PROVN OF COVERED SHED FOR PARKING VEH BEHIND BLDG NO. P 93, PROVN OF TOILET AND BATHROOM AT RONGMEN GATE AND SPL REPAIR OF 2 SWTS OF CAPACITY 250 KL AT UMROI MIL STATION UNDER GE UMROI

Amount

STN/LBW/05/2019-20 (Provn of covered shed for parking vehs behind bldg no. P-93)

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose Soil complete all as specified and directed

Excavation in trenches n. exc. 1.5 m wide and n.exc 1.5 m in depth for foundation or for shaft, well, cesspit, manhole, pier hole etc.n. exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Material and labour for plain Cement concrete Type D2, 1:4:8 mix, (40 mm graded aggregate) in foundations, filling and mass- concrete complete all as specified and directed.

Material & Labour for Pre-cast cement concrete block masonry with solid blocks, exceeding 10 cm in width and setting mortar, complete With C1 Type, 1:3:6 mix, (20 mm graded aggregate) set in cement mortar 1:6 Complete all as specified & directed

Material & Labour for Cement concrete in foundations, filling and mass- concrete Type B2, 1:2:4 mix, (40 mm graded aggregate). Complete all as specified & directed

Supply & fix Plate girder or single stanchions, built up of one beam or channel section with flang plates, caps, bases, splices angle brackets, cleats and other connections of rolled mild steel Fe - 410-W (Gde-E-250) quality "B", including painted one shop coat of zinc chromate primer paint including preparation of surface at Contractors workshop before fabrication complete all as specified & directed.

Supply & fix Rolled mild steel Fe - 410-W (Gde-E-250) quality "B"sections as in framing for cladding, flazing and the like fixed with angle cleats and connecting plates, etc. including painted one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop before fabrication complete all as specified and directed.

Supply & fix Rolled mild steel Fe - 410-W (Gde-E-250) quality "B"sections as in Roof trusses (framed ), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle,channel or flat sections) including distance pices,cleats etc. including painted one shop coat of zinc chromate primer paint (including preparation of surface) at contractors workshop before fabrication complete all as specified and directed.

Supply & Fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

Supply & Fix Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Material & Labour for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

Material & Labour for hardcore of brocken stone gauge n,exc 63mm deposited spreed and leveled in layers n. exc. 15cm thick water and rammed to true surfaces complete all as specified and directed.

Material & Labour for 100 mm thick cement concrete 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed.

Material & Labour for 100 mm thick cement concrete 1:2:4 type B1 using 20 mm graded aggregate as in flooring complete all as specified and directed.

Material & Labour for 50 mm thick cement concrete type C2, 1:3:6, using 40 mm graded aggregate as in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Material & Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces shall be done in two layers, 1st layer shall be of 10mm thick and 5mm thick 2nd layer mixed with water proofing compound @ 3% by weight of cement finishing the surfaces with fair and even without using extra cement complete all as specified and directed. Note: Integral water proofing compound shall be paid and measured separately.

Supply only integral water proofing compound ISI marked.

Material & Labour for Rendering 10mm thick in CM 1:6 on surface of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

Material & Labour for Three coats of white wash including preperation of newly plastered surface of walls complete all as specified and directed.

Material & Labour applying two coats of synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surface of girth exc 10cm width or girth complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n. exc. 25cm thick in any type of soil, all as specified and directed

Removing excavated soil not exc 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Supply and fix in repairs of MCB TPN DB 4 way for mounting SPN/SP/TPN/TP MCBs as incoming/outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DB shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process the steel sheet have to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43-IK 09 with metal door complete all as specified and directed.

Supply & fixing MCB SP 6 to 32 Amps 'B' Series 10 KA, 240 volts complete all as specified and directed.

Supply & fixing MCB SPN 40 Amps 'B' Series 10 KA, 240 volts complete all as specified and directed.

Material & Labour for sand cushioning to under ground cable using locally available fine clean dry river sand over,under ground UG cable laid in treches and gently punning to cushioning to cable complete all as directed. Note: Thickness of sand cushion after punning down will be measured and paid.

Material & Labour for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of size 230x150x40 mm to cover LT underground cables , laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed.

Supply, laying connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty) of size 10 sqmm 2 core, aluminium stranded conductor 1100 volts grade, laid through duct/ pipe / in trench etc. including cable glands & lugs complete all as specified and directed.

Supply and fixing ceiling rose surface PVC/Polycarbonate ISI marked, 65x50 mm two to three terminals complete all as specified and directed.

