SPECIAL REPAIR TO BLDG NO. P-68 OFFICER MD ACCN AT UDAIPUR MIL STN UNDER AGE (I) UDAIPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and as directed by the Engr-in-Charge.

Taking down wooden chowkats or frames area with shutter not exceeding 1.50 Sqm (without taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed by the Engr-in-Charge.

Taking down wooden chowkats or frames with shutter area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (without taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed by the Engr-in-Charge.

Taking down shutters of any description not exceeding 1.00 Sqm each, from chowkhat complete all as specified and as directed by the Engr-in-Charge.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, from chowkhat complete all as specified and as directed by the Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and as directed by the Engr-in-Charge.

M&L for 7 to 8mm thick Non skid joint free coloured ceramic tiles area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm laid over 15mm thick bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and as directed by the Engr-in-Charge.

M&L coloured glazed ceramic tiles in vertical surface size 450x350x7mm/ 600x300x7mm thick laid over 10mm thick rendering coat in CM 1:3, set and jointed in neat cement and pointed in white or coloured cement to match. The dado of same finish as of flooring shall be flush with plaster & all edges properly mitered complete all as specified and as directed by the Engr-in-Charge.

Material and Labour for double charge Vitrified ceramic coloured tiles 10 mm thick ( square or rectangular) polished, area of each tiles not exc. 0.36 sqm, in floors etc. set and jointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer with CM 1:6 complete all as specified and as directed by the Engr-in-Charge.

Material and Labour for double charge Vitrified ceramic coloured tiles 10 mm thick ( square or rectangular) polished, area of each tiles not exc. 0.36 sqm, in vertical surfaces etc. set and jointed in white or coloured cement to match over and including 10mm thick screed bed or bedding layer with CM 1:4 complete all as specified and as directed by the Engr-in-Charge.

Material & Labour for Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and as directed by the Engr-in-Charge.

M&L 18 to 20 mm thick Black granite stone in single piece in cooking plateform, slab for oval type WHB, sink / cills etc complete laid over 15mm thick rendering layer in CM 1:3 and jointed with white cement with admixture of pigment to match shade of granite stone including grinding and polishing complete and providing necessary holes for gas pipe / water supply pipe etc. complete all as specified and as directed by the Engr-in-Charge.

M&L for Vitrified out door tiles 40 cm x 40 cm x 10-12 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6 complete all as specified and as directed by the Engr-in-Charge.

Material & Labour for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore complete all as specified and as directed by the Engr-in-Charge.

S & F low level flusing cistern PVC 10 ltrs capacity with float valves (ISI Marked) white/lvory with inlet ball valve complete all as specified and as directed by the Engr-in-Charge.

Supply and Fix in repairs Vitreous China wash basin, flat back, size 550x400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets and vitreous china pedestal complete all as specified and as directed by the Engr-in-Charge.

S&F as in repairs of vitreous china clay water closet squatting pan ORISSA Pattern size 580x 440 mm white with integral foot rest incl 'P' or 'S' traps, flush pipe of 32mm dia HDPE pipe etc complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) & incl 01 No ‘P’ or ‘S’ trap of dia 100mm including provn of lime concrete bedding, complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repairs stainless steel sink with drainage board , of 1.00mm thick sheet for kitchen with plug,washers, waste pipe, CP waste coupling cast iron cantilever bracket of overall size 1145x510mm bowl size 560x410x250mm complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repairs stainless steel sink without drainage board, of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of overall sizesize 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repair stainless steel plate rack of 1.00mm thick sheet 900x900x200mm complete all as specified and as directed by the Engr-in-Charge.

S & F in repairs for Brass CP Sink Mixer with Swinging Casted Spout (Wall Mounted Model) for mixing hot & cold water with Connecting Legs & Wall Flanges, complete all as specified and as directed by the Engr-in-Charge.

S & F in repairs Brass CP single lever WHB mixer for mixing hot & cold water screwed down for iron/CPVC pipe and fixed with Connecting Legs & Wall Flanges, complete all as specified and as directed by the Engr-in-Charge.

S & F in repairs for Brass CP Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing in repair,long body bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and as directed by the Engr-in-Charge.

