in position using CP brass screws, rawl plugs, brackets etc. as per the manufacturer's recommendation, making outlet connection with EWC including the cost of supplying & fixing PVC Flush pipe etc. all complete. Cutting hole, making chases in the walls, floors, slabs etc and reinstating the surface to the original condition, painting all metallic parts with two coats of flat oil paint of approved make and shade over a coat of primer, finishing the gaps with white / matching cement etc. all complete. Testing the entire system to the full satisfaction of the E.I.C. and removing the existing one depositing to deptt. Stores etc. complete all as directed by the Engineer-in-Charge.

203.01 Providing and Fixing Flushing arrangement with Concealed cistern Set with Full Frame Cera Cat No. B1110111, Accessories included B1190104+B1190105+B1190106+ B1190107, Chevron Concealed cistern knob Cat No. B1120101FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

203.02 Providing and Fixing Flushing arrangement with Concealed cistern Set with Full Frame Cera Cat No. B1110111, Accessories included B1190104+B1190105+B1190106+ B1190107, Chevron Concealed cistern knob Cat No. B1120101 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

204 Providing and fixing first Quality Vitreous China hand wash Basin Consisting following items of work. - i) Providing Wash Basin and placing it in position as shown in the drawing or as per manufactures specification or as directed including finishing the joints with white / matching colour cement all complete. ii) Fixing various CP fittings such as Waste Coupling, Bottle Trap including fixing 32 mm minimum 10kg class PVC pipe conforming to IS:4985 (and fittings conforming to IS:7834). Placing and fixing Waste Pipe from Bottle trap to adaptor / Nahani trap / Floor Trap. iii) Fixing the Wash Basin in position, including providing M.S./C.I. Brackets & Screws for the basin. iv) Cutting hole, making grove or chases in the wall, floors, slabs etc., reinstating to it's original condition after completion of work, painting, finishing the gaps etc. all complete as directed by Engineer-in Charge. v) Fixing Vitreous China under / over the counter / semi recessed type Wash Basin of following model and make conforming to IS 2556 and placing it in position with the granite platform as shown in the drawing or as directed including finishing the joints with white cement all complete. vi) Testing the system to the full satisfaction of the Engineer in Charge

204.01 Vitreous China Wash Hand Basin of French Gold Thin rim, Size 550 x 380 x 110 mm of M/s Cera Cat No. S2020158FG or equivalent model. 0.000 Each Excess(+) Full Conversion INR

204.02 Vitreous China Wash Hand Basin of snow white colour, Size 550 x 380 x 110 mm of M/s Cera Cat No. S2020158 or equivalent model. 0.000 Each Excess(+) Full Conversion INR

205 Providing & fixing in position best quality bevelled edgeplate Glass Mirror with PVC frame of following size with 6 mm thick marine ply wood (confirming to IS:710), fixed with required numbers of CP brass cupscrews and caps, washers etc. including drilling holes, providing & fixing rawl plug in RCC/ brick wall, woodenpacking behind the mirror if necessary, reinstating the damages to its original condition etc. all complete as directed by EIC.

205.01 6 mm thick Plate glass Mirror of size 1000 mm x 600mm / of required size with 6 mm thick marine ply wood (confirming to IS:710:2010) backing & PVC moulded frame of approved shade or as directed by the E.I.C 0.000 Sq.m. Excess(+) Full Conversion INR

206 Providing & fixing in position following approved quality water saving CP fittings / Fixtures of 15 mm nominal dia. with ISI mark / approved make of following type including providing & fixing specials, wall flanges and fixing to concealed / exposed pipe line with leak proof threaded joints using tephlon tapes, testing the joints hydraulically to a pressure of 10 kg./ sq.cm, rectifying the leaky joints. if any, including cleaning etc. complete all as per specification.

206.01 2 way bib cock with wall flange of Cera 'Ruby' Cat No. F1005161FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.02 2 way bib cock with wall flange of Cera 'Ruby' Cat No. F1005161CH or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.03 Basin mixer with wall flange French Gold, Cera Cat No. : F1005452FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.04 Basin mixer with wall flange French Gold, Cera Cat No. : F1005452 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.05 Angular Stop Cock with wall flange of Cera 'Ruby' French Gold Cat.No.F1005201FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.06 Angular Stop Cock with wall flange of Cera 'Ruby' Chrome Cat.No.F1005201 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.07 C.P. Brass Concealed Stop cock with adjustable wall flange of Jaquar Cat. no. ALD-081 (25mm) with exposed part kit of Jaquar 'Florentine' Cat No.-FLR-5083NK complete or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.08 Single lever diverter concealed body of Cera Cat No. F4030101FG with exposed part kit of Cera Cat No. F1005721FG and spout with wall flange of Cera Cat No. F1005661FG or approved equivalent make. 0.000 Each Excess(+) Full Conversion INR

206.09 Single lever diverter concealed body of Cera Cat No. F4030101 with exposed part kit of Cera Cat No. F1005721CH and spout with wall flange of Cera Cat No. F1005661CH or approved equivalent make. 0.000 Each Excess(+) Full Conversion INR

Shower arm with wall flange of Cera Cat No. F7010112FG or approved equivalent make. 0.000 Each Excess(+) Full Conversion INR

206.11 Shower arm with wall flange of Cera Cat No. F7020111AB or approved equivalent make. 0.000 Each Excess(+) Full Conversion INR

206.12 Health Faucet of CERA, Cat. No. F8035101FG, complete with flexible hose and wall hook, (Minimum Hose length 1.2mtr/1.5mtr) including all necessary fittings, or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.13 Health Faucet of CERA, Cat. No. F8030112AB, complete with flexible hose and wall hook, (Minimum Hose length 1.2mtr/1.5mtr) including all necessary fittings, or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.14 C.P. brass Waste Coupling 32mm size of Cera Cat No. F8050102 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

206.15 C.P. brass Bottle Trap 32mm Size including Wall Connection Pipes & Wall Flange of Cera Cat.No. F8060101 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207 Providing and fixing the following Bathroom / toilet accessories of following make and fixing on the wall using C.P. brass screws, rawl plugs etc. as per manufacturer's requirement all complete at the locations shown and as directed by the Engineer In charge.

207.01 Toilet paper Roll Holder of Cera Brand 'Bold' Cat. No. F5013109FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207.02 Toilet paper Roll Holder of Cera Brand 'Bold' Cat. No. F5013109CH or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207.03 Towel rack 600mm Long with hook, Cera Cat No. F5014131FG or approved equivalent make. 0.000 Each Excess(+) Full Conversion INR

207.04 Towel rack 600mm Long, Cera Cat No. F5001101 or approved equivalent make. 0.000 Each Excess(+) Full Conversion INR

207.05 Coat Hook of Cera Brand 'Bold' Cat. No. F5013108FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207.06 Coat Hook of Cera Brand 'Hera' Cat. No. F5007108 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207.07 Liquid Soap Dispenser of Cera Brand 'Bold' Cat. No. F5013111FG or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207.08 Liquid Soap Dispenser of Cera Brand 'Montana' Cat. No. F5002111 or approved equivalent make 0.000 Each Excess(+) Full Conversion INR

207.09 Soap Dish Holder, French Gold Colour, Cera Cat No. F5014116FG or approved equivalent make, including necessary fittings and fixtures, complete as per specifications and as directed by Engineer-in-Charge. 0.000 Each Excess(+) Full Conversion INR

Soap Dish Holder, Chrome , Cera Cat No. F5014116CH or approved equivalent make, including necessary fittings and fixtures, complete as per specifications and as directed by Engineer-in-Charge. 0.000 Each Excess(+) Full Conversion INR

209 B : WATER SUPPLY SYSTEM

210 Supplying & fixing on Exposed surfaces the following sizes uv-stabilized Chlorinated Poly Vinyl Chloride (CPVC) pipes & Fittings of specified class having thermal stability for both hot & cold water supply consisting following items of work:- i) Supplying CPVC pipes and all required CPVC plain and brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS:15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40/80 for CPVC pipe having nominal size 65 mm (2½”) and above. ii) Supplying & providing providing CPVC/GI flanges, any other required specials and other jointing materials for connecting the CPVC pipe lines with spool pieces of water tank and for connecting the CPVC pipe lines with any fittings & fixtures etc., of the water supply line iii) Laying and fixing the pipe and specials on exposed surfaces/ underground, to correct line, level and plumb for water supply line, using metal straps (On wall surfaces) at 1.00 mtr. interval or as directed by the EIC. iv) Jointing the pipes and Specials using Solvent cement conforming to IS:15225 & Teflon tape ( For threaded joins ) of approved makes including cutting the pipe to required size, preparation of surfaces, necessary tools etc. all complete. v) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. vi) Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg / Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured. vii) CPVC pipes and fittings/ specials shall be of same brand. viii) Including removing existing GI pipe line with fittings and specials etc. NOTE: 1) The rate shall also include for cPVC pipe & specials required for making connections with the existing GI/ CPVC/PP-R/ UPVC/HDPE pipe line laid by other agency. 2) All threaded joints shall be made with brass threaded fittings only. 3) Exposed pipe fixing arrangement include providing & fixing slotted G.I. section & U clamps bolts arrangement for grouping of pipe. Sloted section thickness should not be less than 2mm.