Supply and fixing LED fitting 1x18 watts including Tube rod, 230 Volts, bipin holders connector block etc.complete with all accessories internally pre-wired and including provision of PVC round block 7.5cm dia and 2 cm in depth (2 Nos) for mounting the fittings and electrically connecting with three single core 23x0.0076 PVC insulated multistranded copper conductor flexible cable from ceiling rose to light fitting, complete all as specified and directed. Make: : Bajaj Cat Part No BLRB- DB 118 for batten and Bajaj Tube rod No BLRB-18 Watt CWc or equivalent in specified make

Material & labour for Sub main wiring with two runs of single core 1.5 Sqmm (Nominal Area) FRLS PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC casing capping of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLS PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 1 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old sub main wiring connection to DBs/dolly shall be deemed to be included in this item and two run of 1.5sqmm as current carrying conductor and one run of 1 sqmm as earth conductor and PVC casing & caping shall be measured as one run complete all as specified and directed.

UMR/STN/REV/11/2019-20 Provn of toilet and bathroom eith water & electricity connection facility at Rongmen gate

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose Soil complete all as specified and directed

Excavation in trenches n. exc. 1.5 m wide and n.exc 1.5 m in depth for foundation or for shaft, well, cesspit, manhole, pier hole etc.n. exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Material & Labour for hardcore of brocken stone gauge n,exc 63mm deposited spreed and leveled in layers n. exc. 15cm thick water and rammed to true surfaces complete all as specified and directed.

Material and labour for plain Cement concrete Type D2, 1:4:8 mix, (40 mm graded aggregate) in foundations, filling and mass- concrete complete all as specified and directed.

Material & Labour for 25 mm thick cement concrete 1:2:4 type B0 using 12.5 mm graded aggregate as in flooring sub-base complete all as specified and directed.

Material & Labour for Pre-cast cement concrete block masonry with solid blocks, exceeding 10 cm in width and setting mortar, complete With C1 Type, 1:3:6 mix, (20 mm graded aggregate) set in cement mortar 1:6 Complete all as specified & directed

Material & Labour for Pre-cast cement concrete block masonry with solid blocks, not exceeding 10 cm in width and setting mortar, complete With C1 Type, 1:3:6 mix, (20 mm graded aggregate) set in cement mortar 1:4 Complete all as specified & directed

Material & Labour for 75 mm thick cement concrete 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed.

Material & Labour for Rendering 10mm thick in CM 1:6 on surface of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces shall be done in two layers, 1st layer shall be of 10mm thick and 5mm thick 2nd layer mixed with water proofing compound @ 3% by weight of cement finishing the surfaces with fair and even without using extra cement complete all as specified and directed. Note: Integral water proofing compound shall be paid and measured separately.

Supply only integral water proofing compound ISI marked.

Material & Labour for Rendering 5mm thick in CM 1:3 concrete ceiling surfaces, rendering is to be finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for Three coats of white wash including preperation of newly plastered surface of walls complete all as specified and directed.

Material & Labour for Two coats of colour wash over a coat of white wash including preperation of newly plastered wall surface complete all as specified and directed.

Material & Labour for Three coats of white wash including preperation of newly plastered ceiling surface complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n. exc. 25cm thick in any type of soil, all as specified and directed

Removing excavated soil not exc 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Material and labour for Damp proof course of 40 mm thick in cement concrete 1:2:4, type B-0( using 12.5 mm graded stone aggregate) to horizontal or vertical including necessary formwork and applying evenly a coat of blown type bitumen @1.5kg per Sqm and binding with dry sand @ 0.5Cum per Sqm complete all as specified and directed .

Material & Labour for reinforced Cement Concrete (nominal mix) Type B1, 1:2:4 (20 mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material & Labour for reinforced Cement Concrete Type B1, 1:2:4 (20 mm graded aggregate) as in beams, lintels complete all as specified and directed.

Use and waste of Formwork rough finished to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)complete all as specified and directed.

Use & waste of Formwork rough finished to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, also splays between floors and beams, complete all as specified and directed.

Supply & Fix TMT bars 10mm dia and above cut to length bent to shape required including cranking, bending spirally for hooping, hooling ends and binding with mild steel wire (annealed) not less than 0.9mm dia , complete all as specified and as directed.

All as per Sr. Item No. 3.23 here in above but 6 mm to 8mm dia of bar.

All as per Sr. Item No. 3.23 here in above but 5 mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

Supplied and fixed Steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed.

Supply and fix 3mm thick figured glass, pin headed type and glazing with oil putty or aluminium glazing clip in square n exc 0.5 sq. m in each complete all as specified and directed.

Material & Labour applying two coats of synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surface of girth exc 10cm width or girth complete all as specified and as directed.

Supply and fix aluminum anodised barrel tower bolt ISI marked 150mm long of extructed section all as specified and as directed.

