CA NO CWE/CHD-31/2020-21 RENEWAL OF FURNITURE AGAINST SURVEYED OFF ITEMS UNDER GE CHANDIGARH

Amount

PART-I WOODEN FURNITURE Chair Easy (FD-281), all as per drawing and as make approved by GE.

Peg Table (FD-277) Ist class seasoned teak wood shall be used through out. Top shall be made out of pre-laminated particle board 18/19 mm thick ISI marked exterior gde. 6 mm thick teak wood beading shall be used all around at top. Rubber PVC shoes shall be provided at the bottom of legs duly screwed. All wood surfaces shall be French polished to a glossy finish. Rest all as per drg complete all as shown as Drg No FD-277 complete all as specified and directed.

Table Writing Medium (FD-275), all as per drawing and as make approved by GE.

Table Dining 6 pers (FD/E6/MAP-11/03), all as per drawing and as make approved by GE.

Chair Dining FD-279, all as per drawing and as make approved by GE.

Teapoy Wooden FD-232, all as per drawing and as make approved by GE.

Table Centre (FD-274), all as per drawing and as make approved by GE.

Chair Dining Cushioned (FD/E6/MAP/10 (R)) (a) All wood work shall be of 1st class hard wood (Teak). (b) Seat shall be 75 MM thick foam of 32 density covered with good quality tapestry cloth (cost of cloth not less than Rs 450/- per meter) as approved by GE over 12MM thick commercial plywood as per IS-303. (c) Nylon buffers of appropriate size shall be screwed to the bottom of each leg. (d) All exposed surfaces of timber and plywood shall be french polished. (e) All joint fixing shall be done in accordance with standard workmanship and specification. (f) Rest all as shown on drawing.

Hat Stand with Mirror FD-362 DIMENSION:Overall size shall be 1330 mm long, 710mm high. DESCRIPTION:The inner frame shall be of 50mmx20mm teak wood battens six in nos .The back and front of frame shall be covered with 6mm thick commercial ply.The edges of the frame shall be covered with 6mmx35mm teak wood edging fixed alround the frame with headless nails and adhesive.Six brass pegs 120mm long shall be fixed over the wooden membrane with brass screws as shown in drg.5mm thick looking mirror of (saint gobian,Modiguard/Atul) shall be provided as shown on drg with beading alround . Mild steel key plate shall be provided at both top corners of the hat stand. FINISH: All teak wood surfaces shall be given high gloss French polish with lacquer finish. All steel surfaces shall be painted with two coats of enamel paint over a coat of primer. Rest all as per drgs.

Sofa Set 5 Seater with Cushioned (FD 281), all as per drawing and as make approved by GE.

Table Dessing Ladies with Mirror (FD-251), all as per drawing and as make approved by GE.

PART-II STEEL FURNITURE Chair Verandah (FD-359) all as per drawing and as make approved by GE.

Table computer 900 x 600 x 750mm (FD/E6/MAP/03), all as per drawing and as make approved by GE.

Almirah Large Steel with Shelves (FD-1031). (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1 mm thick mild steel sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. 4 lever brass lock 65 mm size shall be provided as per Godrej pattern, of make GODREJ, LINK, HARRISON. (iv) Almirah shall be provided with three numbers adjustable shelves with four compartments (v) One steel chrominium plated handle shall be provided to the drawer. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamel paint (olive green) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint. (viii) Rest all as shown on drawing.

Table steel 900 x 600 x 760mm with drawer (FD 1008). DIMENSION;Overall size shall be 900mmx600mmx 760mm. DESCRIPTION:Steel frame shall be of 800mmx500 x742mm.Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm.Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm top rails on long and short sides. Two short stiffeners joining legs in short sides at 100mm from bottom of legs shall be provided with 25mm square mild steel tube of wall thickness 1.6mm .One long stiffener shall be provided in the middle of short stiffener joining short stiffeners with 25mm square mild steel tube of wall thickness 1.6mm at 100mm from bottom of legs. A drawer on left side of table near top stiffener shall be provided of size 350mmx130mm and 500mm deep with locking arrangement and recessed handle. Mild steel sheet used for drawers shall be of 1mm thickness.Top of table shall be of 18 mm thick pre-laminated particle board of walnut shade and 4mm teak wood edging al -round the top of table. PVC/Hard rubber toes shall be provided to the bottom of legs. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Shoe Rack Steel (FD/E6/MAP/02(R)), all as per drawing and as make approved by GE.

Chair CBA Cushioned (HFD -2041), all as per drawing and as make approved by GE.

Table Office (Officers) steel FD-1003, all as per drawing and as make approved by GE.

Charpoy IP Folding Ply Wood Top (FD-1119), all as per drawing and as make approved by GE.

Table Dining ORs steel FD 165(R), all as per drawing and as make approved by GE.

Table Steel 900 x 600 x 760 mm without drawers (FD-1007) DIMENSION;Overall size shall be 900mmx600mmx 760mm. DESCRIPTION:Steel frame shall be of 800mmx500 x742mm.Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm.Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm top rails on long and short sides. Two short stiffeners joining legs in short sides at 100mm from bottom of legs shall be provided with 25mm square mild steel tube of wall thickness 1.6mm. One long stiffener shall be provided in the middle of short stiffener joining short stiffeners with 25mm square mild steel tube of wall thickness 1.6mm at 100mm from bottom of legs. Top of table shall be of 18 mm thick pre-laminated particle board of walnut shade and 4mm teak wood edging al -round the top of table. PVC/Hard rubber toes shall be provided to the bottom of legs. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Chair School with hand Board (FD/F6/MAP/05), all as per drawing and as make approved by GE.

Locker Bed side Steel FD-1029, all as per drawing and as make approved by GE.

ALMIRAH STEEL (MEDIUM) (DRG NO FD-1032) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1mm MS plain black sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. Six lever brass lock shall be provided as per Godrej pattern. (iv) One steel chrominium plated handle shall be provided to the drawer. (v) Locker of the almirah shall be provided with locking arrangement operated with handle as per Godrej pattern. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamelled paint (silver grey colour) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (xiii) Rest all as shown on drawing.

Table 900 x 900 x 760mm Steel FD-1009, all as per drawing and as make approved by GE.

Table Bed Side (MAP) (FD/E6/MAP/15(R)) (i) Pipe shall be 18mm MS square pipe (18 gauge) black powder coated. (ii) Top and back portion above top of Table bed side shall be of 18mm thick Prelaminated particle board (one side decorative finish shade as approved by GE and other side white balancing lamination ) as specified here-in- before. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in top and pull out tray. Back of table bed side shall be of 6 mm thick commercial plywood as per IS-303. (iii) Sides and back of drawers shall be provided with 12 mm thick commercial plywood as per IS-303. Bottom of drawer shall be provided with 6 mm thick commercial plywood. (iv) Movement of Pull out tray and drawers shall be made on teak wood runners. One aluminum anodized handle shall be provided to each drawer. (v) Stoppers shall be 2nd class Hard wood (Sal/benteak/Bijasal/Hollock). (vi) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vii) All exposed surfaces of timber and plywood shall be French polished. (viii) All joints fixing shall be done in accordance with standard workmanship and specifications. (ix) Rest all as shown on drawing.

Hard Bed Steel FD/E6/MAP/18, all as per drawing and as make approved by GE.

Receptable PVC FD/E6/MAP/13, all as per drawing and as make approved by GE.

Note. Drgs referred in BOQ are available in the Office of BSO, GE Chandigarh. Bidders shall refer the same with prior intimation to GE.

CITIZEN FURNITURE INDUSTRIES

M/s Rajesh Kumar Jain

Kalia Construction Company