S&F in repair 15mm bore concealed stop/angle valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union complete all as specified and as directed by the Engr-in-Charge.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges complete all as specified and as directed by the Engr-in-Charge.

S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position after dismantling of old tank (water tank of cap exc 250 ltr and n.exc 500 ltr) and removing to store and complete all as specified and as directed by the Engr-in-Charge.

Supply and Fixing in repair rotational moulded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position after dismantling of old tank complete all as specified and as directed by the Engr-in-Charge.

S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed fixed complete all as specified and as directed by the Engr-in-Charge.

S&F in repair PTMT Float valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes complete all as specified and as directed by the Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and as directed by the Engr-in-Charge.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in a square n exc 0.5 Sq m in each pane complete all as specified and as directed by the Engr-in-Charge.

Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc. complete all as specified and as directed by the Engr-in-Charge.

All as item above but 20mm bore, complete all as specified and as directed by the Engr-in-Charge.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction complete all as specified and as directed by the Engr-in-Charge.

Material & Labour Steel Tubes 20mm bore, 'medium grade', galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed by the Engr-in-Charge.

Refixing of old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, etc. complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing stop valves, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed by the Engr-in-Charge. (Note : Weight of cock shall not be less than 0.575kg)

Supply and fixing angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed by the Engr-in-Charge. (Note : Weight of cock shall not be less than 0.575kg)

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repairs stainless steel grating openable 100mm dia with/without hole including fixing with white cement complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repair glass shelf assembly consisting of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed in repair CP brass soap tray fixed with brass screw complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing for mild steel framed work as in door chowkats/gate of angle or angle iron work as in fixing of cooler stand or gate by drilling/cutting the stone masonry wall and fixing up to 1st floor walls, other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing, 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings complete all as specified and as directed by the Engr-in-Charge. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

S&F factory single extruded WPC (Wood Polymer Composite) solid decorative type moulded door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and as directed by the Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

Supply and fixing IInd class (hollock) hard wood factory 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing, 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings complete all as specified and as directed by the Engr-in-Charge. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

S&F factory single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and as directed by the Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

Material & Labour for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in hold fast ,back of pressed steel chowkats complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed 150 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and as directed by the Engr-in-Charge.

S&F 100 mm long stainless steel butt hinges medium weight with galvanised MS hinge pin etc complete all as specified and as directed by the Engr-in-Charge.

S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and as directed by the Engr-in-Charge.

S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber complete all as specified and as directed by the Engr-in-Charge.

Supply & Fixed in repairs aluminium Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed MS helical door spring 300 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed steel windows box type ERW hollow 'P' section comprising double frame including gauged and glazed skelton shutter 30mm thick jointed internally with flat iron 25x3mm complete including hinges handle tower bolts, stops lugs,grill etc all as shown in drawing CEJZ TD -20 sheet 1/3 to 3/3 as applicablecomplete all as specified and as directed by the Engr-in-Charge. Note :- For the purpose of measurement & payment double shutter with frame and grill shall be considered as one unit. (ii) Glazing, wire mesh, guard bar & painting shall be measured & paid separately.

Supply & Fixing in repairs 18 mm thick prelaminated PVC celuka Ply prelaminated one side with decorative choice lamination and other side plain fixed with screw to PVC celuka ply works, complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed Continious piano hinges of mild steel bright finish or electro galvanized with width of flap (when open) 30mm complete all as specified and as directed by the Engr-in-Charge.

Supply & fixing in repair self closing/auto Casement type hinges 90/180 degree fixed to Modular Kitchen cabinets in Offrs Md Accn, complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed 75mm long Brass handle, cast type, polished bright fixed with nut and screws to cupboard shutter complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed magnetic ball catches with 8mm dia steel ball brass body and striking plate including letting in and fixed, complete all as specified and as directed by the Engr-in-Charge.