210.01 20 mm(¾") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

210.02 25 mm (1") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

210.03 32 mm (1¼") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

210.04 40 mm (1½") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

210.05 50 mm (2") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

211 Supplying, fixing & concealing on wall / beams / columns etc. the following sizes UV- stabilised Chlorinated PolyVinyl Chloride (CPVC) Pipes & (male / female) brass threaded fittings Fittings of specified class having thermal suitable for both hot & cold water supply & suitable for fixing various fittings & fixtures such as taps, jet sray, wall mixture, concealed stop cock, flush valves etc., consisting following items of work :- i) Supplying CPVC pipes and all required CPVC plain/ and brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS:15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40 for CPVC pipe having nominal size 65 mm (2½”) and above. ii) Laying and concealing the pipe and specials for water supply by cutting/ making 75 mm X 75 mm groove on the wall, fixing the pipe using metal straps wherever required and filling the groove with cement mortar mixed with water proofing compound, after laying and testing the pipe line including making leak proof joints using cement solvent/ Teflon tape ( For threaded fittings) of approved make, cutting the pipe to required length, preparation of surface, necessary tools etc. all complete. iii) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. iv) Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg / Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured. v) CPVC pipes and fittings/ specials shall be of same brand. vii) Including removing existing GI pipe line with fittings and specials etc. NOTE:- 1) The rate shall also include for cPVC pipe & specials required for making connections with the existing GI/ CPVC/PP-R/ UPVC/HDPE pipe line laid by other agency. 2) All threaded joints shall be made with brass threaded fittings only.

211.01 20 mm(¾") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

211.02 25 mm (1") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

212 Supplying and laying below the ground or floor, the following diameter uv-stabilized Chlorinated Poly Vinyl Chloride (C-PVC) pipe line of specified class, consisting the following items of work:- i) Supplying CPVC pipes and all required CPVC plain / brass threaded fittings, SDR - 11 having thermal stability for hot & cold water supply of approved make conforming to IS:15778 with ISI mark for CPVC pipe having nominal size up to 50 mm and conforming to ASTM F 441 (IPS SERIES) Schedule 40/80 for CPVC pipe having nominal size 65 mm (2½”) and above. ii) Laying and fixing the pipe and specials below the ground or floor to correct line, level and plumb for water supply line. iii) Making leak proof threaded/welded joints. including cutting the pipe, cleaning, marking, jointing, etc. and including the cost of jointing materials. iv) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition. v) Providing and fixing C-PVC weldable / threaded fittings such as Union, Nipples, Bends, Elbows, Tees, Reducers, End caps, Couplers, Adaptors, Saddles, Plugs, Tank connectors, Expansion loops, Bypass bends, etc.vi) CPVC pipes and fittings shall be of same brand. vi) Testing the pipe line as per relevant code to a hydraulic pressure of 10 Kg/Sq.cm to assess leakages if any, rectifying the defect, retesting etc till water tightness of pipe line is ensured. vii) including removing existing GI pipe line with fittings and specials etc. Note:1) The rate shall also include for cPVC pipe & specials required for making connections with the existing GI / CPVC pipe line laid by other agency. 2) All threaded joints shall be made with brass threaded fittings Only. 3) Excavation and refilling shall be paid under relavent item.

212.01 50 mm (2") n.size (SDR-11 as per IS:15778) 0.000 RM Excess(+) Full Conversion INR

212.02 65 mm (2½") n.size (Schedule 40) 0.000 RM Excess(+) Full Conversion INR

213 Providing and Fixing Ball Valve as per relevant IS suitable for pipe pressure class with body of bronze and ball & stem of Stainless Steel of approved make with fittings & material for conectivity and labour, making water proof joints, including cost of jointing material and CPVC/UPVC/GI specials if required & testing the joints. etc complete as per directions of engineer-in-charge. NOTE: 1) Item Includes Flange jointing with required new flanges and hardware . 2) Wherever required union joint shall be provided in pipe to facilitate removal of valve. 3) Threaded fittings of CPVC/UPVC shall be of Brass Threaded only.

213.01 20 mm (3/4")n.size 0.000 Each Excess(+) Full Conversion INR

213.02 25 mm (1") n.size 0.000 Each Excess(+) Full Conversion INR

213.03 32 mm (1¼") n.size 0.000 Each Excess(+) Full Conversion INR

213.04 40 mm (1½") n.size 0.000 Each Excess(+) Full Conversion INR

215 C : DRAINAGE SYSTEM

216 Supplying and fixing following size uPVC UV-Stabilised soil / waste quality pipes and fittings ( SWR ) for soil, waste, vent, anti syphonage, HVAC waste pipe and rain water pipe lines consisting following items of work:- i) Providing and fixing uPVC UV-Stabilised Soil/ waste pipe as per IS:13592 and IS:14735 Type-B laid in floor & on Exposed faces of wall of approved make ii) Fixing the pipeline vertically by Metal clamps with rubber seal of approved make iii) Fixing the pipeline Horizontaly with specified slope below the ceiling by Metal clamps with rubber seal and GI hanger rods not less than 5mm dia at specified spacing, including all required hardware. iv) Providing and fixing uPVC cowl at the top of soil, waste water & vent pipe line. v) Providing and fixing uPVC P/S trap on line as per requirement for soil,waste water pipeline. vi) Laying the pipe below floor / ground to the slope and gradient equal to (or) steeper than 1 in 50, making leak proof connections of soil /waste pipe line from the shaft with inspection chamber / Manhole / Gully trap Chamber including the cost of filling around the holes of inspection chamber / Manhole / Gully trap with cement mortar 1:1 mixed with water proofing compound vii) Jointing the pipe / fittings with Solvent Cement & Rubber ring gasket with making holes in walls / floor grooving and redoing the same and brick support etc. Carrying out water-tightness test for the pipes laid as per codal provisions. Providing Ring Joint pipes at verticals and solvent cement jointed pipes at concealed locations. viii) Cutting the pipe to the required length including providing short pieces, necessary connectors, fittings & specials with & without door, assorted fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, single & double Y, vent cowl, gaskets, offsets etc. including providing necessary clean outs, cleaning pipe, extension pipe if any for clean outs, door bend, door elbow, door Y, socket plug, etc wherever required for accessing every segment of soil and waste pipes to enable removal of any Chock up after installation. ix) Providing necessary specials for connecting UPVC SWR (IS:13592/ IS:14735) pipe with UPVC (IS:4985) pipe etc x) Dewatering the pit/ trenches if necessary till completion of work xi) Testing the pipe line for any leakages, rectifying the leakages if any, retesting etc., till water tightness of the pipe line is ensured. xii) Exposed pipe fixing arrangement include slotted G.I. section and U clamps. xiii) including removing existing sewerage pipe line with fittings and specials etc. Note: Earthwork excavation for trenches shall be paid under relevant items For Soil & waste, Vent and Rain water pipe lines

216.01 75 mm dia. 0.000 RM Excess(+) Full Conversion INR

216.02 110 mm dia. 0.000 RM Excess(+) Full Conversion INR

217 Supplying, fixing & concealing on walls/ beams/ floors columns etc. the following sizes uPVC Pipes & Fittings of specified class consisting following items of work:- i) Supplying uPVC pipes conforming to IS:4985 and uPVC moulded plain / threaded fittings conforming to IS:7834 for waste water pipe line of approved make with ISI mark / equivalent approvals as per relevant standards, providing necessary specials for connecting UPVC (IS:4985) pipe with UPVC SWR (IS:13592) pipe etc. ii) Laying and concealing the pipe and specials for waste water by cutting/ making 75 mm X 75 mm groove on the wall, fixing the pipe using metal straps wherever required and filling the groove with cement mortar 1:3 mixed with water proofing compound, after laying and testing the pipe line including making leak proof joints using cement solvent/ Teflon tape ( Forthreaded fittings) of approved make, cutting the pipe to required length, preparation of surface, necessary tools etc. all complete. iii) Cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition (No Chases in RCC wall, column, beam, slab, chajja,etc shall be made with out getting the permission from Engineer In charge & structural design Enginner) iv) Concealing the pipes in wall, Laying the pipe below floor/ ground to the slope and gradient equal to (or) steeper than 1 in 50 v) Testing the pipe line for any leakages, rectifying the leakages if any, retesting etc., till water tightness of the pipe line is ensured. vi) including removing existing sewereage pipe line with fittings and specials etc. For Urinal/ wash basin/ Anti syphonic/ Sink waste. (10kg Pressure)

217.01 50 mm OD 0.000 RM Excess(+) Full Conversion INR

218 Providing uPVC Floor Trap/ Nahani Trap of following size having not less than 40mm effective water seal, fixing the trap in position and connecting with waste water pipe by cement solvent/ as per manufacturer's recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient, providing and fixing 150 x 150 mm size top tile with central strainer & flat cover/ flush strainer, closing the side inletes with plugs if required etc. complete all as per specification and as directed by the Engineer in charge.

