8904 SPECIAL REPAIRS TO BLDG NO CH-142 (COOK HOUSE) AT KALINA MILITARY CAMP UNDER GE NORTH MUMBAI

Amount

Taking down of chowkats or frames with shutters exceeding 1.50 sqm not exceeding 4.0sqm each (with out taking off shutters from the frames) after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge.

Taking down of chowkats or frames with shutters not exceeding 1.5sqm each (with out taking off shutters from the frames) after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter carefully, area exceeding 1 sqm but not exceeding 2sqm each including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing),deposting debris out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of plain cement concrete (unreinforced) of any description and in any position, not otherwise specifically provided for,and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Demolition of reinforced cement concrete of any description in any position including necessary scaffolding arrangement (reinforcement cut as required to facitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. Note : Reinforcement obtained from this item shall be handed over to contractor on account of sch of credit

Demolition of brickwork built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Dismantling boarding of any description and in any position, fixed with nails complete all as specified and as directed by Engineer-in-Charge.

Material and labour for mild steel hold fast confirming to Fe 410-S or Fe 310-S complete all as specified and as directed by Engineer-in-Charge.

Material and labour for painting to small articles such as holdfast brackets or cantilevers n.exc 30cm projection and blocks, labels etc not exceeding 10sqm each complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Providing,Plain cement concrete type B0 1:2:4 (using graded stone aggregates 12.5mm) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work for fair finished surfaces complete all as specified and as directed by Engineer-in-Charge.

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 35mm thick factory made plain framed panelled shutter 2nd class hardwood rail and style (any number of panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 35mm thick factory made 2nd class hard wood glazed and skeleton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.24 (b) complete all as specified and as directed by Engineer-in-Charge. Make: M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pvts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 156 of SSR Part II (pertaining to item No 08080) including necessary aluminium builders hardware for one door to be provided such as 100mm dia butt hinges - 3Nos, tower bolt 200mm dia - 2Nos, handle 200mm long - 2 Nos etc complete all as specified and as directed by Engineer-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6Nos screws to be provided for each frame all as specified and as directed. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces.

Supply and fix stainless steel butt hinges, medium weight, 100mm size all as specified and directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 140mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Material and labour for preparing new wood surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimer paints/ Dulux

Supply and fix 15 micron coloured aluminium sections for sliding or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix 15 micron coloured aluminium anodised grill of design No DG-202, 10 mm thick, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLE of Associated group or equivalent make as approved by GE

Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium windows and wooden door shutters etc complete all as specified and as directed by Engineer-in-charge.

Supply and fix 5.50mm thick sheet glass, pin headed type ordinary quality fixing with oil putty and glazing clip, in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Hindustan Pilkington Glass works / Saint Gobin / Modi Float / Modiguard

Supply and fix Solar control film 50 micron, reflective type, sticked to glass panes as per instructions of manufacturers complete all as specified and as directed by Engineer-in-Charge. Make : Hindustan Pilkington Glass works / Saint Gobin / Modi Float / Modiguard

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell

Material and labour for non skid coloured ceramic tiles(joint free), 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell

Material and labour for joint free, coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm , on vertical surfaces etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including cement plaster 10mm thick in CM (1:4) complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell

Material and labour for joint free, coloured glazed ceramic tiles of size 300mm x 200mm x 7 mm thick, on vertical surfaces etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including cement plaster 10mm thick in CM (1:4) complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell

Material and labour for machine cut Kota stone slab flooring 20-25 mm thick over cement screed bed 15 mm in CM (1:3) base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer in Charge.

Material and labour for machine cut Kota stone slab flooring 20-25 mm thick over cement screed bed 10 mm in CM (1:3) base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer in Charge.

Material and labour for polishing to existing kota stone flooring complete all as specified and directed by Engineer in Charge.

Material and labour for polishing to existing kota stone skirting complete all as specified and directed by Engineer in Charge.

Material and labour for 75mm thick PCC (1:4:8) type D2, (using 40mm graded stone aggregate) as in sub base, finished even and rough complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick Plain Cement Concrete (1:3:6) type C2, nominal mix (using 40mm graded stone aggregate) as in plinth protection & finished even and fair without using extra cement with necessary slope and joints between wall and concrete filled with mastic filling complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15mm thick rendering in two coats (10mm + 5mm) with cement mortar 1:4 on fair faces of brick or concrete surfaces, finished even and fair mixed with water proofing compound all as per manufacturers instructions etc, complete all as specified and as directed by Engineer-in-Charge Note: WPC will be measured and paid separately.