S&F of stainless steel wire cloth 0.36 mm nominal dia of wire & avg width of appertuer 1.40 mm fixed to Anodised aliminium framework of windows / vents & door shutters etc complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed Powder coated aluminium anodised window sliding type (3 shutter type) with sash bars, aluminium sections weighing 0.55 kg/m (min) including stainless steel wire mesh, necessary joining cleats, glazing clip, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as hinges, handles including anodised frame, including supply and fixing of 5 to 6 mm thick plain glass suitable for provn of centeral AC complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed Powder coated aluminium anodised ventilator fixed type ( partly glazed and partly gauged) with gasket, glazing clip etc weight of frame not less than 0.55 kg/rm and weight of shutter not less than 0.425 kg/rm complete all as specified and as directed by the Engr-in-Charge.

Supply & fixed steel for 4mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete all as specified and as directed by the Engr-in-Charge.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample including fancy finial caps (02 nos in each curtain rod) complete all as specified and as directed by the Engr-in-Charge.

Supply & fixing in repair of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample complete all as specified and as directed by the Engr-in-Charge.

Material & labour for fabrication of pressed steel cupboard shutter using 1mm thick MS plain sheet with frame 1.25mm thick bent to shape including two coat of synthetic enamel paint on internal surfaces & two coat of hammer tone finish on external surface alongwith locking arrangement mortice lock ,handle etc complete all as specified and as directed by the Engr-in-Charge as per drg No CEJZ/TD/12/2008 sheet 1/3 to 3/3.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified and as directed by the Engr-in-Charge.

Demolition cement concrete in any position complete all as specified and as directed by the Engr-in-Charge.

Material and Labour for PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including WPC as per manufacturers instructions to achieve the slop required, with minimum thickness of 25mm consolidated and finished even and fair without using extra cement. (WPC shall be measured and paid separately complete all as specified and as directed by the Engr-in-Charge.

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and as directed by the Engr-in-Charge.

M&L for providing Water Proofing Treatment to RCC Roof surfaces with APP Membrane in the following steps. (a) M&L for Rendering 10 mm thick on on fair faces of concrete surfaces as on PCC padding in CM 1:3 mixed with liquid water proofing compound as per manufacturer instruction and finish the surface even and smooth without using extra cement for laying APP membrane complete all as specified and as directed by the Engr-in-Charge. (Note :- water proofing compound shall be measured and paid sepretally) (b) M&L preparation of plastered surface of roof slab by throughly wire brushing washed dried up cleaned all foreign mater and dust and apply one coat of approved bituminous primer@ 0.40 ltr per sqm complete all as specified and as directed by the Engr-in-Charge. (c ) M&L for 3 mm thick APP modified polymeric membrane minimum weight 3kg/sqm and reinforced with non woven polyster reinforcement shall be laid by torch application method over a coat of bitumen S-35 grade C 30/40 applied @ 1.20 Kg/Sqm complete all as specified and as directed by the Engr-in-Charge. Note:-APP modified polymeric membrane shall all as specified. The side overlaps shall be minimum 75mm and end laps shall be minimum 100mm. All Overlaps shall be sealed as per manufacturer's instructions.

Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed by the Engr-in-Charge.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified and as directed by the Engr-in-Charge.

Material and Labour for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair,complete all as specified and as directed by the Engr-in-Charge. Note : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 mtr ht shall be included in the quoted rate).

Material and labour 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement complete all as specified and as directed by the Engr-in-Charge.

Supply only liquid water proofing compound, ISI marked complete all as specified and as directed by the Engr-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty, complete all as specified and as directed by the Engr-in-Charge.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of weather coat over a coat of 1 mm thick wall care putty for neat and smooth finishing complete all as specified and as directed by the Engr-in-Charge.

Material & Labour for preparing new plastered surfaces and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty on ceiling complete all as specified and as directed by the Engr-in-Charge.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and as directed by the Engr-in-Charge.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of weather coat over a coat of 1 mm thick wall care putty for neat and smooth finishing complete all as specified and as directed by the Engr-in-Charge.

Material and labour for preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper (acrylic) white on ceiling over a coat of 1 mm thick wall care putty complete all as specified and as directed by the Engr-in-Charge.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and as directed by the Engr-in-Charge.

M&L for preparation of old painted steel surface of any description, over 10cm in width or girth not other wise described and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engr-in-Charge.

M&L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and as directed by the Engr-in-Charge.

M&L for two coat of synthetic enamel painting to new steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and as directed by the Engr-in-Charge.