218.01 Multifloor trap of 110 x 75 x 50 size of approved make or approved Equivalent 0.000 Each Excess(+) Full Conversion INR

218.02 3 pc top tile & flush strainer, mat finish, including Chilly /Cockroach Trap of approved make in plastic. or approved Equivalent 0.000 Each Excess(+) Full Conversion INR

218.03 Nirali 'Calnzo Range' Luke Floor Trap Cover, 150×150 mm Size, glossy AISI 304 SS, corrosion & rodent/cockroach resistant, perforated locking grating with 12 mm tile insert, complete as directed or approved Equivalent 0.000 Each Excess(+) Full Conversion INR

219 Supplying and fixing under-sink S.S Grease Trap of M/s. ACO make or approved equivalent, complete with inlet, outlet, and removable strainer, including all necessary fittings and connections as required and complete as per direction of Engineer-in-Charge.

219.01 Aco Model GT120 Size 800mm x500mm x445mm 0.000 Each Excess(+) Full Conversion INR

219.02 Aco Model GT40 Size 540mm x400mm x325mm 0.000 Each Excess(+) Full Conversion INR

220 Providing & laying UPVC under ground drainage pipes & Fittings of Approved make for storm water drains & Sewer lines of following size conforming to IS:15328 to proper level & grade, jointing including providing coupler with solvent cement / welded joints / as per manufacturer's requirement, encasing the pipe alround using cement concrete 1:3:6 complete if required all as per specifictions, drawing and as directed by the E.I.C. item includes Providing and fixing UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc For Sewer line and Storm water Drains NOTE:- Cement concrete for encasing shall be paid under relevant item.

220.01 110 mm DN (SN 8kN/m²-SDR34) 0.000 RM Excess(+) Full Conversion INR

220.02 160 mm DN (SN 8kN/m²-SDR34) 0.000 RM Excess(+) Full Conversion INR

221 Providing and fixing factory-made FRP Readymade Modular Toilet, Bathrooom Block of approved series of Supreme 'Cleanage' or EPS panels of TATA Ezynest or approved equivalent. The unit shall be supplied and installed complete with door shutter, anti-skid flooring, ventilation louvres, required traps, approved make CP bib tap, internal CP and sanitary fittings, plumbing inlet and outlet connections properly integrated with the existing water-supply arrangement and internal sewerage & waste-water pipe connection from trap up to the existing manhole/inspection chamber,electrical point provision,etc all as directed by the Engineer-in-Charge. Note: Water supply line upto the toilet block & External sewerage pipeline beyond the toilet block, connecting to the existing chamber/manhole, shall be measured and paid separately under the relevant item.

221.01 Modular Toilet Block – with IWC Base (Without Tank) 0.000 Each Excess(+) Full Conversion INR

221.02 Modular bathroom Block (Without Tank) 0.000 Each Excess(+) Full Conversion INR

223 D : CIVIL WORKS CONTINGENT TO PH WORKS

224 Earth work excavation in foundation pits, plinth/ tie beams, tank, trenches, loose boulder for pipe line, chamber etc. in all soils other than soft & hard rock up to depths mentioned below including shoring if necessary, dressing the sides, trimming, ramming, dewatering and preparing the bed for foundation and refilling around the foundation and in plinth with selected excavated earth, in layers not exceeding 200 mm thick, watering, consolidation to obtain 90% proctor density and disposing of the surplus material within a distance of 150 m etc. complete as per specifications, drawings and as directed by the Engineer-in-charge.

224.01 Depth not exceeding 1.5 m from ground level 0.000 cum Excess(+) Full Conversion INR

225 Earth work excavation in foundation pits, plinth/ tie beams, tank, trenches, pipe line, chamber etc. in soft rock upto depths mentioned below including shoring if necessary, dressing the sides, trimming, ramming, dewatering and preparing the bed for foundation and refilling around the foundation and in plinth with selected excavated earth, in layers not exceeding 200 mm thick, watering, consolidation to obtain 90% proctor density and disposing of the surplus materialwithin a distance of 150 m etc. complete as per specifications, drawings and as directed by the Engineer-in-charge.

225.01 Depth not exceeding 1.5 m from ground level 0.000 cum Excess(+) Full Conversion INR

226 Earth work excavation in foundation pits, plinth/ tie beams, tank, trenches, pipe line, chamber etc in hard rock by chiselling or by using machine such as Poclain with Jack hammer etc. upto depths mentioned below including shoring if necessary, dressing the sides, trimming, ramming, dewatering and preparing the bed for foundation and refilling around the foundation and in plinth with selected excavated earth, in layers not exceeding 200 mm thick, watering, consolidation to obtain 90% proctor density and disposing of the surplus material within a distance of 150 m etc. all complete as per specifications, drawings and as directed by the Engineer-in-charge.

226.01 Depth not exceeding 1.5 m from ground level 0.000 cum Excess(+) Full Conversion INR

227 Disposing off the surplus excavated materials beyond initial lead by mechanical transport to the near by Local Municipal Authority approved dumping pits/ dumping area outside campus including all leads, lifts, loading, unloading, stacking, spreading, levelling etc. complete as per drawings, specifications & as directed by the Engineer in charge. The disposal shall be as per latest guidelines of Construction & Demolition waste management plan as approved by Local Municipal Authority. Royalty for transportation, disposal of Rock, spreading etc. including obtaining permission from statutory authority, if any shall be borne by the contractor. Note: Voids @ 20% for soils and 50% for soft rock/ hard rock shall be deducted from fully loaded truck measurements to arrive at the net quantity for payment in case direct measurement is not possible. 0.000 cum Excess(+) Full Conversion INR

228 Providing and laying in position, at all floors and at all levels & locations plain cement concrete of grade as specified below including machine mixing, consolidation, finishing, curing and including cost of form work, shuttering, centering etc. complete all as per specifications and directed by EIC. (Note:- Reinforcement provided if any shall be measured & paid under relevant item.)

228.01 Cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) for pedestal, encasing,etc 0.000 cum Excess(+) Full Conversion INR

228.02 Cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) for pedestal, encasing,etc 0.000 cum Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Select, Excess (+), Less (-) Less (-)

Tender Inviting Authority: Chairman GB

Name of Work: Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No: DCSEM/CQD/QSB/25-26/NIT/75 dt.19.02.2026

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

300 PART - III : ELECTRICAL WORKS

301 Disconnection & dismantling of the all existing electrical accessories like switches, sockets, ceiling roses, switchboards, wiring, cables, old lighting fixtures etc. in the area under renovation as per the drawings attached.

301.01 Single Room 0_);0 Job/ Room Excess(+) Full Conversion INR

301.02 Suites 0_);0 Job/ Room Excess(+) Full Conversion INR

301.03 Conferrence & Lan room 0_);0 Job/ Room Excess(+) Full Conversion INR

301.04 Other rooms 0_);0 Job/ Room Excess(+) Full Conversion INR

302 Point wiring: Providing point wiring for light / ceiling fan / 16A socket outlet/AC point etc. with 1100V grade, FRLS PVC insulated multi stranded copper wires in existing concealed conduit and / or providing concealed/surface conduit and / or 25mm x 16mm size white / ivory PVC casing capping on surface, controlling modular switches on ready made fire retardant plastic boxes/readymade concealed GI switch boxes with cover plate & metal frame, angle / batten pendent lamp holders ,PVC round plates, 6A connectors in concealed junction boxes , ferrule numbers on both sides, 1.1kV grade FRLS PVC insulated copper conductor wires for earthing of above said specifications, labelling etc. all as per site conditions, specifications, drawings and as instructed by Engineer-in-charge. Scope of work shall also includes providing the tags for wires inside casing & capping for bunching to avoid hanging of wires at the intervals of 600mm. Note: 1. Wiring layout arrangement and samples of switch boxes are to be got approved prior to procurement. 2. All switches, sockets, cover plates & frame, surface boxes, etc. shall be of approved colour & shall be of same make and other accessories like lamp holders, ceiling roses etc. shall be of polycarbonate body and shall preferably ISI marked. 3. The dimensions of switches, sockets, and fan regulators shall preferably be ISI mark. 4. HMS PVC sleeves will have to be provided for crossing the wall, drilling holes & it’s refinishing to be also included in the scope. 5.The scope of work also includes removing of existing MS switch boards by breaking the brick wall, making suitable cut-outs in brick wall for fixing new switch boards, finishing with cement mortar, applying white putty as required,touchup painting for that area with OBD paint of existing shade and as per instructions of E-I-C. 6. All metallic boxes/switch boxes shall be earthed with 1.1kV grade FRLS PVC insulated 1.5sq.mm copper flexible wire.

