SPECIAL REPAIRS TO SWT QTY-04 AND BLDG NO P-96 TO P-103 AT AFS NARELA C/O AF STN RAJOKRI UNDER GE (AF) GURGAON

Amount

Demolition of unreinforced cement concrete in ground flooring and paving not exc. 15 cm thickness below or above ground level. Complete all as specified and directed

M&L for 75 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed

M&L for 40mm thick cement concrete type B-, 1:2:4 (20mm graded aggregate) as in flooring finished even and smooth without using extra cement complete all as specified

M&L for screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

M&L chequered cement concrete coloured tiles 30 cmx30 cmx25mm, set jointed and pointed in neat cement slurry in floors with grey cement and pigment complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate as in coping benching, gola and similar items all as specified

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and as directed

M&L for brick work with sub class 'B' brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and as directed

M&L 15mm thick plastering in CM 1:4 on brick or concrete surfaces finishing the surfaces even and fair without using extra cement complete all as specified

M&L Rendering 15 mm thick in CM 1:6 on brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as spd.

M & L applying two coats of Dr fixit Pidicrete URP on preparation of new surface of walls/floors complete all as specified and directed . Note : Water proofing coating mix URP , cement in the ratio 1: 1.5 by volume and work will be carried out as per manufacture instructions and approved dealer as specified

M&L 15mm thick plastering in CM 1:4 on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair without using extra cement complete all as specified

M&L rendering 10mm thick in CM 1:3 as in ceilings finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer paint complete all as specified and directed by Engr-In-Charge.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coat of cement base paint over a coat of primer complete all as specified

M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified

M&L for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing scrapping down smoke spot moulds moss and efflorescent salts and treating oily & greasy spots and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two coat of oil bound distemper on walls complete all as specified and as directed.

Complete all as per item No-18.00 here-in-before above but on surfaces of ceiling.

M&L for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing scrapping down smoke spot moulds moss and efflorescent salts and treating oily & greasy spots and filling of holes and cracks with with suitable material like cement or Crack seal etc and thereafter applying applying two coats of Cement base paint on walls complete all as specified and directed .

Dismantling of timber scantling in fillets, rails , rafters, purlins etc under 40 Sq cm in section incl wire mesh fixed in scantlings complete all as specifed

Taking down barbed wire fencing of any description and in any position fixed to RCC/steel posts complete all as specified and as directed by Engr-in-Charge (each row shall be measured separately)

S&FGalvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc comlete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise described complete all as specified and directed

S&F for rolled mild steel in framed work as in doors or steel gates of angle or other section with gusset plates, etc., drilled for fixing of steel sheeting or other covering to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe- 290.Gde-E-165 complete all as specified and directed.

S&F for framed work such as grills gratings, etc with ends of bar shouldered and/or revited or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings framework of water tanks and similar works confirming to Fe 290 Gde E-165 complete all as specified

S and F for Welded Steel wire Fabric wt per sqm n.exc 4 Kgs supplied and fixed complete to wood or steel members complete all as specified

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay) heavy for large gates, hook and pintle hinges large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

S&F Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes for notching of wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work etc complete all as specified and as directed

M&L for excavating in post holes (or similar holes) each n.exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25CM, in soft and loose soil complete all as specified

M&L cement concrete type B-2, 1:2:4 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

Taking down existing unserviceable water proofing treatment from roof slab including plaster and cleaning the roof slab by wire brush and removing the debries the premises of MD land complete all as specified and as directed.

Demolition of Mud phuska from roof, any thickness, including brick tiles, plastering and leeping (whether full thickness removed or only a part thereof) and cleaning the roof slab by wire brush and removing the debries from the site complete all as specified and as directed.

