SPECIAL REPAIR REPLACEMENT OF CIDI PIPELINE AND SPECIAL REPAIR REPLACEMENT OF BER CHLORONOME PLANT IN DOMESTIC AREA AT AF STATION GWALIOR

Amount

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep in any type of soil including forming sides and bottom surface to required levels/slops/gradients etc. complete all as specified and directed at site. Note: The disturbed surfaces of roads/paths/plinth shall be made good to match with the existing surfaces and is deemed to be included in unit rate quoted.

Returning, filling in, excavated soil including leveling, watering and well ramming in layers of thickness not exceeding 25 cm in each layer complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing the soil where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. and segregation serviceable bricks, keep them staking for re use complete all as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 etc,complete all as specified.

Disconnecting and taking up or down old existing steel tubing and connections of any description/ grade and in any position in trenches/under floors / on walls etc including connected fittings/accessories and fixtures like union,valves etc. seggregation serviceable pipes and fittings, keep them safe custody for reuse and unserviceable material be removed from site of work all as directed and specified for the following sizes :-

50 mm bore

40 mm bore

25 mm bore

20 mm bore Note: Earth work, returning filling, removing shall be measured & paid separately under respective item.

Supply /Laying / jointing and testing in trenches/wall/floor galvanized iron water tubing medium grade including necessary new steel fittings / accessories ISI Marked complete all as specified and directed for the following sizes. [Make: Tata/Jindal/TT swastik]

50 mm bore

40 mm bore

25 mm bore

20 mm bore

Disconnecting & taking up/down existing, cast iron pipe lines / water mains of any description / grade and in position including fittings, accessories and fixtures etc existing in between pipe line, by taking out and opening any type of joints (Tyton /Gasket / Lead joints) complete all as specified and directed by the Engineer-in-Charge for following bore of pipes:- Note:-Earthwork, returning filling and removal shall be measured and paid separately under relevant item.

300mm bore

200mm bore

150mm bore

100mm bore

80mm bore Note:- Old CI pipe / fittings retrieved in serviceable condition from taking down shall be reused in the work as approved by the Engineer-in-Charge.

Supplying ,laying, jointing & testing in trenches ductile iron pipes with spigot and socketed ends class k9, conforming to IS 8392-2000 and suitable for push on joints, standard bituminous finish layer not less than 70 micron, cement lining complete all as specified and directed by Engineer-in-Charge for the following size:- Note :-(i) Earth work, Joints and DI specials/fittings of the pipes shall be measured and paid for separately under appropriate item of Schedule `A' (ii) Joints of the pipes shall be measured and paid for separately under appropriate item of Schedule `A'. [Make: TATA/Electrosteel casing Ltd./Jindal]

300mm bore

200mm bore

150mm bore

100mm bore

80mm bore

Material and labour for cast iron/ductile iron specials/fittings such as bend, tee, socket, collar Reducer, Tail Pieces etc. suitable for spigot and socketed/ flanged end pipe of up to 150 mm bore complete all as specified and directed. [Make: Upadhay/Kirlosker /Leader/Kalinga]

Material and labour for cast iron/ductile iron specials/fittings such as bend, tee, socket, collar Reducer, Tail Pieces etc. suitable for spigot and socketed/ flanged end pipe of 200mm to 300 mm bore complete all as specified and directed. [Make: Upadhay/Kirlosker /Leader/Kalinga]

Taking down existing gun metal gate valves of any description and in any position, complete all as specified and directed the following sizes :-

50mm bore

40mm bore

25mm bore

20mm bore

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve with iron wheel head, both ends screwed for iron pipe complete all as specified and directed for following bore of pipes [Make:-Zoloto/Leader/Kirlosker]

50mm bore

40mm bore

25mm bore

20mm bore

Taking up or down existing old cast iron sluice valves of any description and in any position, including taking out joints complete all as specified and directed for the following sizes :-