302.01 Light , Fan , 6A Socket , bell points etc. ( Point wiring from Key card switch near door of each room ) Primary light point with 1.5 sq.mm wires complete with 6A, 240V controlling switch. 0_);0 Point Excess(+) Full Conversion INR

302.02 Light , Fan , 6A Socket , bell points etc. ( Point wiring from Key card switch near door of each room ) Secondary light point with 1.5 sq.mm wires 0_);0 Point Excess(+) Full Conversion INR

302.03 Light , Fan , 6A Socket , bell points etc. ( Point wiring from Key card switch near door of each room ) Ceiling fan point with 1.5 sq.mm wires complete with 6A, 240V controlling switch, 5 step 100W fan regulator. 0_);0 Point Excess(+) Full Conversion INR

302.04 Light , Fan , 6A Socket , bell points etc. ( Point wiring from Key card switch near door of each room ) 6 A socket outlet point with 1.5 sq. wires complete with 6A, 240V socket outlet with 6A, 240V controlling switch. 0_);0 Point Excess(+) Full Conversion INR

302.05 Light , Fan , 6A Socket , bell points etc. ( Point wiring from Key card switch near door of each room ) Door bell point with 1.5 sq.mm wires bell push near door & modular chime bell on switch board inside room. 0_);0 Point Excess(+) Full Conversion INR

302.06 Light , Fan , 6A Socket , bell points etc. ( Point wiring from Key card switch near door of each room ) Exhaust fan point with 1.5 sq. wires complete with 6A, 6 A socket outlet point near exhaust fan & 240V socket outlet with 6A, 240V controlling switch on switch board. 0_);0 Point Excess(+) Full Conversion INR

302.07 Power Points Directly from DB. 16 A socket outlet point with 2.5 sq. mm wire complete with 6/16A, 3 pin socket outlet 3 module with 16A SP, 250V 1 way controlling switch 0_);0 Point Excess(+) Full Conversion INR

302.08 Power Points Directly from DB. AC point with 4 sq.mm wire complete with 25A DP MCB C curve with enclosure as controlling switch including all accessories. 0_);0 Point Excess(+) Full Conversion INR

302.09 Power Points Directly from DB. Water Heater point with 4 sq.mm wire complete with 25 DP MCB C curve with enclosure as controlling switch including all accessories. 0_);0 Point Excess(+) Full Conversion INR

Supply, installation, testing & commissioning 15A 230V modules key card switch ( 2 module ) similar to cat. No 572244 with key fob similar to cat no572259 of M/s Legrand for each room on 4 module readymade concealed GI switch boxes with cover plate & metal frame, blank plate, 4 ways 16A connector, etc. all as required & instructed by E-I-C. The modular key card switch shall be of approved colour & shall be of same make of switch. 0_);0 each Excess(+) Full Conversion INR

303 Casing capping & Conduit Pipes : To be used for TV, Telephone, LAN cables, etc. or in case existing conduit found rusted.

303.01 Supply installation testing & commissioning of 25 x 16 mm casing – capping on surface of slab / wall / column fixed with nylon / rawal plug, GI wood screws at the intervals of 300mm includes providing the tags for wires inside casing capping for bunching to avoid hanging of wires at the intervals of 600mm as per the instruction of Engineer-in-charge. 0_);0 M. Excess(+) Full Conversion INR

303.02 Supply installation testing & commissioning of 25 dia rigid HMS PVC of conduit with all required accessories like junction box , bend, etc. on surface of slab / wall / column fixed with PVC spacer saddles , nylon / rawal plug, GI wood screws at the intervals of 300mm as per the instruction of Engineer-in-charge. 0_);0 M. Excess(+) Full Conversion INR

303.03 Supply installation testing & commissioning of 25 mm dia FRPP flexible conduit with PVC gland on surface of slab / wall / column fixed with PVC spacer saddles, nylon / rawal plug, GI wood screws as per the instruction of Engineer-in-charge. 0_);0 M. Excess(+) Full Conversion INR

303.04 Making of grooves by cutting the floor tiles /floor/wall with cutter machine and supply & laying HMS PVC of 25 dia rigid conduit with all required accessories line junction box , bend, etc. for laying power & control cable/ wires as required, refilling the grooves with cement concrete & finishing the surface to floor level as required. 0_);0 M. Excess(+) Full Conversion INR

304 Supply installation testing & commissioning of 2nos of 2.5 sq.mm & 1no. of 1.5sq.mm FRLS grade 1.1 kV PVC insulated flexible multi-stranded copper wires in existing concealed conduit/casing capping with including termination of wires with suitable copper lugs at DB/MCBs near door as required and instructed by EIC. 0_);0 RM Excess(+) Full Conversion INR

305 Distribution Boards

305.01 8 Ways ETPN PDB Supply, installation ,testing & commissioning of readymade double door 8 way ETPN DB having IP43 protection, Plain look with rounded corners, door knob, similar to model No.:5076 72 of M/s Legrand make complete with wiring kit, neutral link, earth link etc., ready made cable end box of same make including providing following components as required & instructed by the Engineer-in-charge. i) 63A RCCB, 2P, 30mA sensitivity,2 module - 3 nos. ii) 6-25 A, 10kA breaking capacity ,C-curve, SP, MCB - 18 nos. iii) 63A 10kA breaking capacity ,C-curve, FP, MCB - 01 no. iv) PPI kit -01 no. Scope of work include : i) Providing Danger board, MCB blanks, Schematic Diagram, Ferule numbers, etc. ii)DB shall be concealed in place of existing concealed flat DB including dismantling & breaking of wall, removal of the existing one & reinstatement by applying mortar & white cement/POP etc. DB shall be installed such that the existing concealed conduits to be matched with cable end box of DB. 0_);0 Job Excess(+) Full Conversion INR

305.02 8 Ways ETPN LDB Supply, installation ,testing & commissioning of readymade double door 8 way ETPN DB having IP43 protection, Plain look with rounded corners, door knob, similar to model No.:5076 72 of M/s Legrand make complete with wiring kit, neutral link, earth link etc., ready made cable end box of same make including providing following components as required & instructed by the Engineer-in-charge. i) 40A RCCB, 2P, 30mA sensitivity,2 module - 3 nos. ii) 6-25 A, 10kA breaking capacity ,C-curve, SP, MCB - 18 nos. iii) 40A 10kA breaking capacity ,C-curve, FP, MCB - 01 no. iv) PPI kit -01 no. Scope of work include : i) Providing Danger board, MCB blanks, Schematic Diagram, Ferule numbers, etc. ii)DB shall be concealed in place of existing concealed flat DB including dismantling & breaking of wall, removal of the existing one & reinstatement by applying mortar & white cement/POP etc. DB shall be installed such that the existing concealed conduits to be matched with cable end box of DB. 0_);0 Job Excess(+) Full Conversion INR

306 Recess mounted LED lighting Fixture

306.01 Supply, installation, testing & commissioning of 1200Lm Round LED recess mounted fixture similar to model no. DN282 LED12S-6500 PSE WH R of M/s. Philips, complete with frame, accessories & additional support safety chain from surface of slab/beam by 6 mm anchor fasteners / suitable coach screw etc. required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

306.02 Supply, installation, testing & commissioning of 600 Lm round LED recess mounted down light fixture of dia 75mm similar to model no. RS261B LED6S/865 PSU MB WH S1 of M/s. Philips, complete with accessories & additional support safety chain from surface of slab/beam by 6 mm anchor fasteners / suitable coach screw etc. required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

306.03 Supply, installation, testing & commissioning of LED strip light with Aluminium profile & driver similar to model no. Pro Glow LED Strip Light 45W with Driver of M/s. Philips, complete with accessories & required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

306.04 Supply, installation, testing & commissioning of LED strip light with driver similar to model no. Pro Glow LED Strip Light 45W with Driver of M/s. Philips, complete with accessories & required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

307 LED lighting Fixture

307.01 Supply, installation, testing & commissioning of Floor standing light fixture similar to architectural drawing attached complete with accessories & required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

307.02 Supply, installation, testing & commissioning of Table light fixture similar to architectural drawing attached, complete with accessories & required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

307.03 Hexagonal Slim Surface LED Light Supply, installation, testing & commissioning of 20W Hexagonal Slim Surface LED Light fixture similar to model no. Philips Hexa Rimless LED Surface light of M/s. Philips make with CCT 2700/4000/6500K, complete with accessories on false ceiling / slab / beam by suitable anchor fasteners / coach screw/ SS screw etc. required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

307.04 Picture light Supply, installation, testing & commissioning of 420 lm, 12W LED Wall light fixture similar to model no. 31403 Muziris of M/s. Philips make, complete with accessories on wall/ slab / beam by suitable anchor fasteners / coach screw/ SS screw etc. required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

307.05 Wall light Supply, installation, testing & commissioning of LED Wall light fixture similar to photo attached of reputed make, complete with suitable 9W Full Glow Glass LED Lamp similar to M/s Philips & with all accessories on wall/ colomn / beam by suitable anchor fasteners / coach screw/ SS screw etc. required hardware as required & instructed by E-I-C. 0_);0 each Excess(+) Full Conversion INR

