SPECIAL REPAIR TO BLDG NO. P 40 AND PROVN OF KITCHEN AND TOILET BEHIND BLDG NO P 01 UNDER GE NARANGI

Amount

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes, laying of cable etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling, in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified and as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in Slabs supported on walls beams and columns in floors,roofs,landings, balconies,canopies,deck slabs and in shelves and the like etc complete all as specified as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in Columns, pillars, piers, posts and struts etc.complete all as specified as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in beams, seimic bands, cantilevers, bressumers and lintels complete all as specified as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in chajjahs complete all as specified as directed.

M/L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed.

M/L formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers, lintels over 1.5m clear span, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc. for fair finished flat surfaces of concrete complete all as specified and as directed.

Use and waste for Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M/L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works, not exceeding 200mm thick ( Horizontal or sloping) complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia as in reinforcement bar complete all as specified and as directed.

M & L for mild steel TMT bars 6 to 8mm mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns,hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia as in reinforcement bar complete all as specified and as directed.

M&L for mild steel TMT bars 6 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and directed.

Demolition of brick /stone massonry work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks (locally available best quality) straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

All as per item No. 19 above but except bricks. (Serviceable bricks obtained from demolition shall be reused).

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) including removal of spoils/ demolished materials not exceeding 50m and depositing complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4, type B1 (using 20mm graded stone aggregate) as in floor complete all as specified and as directed.

M&L for 75mm thick PCC type D-2, 1:4:8 (40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 40mm thick PCC type B-1, 1:2:4 (20mm graded stone aggregate) as in flooring,and finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for providing 75 mm thick PCC (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) as in plinth protection. Plinth protection shall be laid in alternate bays n exc 2 sqm, 10 mm thick joints shall be provided, joint shall be filled with bitumen mastic, bitumen mastic shall comprises of 1 part of hot bitumen 85/25 and 3 parts of sand all by weight finished cement concrete surface even and fair without using extra cement complete all as specified and as directed.

S&F pre painted galvalume aluminum and zinc alloy coating with GI based corrugated steel sheet 0.50 mm thick of a colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F pre painted galvalume aluminum and zinc alloy coating with GI based plain steel sheet 0.50 mm thick of a colour having tensile strength of 550 Mpa as in ridges fixed with self tapping screws complete all as specified and directed.

Dismantling of asbestos cement sheet (Corrugated semi corrugated etc) as in roof covering complete all as specified and directed.

M & L in repair 4mm thick asbestos cement plain building boards, fixed to timber frame work with screw as in ceilings complete all as specified and directed.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:3) on concrete surfaces of roof mixed with WPC as per manufacturer,s instruction complete all as specified and directed. Note : WPC will be measured and paid seperately.

M&L for rendering 5 mm thick in CM (1:3) on concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plastered surface of ceilingand applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old plastered surface of wall and applyingone coat of white wash complete all as specified and directed.

M&L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for complete removal of old treated surfaces on walls and applying one coat of alkali resistant primer and applying two coats of oil bound distemper complete all as specified and directed.

M&L for complete removal of old treated surfaces on walls and applying one coat of alkali resistant primer applying two coats of cement base paint etc complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in frame work in any position complete all as specified and directed.

M&L second class hard wood in scantlings clean sawn timber in framed work complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area n.exc. 1.5 Sqm each including builders hardware complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each including builders hardware complete all as specified and as directed.

Taking down shutter of any description n.exc 1 Sqm each complete all as directed.

Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each complete all as directed.

M&L 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F 30 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and directed.

S&F steel windows with side hung shutters glazed, both side openable ( outside glazed window and inside fly proof window) including projecting type hinges with steel handle , and steel peg stay complete with glazing bars dovetailed or welded with 12mm dia square bars or round bar of approved design welded to steel window frame complete all as specified & as directed.

S&F 30mm thick second class hard wood glazed and skeleton shutters, open rebated divided into square and prepared to receive glass, gauge etc (with sash bar of any number), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (b) complete all as specified and directed.

S&F PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tube for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stills and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ scaled to the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement as per drawings and specifications as catered in SSR Part – II 2020.

S&F 1.25mm thick pressed steel frame of size 105x60mm for doors/windows with single rebates including necessary fixing lugs, hinges, lock strike plates, filling in PCC !:3:6 type C-0 in hollow portion etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F Rolledmld steel roof trusses ( framed) trussed purlins, crane gantries, rails and fastenings and heavy brackets framing ( Beam, tee, angle, channel or flat section) including distace pieces, cleats etc confirming to Fe 410-W ( Gde E-250 Quality A)complete all as specified & as directed.

M&L for plain cement concrete (1:3:6) type C1 (using 20 mm graded crushed stone aggregate) as in hold fast block or bed block complete all as specified and directed.