M&L for 15 mm thick plaster in CM (1:4) mixed with water proofing compound on roof slabs finished even and smooth without using extra cement after cleaning of roof surfaces with wire brushes complete all as specified and directed by Engr-in-Charge. Notes : WPC shall be measured and paid seperately

Supply only intergral water proofing compound ISI Marked complete all as specified and directed

M&L for 3mm thick APP modified prefabricated membrane in five layers & weight not less than 3.6 Kg/Sqm water proof membrane reinforced with non-wooven polyster without aluminium paint over top surface of water proofing membrane with 10cm longitudinal and horizontaling over lapping and joints finally thermo-fused with LPG flames laid over a tack coat of industrial bitumen grade 85/25 @1.20kg/sqm and preparing surface with a coat of bitumen primer @ 0.4 Kg / sqm as per manufacturer's instructions of APP modified membrane sheet complete all as spd and directed by Engr-in-Charge.

M&L, PCC 1:2:4 (using 12.5 mm graded aggregate) as in roof kerbs, rounded or chamfered On edges complete all as specified and as directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

Complete all as per item No. 39.00 here-in-before but exc 1.5 Sqm but not exc 4 Sqm each complete all as specified and as directed.

Taking down shutter of any description exc 1 Sqm and n.exc 2 Sqm and removing from site.

Taking down shutter of any description n.exc 1 Sqm and removing from site.

S&F 105X60mm girth pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified made out of 1.25mm thick MS Sheet complete all as specified and as directed.

S&F 125X60mm girth pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete as specified made out of 1.25mm thick MS Sheet complete all as specified and as directed.

M&L cement concrete Type B-0, 1:2:4 using 12.5mm graded stone aggregate as in filling of door frames of pressed steel and in bed blocks etc complete all as specified and as directed.

M&L prepration of new Steel surfaces of any description, not otherwise descri-bed, over 10cm width or girth & applying two coats of synthetic enamel paint complete all as specified

S&F factory made 35mm thick flush shutters solid core construction with block board core and plywood face pannel commercial type on both faces complete all as specified and as directed.

S&F factory made 35mm thick 2nd class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass, gauze, (without sash bars) edges for framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) fitted to chowkats complete all as specified and as directed.

S&F solid PVC door frame of size 50mm X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and drawing. Make:- Rajshri

S&F factory made PVC shelter panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified. Make:- Rajshri

S & F 75 mm Butt hinges, medium weight cold rolled, mild steel and fixed complete all as specified and as directed

S & F 100 mm Butt hinges, medium weight cold rolled, mild steel and fixed complete all as specified and as directed

S&F 100 mm size but hinges type C-21 extruded aluminium alloy with galvanised mild steel hing pin, anodised and fixed, complete all as specified and as directed

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section. Complete all as specified and as directed

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section. Complete all as specified and as directed

S & F 100 mm size extruded aluminium alloy handles cast type anodised and fixed.

S & F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed.

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified and as directed.

Dismantling boarding of any description , fixed in any position with nails complete all as specified and as directed.

S&F 25mm thick flush shutters, as in cupboard , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

S&F 18 to 19mm thick block board grade 2 quality interior grade decorative type with decorative face veneer on one face fixed with screws to timber framework as in shelves, drawers etc complete all as specified and as directed.

M&L preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coated and section of shutter 47x20mm mulion section 72x50mm (Based steel as per IS 513 "D" quality galanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of square bars powder coated fixed to window frame with screws including necessary fittings and all builders hardware such as handles, tower bolts and stays etc complete all as specified and as directed. Make : NCL type-4000 Series (Note : Glass and wiremesh shall be measured and paid separately under respective items)

M&L for 4.00 mm thick sheet glass ordinary quality and glazing each pane fixed with including neopune rubber gasket in aluminium frame work complete all as specified and directed.

S & F galvanised stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with necessary beading complete all as specified and as directed

M&L for gunniting work to RCC work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and S&F welded wire mesh fabric or wire net less than 95 X 95X 3 mm adhesive, plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 40 mm and making the surface even including 15mm thick plastering in CM 1:4 on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line and including necessary form work to be carried at upto single story building Note.- Where ever reinforcement required will be measured and paid seperatly etc complete all as specified and directed by Engr-in -charge.

M&L TMT bars 6mm to 8mm dia & over out to length, bent to shape required in column cranking bending spirally for hooping for & binding with & including MS wire (annealed) less than 0.9mm dia complete all as specified.