308 Ceiling fan & Ceiling fan hook

308.01 Supply installation, testing & commissioning of 1200 mm BLDC Ceiling fan similar to Aris Contour Smart of M/s Atomberg with safety chains including interconnection to ceiling rose with 3C X 1.0 sq.mm flexible copper cable. 0_);0 each Excess(+) Full Conversion INR

308.02 Supply installation, testing & commissioning of 900 mm BLDC Ceiling fan similar to Aris Contour Smart of M/s Atomberg with safety chains including interconnection to ceiling rose with 3C X 1.0 sq.mm flexible copper cable. 0_);0 each Excess(+) Full Conversion INR

308.03 Supply installation, testing & commissioning of 200 mm BLDC Exhaust fan similar to Efficio of M/s Atomberg with 3C X 1.0 sq.mm flexible copper cable & 3pin top. 0_);0 each Excess(+) Full Conversion INR

308.04 Providing Ceiling fan hook fabricated out of 120mm x 120mm x 8mm (Approx.) MS sheet with 12mm MS rod hook welded on MS sheet, holes on corners & painting with two coat of enamel paint over one coat of red oxide and with four nos. of anchor fasteners 10mm dia ( Approx.), all as required & instruction of Engineer-in-charge (Sample to be got approved) 0_);0 each Excess(+) Full Conversion INR

309 Supply installation, testing & commissioning of 15 Ltr Storage type water heater similar to Elegance slim model of M/s AO smith operating on 240V AC ,50Hz supply complete with all accessories. ISI marked, connecting to water heater point with minimum 3C X 1.5 sq.mm copper conductor flexible chord. 0_);0 each Excess(+) Full Conversion INR

310 Telephone Point Wiring : Point wiring with 2 pair 0.5mm copper conductor PVC insulated telephone cable, in existing concealed conduit / 25 x 16mm size white/ivory PVC casing capping on slab/column/beam/wall complete with all accessories, RJ-11 telephone socket outlets with shutter ferrule numbers on both side of the circuits all terminations with ferrule /lugs if required, labelling all as per drawing specifications & as per instructions of E-I-C. NOTE: 1. Point wiring means 2 pair telephone cable from Telephone Tag Block to assigned point including end termination of one pair at both sides and other pairs should be kept spare. 2. Make of Telephone socket, plate, box shall be same as electrical switches and sockets with the approval of E-I-C. 0_);0 Point Excess(+) Full Conversion INR

311 Smoke detector & RI

311.01 Disconnection & dismantling of existing wires and supply, installation, testing & commissioning of 2 nos of 1.5 sq.mm FRLS grade 1.1 kV PVC insulated flexible multi-stranded copper wires in existing concealed conduit/casing capping with including termination of wires with suitable copper lugs at smoke detector / fire alarm panel as required and instructed by EIC. 0_);0 RM Excess(+) Full Conversion INR

311.02 Disconnection & dismantling of existing smoke detector and Supply, installation testing & commissioning of Conventional photo electric smoke detector similar to RE-316S 2L of M/s Ravel make with dual Blinking LED, operating voltage of 9vdc to 33 vdc,100 mm base, The detector shall supports response indicator, shall be UL listed &IP 42 rating as per the instructions of EIC. 0_);0 each Excess(+) Full Conversion INR

311.03 Disconnection & dismantling of existing heat detector and Supply, installation testing & commissioning of Conventional heat detector similar to RE-316H 2L of M/s Ravel make with dual Blinking LED, operating voltage of 9vdc to 33 vdc,100 mm base, The detector shall supports response indicator, shall be UL listed &IP 42 rating as per the instructions of EIC. 0_);0 each Excess(+) Full Conversion INR

311.04 Disconnection & dismantling of existing Responce indicator (RI) and supply, installation, testing & commissioning of conventional RI including termination of wires with suitable copper lugs at smoke detector / RI panel as required and instructed by EIC. 0_);0 each Excess(+) Full Conversion INR

311.05 Supply, installation testing & commissioning of Conventional gas (CO) detector similar to RE-386CO with base of M/s Ravel make with operating voltage of 21vdc to 27 vdc,100 mm base, the detector shall supports existing fire alarm panel all as per the instructions of EIC. 0_);0 each Excess(+) Full Conversion INR

312 Dismantling and safe removing the old existing wall mounted split air conditioner along with pump down refrigerant in the system, safely remove its copper piping & packing of existing piping holes etc. and Re-installation, testing & commissioning of same AC including inter connecting copper piping, cabling, drain piping between IDU to ODU, fabrication work, leak testing for entire system, vaccumising using vacuum pump with suitable refrigerant charging as per installation manual, for smooth operation of AC`s etc. complete all as per the instructions & to the entire satisfaction of EIC. NOTE: 1)Copper pipe, drain pipe, Cables, fabrication work will be paid separately in relevant item of SOQ. complete all as per requirement and instructed by EIC. 0_);0 each Excess(+) Full Conversion INR

313 Refrigerant piping with rubber nitrile insulation: Copper piping for refrigerant as per site situation with necessary structural clamps/ supports/ bends/ elbows/ reducers/U-bends/ flare nuts/ adapters/any other brass fittings as required etc. with insulation and wrapped with monsoon tape all as per AC`s manufacturer's standards.

313.01 12.7 mm (1/2)'' with 10 mm rubber nitrile 0_);0 RM Excess(+) Full Conversion INR

313.02 6.4 mm (1/4)'' with 10 mm rubber nitrile 0_);0 RM Excess(+) Full Conversion INR

314 PVC drain piping of size 25 mm/32 mm diameter duly insulated with heatlone sheet, etc. complete all as per the site condition & instructed by EIC. 0_);0 RM Excess(+) Full Conversion INR

315 Control cabling with adequate size of copper conductor wire/ power cable to connect outdoor units with respective indoor units & power cable to connect power outlet to ODU/IDU complete with lug connections etc. complete all as per site situation as required & instructed by the Engineer –in – charge.

315.01 4 core x 2.5 sq.mm cable 0_);0 M. Excess(+) Full Conversion INR

315.02 3 core x 2.5 sq.mm cable 0_);0 M. Excess(+) Full Conversion INR

316 Replacement of 62.5 kVA DG set with 125kVA/100KW 3 phase Gas Genset : Disconnection & dismantling of existing DG set and Supply, assembly, installation, pre commissioning testing at site & commissioning of 3 phase, 415 volts,125 kVA Gas gen set Prime Rated, radiator cooled, 7.2 Lm Power engine coupled with 125KVA electric alternator, microprocessor based Controller, Silencer, Anti-Vibration mountings, exhaust flexible connector, Batteries with cables, Acoustic Enclosure with Auto Manual Control Panel, etc. as per the specification and as instructed by EIC. Note:- The Gas Generator set shall conform to latest emission limits stipulated in Central Government Notification dated 03.11.2022 of Central Pollution Control Board latest norms for emissions & implemented w.e.f. 01.07.2023 or latest amendment in Pollution norms laid by Statutory authority. Clearance / Approval of complete installation from CPCB / State Pollution Control Board, Central Electricity Authority, other licensing authorities wherever required are in the scope of work. All payments towards fees / registration charges shall be made by DCSEM / D.A.E. and receipts shall be got prepared in the favour of authorities making payments. Quoted rates shall be inclusive of (i) Providing Gas pipe line connection at Guest house premises, preparation of layout drawings, follow up of necessary applications, liaison with all Govt. bodies for statuary approvals. (ii) Modification in existing DG Foundation as per drawings approved by department including earth excavation up to required depth, soling, Reinforced Cement Concrete of grade M-30 ,Providing, laying & binding FE-500 grade steel, removing & fixing of shuttering with MS plate and disposing of the surplus earth to NDMC approved dumping ground etc. and any other materials which is required for foundation all complete as per specifications, drawing and as directed by the Engineer in Charge. (iii) Supply, installation, testing and commissioning of suitable size MS exhaust piping, as per specifications. The outdoor exhaust piping shall be supported by free standing MS structure with RCC foundation & shall be got approved by EIC before execution & as per technical specifications. MS structure consisting of MS channel/angle / flat/ chequered plate /MS rod hangers etc. including painting with one coat of primer and two coats of epoxy paint of approved shade. (iv) Removal & reinstallation of existing power cable terminations. (v)Dismantling the existing DG set , AMF panel , oil tank, switches, etc. & including, loading and unloading , taking away from site. Necessary gate passes shall be issued by Dept. Rebate for taking away the DG set shall also be included in unit rate quoted. 0_);0 Job Excess(+) Full Conversion INR