S&F 100mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm in size extruded aluminium handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm in size extruded aluminium handles, fabricated type, anodised complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed

S&F stainless steel butt hinges 100 mm long medium weight complete all as directed.

S&F, stain-less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples complete all as specified and as directed.

S&F in repairs, stain-less steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane complete all as specified and directed.

Demolition of stone slabs and tiles of any description and thickness in floors, approns etc. complete all as specified and directed.

M&L for 20-25mm thick Kota stone slab in riser of steps, skirting, dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 10 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 20-25mm thick Kota stone slab flooring laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth and wall tiling including cement mortar bedding (but excluding backing), removing rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300mmx200mmx 6mm to 7mm thick, set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as skirting, dados and risers to steps over and including 10 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for 20mm thick granite ( any type) machine cut ,as in steps, jambs, pillars, window cills, cookong platforms and the like laid over cement screed of 15mm thick in CM 1:4 including pointing in white cement 1:2 using marble dust with admixtures of pigments match the shade of granite stone including rubbing and polishing complete all as specified and as directed.

M&L coloured Non-skid ceramic tiles 7 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match existing surfaces over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L coloured Non-skid ceramic tiles 7 mm thick (Square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match existing surfaces over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L coloured Non-skid ceramic tiles 7 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in vertical surfaces such as skirting, dados and risers to steps over and including 10 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for 75 mm thick plain cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in floors/ sub base of tiles/floor of hard standing/path etc complete all as specified and directed.

S&F in repair pre-polished cement concrete chequered tiles area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm and 25 mm thick with white cement and pigments of approved maked jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) complete all as specified and directed.

M&L for preparation of old surfaces of wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old surfaces of steel and steel based surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint r complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel and steel based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Taking up or down 15 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate

S&F GI tubing15 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Refixing only old serviceable 15 mm bore Steel tubing and connections as obtained from taking up/down old steel tubing including provision of new fittings in new or old position to walls,ceiling, flooring etc. complete all as specified and as directed.

Taking up or down 20 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed.

S & F GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Refixing only old serviceable 15 mm bore Steel tubing and connections as obtained from taking up/down old steel tubing including provision of new fittings in new or old position to walls,ceiling, flooring etc. complete all as specified and as directed.

S&F in repairs stop valves 15 mm dia cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed.

S&F stop valves 15 mm dia cast copper alloy, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed.

S&F stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directe.

S&F in repairs concealed stop valves 15 mm dia cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed.

S&F Bib taps 15mm dia fancy type cast copper alloy chromium plated, with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as directed.

S&F in repairs Bib taps 15mm dia fancy type cast copper alloy chromium plated, with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as directed.

S&F in repair 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polye-thylene water storage tanks triple layer ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I with and including 20 mm bore dia -ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polye-thylene water storage tanks triple layer ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I with and including 20 mm bore dia -ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc including dismantling of old tank of any description complete all as specified and directed.

S&F stainless steel sink with drainage board made of 1mm thick stainless steel sheet for kitchen with plugs, washers, waste coupling and pipe, cast iron cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs, Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest etc. ( excluding cistern and flush pipe) including S or P Trap and provision of concrete bedding and making good to floor complete all as specified and as directed.

S & F in repairs, vitreous china wash down water closet (padestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for padestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

S&F in repair plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repair vitreous china wash basin white flat back size 550 mm x 400mm including all fittings and CP Pillar tap, including cutting for and pinning in ends of brackets or erecting stand etc complete (waste coupling 32mm bore CP, 32mm bore PVC waste pipe, cast iron brackets etc shall be deemed to be included in the quoted rate) complete all as specified and directed.

S&F in repair CP swivel shower rose of 125 mm dia and suitable for fixing 15 mm bore iron pipe all as specified and directed.

S&F in repair 15mm dia PVC connection pipe 600mmm with PTMTnuts complete all as specified and directed

S&F in repair Waste coupling of PTMT (half or full threaded) Minimum weight 40 to 60 gms complete all as specified and directed.

S&F in repair Waste coupling of PTMT (half or full threaded) suitable for urinals Minimum weight 32 to 45 gms complete all as specified and directed.

S&F cast iron floor trap with 100mm dia outlet with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F in repairs Vitreous china urinal, half stall white (excluding flushing cisterrn) including urinal spreader, PVC connection, 40mm PVC waste pipe & 40mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F Vitreous china urinal, half stall white (excluding flushing cisterrn) including urinal spreader, PVC connection, 40mm PVC waste pipe & 40mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and directed.

M&L for 2nd class hardwood Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

Hacking out old broken glass (any thickness, quality or description) from wooden frame or metal frame or aluminium frame or stone concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick figured glass pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

S&F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor as in waste/soil pipe etc complete all as specified and directed

S&F in repairs 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor as in waste/soil pipe etc complete all as specified and directed

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and directed

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge.

