PROVISION OF LED STREET LIGHT FITTINGS WITH POLE ALONG THE ROAD MH WELLINGTON TO VIA MANEKSHAW BRIDGE TO ASC SUP PL AND CONNECTED AREA OF WELLINGTON STN AND PROVISION OF RETROFITTED EMISSION CONTROL EQPT DEVICE RECD INCLUDING CONNECTED WORKS UNDER G

Amount

LED street light fitting 70 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

GI Pipe Medium Grade 40 mm bore bracket or suitable size for fixing LED Street light fittings, bent to shape of not less than 1.2m long with clamp made of GI flat Iron of size 32 x 6mm for street light fittings, duly painted with one coat of red oxide primer and two coats of aluminium based paint, fixed on poles with bolts, nuts and washers complete all as specified and directed.

Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 1.5 Sqmm, multistranded along with FRLS grade PVC insulated copper earth conduity conductor 1.5 Sqmm drawn through and including PVC conduit pipe 20mm dia with suitable clamps 02 Nos to fix steel tubular poles complete all as specified and directed.

Terminal box made of thermoplastic type out door type of size 260x210x116 mm for fixing on pole with and including of mild steel clamps with bolts and nuts, provn for cable entry for incoming and outgoing from bottom including MCB SP 6 Amps-01 No and 8 way connector with internal copper wiring connection duly fixed with and including cable glants threaded typemade of polymide with lock nut complete all as specified and directed. Make: Sintex or equivalent

GI Pipe light grade 40 mm dia for cable protection and including junction box to PCC coping (1mtr incoming + 1 mtr outgoing) complet all as specified and directed.

Steel tubular swaged poles of complete with cast iron base plate, finial taper, plug, bolts, nuts and screws as specified type 410 SP 22, 9 mtr long duly painted with one coat of red oxide primer and two coat of aluminium based paint complete all as specified and directed.

Plain cement concrete 1:4:8, type D-2 using 40 mm graded stone aggregate for street light pole bottom of pit for bed concrete (size 15cm height x 60cm x 60cm) complete all as specified and directed.

Plain cement concrete 1:3:6, type C-2 using 40 mm graded stone aggregate for street light pole (around the pole) concrete complete all as specified and directed.

Plain cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate for street light pole coping (Size 60cm x 60cm x 30cm) complete all as specified and directed.

XLPE insulated, armoured heavy duty electric cable with aluminium multi strands conductor, 1100 volts grade, cross-sectional area 16 Sqmm 2 core with stranded aluminium conductor complete all as specified and directed.

XLPE insulated, armoured heavy duty electric cable with aluminium multi strands conductor, 1100 volts grade, cross-sectional area 16 Sqmm 4 core with stranded aluminium conductor complete all as specified and directed.

3 Pole street light panel 12KW (Street light timer panel) contactor rating 65Amps 3 pole MCB TPN 63 Amps digital Timer with enclosures outdoor type complete all as specified and directed. Make : Havells Cat Part No IHTS09120

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth and getting out in soft /loose soil for laying for under ground cable all as specified and directed.

Cutting PCC/ road 200mm thick for laying of cable all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming using excavated soil in layers not exceeding 25cm thick complete all as specified and directed

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

Spreading (riddled earth soil) sand in trenches as cushioning to under ground cable on top and bottom of cable all as specified and as directed.

Supplying and laying un-reinforced precast concrete cable cover,Class LV, Type I, flat, size 250mm x 150mm x 40mm as protection to cable complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below the ground level with top edge of the plate not less than 1.5 mtr below the normal ground level connected to the galvanised iron earth strip 25mm x 4mm by means of bolts, nuts, hook nuts and washers of galvanised steel all as shown in electrical plate no 3 of SSR Part I connected to earthing testing point including earth and excavation work, PCC as directed, etc all as specified or indicated including testing on completion.

Supply, install in repair, testing and commissioning of factory made LT feeder pillar box, CPRI approved outdoor type 1.1KV made out of MS CRCA sheet 3mm thick, having 4 Nos Aluminium bus bar of 400 amps for phase 200 amps for neutral fixed on LT, 8 Nos insulators of size 0.60M x 0.45M with legs made out of MS angle 50x50x5mm & 0.75 mtr in length, locking arrangements front and back opening danger notice board with skull and bone monogram and indicating 1100 volt danger board including incoming and outgoing connections and testing on completion complete all as specified and directed.

LED Solar street light fitting 24 Watts including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and directed. Note: Excavation & earth work shall be measured separately. Make : Bajaj Cat Part No BSZSL-25W All in one standard or techno commercially equivalent in WIPRO/ PHILIPS

Supply, install, commissioning and testing of retrofitted emission control Eqpt/ Devices (RECD) into 200 KVA CPCB-I DG set installed at SS-1 so as to facilitate emission limit for Dg set already in use as per latest standard laid down by National Green Trubunal (NGT), Central Pollution Control Board (CPCB) Ministry of Environment and forest, GoI complete all as specified and directed. Make: Platino Automative Pvt Ltd / Vasthi Instruments/ Pee Kay Silent Generators/ PI Green Innovations Pvt Ltd or as approved by GE Note: (i) The complete work / Job of supply and installation & Commissioning of the Retrofit Emission Control Eqpt/ Device (RECD) has to be got executed by any firm/ company having type approval or having conformity of production verification compliance process out of the 05 agencies approved by the Nodal Agency Central Pollution Control Board (CPCB) necessary test certificates approvals etc in this regard has to be submitted to the Eng-in-charge at the time of sample approval. (ii) After satisfactory completion of the Job/ Work of installation and commissioning of the retrofitted emission control eqpt/ devices (RECD) the emission limits have to be tested from Govt/ NABL accredited lab & necessary test certificates etc in this regard have to be submitted to the Engr-in-charge & the cost of the same is deemed to be included in the unit quotes rates in the event of the report not found satisfactory w.r.t the stipulated Govt Standards, the subject RECD eqpt have to be replaced and retested till the result are satisfactory and as per the prevalant standards. (iii) Any item/ spare missed out in the technical specification, however essentially required for successful commissioning of the RECD eqpts is deemed to be included in the unit quoted rates. (iv) Contractor/ firm is required to visit the site of work for any doubts / clarification w,r.t specifications/ works involved etc. before quoting of the tender. Any clarification / query etc after conclusion of the contract shall not entertained and decision of the AO shall be final and binding. (v) The retrofit device shall confirm to the norms specified by CPCB. (vi) The efficiency of the device to reduce particulate matter shall be minimum 95%. (vii) The device shall have the characteristic of high heat resistance, good thermal conductivity, low exhaust resistance, high filtration efficiency, strong pressure resistance, good cold start performance, low ignition temperatures and high convertion efficiency. (viii) Working technology - As approved by CPCB. (ix) Optional reduction level of CO, HC and NOX shall be minimum 75%. (x) Material of construction shall be stainless steel 304. (xi) Working tempetature to reactivate regeneration -180 degree celsius. (xii) Digital display with temperature and pressure indicators. (xiii) Pollutant captured 2.5/ 10 (xiv) Product life shall be of minimum 10 years and one year warranty.

Manoprabha Electricals

Rajapriyaconstruction

POOJA ENGINEERING

P K ENTERPRISES

LUCKY ENTERPRISES

lakshmibuilders