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for 10mm thick rendering with cement mortar 1:6 on fair faces of brick or concrete surfaces complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 5mm thick in cement mortar 1:3 on fair faces of concrete surfaces of ceiling and finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing new plastered surfaces and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of wall primer etc complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old plastered or unplastered decorated wall surfaces including complete removal of existing treatment and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old plastered wall surfaces including complete removal of existing treatment on wall and applying two coats of Acrylic weather proof coat 100 % exterior grade paint over one coat of acrylic primer on wall surfaces complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for preparation of old plastered wall surfaces complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of alkali resistant primer over 1.5mm wall care putty including preparation complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of old plastered or unplastered decorated ceiling surfaces including complete removal of existing treatment and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for anodised aluminium snap grid frame work for false ceiling conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, 4 mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm , cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system including 10mm PVC insulation panels stuck to 1mm printed PVC sheet suitably placed in aluminium grid system complete all as specified and as directed by Engineer-in-Charge.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed by Engineer-in-Charge.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by Engineer-in-Charge.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-Charge.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs GI tubing, medium grade, 15 mm bore with all fittings and connections and fixing to walls/floor including cutting chases in brick walls pinning in and making good disturbed surfaces using with cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Zenith / Swastik / Prakash

Supply and fix in repairs vitreous china wash hand basin, white, flat back of size 580 mm x 450 mm excluding taps, waste chain and plug and porcelain stopper including brackets ,cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson Note:- Pillar taps, waste fittings, PVC connection, bottle trap shall be measured and paid separately as "Supply only

Supply only 15mm bore pillar tap, fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with long screwed shanks and fly nuts, screwed for 15mm iron pipe complete all as specified and as directed by Engineer-in-Charge. Make :Soma / Leader / Zoloto / Jaquar

Supply only 32mm bore waste coupling of PTMT (half or full threaded) (Minimum weight 45gms) complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix 32mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed by Engineer-in-Charge. Make :Soma / Leader / Zoloto / Jaquar

Supply and fix in repair 15mm bore angle cock with flange, cast copper alloy, chromium plated,screwed down, screwed for iron pipe or for brass ferule, heavy duty complete all as specified and as directed by Engineer-in-Charge. Make :Soma / Leader / Zoloto / Jaquar

Supply and fix in repair PVC connection 15mm dia with PTMT nuts of length 600mm complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repair 75 mm bore UPVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix in repairs aluminium anodised tubular towel rail, 20mm dia, D type, 60cm long, between flanges including suitable bracket complete all as specified and as directed by Engineer-in-Charge. Make : Crown / Jindal / Essess / Swastik

Supply and fix in repair UPVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix in repair 32 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/cm2 with all pipe fittings, fixed complete to walls, ceiling or laid in floors complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed. Make :Soma / Leader / Zoloto / Jaquar

Supply and fix in repair vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap, connector piece of CI pipe upto 'T'/ 'Y' joint and connection to trap and to flushing pipe, anti-syphonage pipe etc and provision of lime concrete bedding complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repair PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets,complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repair flush pipe of polyethylene of low or high density or PVC, 32mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repair overhead shower rose brass chromium plated 125 mm dia, heavy duty pattern with swivel joints, suitable for jointing to 15 mm bore steel water tubing or union complete all as specified and as directed by Engineer-in-Charge. Make :Soma / Leader / Zoloto / Jaquar

Material and labour Pre-cast cement concrete block masonry 1:3:6 type C1, (using 20mm graded stone aqggregate), with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Stainless steel sink without drainage board 1.00 mm thick (AISI 304 quality), glossy finish, for kitchen or laboratory with plugs, waste pipe, washers, including bedding in cement mortar to dwarf walls or including fixing cantilever cast iron brackets, connecting union etc. overall size 495mm x 330mm with bowl size 410mm x 330mm x 160mm, with flush pipe, complete all as specified and as directed by Engineer-in-Charge. Make : Diamond / Nirali / Neelkant/Parryware/Prayag

Supply only Chromium plated 32mm waste coupling for glazed wash basin with long screwed shanks and flynit 32mm diameter complete all as specified and as directed by Engineer-in-Charge. Make : Diamond / Nirali / Neelkant/Parryware/Prayag

Removing of spoils obtained from demolition to be outside MD land of distance exc 1.5 Km but n.exc 5km and deposited where as directed complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully old unserviceable copper/aluminum point wiring (light,fan,socket or power) any type with bakelite sheets complete with fittings such as switches, ceiling rose, pendants, regulators, sockets,dimmers etc with and making good disturbed surfaces of walls, floors, etc. to match with existing surface etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for point wiring with and including single core fire retardant low smoke PVC insulated and unsheathed, multistranded copper conductor cable conforming to IS-694 of size 1.5 sqmm 1100 volts grade drawn through and including PVC conduit/casing capping 20mm / 25mm on surface conforming to IS-9537 and accessories including 16 SWG mild steel sunken box for housing of switch, socket, regulator etc, concealed in wall, flush with wall, with 3 mm thick PVC laminated top cover complete with and including 1.5 sqmm fire retardant low smoke PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete for one Light/fan point controlled by one switch complete all as specified and as directed by Engineer-in-Charge. Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG

All as per item no.80 above but one 3 pin 5 Amps switch socket combination, on same board complete all as specified and as directed by Engineer-in-Charge.