300 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

Supply, installation, fixing, jointing and testing, ISI Marked, of approved quality, cast iron sluice valve of class PN-1.6 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, long body type, jointed and tested complete all as specified and directed for following bores :-

300 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore [Note:- (i) Joints of the sluice valve shall be measured and paid for separately under appropriate item of Schedule `A' . (ii) Sluice valve shall be of MAke- Zoloto/Leader /Kirlosker/IVC]

Burring out run lead joints for the following sizes of CI pipes/fittings etc all as specified and directed:-

300mm bore

200mm bore

150mm bore

100mm bore

80mm bore

Material and labour for run lead joints including caulking properly for the following sizes of CI pipes/fittings etc all as specified and directed:-

300mm bore

200mm bore

150mm bore

100mm bore

80mm bore

Dismantling joints in flanged end cast iron pipes and fittings complete all as specified and directed for following sizes:-

300 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

Material and labour for rubber/fibre gasket joints complete with and including minimum 3 mm thick rubber/fibre gasket and necessary nuts/bolts/washers all as specified and directed for following sizes:-

300 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

Material and labour for rubber gasket joints (Tyton joints) for ductile iron pipes and fittings complete with necessary nuts/bolts/washers all as specified and directed for following sizes:-

300 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

Cutting of the existing CI pipe line for rectifying leakage and reducing to required length, in position, for insertion of collars or other fittings including dewatering etc complete all as directed for the following bore of pipes:-

(a) CI Pipe line 300 mm bore

(b) CI pipe line 200 mm bore

(c) CI Pipe line 150 mm bore

(d) CI Pipe line 100 mm bore

(e) CI Pipe line 80 mm bore

Material and labour for construction of brick masonry valve pit /chamber complete with 3mm thick MS sheet cover fixed on MS angle of size 40x40x5mm duly painted with two coats of black synthetic enamelled paint over a coat of red oxide primer with locking arrangement of size 450x 450x 600mm (depth) (internal dimensions) as shown on Drg No CWE/TD/129 sheet No 1/1 dt 18.12.87 with and including necessary excavation & earth work in any type of soil including Dismantling & breaking down the old existing valve pit chamber of any size and any shape and remove material from site of work complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 22 here-in-before but of size of valve pit 600mm x 600mm x 600mm (depth) (internal dimensions)

All as per srl item No 22 here-in-before but of size of valve pit 800mm x 800mm x 900mm (depth) (internal dimensions)

Supply, installation, testing & commissioning of gnanular chlorination dosing pump, high pressure, single head, gear motored adjustable dosing pump having output of 2 US GPD to 40 US GPD and adjustable high pressure of upto 100 PSI (7KG/CM)2 with accessories including lead, tubing, connection nuts, injection check valve, clay weight and ferrules with all connected accessories including necessary pumping connections from dosing plant to chlorination point as per OEM recommendations and necessary electric point wiring where ever required to run dosing plant complete all as directed by Engineer in charge : Make : DECLIBAC TECHNOLOGIES / POTTER & WATTS CORP / BRIOZING UNLIMITED.

Supply, installation, testing & commissioning of dozing system non metallic solution tank of 100 ltrs capacity along with lid & level gauge with motor driven agitator to maintain uniform solution through out the tank with all connected accessories complete all as directed by Engineer in charge. Necessary arrangement at site will provide by the contractor. Voltage input 230V, single phase, 50HZ, suitable for 900 rmp capacity : Note : -applicable as submersible pumps / centrifugal pumps and UGR Make : DECLIBAC TECHNOLOGIES / POTTER & WATTS CORP / BRIOZING UNLIMITED.

M/s KKPARASHAR

SHRI RAM CONSTRUCTION

ISHWAR ENTERPRISES

SHOURYA ENGINEERING ENTERPRISES

M/S DHARMENDRA SINGH TOMAR

YASH DEVELOPERS AND CONSTRUCTION COMPANY

m/s vikash Engineers

M/s Pal Construction

Bidder Name

SHRI RAM CONSTRUCTION