M & L for point wiring with 1.5 sqmm, single core, PVC insulated and PVC unsheathed FRLS cable, 1100 volts grade IS-694 marked, with multistranded copper conductors and earth continuity wire with 1.5 Sqmm cable (including connecting to earth dolly) laid/fixed in and including concealed in PVC rigid conduit on walls/ceiling, and also including sunk type pressed steel teRminal box made out of galvanised iron sheet thickness not less than 1mm and 3 mm thick plastic laminated sheet top covers for One light/fan/exhaust fan point controlled by one number one way 5 Amp switch complete all as specified and as directed.

All as per item serial No 120 here-in-before but for One light point controlled by 2 Nos. 2- way switch.

All as per item No 120 here-in-before but for One 3 pin 5 Amp switch socket outlet on independent board

All as per item serial No 120 here-in-before but for One 3 pin 5 Amp socket outlet on same board with other switches.

All as per item No 120 here-in-before but wiring with 2.5 sqmm size single core multistranded copper conductor cable for 6 pin 15 Amps switch socket combination outlet on independent board with 2.5 sqmm PVC insulated and unsheathed copper conductor as earth and connected to earth dolly.

S&F switch piano, flush type single pole one way 5 Amps 240 volt complete all as directed.

S&F switch piano, flush type single pole two way 5 Amps 240 volt complete all as directed.

S&F socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as directed.

S&F switch socket combination outlet , 2-in-1, 5 Amp flush type complete all as directed.

S&F switch socket combination multipurpose, 5 in 1, , 5 & 16 Amp flush type complete all as directed. .

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as directed.

S&F lamp holder insulated PVC/ Polycarbonate/ bakelite body, with back plate suitable for batten fitting or PVC round or squre box, complete all as directed

S&F stepped type electronic fan regulator, two module size, flush type complete all as directed.

M&L for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit shall be measured as one unit.

M&L for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit shall be measured as one unit.

S&Fin repair regal batten for LED Tube rod pre-wired including LED tube double sided 1x20W connecting up with aluminium housing and sheathed 1100 volt grade flexible copper cable & fix on 2 no. of PVC block complete all as directed. (Make:- Havells, Model No: REGALBATTENT8UPTO1X22WDSBSWH+CRSTAL1213T8DSTL20WLED865SGLASS or equivalent model of make Bajaj / Philips / GE / Crompton)

S&F in repairs LED box type fitting pre-wired including LED tube 1x10W connecting up with PVC insulated and sheathed 1100 volt grade flexible copper cable and fix on 2 no of PVC block ccomplete as specified and directed.(Make:- Jaguar Model No. LGLZ01X010XC/ LGLZ01X010XN/LGLZ01X010XW or Havells Model No. LUMILINEPLUSBS10WLED865SPCSS or equivalent model of make Philips /GE/Crompton)

S&F in repairs round shape 12 Watt 220 volts AC surface type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F in repairs decorative hexagonal bulk head LED luminaire 10Watt,6000K with IP 66 Protection complete as specified and directed. (Make: Havells Model HEXAFT10WLED857SSYMBOPC or equivalent of crompton/Bajaj/Philips)

Supply and fixing building security light bracket made of GI pipe 40 mm bore medium grade (bend to shape), 2.00 metre long and fixed with Ms flat iron clamp(clamp shall be 40 x 5mm), nuts, bolts and washers on pole complete all as specified and directed.

Supply and fixing in repairs building security light bracket made of GI pipe 40 mm bore medium grade (bend to shape), 2.00 metre long and fixed with Ms flat iron clamp(clamp shall be 40 x 5mm), nuts, bolts and washers on pole complete all as specified and directed.

Supply and fixing building security liminaires WSPD 48 Watts epoxy powder coated pressure die cast aluminium housing with weather proof gasket for LEDs and control gear compartments, pressure die cast aluminium frame with heat resistant toughened clear glass fixed with SS screws. CRee LED/Equivalent colour temp-5700 K +/-300 K lens , IP-66, lumen efficiancy >100, lm/w. surge protection, 4 KV internal ( built in) with twin core conductor complete all as specified and directed including testing on completeion. Make: Havells Cat No. ENDURAPEARNEOSL48WLED757SASYTOPC or equivalent in Philips/WIPRO/CG.

Supply and fixing in repair building security liminaires WSPD 48 Watts epoxy powder coated pressure die cast aluminium housing with weather proof gasket for LEDs and control gear compartments, pressure die cast aluminium frame with heat resistant toughened clear glass fixed with SS screws. CRee LED/Equivalent colour temp-5700 K +/-300 K lens , IP-66, lumen efficiancy >100, lm/w. surge protection, 4 KV internal ( built in) with twin core conductor complete all as specified and directed including testing on completeion. Make: Havells Cat No. ENDURAPEARNEOSL48WLED757SASYTOPC or equivalent in Philips/WIPRO/CG.