All as per item No.80 above but one 3 pin 5 Amps switch socket combination, on independent board complete all as specified and as directed by Engineer-in-Charge.

Material and labour for point wiring with and including single core fire retardant low smoke PVC insulated and unsheathed, multistranded copper conductor cable conforming to IS-694 of size 2.5 sqmm 1100 volts grade drawn through and including PVC conduit/ casing capping 20mm / 25mm on surface conforming to IS-9537 and accessories including 16 SWG mild steel sunken box for housing of switch, socket, regulator etc, concealed in wall, flush with wall, with 3 mm thick PVC laminated top cover complete with and including 2.5 sqmm fire retardant low smoke PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete for one Light/fan point controlled by one switch complete all as specified and as directed by Engineer-in-Charge. Make:Plaza/Finolex/Anchor/Havells/Nicco/Polycab/RPG

Material and labour switch socket combination 2 in 1 3 pin 15Amps flush type universal complete all as specified and as directed by the Engineer-in-charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Material and labour switch socket combination 2 in 1 3 pin 5Amps flush type universal complete all as specified and as directed by the Engineer-in-charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix Switch piano type single pole one way 5 amps 230 volt flush type complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix ceiling rose, surface bakelite, 65 x 50mm, three terminals, AC, 230 volts, mounted on PVC square block complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply,install,test and commissioning batten type tube light LED 20w, trendy wall mounted, with extruded aluminium housing, with integrated LED driver, including necessary electrical wiring etc including taking down old unserviceable fittings complete all as specified and directed by Engineer-in-Charge. Make :Havells Cat Part LUMILINEBS20WLED865SPCWH or equivalent in CG, Philips, HPL, Halonix, Surya

Supply only led lamps 9W 230Volts complete all as specified and as directed by Engineer-in-Charge. Make: Philips Make :Havells,CG,Philips,HPL,Halonix,Surya

Supply fixing and connecting from existing ceiling rose with 3 core flexible copper wire of required length 1' x 1' LED 15w recess softline luminaire suitable for armstrong/grid ceiling with high brightness LEDs and PMMA extruded diffuser given glare free light and good aesthestic appeal,complete all as specified and directed by Engineer-in-Charge. Make :Havells,CG,Philips,HPL,Halonix,Surya

Supply and fix in repair 20w LED building light fitting, pressure die cast aluminium housing, heat resistance toughened glass with frame and IP 66 protection for better optics for uniform distribution and connection with three core copper flexible cable 16/0.20 mm from ceiling rose to fitting complete all as specified and as directed by Engineer-in-Charge. Make :Havells,CG,Philips,HPL,Halonix,Surya

Supply and fix in repairs double door, sheet metal enclosure powder coated MCB DB SPN 8 way with 200 Amps rated bus bar, 240 volt,IP 42 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs MCB TPN,63amps, 415 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs MCB SPN,5 to 32 Amps, 415 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Supply and fix in repairs MCB SP,5 to32 Amps, 415 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: Larsen & Toubro/ABB/Siemens/Schneider/Havells

Material and labour Earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to and including galvanised earth lead wire 6 mm dia, 7.5 m long, by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel with provision of charcoal & common salt packed upto minimum 150 mm all around the earth plate, and protected by 15 mm bore light grade galvanised iron pipe and connected to control board / panel / equipment complete all as shown in electrical plate No.3 of MES schedule Part I with PCC pit in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, MS angle iron frame of size 50mm x 50mm x 5mm, cast iron cover with locking arrangements, GI 20 mm bore medium grade pipe and CI funnel with wire mesh for watering arrangement including necessary excavation and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connection of one twin core cable, flat or circular, stranded aluminium conductor electric power cable, LT 1100 volt grade, heavy duty of size 10sqmm, 2 core suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire including taking down one complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair ceiling fan regulator AC, 230 volts electronic step type complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix in repair Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings or angle lamp holder complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/crabtree/Leader

Supply and fix in repairs GI bracket made out of 40 mm bore GI pipe, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x5mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engineer-in-charge. Make : SAIL/Indian tube co/Lanco Andra pradesh/Kubota pipes Ltd

Taking down ceiling fan/exhaust fan/wall mounted fan of any make/type/size/sweep, at site from any height of the building for any defect, servicing complete, repairs/ overhauling including replacement of quarter pins,nuts,bolts,rubber reels and replacing with new 2 core PVC sheathed cable of 23/0.0076 from ceiling rose to ceiling fan,preparing surfaces by scrapping and removing dust etc and filling cavities with one coat of filler and applying synthetic enamel paint by spraying and writing MES Nos in block letters as per existing & re-fixing in same position including successful testing on full load with blade complete all as specified and as directed by Engineer-in-Charge.

industrial suppliers

S.N Enterprises

SHREE SHIV SHANKER ENTERPRISE