REPAIRS MAINT OF EXTERNAL WATER SUPPLY PUMPS PIPE LINES DG SETS CLEANING OF OH TANKS UG SUMPS WELLS AND CONNECTED WORKS AT DGQA MD ACCN AREA AND DAD QTRS UNDER GE STM

Amount

Dismantling the defective mono block pump set of capacity 1 HP from foundation by opening of coupling and foundation bolts and transpoting to workshop for repairing and reassembling after servicing and overhauling complete with oiling/greasing, lubricating the parts includng repair / renewal of worn out parts and spray painting with one coat of synthetic enamel paint of existing colour and writing SM/MES No with white paint and installation commissioning and testing on full load complete all as specified and directed by Engineer - in - Charge. Note:- (i) The rate quoted for the item shall includes labour charge only for maint/repair and renewal of defective/UNSV spares/accessories. Supply only Spares shall be measured and paid separately. (ii) Cost of other minor items/spares such as nut, bolts washers, gaskets, paints etc which are not covered under Sch 'A' but required for effective functioning of the plant shall be deemed to be included in the rate quoted.

All as per item No 1 here-in-before but capacity 2.0 to 3.0 HP three phase monoblock pumpset

All as per item No 1 here-in-before but capacity 5.0 HP three phase monoblock pumpset

All as per item No 1 here-in-before but capacity 7.5 HP three phase monoblock pumpset

All as per item No 1 here-in-before but capacity 10 HP three phase monoblock pumpset

All as per item No 1 here-in-before but capacity 15 HP three phase monoblock pumpset

Supply only CI impeller suitable for 2.0 to 3.0 HP mono block pump set

Supply only ball bearing suitable for 2.0 to 3.0 HP mono block pump set

Supply only CI impeller suitable for 5 HP mono block pump set

Supply only ball bearing suitable for 5.0 HP mono block pump set

Supply only motor coupling assembly with wire suitable for 5.0 HP mono block pump set

Supply only CI impeller suitable for 7.5 HP mono block pump set

Supply only ball bearing suitable for 7.5 HP mono block pump set

Supply only motor coupling assembly with wire suitable for 7.5 HP mono block pump set

Supply only CI impeller suitable for 10 HP mono block pump set

Supply only ball bearing suitable for 10 HP mono block pump set

Supply only motor coupling assembly with wire suitable for 10 HP mono block pump set

Supply only CI impeller suitable for 15 HP mono block pump set

Supply only ball bearing suitable for 15 HP mono block pump set

Supply only motor coupling assembly with wire suitable for 15 HP mono block pump set

Dismantling the motor of monoblock pumpset of capacity 1.0 to 2.0 HP removing the existing burnt out winding and rewinding with copper winding wire of existing gauge and weight including renewal of all insulation material and terminal lead for AC single phase 230 volts grade and other minor items required for making motor functional, reassembling the motor and shifting back to pump house and testing complete all as directed by Engineer-in-Charge

All as per item No 21 here-in-before but capacity 3.0 HP three phase monoblock pumpset

All as per item No 21 here-in-before but capacity 5.0 HP three phase monoblock pumpset

All as per item No 21 here-in-before but capacity 7.5 HP three phase monoblock pumpset

All as per item No 21 here-in-before but capacity 10 HP three phase monoblock pumpset

All as per item No 21 here-in-before but capacity 15 HP three phase monoblock pumpset

All as per item No 21 here-in-before but capacity 20 HP three phase monoblock pumpset

Dismantling the defective centrifugal pump set of capacity 10/12.5 HP from foundation by opening of coupling and foundation bolts and transporting to workshop for repairing and reassembling after servicing and overhauling complete with oiling/greasing, lubricating the parts includng repair / renewal of worn out parts and spray painting with one coat of synthetic enamel paint of existing colour and writing SM/MES No with white paint and installation commissioning and testing on full load complete all as specified and directed by Engineer - in - Charge. Note:- (i) The rate quoted for the item shall includes labour charge only for maint/repair and renewal of defective/UNSV spares/accessories. Supply only Spares shall be measured and paid separately. (ii) Cost of other minor items/spares such as nut, bolts washers, gaskets, paints etc which are not covered under Sch 'A' but required for effective functioning of the plant shall be deemed to included in the rate quoted.

