Repair and renovation of Houses of Type-5,3,2 and 1 at Thermal Colony GNDTP, Bathinda.

Site Clearance Clearing jungle manually including uprooting rank vegetation, grass, woody vegetation upto30cm girth measured at height of 1m above ground level and removal of rubbish upto distance of 50m outside the periphery of the area cleared

Dismantling brick work, tile, masonry or tile lining In cement

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

Regrading terracing of mud plaster covered with tiles or bricks in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud plaster to proper,slope, relaying mud plaster Gobri leaping and tiles or bricks grouted in cement mortar 1:3 (1cement and 3 fine sand) including replacing unserviceable tiles, or bricks with new over and disposal of unserviceable material to the dumping ground within 50m lead including applying bitumen on roof including heating and carrying to roof @1.65 kg/sqm, cleaning of roof, polythene sheet complete in all respects to the Entire satisfaction of Er.-in-Charge (The cost of new tiles or bricks excluded).

Supply of new tiles

Repair of existing tile terracing to stop seepage of water including cleaning of roof, applying roof sealant paint, re-grouting in cement mortar 1:3 (1cement and 3 fine sand).

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Dismantling of Reinforced cement concrete

Cement concrete 1:8:16 With brick ballast 32mm/ 40mm gauge

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

Cement concrete 1:2:4 with stone ballast mixing by mechanical meansusing concrete mixer volumetric type

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

Scrapping

White wash and colour wash

Cement plaster

12.5 mm thick cement plaster 1:5

Plastering on under side of ceiling 10mm thick cement plaster 1:3

Cement rendering on plaster 1mm thick

Disposal of malba (taking 1 KM Lead) i/c loading, unloading complete.

White washing (Three coat)

Colour washing (two or more coats)

Distempering with dry distemper of approved manufacture two or more coats over one priming coat to give an even shade

Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade

Finishing walls with cement based water soluble exterior paint such as snowcem, robbiacem etc. two or more coats to give an even shade

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseedoil,Varnish, and Chalk Mitti including finishing the surface to required finish complete.

Applying pink primer or aluminum priming coat on woodwork including preparation of surface knotting and stopping etc.

Applying priming coat with metal primer on new steel or iron work including preparation of surface.

Painting two coats with synthetic enemel paints in all shads on old wood or mettalic or plastered or concrete surfaces to give an even shade including rubbing down old paint.(With Special quality paint)

Preparation for plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish.

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled.

a) Doors of area 3 sqm and below

b) Windows of area 3 sqm and below

Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge. Door and window frame of size 113mmx60mm with 35mm wide single rebate

Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge. Doors and windows frame of size 151mm x60mm with 35 mm wide double rebate weighing 3.95 kg per meter.

Kiln seasonal Hollock wood cup board chowkats including iron hold fasts, iron hinges corner straps, wooden knobs or handles fixed in position (Size 45 x 60mm).

Hollock wood doors, shutter including hinges, screws, choks, cleats, stop cords etc complete fixed in position a)panelled, glazed or glazed and panelled. 35mm thick

Wire gauge hollock wood door shutter without springs housed in chowkhats (a)35mm thick

Hollock wood cupboard shutter with both sides plywood panels 30mm thick complete fixed in position excluding the cost of handles, bolts hasp with staple but including labour for fixing them.

Cost of aluminium fittings complete for doors, windows such as tower bolts, handles, stoppers and screws etc for these fittings (exc sliding bolt) for shutter area above 0.5 sqm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250mm x 16mm

Providing and fixing commercial plywood 18mm thick.

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position

Concealed in wall: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge.

Internal-Exposed on wall-Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in-Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings with one step PVC solvent cement and testing of pipes complete as per direction of Engineer-in Charge.

Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete.25 mm i/d Brass Ball valve.

Providing and fixing in position automatic brass Ball Cock in tanks.20mm i/d

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required. Through wall 22.86 cm thick.

Providing and fixing in position Chinaware Indian Orisa water closet size 580x440 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI makred including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI marked, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. (a) 100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm

Excavation manually in trenches with straight or open cutting in built up street/ lane having wall to wall width of street/ lane upto 3.0 metre, for intramural sullage drains, extramural intercepting drains and outfall drains, storm water channels and other work contingent or incident thereto, to full dimensions and depth as shown on the drawings or as shall be required by Engineer in-charge including dressing to correct sections and dimensions according to templates and levels, dewatering of rain water, diversion of traffic. Providing and fixing and maintenance of caution boards, fencing, night signals, for leads upto 15m and for all lifts and subsequent refilling, watering and dressing upto groung level, including removal of surplus spoil from the site upto 15 metre distance complete in all respects. (i) All classes of soil except rocky