Supplying & laying 03 coats of reinforced acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slab with wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunken slab etc including repairing of loose/defective joints and applying 15mm thick plaster in CM 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and as directed by the Engr-in-Charge.

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and as directed by the Engr-in-Charge.

Material & labour for 100mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and as directed by the Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified and as directed by the Engr-in-Charge.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in cooking platform slab supported on wall, projected cupboard, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified and as directed by the Engr-in-Charge.

Material and labour for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in chajjas beams etc upto tripple storey bldgs including necessary formwork complete all as specified and as directed by the Engr-in-Charge.

Material and labour mild steel TMT bars, 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and as directed by the Engr-in-Charge.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out complete all as specified and as directed by the Engr-in-Charge.

S&F 110mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directed by the Engr-in-Charge.

S&F 110mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, fixed to wall complete all as specified and as directed by the Engr-in-Charge.

S&F 75mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directed by the Engr-in-Charge.

S&F 75mm dia UPVC (SWR) type 'B' pipe single sockets in any length with rubber ring joints, fixed to wall complete all as specified and as directed by the Engr-in-Charge.

S&F 110mm dia UPVC (SWR) bends any radius including cutting of holes complete all as specified and as directed by the Engr-in-Charge.

S&F 75mm dia UPVC (SWR) bends any radius including cutting of holes complete all as specified and as directed by the Engr-in-Charge.

S&F 110mm dia UPVC (SWR) branch piece single (single 'Y') equal or unequal complete all as specified and as directed by the Engr-in-Charge.

S&F 75mm dia UPVC (SWR) branch piece single (single 'Y') equal or unequal complete all as specified and as directed by the Engr-in-Charge.

S&F 75mm dia UPVC (SWR) floor trap, plain with grating including jointing with solvant cement complete all as specified and as directed by the Engr-in-Charge.

S&F 75mm dia UPVC (SWR) multi floor trap, with grating including jointing with solvant cement complete all as specified and as directed by the Engr-in-Charge.

S&F UPVC (SWR) gully trap 125/110 mm setting and jointing with solvant cement complete all as specified and as directed by the Engr-in-Charge.

M&L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate as in sub base complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing for machine pressed precast concrete coloured interlocking ( glossy finishing) paver blocks confirming to IS-15658-2006 of 60 mm thickness, M-35 grade as in hardstanding etc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified and as directed by the Engr-in-Charge.

Supply & Fixing in repair stainless steel 304 Grade kitchen rack, basket Trolley grill type or perforated type or wire type or any other type of approved complete all as specified and as directed by the Engr-in-Charge.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and good disturbed surfaces of walls, floors, etc. complete all as specified and as directed by the Engr-in-Charge.

M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed on stone/brick masonry wall surface with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified for the following controlled by one switch.

(a) One light point controlled by one switch with cables 1.5 sqmm size complete all as specified and as directed by the Engr-in-Charge.

(b) One fan/ exhaust fan point controlled by one switch with cables 1.5 sqmm size complete all as specified and as directed by the Engr-in-Charge.

(c) One 3 pin socket outlet, 5 amps on the same board with other switches, with cables 1.5 sqmm size complete all as specified and as directed by the Engr-in-Charge.

(d) One 3 Pin socket oulet 5Amps on indepndent, with cables 1.5 Sqmm size complete all as specified and as directed by the Engr-in-Charge.

(e) One light point controlled by two 2 - way switches, with cables 1.5 sq.mm size complete all as specified and as directed by the Engr-in-Charge.

(f) All as per item No. 124 above but for One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables1.5 sq.mm size complete all as specified and as directed by the Engr-in-Charge.

(g) All as per item No. 124 above but for One 3 Pin 15A pin socket oulet 15Amps on indepndent board or for geyser point with cables 2.5 Sqmm size complete all as specified and as directed by the Engr-in-Charge.

(h) All as per item No 124 above for AC point with PVC insulated unsheated FR cable, 1100 volt grade multy stranded copper conductor of size 4.00 sqmm indcluding earth wire PVC insulated unsheathed 100 volt grade cable with stranded copper conductor of size 4.00 sqmm ((Nominal area) common econnected to earth dolly controlled by one switch complete all as specified and as directed by the Engr-in-Charge.