317 Earth Station: Providing earth station with heavy dipped GI earth plates electrode 600 x 600 x 6.0 mm in size at the depth minimum of 2.5 m below ground level (bottom of Plate) confirming to IS 3043 complete with all required materials like coke / charcoal, salt, G.I nut bolts, washers, 19 mm dia GI pipe (B class), 150 mm thick concrete wall chamber duly plastered having size of 500 x 500 x 500 mm, heavy duty (minimum 6 mm thick) M.S chequered plate cover, associated materials like 40 x 40 x 5 mm angle iron frame work, hinged locking arrangements, complete with funnels, GI test links (50 x 6 mm), two runs of 25 x 6mm G.I strips for connecting G.I plate & test link etc. including excavation of ground in all types of soils, refilling & removal of excess earth within a radius of 3000 m etc. all as required & instructed by the Engineer-in-charge. Note:- 1. The chamber cover & frame shall be got approved by Department & painted with two coats of red oxide & one coat of enamel paint. 2. Painting of earth value & test date on cover plate. 3. Earthing strips shall be welded with the earthing plate before galvanizing & two holes on each strip & plate shall be made for fixing the screws. 0_);0 Job Excess(+) Full Conversion INR

318 Supply, installation, testing & commissioning of hot dipped following GI strip fixed to wall / slab / column / beam with heavy duty GI spacer saddle or in ground at a depth of 750 mm below ground level including excavation in all type of soil , interconnection of earth strip / wire GI nut bolts & washers, painting with two coats of black bituminous compound for earth strip in ground and green colour enamel painting strip on surface etc. all as required & instructed by the Engineer-in-charge 0_);0 M. Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Select, Excess (+), Less (-) Less (-)

Tender Inviting Authority: Chairman GB

Name of Work: Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No: DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

400 PART - IV : CCTV WORKS

401 Supply, installation, testing and commissioning of following IP based video surveillance CCTV cameras fixed on pole/wall/ceiling etc. with all recommended mounting hardware & accessories etc., all as per technical specification, scope of work, GTP, pre bid clarification as per requirement to achieve intended functions and as per instruction of Engineer in charge. Note: all type labelling ,cable dressing and termination of all cable in scope of agency as per instruction of EIC.

401.01 IP bullet IR outdoor camera 2MP or better 0_);0 each Excess(+) Full Conversion INR

401.02 Panoramic outdoor Camera 0_);0 each Excess(+) Full Conversion INR

402 Supply, installation, and configuration of a Network Video Recorder (NVR) with the minimum technical specifications given in Scope of work, GTP suitable for enterprise-grade surveillance systems. Note: NVR should be support min 32 channel with full HD recording 90 Days and support minimum 100 Tb or Higher storage capacity and min 2 Video Monitoring Port VGA/ HDMI x 2 LAN 100/1000 Base X 2 and Dual Redundant Power Supply Unit. 2)Details Specification Given in the Scope of work, GTP 3)Earthing of the NVR in the scope of the agency. If existing earthing is not available in the nearby area, the agency should make separate arrangements for the same, without any additional cost. 0_);0 each Excess(+) Full Conversion INR

403 Supply, installation, and commissioning of a professional-grade 43-inch LED monitor designed for 24/7 continuous operation, suitable for control rooms, surveillance systems, digital signage, or professional display environments with 3yr Warranty. Notes: 1)Monitor should be designed for professional environments, not consumer-grade TVs. 2)Vendor must ensure all accessories and mounting hardware are included. 3)Must support continuous usage without risk of burn-in or overheating. 4)Note: The supply of HDMI cables / HDMI extender adapters for the connection of the redundant NVR is within the scope of the agency, with no additional cost. 0_);0 each Excess(+) Full Conversion INR

404 Switch: 24 port manageable fully loaded with copper and LX modules, Layer 2 Ethernet switches with PoE minimum 4, 1000/10000 base T ports and minimum 16 nos. 10 Gigabit uplink LX ports. The switching engine shall have a switching speed of at least 480 Gbps. Note: Details Specification given in the scope of work and GTP 0_);0 each Excess(+) Full Conversion INR

405 Switch: Supply, installation, testing & commissioning of Layer 2 managed industrial switch 8 X 10/100/1000 Tx, POE/POE++ with 2 nos gigabit copper & SFP combo ports conforming to following features: 5.6 Gbps Switching capacity, Supports 10/100/1000 Mbps SFPs, Up to 8K MAC address table, Redundant power inputs, IP-30 Metal Case, Support X-Ring function, SNMP v1/v2c/v3, Web, Telnet, CLI Management TFTP firmware update, system configure restore and backup. Provides standards-based IEEE 802.3af. Power over Ethernet - 8 ports of class 3 powered devices at 15.4 watts. Alternative A mode. Ingress Packet Filter and Egress Packet Limit, all as per instruction of Engineer in charge. Scope includes supply of SMPS, SFP modules 2 nos, and all copper port fully loaded. Note: 1. Better switch configuration is acceptable. 2. Switch to be Din rail mountable. 3. SMPS should be compatible with switches and shall be pre-approved before procurement. 0_);0 each Excess(+) Full Conversion INR

406 Outdoor Junction Box: Supply, installation, testing & commissioning of out door junction Box (wall/pole mounted) all as per specification and scope of work & as per instruction of engineer in charge. Note:1)Earthing of the Junction Box in the scope of the agency. 0_);0 each Excess(+) Full Conversion INR

407 Power Cable: Supply, installation, glanding, termination with copper lugs/ terminal connectors etc., testing and commissioning of 3C X 1.5 sq.mm armoured copper conductor power cable all as per specification and scope of work & as per instruction of Engineer in charge. Note: After laying of cable before charging megger report shall be submitted

407.01 Laying on surface /existing trench/in existing pipe with clamps/saddles etc. 0_);0 M. Excess(+) Full Conversion INR

407.02 Laying in ground including excavation in all types of soil/ footpath including paver block removal, excavation, normalisation to original finish, sand bedding, brick protection etc. Note: 1. Excavation in ground up to 750 mm deep. In paver block up to 12" deep. In garden up to 12" or 18" deep as per site condition. No excess payment shall be made for level matching excavation. 2. Providing sand bedding and baked bricks (approx. 18 nos per Metre) for laying of power/control cable. 3. Cutting of road / Breaking of PCC shall be carried out on the plain area including back filling as per the site requirement. Depth of the excavated trenches shall be decided by E-I-C as per site conditions & requirement. Permanent re- instatement at site and disposal of excavated excess debris to be shifted away from site 0_);0 M. Excess(+) Full Conversion INR

408 CAT 6A: Supply, drawing through existing pipe / on wall/column/pole etc., testing and commissioning of 4-pair outdoor CAT-6A UTP(outdoor Use) unarmoured cable, with all accessories. There shall be multiple segments of various lengths as per site requirement. Scope includes providing RJ-45 standard connector at both ends of each segments as per site requirement and all as instructed by engineer in charge. Note: 1. Pre-despatch inspection to be offered for the CAT-6A UTP(outdoor)Cable. 2. After laying of Cat 6 A UTP cable test by fluke meter is to be carried out abd report of the same is to be submitted to the department. 3.Termination of CAT6A UTP cable in Patch panel In the Scope Of agency 0_);0 M. Excess(+) Full Conversion INR

409 High Density Poly Ethylene Pipe: Supply and installation of 40 mm dia PLB HDPE pipe for UG CAT6 A Cable with 4 mm dia polypropylene rope as per TEC/GR/TX/CDS- 008/03/MAR-11 or TEC/GR/FA/CDS-008/04/AUG-19 specifications with following accessories/fittings/details/parameters: Accessories: 1. Cable Sealing Plug ,Straight joints (couplers) ,Tee joint for Duct in scope agency without any extra cost. 2. With marking on duct as "DCSEM IT SECTION"

409.01 In ground including excavation in all types of soil/ footpath including removal of paver blocks and all reinstatement as per original finish. Note: 1)Asphalt road are to be refinished with cement/bituminous compound and removed tiles of foot path to be re laid after laying of pipe. Trenches on soft soil require to be refilled with excavated earth materials . 2) Excavation in ground up to 600 mm deep. paver block/garden up to 12 " deep. No excess payment shall be made for level matching excavation. 0_);0 M. Excess(+) Full Conversion INR

409.02 Existing trench/on surface /wall/column/pole with all accessories including GI clamp etc. 0_);0 M. Excess(+) Full Conversion INR

410 GI pipe: Supply & installation of following Hot dipped class B, G.I pipe of following sizes: Note: Asphalt road are to be refinished with cement/bituminous compound and removed tiles of foot path to be re laid after laying of pipe. Trenches on soft soil require to be refilled with excavated earth materials .