Excavation in trenches with straight or open cutting in streets , lanes or in open area with 3D/JCB or excavator including mannually dressing bed ,trimming sides & side slopes for sewers & manholes to full depth as Shown in Drawings, Including dressing to correct sections and dewatering of rain water , provision for diversion of traffic, protection of existing services i.e. telephone cables , electric lines , water supply lines and gas lines etc. night signals , profiles, pegs, sight rails.boning rods, fixing and maintenance of caution boards, fencing , refilling trenches, watering , ramming and restoration of surface to original level and removal of surplus spoils from the site of works up to one chain (15 meter) complete in all respects. (a) For depth not exceeding 3.0 Mtr

Constructing brick masonry manhole in cement mortar 1:5 ( 1 cement : 5 coarse sand ) R.C.C. top slab 20cm thick using M-20 mix by using mixer and vibrator, TMT Fe500 @ 80.00 kg/per cum, foundation concrete 1:4:8 mix (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making 40mm thick benching in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, Orange coloured PVC steps including RCC cover with frame complete as per standard design complete in all respects (b) Inside size 90x150 cm and 120 cm deep

Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects (d) 200mm o/d pipe

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete1:2:4 benching 12.50mm thick cement plaster 1:2 with a floatingcoat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mmx 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.

Size 450mmx450mm in side with RCC 455mmx455mm cover and frame light duty double seal

600mm x 900mm inside with 455mm x 455mm cover and frame light duty double seal

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:2 (1 cement : 2 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete. a) For pipes 100 to 250mm diameter

Providing and fixing 110mm dia.U.P.V.C Rain water pipe of 4kgf./sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in- charge.

Providing and fixing110mm dia.U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. (a) UPVC 110 mm bend

Providing and fixing 110 mm dia. U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. (a) UPVC 110 mm Coupling /Sockets

Providing and fixing jet spray with 2'-6" long PVC pipe. (A) With C.P. Bass Nut

Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect.

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect b) C.P brass towel ring

P&F in position vitreous chinaware white lavatory suites of approved make (to the approval of engineer- in- charge) consisting of CP brass waste 32mm dia with one no CP Brass pillar tap including rack bolt screw pair 115mm long without CP fittings complete in all respect.

Size 450mm x 300mm

Size 550mm x 400mm

Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect. b) Rectangular Sink with Deluxe Border Single Bowl Overall Size 555 mm x 475mm x 200 mm

P&F in position CP brass overhead shower 1 flow with shower arm with 15mm i/d inlet of approved make

P&F in position CP acrylic shelf with CP bracket and guard rails of approved make of size 560X130mm

P&F in position CP brass soap dish of approved make complete in all respect

P&F in position 5mm thick bevelled edge mirror of superior glass complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, CP brass screrws and washers and S/S studs on top complete in all respect of size 600mmX450mm

Providing & fixing in position CP brass flange dome of approved make complete in all respects.

P&F in position CP brass extension piece 25mm long to 100mm longs of approved make with fixtures complete In all respect i) CP brass extension piece 25mm to 50mm long

Providing & fixing in position CP brass hexa nipple 15mm of approved make complete in all respects.

P&F in position 15mm i/d bib cock of approved make (to the approval of Er-In-Charge) complete in all respect

i) CP brass bib cock long nose/ long body foam flow without flange

ii) CP brass bib cock body foam flow without flange

iv) Brass bib cock/stop cock 15mmX400gms

P&F in position Stop cock/ angle valve of approved make complete in all respect

i)CP brass 15mm concealed stop cock with flange

i)CP brass 15mm angle valve without flange

P&F in position pvc flexible tube connection of approved make complete in all respect b) size 15X450mm with brass nut

P&F in position single socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of EDC manufacture of of any other reputed firm inc cutting, jointing, wasting complete of type B d)75mm o/d SWR UPVC pipes

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects.

P&F in position SWR UPVC specal for soil waste vent or anti syponage pipes as per IS: 14735 including cutting and wastage etc cutting holes in walls, roofs etc

iv) Door elbow 90 degree 110mm o/d pipes

ix) P trap/floor trap 110mm x 110mm

(vi) P trap/Floor Trap 75mm x 75mm

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer-in charge) with cover with suitable locking arrangement andmaking necessary holes for inlet,outlet and over flow pipes but without fittings and base support for tank. (Triple layer)

P&F in position GIPVC tank nipple of approved make a)25mm i/d

Cleaning of sewer lines with super suction and other machinery upto 8" dia pipe

RECESSED HGW CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealedmetal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches,16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for wall sand CI3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq.mm, 1100 volts grade (For 6Amp. wall socket & plu ncluding the cost of above material, cutting and filling up of chases (with finishing the surface):

(i)a Wiring Fan point (without fan box)

(ii) Wiring light point

(iii) Wiring call bell point

(v) Wiring 6Amp wall socket point

(vi) Wiring 16/20AMp power plug control point

Supply and erection of PVC insulated single core FRLS copper conductor cable IS:694/1990 marked left bare in pipe or casing of suitable size excluding the cost of supply and erection of pipe or casing.