Supply and fix aluminum anodised handle cast type ISI marked 150 mm, anodised all as specified and as directed.

Supply and fix butt hinges 100 mm long extruded aluminium alloy ISI marked with galvanised mild steel hing pin type B-21 as specified and as directed.

Material & Labour for 15 mm thick Screed bed or bedding layer of cement mortar 1:6, laying for floor finishes complete all as specified and directed.

Supply & Fix Non - skid Ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Supply & Fix Glazed ceramic tiles in vertical surface 350x250x 7 mm/450 x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Supply & Fix Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

Supply & Fix Wash basins, Vitreous China (flat back or angle back type) of size 630 x 450 mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Supply and fix Pillar taps of 15mm , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe.

Supply & Fix Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for fixing supply pipe to flushing discharge pipe (Exclusive of cistern, trap and waste pipe) complete all as specified and directed

Supply & Fix 10ltr capacity Low level PVC valveless, syphonic action type fluslhing cistern, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply & Fix CP Bib taps 15mm, fancy type, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply & Fix CP Stop valves 15mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions.

Supply & Fix PVC connection 15 MM size with PTMT nuts of length 450MM complete all as specified and directed.

Supply & Fixing Tubes medium grade(ISI marked), 20mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors Complete all as specified and directed.

Supply & Fixing Tubes medium grade (ISI marked), 15mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors Complete all as specified and directed.

Supply & Fix 500 ltr Rotational moulded polyethylene water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Supply & Fix Ball brass valves (ISI marked) of 20 mm bore, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as directed.

Supply & Fix Gun-metal, globe or gate valves (ISI Marked) for iron pipe 20mm bore with iron wheel head, screwed both ends complete all as specified and directed.

Supply & Fix PVC (SWR) pipes ISI Marked 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply & Fix PVC (SWR) pipes ISI Marked 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply & Fix PVC (SWR) bends ISI marked 110 mm bore any radius complete all as specified and directed.

Supply & Fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening complete all as specified and directed.

Supply & fix Factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with particle board with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC sheet Polyurethane paintedonthe front face and 2 mm prelam PVC sheet on back face in frame at site as specified and directed.

Supply & fix 40 mm Low Density Polyethylene pipes (LDPE) of pressure rating 6 Kgf/Cm2 fixed complete to wall ceiling or in floors complete all as specified and as directed.

Supply & Fix Grating doom 100mm dia of PTMT (Minimum weight 25gms).

Supply & Fix PTMT tubular Towel Rail 600mm long and 20 mm dia fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as directed.

Material and labour for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate for foundation filling and mass concrete all as specified and directed by Engineer-in-Charge.

Material & Labour precast RCC 1:2:4, type B1 using 20mm graded aggregate as in drain cover slab supported on walls, desk slabs and shelves including necessary formwork, complete all as specified as directed.

Material & Labour Rendering 15mm thick in CM 1:3 on fair faces of block masonry or concrete surfaces mixing with water proofing compound as per manufacturer instructions, rendering is to be finished even and smooth without using extra cement, complete all as specified and as directed. Note: WPC shall be measured and paid for seperately under relevent item of this Schedule.

Material & Labour Cement concrete 1:2:4, type B0, using 12.50mm graded crushed stone aggregate in coping, benching, haunching, kerbs water troughs, platform over roof slab for instalation of PVC water tank and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified as directed.

Material & Labour Salt-glazed stone ware drain pipes 150mm bore (dia) Grade A, laid in trenches and jointed in cement mortar 1:1, Testing after laid and jointed complete all as specified and as directed.

Material & Labour Concrete 1:3:6 (40mm graded aggregate) as in bed to drain pipes 150mm bore (dia) including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and as directed.

Material & Labour for cutting holes in existing manholes or septic tank for connecting new drains and making good dismanteled portion in by carrying out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 as required all as specified and as directed.

REV E&M

Material and labour for point wiring for One light/fan point controlled by one way switch with 1.5 Sqmm single core, PVC FRLS insulated unsheathed, multistranded copper conductor drawn through and including PVC casing and caping/ PVC conduit pipe including necessary accessories like bends, tees PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLS insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of suitable sizes with plastic laminated white/coloured top sheet cover 3 mm thick complete all as specified and directed

All as per Sr. Item No. 4.01 here in before but for One 3 Pin 5 Amps socket outlet point on same board.

All as per Sr. Item No. 4.01 here in before but using 2.5 sqmm PVC FRLS insulated copper condutor wire for connecting 15A socket on independent board.

Supply and fixing of switch piano flush type ISI marked 240 Volts 5 Amps, SP, one way complete all as specifed and directed.