All as per item No 28 here-in-before but 20.0 HP three phase centrifugal pumpset

All as per item No 28 here-in-before but 25.0 HP three phase centrifugal pumpset

All as per item No 28 here-in-before but 100.0 HP three phase centrifugal pumpset

Supply only CI impeller suitable for 10/12.5 HP centrifugal pump set

Supply only ball bearing suitable for 10/12.5 HP centrifugal pump set

Supply only motor coupling set suitable for 10/12.5 HP centrifugal pump set

Supply only shaft for 10/12.5 HP centrifugal pump set

Supply only CI impeller suitable for 20 HP centrifugal pump set

Supply only ball bearing suitable for 20 HP centrifugal pump set

Supply only motor coupling set suitable for 20 HP centrifugal pump set

Supply only shaft for 20 HP centrifugal pump set

Dismantling the motor of centrifugal pumpset of capacity 10/12.5 HP removing the existing burnt out winding and rewinding with copper winding wire of existing gauge and weight including renewal of all insulation material and terminal lead for AC single phase 415 volts grade and other minor items required for making motor functional, reassembling the motor and shifting back to pump house and testing complete all as directed by Engineer-in-Charge

All as per item No 40 here-in-before but capacity 20.0 HP three phase centrifugal pumpset.

All as per item No 40 here-in-before but capacity 25.0 HP three phase centrifugal pumpset.

All as per item No 40 here-in-before but capacity 100HP three phase centrifugal pumpset.

Taking out defective submersible pump set of capacity 3.0 HP from bore well for repair by lifting GI tubing of size 50 mm from up to 220 feet depth by means of chain pully block or other T&P, disconnecting electrical and pipe line connection, transporting to workshop including repair/renewal of worn out parts, servicing and overhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pumpset including motor with one coat of synthetic enamel paint and shifting back to borewell, lowering commissioning and testing on full load complete all as specified and directed by Engineer-in-charge. Note:- (i) The rate quoted for the item shall includes labour charge only for maint/repair and renewal of defective/UNSV spares/accessories. Supply only Spares shall be measured and paid separately. (ii) Cost of other minor items/spares such as nut, bolts washers, gaskets, paints etc which are not covered under Sch 'A' but required for effective functioning of the plant shall be deemed to included in the rate quoted.

All as per item No 44 here-in-before but capacity 5.0 HP submersible bore well pumpset.

All as per item No 44 here-in-before but capacity 7.5 HP submersible bore well pumpset.

All as per item No 44 here-in-before but capacity 10 to 12.5 HP submersible bore well pumpset.

All as per item No 44 here-in-before but capacity 15 HP submersible bore well pumpset.

Supply only thrust bearing complete suitable for 3 HP submersible bore well pump set

Supply only gun metal bearing bush suitable for 3 HP submersible bore well pump set

Supply only stainless steel studs and nuts suitable for 3 HP submersible bore well pump set

Supply only shaft for pump suitable for 3 HP submersible bore well pump set

Supply only bowl assembly suitable for 3 HP submersible bore well pump set

Supply only key suitable for 3 HP submersible bore well pump set

Supply only oil seal body suitable for 3 HP submersible bore well pump set

Supply only thrust bearing complete suitable for 5 HP submersible bore well pump set

Supply only gun metal bearing bush suitable for 5 HP submersible bore well pump set

Supply only stainless steel studs and nuts suitable for 5 HP submersible bore well pump set

Supply only shaft for pump suitable for 5 HP submersible bore well pump set

Supply only bowl assembly suitable for 5 HP submersible bore well pump set

Supply only key suitable for 5 HP submersible bore well pump set

Supply only oil seal body suitable for 5 HP submersible bore well pump set

Supply only thrust bearing complete suitable for 7.5 HP submersible bore well pump set

Supply only gun metal bearing bush suitable for 7.5 HP submersible bore well pump set

Supply only stainless steel studs and nuts suitable for 7.5 HP submersible bore well pump set

Supply only shaft for pump suitable for 7.5HP submersible bore well pump set

Supply only bowl assembly suitable for 7.5 HP submersible bore well pump set

Supply only key suitable for 7.5 HP submersible bore well pump set

Supply only oil seal body suitable for 7.5 HP submersible bore well pump set

Supply only thrust bearing complete suitable for 10 to 12.5 HP submersible bore well pump set

Supply only gun metal bearing bush suitable for 10 to 12.5 HP submersible bore well pump set

Supply only stainless steel studs and nuts suitable for 10 to 12.5 HP submersible bore well pump set

Supply only shaft for pump suitable for 10 to 12.5 HP submersible bore well pump set

Supply only bowl assembly suitable for 10 to 12.5 HP submersible bore well pump set