(ii)PVC insulated copper conductor single core FRLS cable (ISI marked) overall 1.5 sq.mm, 1100volts grade un-sheathed

(iii)PVC insulated copper conductor single core FRLS cable (ISI marked) overall 2.5 sq.mm, 1100volts grade un-sheathed

(iv)PVC insulated copper conductor single core FRLS cable (ISI marked) overall 4 sq.mm, 1100volts grade un-sheathed

Supply & erection of PVC pipes as per IS:9537: Part-III & HDPE pipes as per IS:4985:1995 (fire retardant) for wiring purposes including bends, nspection boxes etc.,where necessary including other petty material as per PWDGeneral Specifications 2010:- (a) heavy duty PVC conduit pipe 20mm dia (ISI marked 2mm thick) flushed

Supply & erection of PVC flexible pipe complete without compression glands, locking arrangements, check nuts as required of dia 20mm

Supply & erection of swicthes, sockets & other accessories (flush piano type/modular type accessories) in the exisitng bakelite/ modular frame including fixing & connections and petty material etc

(xxvi) Ceilling Rose (flush piano type)

(xxvii) bakellite Batten holder(Large Size)

Supply and erection of Miniature Circuit Breakers in the existing MCB distribution board as per PWDGeneral Specifications 2010 including connections withsuitable size of thimbles/lugs.

(ii) MCB SP 6-32 Amp

(vi) MCB DP 6-32Amp

(vii) MCB DP 40Amp

Supply and erection of sheet metal double door distribution boards IP 43 IK 09 metal door (dust protected) as per IS:8623 1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated bus bars, shrouded neutral bars, earth bars, cement spill protector, color coded interconnecting wire set, cable ties, blanking plates and circuit identification lable and of reqd no of ways for MCB breakers/RCBOs/RCCB's in the existing MCB distribution board as per PWD GeneralSpecifications including connections with suitable size ofthimbles and bonding to existing earth etc.

(ii) SP&N double door distributon board 8-Way

(v)TP&N Horizontal Double Door Distribution Board 4 way each

P&F in position ceiling fan 48" of approved make

P&F 4' long LED lights 20W of approved make

P&F in position Led bulb 9W of approved make

P&F in position exhaust fan 300mm sweep of approved make.

Nicking cement concrete surface

Providing and laying vitrified floor tiles of different sizes in light colour shades made using Double Charge technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades laid with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. Size 600 mm x 600 mm

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado laid with cement based high polymer modified quick set tile adhesive (Water based) confirming to IS:15477, complete white cement slurry in joints including corners angles and beading

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x 300 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement : 4 fine sand) including grouting the joints of tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Dismantling cement conglomerate floors 25mm to 50mm thick without concrete base

Conglomerate floor 40mm thick ement concrete topping 1:2:4 using mechanical mixer for mixing of material

20mm thick grey polished skirting or dado consisting of bottom layer of 16mm thick cement sand plaster1.3 and finished 3mm thick topping of neat cement rubbed and polished including rounding of junction with floors.

Removing of Doors to fix floor tiles, cutting/resizing of doors as per site requirement and fixing of these doors including accessories with chowkhats including cost of planning, screws, nails etc. complete in all respects.

Excavation manually in trenches for pipe lines with straight or open cutting in streets and lanes in built up area where width of street / Lane from wall to wall is less than 3 meter including trimming and dressing sides levelling of bedsof trenches to correct grade,cutting joint holes, refilling consolidation,watering, including thecost of dewateringof rainwater,diversionfor traffic, night signals. Providing & fixing caution boards,watching, fencing, etc. and removal of surplus soil from the site upto15meter distance complete in all respects. (i)Earth work upto 1.5 m. Depth in All classes of soil except rocky

Supplying and fixing of ISI Marked CID-joint (complete withnut, bolts & rubberring) as per IS:8794 for repair of pipe line including cutting, jointing and testing etc.but excluding cost of excavation complete. (a) 80mm

Providing,Laying, fixing & jointing of P.V.C. Pipes as per ISI-4985 (ISI marked with the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications. (ii)75mm o/d pipe of 10 Kgf. / sqcm

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (b)0.60 mm (+ 0.05 %) thick

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for seperately)

(a) For Fixed Portion and Chaukhats

(b) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug /neoprene gasket required

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-In-Charge. Prelaminated particle board with decorative lamination on Both side.

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item) (i) Float glass panes of 5 mm thickness

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade machine made rubber moulded smooth finish with strong vibratory process or with vibrohydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge IS Code:15658 (2006)

Extra cost for using darker fast shade for interlocking pavers tiles of any shape and thickness instead of using grey colours

Chicken Mesh

Centring and shuttering for parapet, fascias and other similar items including edges.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S.clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerincharge. The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

HCI Grating Jali of size 100mm x 100mm

Hydraulic Door Spring ISI marked of Shivalik or equivalent make

Door Spring ISI marked of Shivalik or equivalent make

Please Enable Macros to View BoQ information