Supply and fixing of socket outlet 3 Pin, 5 Amps, 240 volts flush type (non shuttered) ISI marked complete all as specified/ directed.

Supply and fixing switch socket out let combination multipurpose 5 pin, 15/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) ISI marked complete all as specified/directed.

Supply and fixing ceiling rose surface PVC/Polycarbonate ISI marked, 65x50 mm two to three terminals complete all as specified and directed.

Supply and fixing LED fitting 1x18 watts including Tube rod, 230 Volts, bipin holders connector block etc.complete with all accessories internally pre-wired and including provision of PVC round block 7.5cm dia and 2 cm in depth (2 Nos) for mounting the fittings and electrically connecting with three single core 23x0.0076 PVC insulated multistranded copper conductor flexible cable from ceiling rose to light fitting, complete all as specified and directed. Make: : Bajaj Cat Part No BLRB- DB 118 for batten and Bajaj Tube rod No BLRB-18 Watt CWc or equivalent in specified make

Supply and fix in repairs of MCB SPN DB 4 way for mounting SPN/SP MCBs as incoming/outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DB shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process the steel sheet have to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43-IK 09 with metal door complete all as specified and directed.

Supply & fixing MCB SPN 40 Amps 'B' Series 10 KA, 240 volts complete all as specified and directed.

Supply & fixing MCB SP 6 to 32 Amps 'B' Series 10 KA, 240 volts complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary excavation and earth works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and directed.

Supply and fixing Bulb holder angular PVC/Polycarbonate ISI marked suitable for batten fittings including one no. LED lamp of 9W complete all as directed.

Cutting hole for 200mm sweep exhaust fan, necessary plastering including grouting with 04 Nos 100mm long 12mm dia stud bolt, fair finishes of wall surface including colour wash matching with as per existing complete all as specified and as directed.

Supply and fix exhaust fans AC single phase 230/240 V of size 300 mm sweep plastic body with louver complete all as specified and directed. Note: Quoted rate shall be deemed to be included of accessories required for fixing and making good disturbed surfaces.

Supply, installation, testing & commissioning of heater water storage type electric geyser (vertical cylindrical type) 25 litre capacity with BEE 5 star rating (minimum) and ABS body, porcelain enamel glass lined inner tank including fixing arrangement with providing including suitable capacity flexible cable 3 core with 3-pin plug of 16 amp capacity maximum 2 mtr length, PVC connection pipe of size 15 mm dia and 450mm length for Hot Cold water, including chromium plated brass nuts and fixing on walls with and including all necessary fitting material i.e. Mild steel Bolts (Bolts to be grouted), CP brass nuts, Washers, etc complete all as specified and as directed. Make: Havells Monza EC or equivalent in specified make

STN/SR BLDG/UMR/10/2019-20 Spl repairs of 2 SWTS capacity 250 KL at FASF

Roughning surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust including applying cement slurry @ 3 kg/Sqm complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls etc. Including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

Material and labour for Reinforced cement concrete design Mix M-30 using 20mm graded aggrerate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and labour for Reinforced cement concrete design mix M-30 using 20 mm graded aggregate as in Walls, retaining walls, basement walls, ballast walls and the like any thickness above top of footing including attached pilasters and buttresses complete all as specified and directed.

Material & Labour Rendering 5mm thick in CM 1:3 on fair faces of block masonry or concrete surfaces mixing with water proofing compound as per manufacturer instructions, rendering is to be finished even and smooth without using extra cement, complete all as specified and as directed. Note: WPC shall be measured and paid for seperately under relevent item of this Schedule.

Material & Labour Rendering 15mm thick in CM 1:3 on fair faces of block masonry or concrete surfaces mixing with water proofing compound as per manufacturer instructions, rendering is to be finished even and smooth without using extra cement, complete all as specified and as directed. Note: WPC shall be measured and paid for seperately under relevent item of this Schedule.

Material & Labour Rendering 15mm thick in CM 1:3 on fair faces of block masonry or concrete surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

Supply only integral water proofing compound ISI marked.

Material & Labour for 75 mm thick cement concrete type C2, 1:3:6, using 40 mm graded aggregate as in plinth protection, finishing cement concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and directed.

Supply and fix steel wire fabric of wt n exc 4 Kg per Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples fixed complete to wood or steel members complete all as specified and directed.

Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and similar work including attached pillasters, buttresses, etc; vertical or batter for fair finished surfaces, complete all as specified and directed.

Material & Labour for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

Forming construction dummy joint 65mm deep x 10mm wide, filled with sealing compound complete all as specified & directed.

M/s Jaiswal and Co

MOINUL HOQUE CHOUDHURY

S K TRADERS