410.01 Size 32mm dia GI pipe On pole/column/ trench with G.I clamp all as per instruction of Engineer in charge. 0_);0 M. Excess(+) Full Conversion INR

411 Supply and installation of 25 mm dia High mechanical stress (HMS) rigid PVC conduit having ISI marked IS 9537 Part - 3, including fixing accessories & hardware concealed /exposed in slab/wall or on 5mm.thick G.I. spacers fixed with no. 10 nettle fold wood screws with nylon plug complete with all conduit accessories 0.9mm G.I. Saddles, all as per attached specifications and scope of work and as per instruction of Engineer in charge. 0_);0 M. Excess(+) Full Conversion INR

412 Supply and installation of 25x16 mm PVC casing and capping all as per attached specifications and scope of work and as per instruction of Engineer in charge. 0_);0 M. Excess(+) Full Conversion INR

413 SITC of CCTV pole for mounting of CCTV cameras Fabrication, supply & erection of hot dipped galvanised MS,ERW tubular pole of 3.5m height above finished surface level of Size 114.3mm(OD) x3.65 mm thickness as per IS1161, welded with Base plate size 300x300x6 mm a the bottom of PCC.Scope includes excavation of asphalted road, making 1:2:4 PCC foundation 500x500x350 mm deep below in level and 400mm dia, 350 mm above finished surface level. with Accessories as below: 1. Anchor bolt covers as specified. 2. Weather heads and couplings. 3. Pole cap. 4. Cabinet mounting fittings, plates, brackets as needed. 5. Reinforced couplings for wire entrances to cabinets. 6. Ground rod, including wiring, pole earthing 7.Mounting Brackets: 360 degree adjustable 0_);0 each Excess(+) Full Conversion INR

414 SITC of 2 KVA Online UPS equipped with SNMPcard, complete with wiring from UPS to existing power point and to PDU devices in the 19" rack ( to be mounted in 19 " rack) suitable to fit 600mm Depth in 12 U Rack 0_);0 each Excess(+) Full Conversion INR

415 Supply & installation of double section 19" wall mounted, 12U height & 600 mm depth, network Racks with all mounting accessories like anchor fasteners or as per instruction of E.I.C. as given below 1. Rack having safety toughened glass door. 2. Rack shall be steel metal and frame made out of heavy grade Aluminium extrusion and shall be powder coated deep Gray (RA-7037). 3. Rack shall be provided with following integral accessories. a. Fans (230 V AC)- 2 nos. b. Horizontal cable manager - 4 nos. c. AC power panel with 6 nos of 5A 3 pin socket with suitable switch and spike guard and 6A SP MCB control and power cord of 3 Core, 1.5 sqmm, 1.5 m. d. Wall mounting hardware and cage nut etc. all as required. e. Blanking plates: 2U - 2 nos. & 1U - 4 nos. f. Door lock g. Provide Rj45 Patch Panel Suitable and 1m Long factory Made CAT6A patch cord (connection between Patch panel to Switch ) h. Earthing of the rack in the scope of the agency. If existing earthing is not available in the nearby area, the agency should make separate arrangements for the same, without any additional cost. 0_);0 each Excess(+) Full Conversion INR

416 Supply, installation, testing & commissioning of 98'' 4K UHD-LED professional display with brightness of 500 nit or better,Refresh rate 120 HZ, Native Resolution 3840 x 2160 (UHD), Contrast ratio 1200:1, Operation Hours (Hours/Day) 16/7 or better, HDMI IN(2.0) x 2, USB 2.0 X 2, 3.5mm Stereo audio Out x 1, RS232 x1, RJ45 x 1 & Speaker 40W 2ch mounted on wall with adjustable bracket at 45-60 degree (adjustable) with suitable mounting brackets as per instructions of EIC 0_);0 each Excess(+) Full Conversion INR

417 Supply, installation, testing & commissioning of 43'' 4K UHD-LED professional display with brightness of 500 nit or better, Native Resolution 3840 x 2160 (UHD), Contrast ratio 1200:1, Operation Hours (Hours/Day) 16/7 or better, HDMI IN(2.0) x 2, USB 2.0 X 2, 3.5mm Stereo audio Out x 1, RS232 x1, RJ45 x 1 & Speaker 10W 2channel output. Display shall be mounted on push pull wall mount and cost of same shall be included along with above LED display. 0_);0 each Excess(+) Full Conversion INR

418 Supply, installation, testing & commissioning of AVoIP Decoder supporting 4K60 4:2:0 resolution, HDR10 over 1G network, 1 HDMI output & 1 local HDMI input, Should have 1 balanced stereo audio output, 1 RS232, 1 IR, 2 USB type A connector, 2 Ethernet ports, Shall support (RTSP) real–time 4K60 4:2:0 video/audio/RS–232/IR/USB over standard 1G network. PoE powered, video encoding compression standard JPEG 2000, Enterprise IT–grade security — 802.1x and HTTPS/TLS, embedded web pages, P3K API commands via Ethernet, front panel navigation buttons, controllable via Web UI, API, command for third party control System shall support scalabiliy from one to many/many to many/video wall/KVM–over IP media distribution, video including required bulk audio-video (AV) cables such as speaker cables, microphone cables, control cables, shielded twisted pair(STP) cables, cat-6 cables, HDMI cables, USB cables, Video cables, PVC raceways, Flexible corrugated pipes, PVC conduits etc. alongwith necessary connectors for proper functioning of AV system, as per technical specification & as per instructions of EIC. 0_);0 Job Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Select, Excess (+), Less (-) Less (-)

Tender Inviting Authority: Chairman GB

Name of Work: Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

NIT No: DCSEM/CQD/QSB/25-26/NIT/75 dt.19.02.2026

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

500 PART - V : REBATE FOR TAKING AWAY (DEDUCT)

501 Rebate for taking out dismantled and other materials etc complete all as directed by the Engineer-In-Charge. The quoted rate shall include cost of mechanical transportation, loading, unloading, lead, lift, labour at all level & locations etc complete.

501.01 Old wooden material such as Furniture, Wall panelling, Frame & Shutters etc. 0_);0 kg Less(-) Full Conversion INR

501.02 Old structuarl steel members, GI Pipes etc. 0_);0 kg Less(-) Full Conversion INR

501.03 Old brass fittings such as taps, cock, showers and Gun Metal Gate Valves of various dia 0_);0 kg Less(-) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Please Enable Macros to View BoQ information

GOVERNMENT OF INDIA

DEPARTMENT OF ATOMIC ENERGY

DIRECTORATE OF CONSTRUCTION, SERVICES AND ESTATE MANAGEMENT

3rd floor, Vikram Sarabhai Bhavan, Anushaktinagar, Mumbai – 400 094 Telephone: (022) 25487324 / 25487323 Fax: (022) 2556 5362

TECHNICAL DATA SHEET

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

S. NO PARTICULARS DATA TO BE FILLED UP REMARKS

PART I : DETAIL OF THE AGENCY

I Name of the Agency Full name as per Regd. Cer.t

II Type of Firm Proprietoryship/ partnership/Limited Company/ any other

III Registration details with PWD/CPWD etc. Pl. furnish date of Registration and its validity

IV Yaer of establishment

V Postal address Pl indicate full postal Address with PIN

VI Contact with STD code

VII Fax with STD code

VIII Name of Contact person

PART II : DOCUMENTS TO BE SCANNED AND UPLOADED.

1 Financial Turn Over Certified by CA and also should have valid Unique Document Identification Number (UDIN) for the Practicing Chartered Accountant.

2020-2021 PL. FILL UP AMOUNT & UPLOAD SCANNED COPIES

Average of last 3 years

2 Profit & Loss Statement Certified by CA and also should have valid Unique Document Identification Number (UDIN) for the Practicing Chartered Accountant.

2020-2021 PL.FILL UP AMOUNT & UPLOAD SCANNED COPIES

3 Latest Bank Solvency Certificate. (should not be older than one year from the date of opening of tender.) PL. FILL UP AMOUNT, DATE & UPLOAD SCANNED COPY

4 List of Similar Works carried out in last 7 years i) Agency for whom exceuted ii) Value of Work iii)Stipulated and Actual time of Completion. PL. FILL UP DETAILS IN SEPARATE SHEET & UPLOAD SCANNED COPIES

3 similar works works a) PL. FILL UP THE AMOUNT & UPLOAD SCANNED COPY

2 similar works works a) PL. FILL UP THE AMOUNT & UPLOAD SCANNED COPY

1 similar works works PL.FILL UP AMOUNT AND UPLOAD SCAN NED COPY

5 Bidding Capacity PL.FILL UP AMOUNT AND UPLOAD SCAN COPY

6 List of all works in Hand indicating: i)Agency ii) Value of Work iii) Stipulated time of completion/ present position etc. PL. UPLOAD SCANNED COPIES

Typr of works executed since last seven years PL. UPLOAD SCANNED COPY

7 List of Construction Plants and Machinery. PL. UPLOAD SCANNED COPY

Maximum amount of single works executed since last 7 years PL. UPLOAD SCANNED COPY

8 List of Technical Staff. PL. UPLOAD SCANNED COPY

9 Certificates: (MANDATORY)

i) Registration Certificate if any PL. FILL UP REGD. NUMBER & UPLOAD SCANNED COPY

ii) Certificates of Work Experience /Performance certificates PL. FILL UP REGD. NUMBER & UPLOAD SCANNED COPY

iii) PAN (Permanent Account Number) PL.FILL UP PAN & UPLOAD SCANNED COPY

iv) Certificates of Registration for Goods and Services Tax (GST) PL. FILL UP REGD. NUMBER & UPLOAD SCANNED COPIES

v) EPFO registration certificate. PL. FILL UP REGD. NUMBER & UPLOAD SCANNED COPIES

vi) ESIC registration certificate.