S&F in repair PVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & as directed.

Dismantling of existing water tanks of steel/PVC/AC of capacity exceeding 250 liters but not exceeding 500 litres complete all as specified and as directed.

S&F rotational mouldeddouble layer, polyethylene water storage tanks 500 ltrs capacity (cylinderical vertical with closed top) hoisted and fixed in position all as per SSR Part I complete all as specified and directed

S& Fixed in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm bore and fixed, minimum weight of float valve 210 gms complete all as specified and directed.

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 20 mm dia bore complete all as specified and as directed

S&F ISI marked medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F ISI marked tubes medium grade galvanized steel tube with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed

S & F in repair 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm.

S&F in repair vitreous china squatting pan “ORISSA” pattern size 580mm X 440mm, white with P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed.

S & F in repair 10 ltrs capacity PVC low level flushing cistern, ISI marked of make specified with inlet, float valve and handle including bracket with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F in repair fancy type Angle stop cock with flange, 15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&Fixed in repair vitreous china wash hand basin (flat back) of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector, including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F in pillar pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair bib taps, long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F as in repair aluminium anodised tubular towel rail 20mm dia, type D, 60cm long between flanges complete all as directed.

M&L for point wiring with PVC insulated and unsheathed cable 1.5 Sqmm (nominal area) ISI marked multi-stranded copper conductor single core FRLS grade including 20mm dia medium grade PVC conduit concealed in wall / false ceiling, concealed terminal boxes not less than 1.6 mm thick of required size with top cover 3mm thick of plastic laminated sheet (Hylum) of required colour complete metal flush terminal boxes with all accessories including 1.5 Sq mm PVC insulated and unsheathed stranded copper wire conductor FRLS grade cable to common earth and connecting to earth dolly including colour coding of cable shall be Phase - Red, Neutral- Black and Earth- Green complete all as specified and directed by Engr-in-charge for:-

One light /ceiling fan /Exhaust fan point controlled by one way switch 6 amps.

One bell point controlled by push button on the same board with other switches or independent board.

One 5 pin, 5 Amp switch socket out let on the same board with other switches.

One 5 pin, 5 Amp switch socket out let on the independent board.

M&L for point wiring with PVC insulated and unsheathed cable 2.5 Sqmm (Nominal area) stranded copper conductor single core including ISI marked FRLS grade 20 mm dia medium grade PVC conduit for point wiring, concealed in wall /, galvanised steel concealed terminal boxes not less than 1.6 mm thick of required size with top cover 3 mm thick of plastic laminated sheet (Hylum) of required colour with all accessories including 2.5 Sqmm PVC insulated and unsheathed stranded copper wire conductor FRLS grade cable to common earth and connecting to earth dolly for one 5 pin, 15 Amps switch socket out let point on an independent board including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green complete all as specified and directed by Engr-in-charge.

M&L switch piano flush type, 5 Amps, single pole, one way complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona or equivalent in approved makes.

M&L switch piano flush type, 15 Amps, single pole, one way complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona or equivalent in approved makes.

M&L socket outlet, flush type, 5 pin, 5 Amps, multipurpose complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona or equivalent in approved makes.

M&L socket outlet, flush type, 2 in 1, 3 pin, 5 and 15 Amps complete all as specified and directed by Engr-in-charge. Make : Anchor/ Cona or equivalent in approved makes.

S&F ceiling rose, surface bakelite, size as per relevant IS, three terminals complete all as specified and directed by Engr-in-charge. Make : Anchor / cona or equivalent in approved makes.

M&L for point wiring with PVC insulated and unsheathed cable 4.0 Sqmm (Nominal area) stranded copper conductor FRLS grade single core including ISI marked 20 mm dia medium grade PVC conduit for point wiring, concealed in wall /, galvanised steel concealed terminal boxes not less than 1.6 mm thick of required size with top cover 3 mm thick of plastic laminated sheet (Hylum) of required colour with all accessories including 4.0 Sqmm PVC insulated and unsheathed stranded copper wire conductor cable FRLS grade to common earth and connecting to earth dolly for one 5 pin, 15 Amps switch socket out let point on an independent board including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green complete all as specified and directed by Engr-in-charge.