M&L for plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m deep below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth lead wire 4 mm dia or 8 SWG bolted (with GI nuts, bolts & check nuts) and earth plate electrode at one end and connected to main switch board/ DBs etc. at the other, earth strip encased(protected) in and including 15 mm bore GI pipe medium grade with all fittings from top of electrode to main switch board/ DBs etc fixed with and including 25 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-2 using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work complete all as specified and shown in electrical plate No 3 of SSR Pt-I including demolition of old earthing complete all as specified and directed..

Taking down ceiling /wall / exhaust fans of any sweep carefully and and transporting from any location to MES E/M store yard and back after repairing and refixing in position duly painted with one coat of synthetic enamelled paint by spraying including filling cavities with filler connecting up after neccessary repair as directed. complete all as specified and directed.

Rewinding exhaust fan by cutting the existing copper winding of any sweep and make with super enamelled copper wire of suitable size incl all insulating materials varnishing and neating complete incl satisfactory testing of fan on full load to entire satisfaction of Engineer-in-Charge complete all as specified and directed.

Rewinding Ceiling fan by cutting the existing copper winding of ceiling fan of 1200/1400MM capacity and make any type with super enamelled copper wire of suitable size incl all insulating materials varnishing and neating complete incl satisfactory testing of fan on full load to entire satisfaction of Engineer-in-Charge complete all as specified and directed.

Supply only down rod made of 15mm dia GI pipe medium grade 45 cm long incl machining/ threading/drilling hole of size suitable for nuts and bolts washer and split pin suitable for any size and make of fan complete all as specified and directed.

S&F exhaust fan with louvers shutter 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm, and necessary connecting items with flexiable PVC insulated multistranded copper conductor cable of size 1.5 sqmm and making good to the disturbed surfaces complete all as specified and directed.

S&F exhaust fan with louvers shutter 230V, 50 Hz, RPM 1200, copper winding of sweep 250mm, and necessary connecting items with flexiable PVC insulated multistranded copper conductor cable of size 1.5 sqmm and making good to the disturbed surfaces complete all as specified and directed.

S&F in replacement MCB DB, double door sheet metal enclosure SPN 8 way with 200 A rated bus bar complete and grouted in wall with PCC (1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and directed. (Make :- Legrand/ Siemens/Schnider/L&T)

S&F MCB DB, double door sheet metal enclosure SPN 4 way with 200 A rated bus bar complete and grouted in wall with PCC (1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and directed. (Make :- Legrand/ Siemens/Schnider/L&T)

S&F in replacement MCCB DB, IP-43, double door sheet metal enclosure VTPN 4 way with 250 Amps rated copper bus bar 415 volt complete and grouted in wall with PCC (1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and directed. (Make :- Legrand/ Siemens/Schnider/L&T)

S&F in repair MCCB, 100 Amps, 415 V, 16KA complete all as specified and as directed. (Make :- Legrand/ Siemens/Schnider/L&T)

S&F in repair MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA, C-series marked fixing in DBs (DBs catered separately in this Schedule) (Make :- Legrand/ Siemens/Schnider/L&T)

S&F MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA, C-series marked fixing in DBs (DBs catered separately in this Schedule) (Make :- Legrand/ Siemens/Schnider/L&T)

S&F in repair MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series complete all as specified and directed. (Make :- Legrand/ Siemens/Schnider/L&T)

S&F MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series complete all as specified and directed. (Make :- Legrand/ Siemens/Schnider/L&T)

S&F in repair MCB Tripple pole & neutral 40 to 63 Amps in accordance with IS/IEC 60898-1, 415 V, 50 Hz,10 kA,C-series complete all as specified and directed. (Make :- Legrand/ Siemens/Schnider/L&T)

Taking down carefully by unscrewing from board/outlet boxes, fitting and fixturessuch as switches, sockets,ceiling rose, lamp holders, brackets ceiling fitting ,bulkhead fitting, tube light fitting and regulator etc for reuse at site or carring to the store ( To be measured only when found in all respect complete for reuse) and making good disturbed surface of wall, flooretc complete all as directed by Engineer-in-Charge.

Refixing serviceable fittings/ fixtures as obtained from serial item No. 158 here in before and connecting up with suitable size cable in location as directed.

M & L for XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10 sqmm 2 core laid in trenches /floor or fixed on wall /pole in including brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

Supply and spreading clean dry river sand in cable trenches as in cable cushioning complete all as specified and as directed. (Note: Punned thickness shall be measured and paid)

M&L for Sub class ‘B’ old size well burnt brick laid flat in trenches over the cable for protection of LT cable complete all as specified and as directed.

SHANKAR ENTERPRISE

S. R. TRADING

VENUS TRADING CORPORATION