vii) BOCW (Building and Other Construction Workers ) Welfare Board registration certificate or undertaking PL. FILL UP REGD. NUMBER & UPLOAD SCANNED COPIES

viii)Scanned copy of 'EMD' PL. UPLOAD SCANNED COPY

10 Undertaking that the eligible similar work(s) have not been executed through another contractor on back to back basis: PL. UPLOAD SCANNED COPY

11 UNDERTAKING as per Annexure III of Tender. PL. UPLOAD SCANNED COPY (MANDATORY)

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

DEPARTMENT OF ATOMIC ENERGY

DIRECTORATE OF CONSTRUCTION, SERVICES AND ESTATE MANAGEMENT

3rd floor, Vikram Sarabhai Bhavan, Anushaktinagar, Mumbai – 400 094 Telephone: (022) 25487324 / 25487305 Fax: (022) 2556 5362

Form "A" & "B" Financial Information & Bank Solvency

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

S. NO PARTICULARS REMARKS

I Name of the Agency

BELOW GIVEN DOCUMENTS TO BE SCANNED AND UPLOADED IN THE WEBSITE https://eprocure.gov.in/eprocure/app WITHIN THE PERIOD OF SUBMISSION SCAN COPY ATTACHED "YES" OR "NO"

1 Financial Turn Over Certified by CA Gross turnover Amount in lakh Profit/ Loss Amount in lakh Certified by Chartered Accountant

2 Latest Bank Solvency Certificate. (should not be older than one year from the date of opening of tender.)

3 Financial Arrangements for carrying out the proposed work

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

DEPARTMENT OF ATOMIC ENERGY

DIRECTORATE OF CONSTRUCTION, SERVICES AND ESTATE MANAGEMENT

3rd floor, Vikram Sarabhai Bhavan, Anushaktinagar, Mumbai – 400 094 Telephone: (022) 25487324 / 25487305 Fax: (022) 2556 5362

FORM C : Details of all similar works completed in all respect during the last seven years ending previous day of last date of submission of tenders.(Starting with latest work)

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

S. NO Name of the work/ Project and location Owner or sponsoring organisation Cost of work Rupees (in lakhs) Date of commencement as per contract Stipulated date of Completion Actual date of completion Litigation/ arbritation pending/ in progress (with details) Name & addresses/ Phone Nos of the officers to whom reference can be made. REMARKS

Name of the Agency

* Indicate gross amount claimed and amount awarded by the Arbitrator if any.

i) The agency may submit separate form for giving details of work (completed) for each year to fill up the details as above.

Separate sheets if any shall be numbered in sequence.

ii) The scanned copies of the work orders for each work be uploaded . BOQ shall be furnished at a later date on request.

iii) Certified that the above list of works is complete and no work has been left-out and the information given is correct to my

knowledge and belief.

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

DEPARTMENT OF ATOMIC ENERGY

DIRECTORATE OF CONSTRUCTION, SERVICES AND ESTATE MANAGEMENT

3rd floor, Vikram Sarabhai Bhavan, Anushaktinagar, Mumbai – 400 094 Telephone: (022) 25487324 / 25487305 Fax: (022) 2556 5362

FORM D : Details of all works of any nature under execution or awarded (No work shall be left out).

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

S. NO Name of the work/ Project and location Owner or sponsering organisation Cost of work Rupees (in lakhs) Date of commencement as per contract Stipulated date of Completion Upto date percentage progress of the work Slow progress, if any and reasons thereof. Name & addresses/ Phone Nos of the officers to whom reference can be made. REMARKS

Name of the Agency

i. The agency may submit separate form for giving details of each project (in progress/awarded) and fill up the details

as above. Separate sheets if any shall be numbered in sequence.

ii. The scanned copies of the work orders for each work be uploaded. BOQ shall be furnished at a later date on request.

iii. Certified that the above list of works is complete and no work has been left-out and the information given is correct

to my knowledge and belief

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

DEPARTMENT OF ATOMIC ENERGY

DIRECTORATE OF CONSTRUCTION, SERVICES AND ESTATE MANAGEMENT

3rd floor, Vikram Sarabhai Bhavan, Anushaktinagar, Mumbai – 400 094 Telephone: (022) 25487324 / 25487305 Fax: (022) 2556 5362

FORM E : Performance Reports of Works (Separate certificates for each work)

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

Name of the Agency

S. NO Name of the Work/ Project & Location Agreement No. Estimated Cost Tendered Cost Date of start Date of completion Amount of compensation levied for delayed completion, if any. Amount of reduced rated item, if any. Performance report REMARKS

(i) Stipulated date of Completion (ii) Actual Date of Completion (iii) Present position of the work, if in progress. (1) Quality of work (2) Financial soundness (3) Technical profiency (4) Resourcefulness (5) General behaviour (6) Time consciouness

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

DEPARTMENT OF ATOMIC ENERGY

DIRECTORATE OF CONSTRUCTION, SERVICES AND ESTATE MANAGEMENT

3rd floor, Vikram Sarabhai Bhavan, Anushaktinagar, Mumbai – 400 094 Telephone: (022) 25487324 / 25487305 Fax: (022) 2556 5362

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

FORM F: STRUCTURE AND ORGANISATION

1 Name & Postal Address of the applicant:

2 Telephone No./Telex No./Fax No.

3 Legal status of the applicant (Please tick and attach attested copies of original document defining the legal status)

(a) An individual; (b) A proprietary firm; (c) A firm in partnership (d) A limited company or Corporation

4 Particulars of registration with various Government bodies (scanned & uploaded photocopy) Sl.No. Dept/Organisation &Place of registration Registration No.

5 Names and Titles of Director & Officers with designation proposed to be concerned with this work

6 Designation of individuals authorised to act for the organisation

7 Was the agency ever required to suspend construction for a period of more than six months continuously after you commenced the construction? If so, give the name of the project and reasons of suspension of work.

8 Has the agency or any constituent partner in case of partnership firm, ever abandoned the awarded work before its completion? If so, give name of the project and reasons for abandonment.

9 Has the agency, or any constituent partner in case of partnership firm, ever been debarred / black listed for tendering in any organisation at any time? If so give details.

10 Has the agency, or any constituent partner in case of partnership firm , ever been convicted by a court of law? If so, give details.

11 In which fields of Engineering construction the applicant has specialisation and interest?

12 Any other information considered necessary but not included above.

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

Department of Atomic Energy

Dierctorate of Construction, Services & estate Management

3rd. Floor, Vikram Sarabhai Bahvan, Anushaktinagar, Mumnai- 400094

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

Form "G"- DETAILS OF TECHNICAL & ADMINISTRATIVE PERSONNEL TO BE EMPLOYED FOR THIS WORK

Name of the Agency

Sr. No Name Designation Qualifications Professional experience and details of work carried out How these would be involved in this work Remarks

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G, FORM H

GOVERNMENT OF INDIA

Department of Atomic Energy

Dierctorate of Construction, Services & estate Management

3rd. Floor, Vikram Sarabhai Bahvan, Anyshaktinagar, Mumnai- 400094

NIT No:- DCSEM/CQD/QSB/25-26/NIT/75 dt. 19.02.2026

Upgradation and Renovation of Dhruva Guest House including Civil, PH, Electrical and CCTV works at New Delhi.

Form H- DETAILS OF CONSTRUCTION PLANT AND EQUIPMENT LIKELY TO BE USED IN CARRYING OUT THIS WORK

Name of the Agency

Sr. No Name of Equipment/ Plant Nos Capacity or Type & make Age Condition Ownership status Current Location Remarks

Presently owned Leased To be purchased Proposed to be hired

1 Earth...moving

2 Equipment for hoisting

1. Building hoist

3 Equipment for concrete work

1.Concrete batching plant

2. Concrete Pump

3.Concrete Transit mixer

4.Concrete mixer

5. Needle Vibrator

8.Mortar mixing trough

4 Equipment for building work

1. Bar bending/ cutting machine

2. Steel shuttering

3. Polishing machines

4. Grinding / Polishing machines

5. Mechanical Rammer

5 Equipment for Road Works

2. Vibratory Road Roller

5 Equipment for transportation

1.Tipper / Dumper

3. Water Tanker

4. JCB / Poclain

6 Pneumatic equipment

1. Air compressors (Diesel)

2. Air compressors (Electrical)

7 Other equipments

1. Drilling machine

2. Welding generators

3. Welding transformers

8 Testing Equipment’s

1. Cube Testing

2. Sieve analysis

3. Ultrasonic test

5. Micron gauger

6. Moisture Metre

9 Any other plants/ equipments

NOTE: THE AGENCY MUST FILL UP ALL THE SHEETS VIZ.TECHNICAL DATA SHEET, FORM A AND B, FORM C,

FORM D, FORM E , FORM F , FORM G & FORM H.