S&F MCB DB sheet metal enclosure, double door, single pole and neutral 240V with 200 Amp rated bus bar suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 8 way complete all as specified and directed by Engr-in-charge. Make : L&T/Schneider/Legrand/Hager or equivalent in approved makes.

S&F in repair MCB, single pole & neutral, 240 Volts (16 to 40) Amps,10Ka complete all as specified and directed by Engr-in-charge. Make : L&T/ Schneider/Legrand(lexic)/Hager

S&F in repair MCB, single pole, 240 Volts (06 to 32) Amps,10Ka complete all as specified and directed by Engr-in-charge. Make : L&T/Schneider/ Legrand/Hager

S&F LED light retro type 1x8 watt,2 feet long surface mounted with accessories prewired including 1x8 watt LED tube connecting up with twin core twisted flexible copper conductor cable 0.5 sqmm including taking down old u/s light fitting of any type and size complete all as specified and directed by Engr-in-charge. Make : Havells cat part no LHFXCEP1TNNW020 or equivalent in approved makes.

S&F LED light fitting 1x18 watt,6500K ,4 feet long, surface mounted with accessories prewired including 1x18 watt LED tube connecting up with twin core twisted flexible copper conductor cable 0.5 sqmm including taking down old u/s light fitting of any type and size complete all as specified and directed by Engr-in-charge. Make : Havells cat part no LHEXBLP7UN1W018 or equivalent in approved makes.

M&L for wiring with two single core 6 sqmm stranded copper ISI marked conductor FRLS grade PVC insulated and unsheathed cable ISI marked drawn through 25 mm dia, medium grade, PVC conduit concealed in wall for sub main connection including 6 Sqmm PVC insulated unsheathed copper conductor ISI marked FRLS grade as Earth wire including taking down existing submain wiring incl conduit/casin capping with assecories complete all as specified and directed by Engr-in-charge.

S & F in replacement Meter Box 4 way , wall mounted , outdoor type weather and vermin proof (Protection Class IP-54) of size 700x700x150 mm and made out of 3.15 mm thick MS CRCA sheet with front hinged opening, rubber lining, locking arrangement ,powder coated comple .

Taking down of DB BOX /MCB DP /Single pole complete all as specified and directed by Engr-in-charge.

Taking down unserviceable aluminium/copper point wiring (light, fan, socket or power) incuding fixtures and fittings such as switcthes, ceiling rose, pendents, regulators, sockets etc for taking out of credit and making good complete all as specified and directed by Engr-in-charge.

Taking down of electric geyser ,storage type 230 volts single phase AC ,25/50 lts capacity and descaling of inner tank of geyser ,including brazing /welding if required ,re-assembling and refixing on site ,including preparation of surface of geyser and painting with 2 coat of white enamelled paint by spray painting machine complete all as specified and directed.

Taking down of Ceiling fan 1200/ 1400 mm sweep and refixing on site ,including cleaning & painting with 2 coat of white enamelled paint by spray painting machine complete all as specified and directed.

Taking down of Exhaust fan 300 mm sweep and refixing on site ,including cleaning & painting with 2 coat of grey enamelled paint by spray painting machine complete all as specified and directed.

Taking down of existing Energy Meters and refixing in the Meter box including making electrical connections , complete all as specified and directed.

S&F lamp holder, batten type PVC / polycarbonate type with back plate complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona or equivalent in approved makes.

S&F fan step regulator socket type complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona or equivalent in approved makes.

S&F bell push switch complete all as specified and directed by Engr-in-charge.Make:- Anchor/ cona or equivalent in approved makes.

S & F call bell multi music type, 230 volt all as specified and as directed.

Amount of Sch of Credit is Rs. 99,204.00.

JAIPAL AND BROTHERS

M/S LADPURIA ENTERPRISES

M/S GEETANJALI ENTERPRISES