S&F switch piano flush type single pole one way 5/6 Amps complete all as specified and as directed by the Engr-in-Charge.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

S&F socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

S&F of switch piano 15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

S&F socket outlet 2 in 1, 5 pin 5/6 Amps and 3 pin 15/16 Amps flush type including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

S&F ceiling rose surface type 3 terminals to be fixed on PVC block including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and as directed by the Engr-in-Charge.

S&F switch piano flush type single pole 16 Amp 2 way complete all as specified and as directed by the Engr-in-Charge.

S&F Bell multimusic type AC 230 volts, single pole complete all as specified and as directed by the Engr-in-Charge.

S&F Bell push, flush type, 5 amp complete all as specified and as directed by the Engr-in-Charge.

S&F LED integrated batten tube light fittings 20W 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by the Engr-in-Charge.

S&F LED lamp 9W system lumen (NOM) 600 with all accessories complete all as specified and as directed by the Engr-in-Charge.

M&L MCB TPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 415 Volts 4 way including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

M&L MCB SPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 200 amps rated 12 way including dismantling old one complete all as specified and as directed by the Engr-in-Charge.

S&F MCB TPN 63 Amps 415V 10KA 'B' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and as directed by the Engr-in-Charge.

S&F RCBOs Double pole, 30mA 32 Amp rating for earth leakage, overload & short-circuit protection complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing SPN 32-40 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing SP 6 to 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed by the Engr-in-Charge.

Taking down carefully, deposited to MES store and rehanging only ceiling fan & Exhaust Fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed by the Engr-in-Charge.

S&F exhaust fans AC single phase 240 Volts, 50Hz RPM 1200 & Copper winding of following size sweep of sturdy Engineering plastic complete with louvers shutter and complete accessories including hole with suitable size for Exhaust fan, after completer of work, finishing with cement and plastering and repainting with existing color complete all as specified and as directed by the Engr-in-Charge.

250 mm complete all as specified and as directed by the Engr-in-Charge.

300 mm complete all as specified and as directed by the Engr-in-Charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and as directed by the Engr-in-Charge.

S&F Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x2.5sqmm earth wire FRLS PVC insulated copper conductor, single core cable in surface/recessed as required complete all as specified and as directed by the Engr-in-Charge. Note : Two run of 2.5 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM.

S&F Submain wiring alongwith earth wire with the following sizes of 2x4.0 sqmm + 1x4.0 sqmm earth wire FRLS PVC insulated copper conductor, single core cable in surface/recessed as required complete all as specified and as directed by the Engr-in-Charge. Note : Two run of 4.0 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM.

S&F Submain wiring alongwith earth wire with the following sizes of 2x6.0 sqmm + 1x6.0 sqmm earth wire FRLS PVC insulated copper conductor, single core cable in surface/recessed as required complete all as specified and as directed by the Engr-in-Charge. Note : Two run of 6 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM.

Taking down old Sheet metal enclouser and supply and fix new sheet metal enclouser cubical type factory fabricated of 1.6 mm thick CRCA sheet with front side openable single door system powder coated painted to shade RAL 7032, PL Gasket, hinged single door ,IP-55 mounting plate of 2mm thick CRCA sheet steel and earth bolts etc. of size 600x500x200mm complete all as specified and as directed by the Engr-in-Charge. Note :-- Cost of any minor modification if required in fixing of the sheet metal enclouser as per site requirement and the disturbed surfaces matching with existing finish, will be deemed to be included in the cost of this item.

Supply & fixing sheet metal enclosures Single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20 Amps 240 Vlots complete all as specified and as directed by the Engr-in-Charge.

S&F LED security light luminaries of 35 watt for energy saving having IP-65 degree of protection of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED's should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 2.5 sqmm stranded copper conductor of suitable length complete all as specified and as directed by the Engr-in-Charge.

Taking down carefully, depostied to MES store and refix at the smae place electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25/50 litre as existing complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size to be fixed on roof surfaces with all fittings complete all as specified and as directed by the Engr-in-Charge.

SNEH CORPORATION (BID ID -3323341)

M/s Ajay kumar Garge (BID ID -3322478)

shree nathji trading corporation (BID ID -3316363)

chhaba construction (BID ID -3315057)