Supply only key suitable for 10 to 12.5 HP submersible bore well pump set

Supply only oil seal body suitable for 10 to 12.5 HP submersible bore well pump set

Supply only thrust bearing complete suitable for 15 HP submersible bore well pump set

Supply only gun metal bearing bush suitable for 15 HP submersible bore well pump set

Supply only stainless steel studs and nuts suitable for 15 HP submersible bore well pump set

Supply only shaft for pump suitable for 15 HP submersible bore well pump set

Supply only bowl assembly suitable for 15 HP submersible bore well pump set

Supply only shaft for motor suitable for 15 HP submersible bore well pump set

Supply only stainless steel motor coupling with ring suitable for 15 HP submersible bore well pump set

Supply only bowl assembly ring suitable for 15 HP submersible bore well pump set

Dismantling the motor of submersible (vertical type) pumpset of capacity 3HP, removing the existing burnt out winding and rewinding with copper winding wire of existing gauge and weight including renewal of all insulation material, "O" rings and filling of cooling oil with oil seal and terminal lead for AC, 3 Phase, 415 volts grade and other minor items required for making motor functional, reassembling and testing complete all as directed by Engineer-in-Charge.

All as per item No 85 here-in-before but capacity 5 HP submersible bore well pump set

All as per item No 85 here-in-before but capacity 7.5 HP submersible bore well pump set

All as per item No 85 here-in-before but capacity 10 to 12.5 HP submersible bore well pump set

All as per item No 85 here-in-before but capacity 15 HP submersible bore well pump set

Taking out defective submersible open well type pump set of 5 HP capacity of depth upto 40 feet from open well / UG sump for repair by lifting of GI tubing of size upto 100 mm bore by means of chain pully block or other T & P, disconnecting electrical and pipe line connection, transporting to workshop including repair/renewal of worn out parts, servicing and overhauling complete with oilling/greasing, lubricating the parts, painting of submersible pumpset including motor with one coat of synthetic enamel paint and shifting back to openwell/ UG Sump, reassembling, lowering commissioning and testing on full load complete all as specified and directed by Engineer-in-charge. Note:- (i) The rate quoted for the item shall includes labour charge only for maint/repair and renewal of defective/UNSV spares/accessories. Supply only Spares shall be measured and paid separately. (ii) Cost of other minor items/spares such as nut, bolts washers, gaskets, paints etc which are not covered under Sch 'A' but required for effective functioning of the plant shall be deemed to included in the rate quoted.

All as per item No 90 here-in-before but capacity 7.5 HP submersible open well type pump set

All as per item No 90 here-in-before but capacity 10 HP submersible open well type pump set

Supply only thrust bearing complete suitable for 5 HP submersible open well pump set

Supply only gun metal bearing bush suitable for 5 HP submersible open well pump set

Supply only stainless steel studs and nuts suitable for 5 HP submersible open well pump set

Supply only impeller suitable for 5 HP submersible open well pump set

Supply only seal suitable for 5 HP submersible open well pump set

Supply only impeller key suitable for 5 HP submersible open well pump set

Supply only rotor slleve suitable for 5 HP submersible open well pump set

Supply only thrust bearing complete suitable for 7.5/10 HP submersible open well pump set

Supply only gun metal bearing bush suitable for 7.5/10 HP submersible open well pump set

Supply only stainless steel studs and nuts suitable for 7.5/10 HP submersible open well pump set

Supply only impeller suitable for 7.5/10 HP submersible open well pump set

Supply only seal suitable for 7.5/10 HP submersible open well pump set

Supply only impeller key suitable for 7.5/10 HP submersible open well pump set

Supply only rotor sleeve suitable for 7.5/10 HP submersible open well pump set

Dismantling the motor of submersible open well pumpset of capacity 5HP, removing the existing burnt out winding and rewinding with copper winding wire of existing gauge and weight including renewal of all insulation material, "O" rings and filling of cooling oil with oil seal and terminal lead for AC, 3 Phase, 415volts grade and other minor items required for making motor functional and reassembling and testing complete all as directed by Engineer-in-Charge

All as per item No 107 here-in-before but 7.5 HP capacity

All as per item No 107 here-in-before but 10 HP capacity

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m deep for foundation and getting out in hard/dense soil complete all as specified and as directed.

Returning filling in foundation including levelling watering and well ramming in layers not exceeding 25cm using excavated soil all as directed.

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed.

S&F GI tubing medium grade with necessary fittings and fixtures fixed to wall, ceiling or laid in floors etc. complete of 15mm bore including taking down unserviceable steel tubing and connections and removing to store all as specified and as directed.

All as per item No 113 here-in-before but 20mm bore pipe

All as per item No 113 here-in-before but 25mm bore pipe

All as per item No 113 here-in-before but 40mm bore pipe

All as per item No 113 here-in-before but 50mm bore pipe

All as per item No 113 here-in-before but 65mm bore pipe

All as per item No 113 here-in-before but 80mm bore pipe

All as per item No 113 here-in-before but 100mm bore pipe

S&F GI tubing medium grade with necessary fittings and fixtures laid in trenches complete of 15mm bore including taking down unserviceable steel tubing and connections and removing to store all as specified and as directed.

All as per item No 121 here-in-before but 20mm bore pipe

All as per item No 121 here-in-before but 25mm bore pipe

All as per item No 121 here-in-before but 40mm bore pipe

All as per item No 121 here-in-before but 50mm bore pipe

All as per item No 121 here-in-before but 65mm bore pipe

All as per item No 121 here-in-before but 80mm bore pipe

All as per item No 121 here-in-before but 100mm bore pipe

Supply and laying of DI pipe 100mm dia with spigot and socket ends with necessary fittings and rubber tyton joints, class K-7 including taking down the existing unserviceable pipes complete all as specified and as directed.

Supply and laying of DI pipe 150mm dia with spigot and socket ends with necessary fittings and rubber tyton joints, class K-7 including taking down the existing unserviceable pipes complete all as specified and as directed.

Supply and laying of DI pipe 200mm dia with spigot and socket ends with necessary fittings and rubber tyton joints, class K-7 including taking down the existing unserviceable pipes complete all as specified and as directed.

S&F 15mm dia gun metal globe or gate valve of brass heavy duty ISI marked with iron wheel head, butterfly handles screwed both ends for iron pipe complete including taking down existing unserviceable valve all as specified and as directed.

All as per item No 132 here-in-before but 20mm dia

All as per item No 132 here-in-before but 25mm dia

All as per item No 132 here-in-before but 40mm dia

All as per item No 132 here-in-before but 50mm dia

All as per item No 132 here-in-before but 80mm dia

S&F cast iron 80mm dia sluice valve IS 14846-2000 PN 1.6 both flanged heavy duty drilled and installed with brass spindle gun metal face rings rubber gasket 3mm thick MS bolts nuts and washers graphite rope complete including taking down existing unserviceable valve all as specified and as directed.

S&F cast iron 100mm dia sluice valve IS 14846-2000 PN 1.6 both flanged heavy duty drilled and installed with brass spindle gun metal face rings rubber gasket 3mm thick MS bolts nuts and washers graphite rope complete including taking down existing unserviceable valve all as specified and as directed.

S&F cast iron 150mm dia sluice valve IS 14846-2000 PN 1.6 both flanged heavy duty drilled and installed with brass spindle gun metal face rings rubber gasket 3mm thick MS bolts nuts and washers graphite rope complete including taking down existing unserviceable valve all as specified and as directed.

S&F cast iron 200mm dia sluice valve IS 14846-2000 PN 1.6 both flanged heavy duty drilled and installed with brass spindle gun metal face rings rubber gasket 3mm thick MS bolts nuts and washers graphite rope complete including taking down existing unserviceable valve all as specified and as directed.

S&F foot valve cast Iron flange type heavy duty of 80mm dia complete with gasket, bolt & nut, washer etc. conforming to IS 4038 duly fitted in suction line of centrifugal pump set / mono block pump set inside the UG sump complete including taking down existing unserviceable valve all as specified and as directed.

All as per item No 142 here-in-before but 100mm dia

All as per item No 142 here-in-before but 150mm dia

All as per item No 142 here-in-before but 200mm dia

Supply and fix cast iron NON RETURN VALVE of 200 mm dia, ISI marked, double flanged including rubber gasket, nuts and bolts complete including dismantling / taking up and removing the existing unserviceable complete all as specified and as directed :-

All as per item No 146 here-in-before but 150mm dia

All as per item No 146 here-in-before but 100mm dia

All as per item No 146 here-in-before but 80mm dia

All as per item No 146 here-in-before but 50mm dia

Supply and fix cast iron air release valve 100 mm dia, ISI marked, double flanged including rubber gasket, nuts and bolts complete including dismantling / taking up and removing the existing unserviceable complete all as specified and as directed :-

All as per item No 151 here-in-before but 150mm dia

All as per item No 151 here-in-before but 200mm dia

Cleaning the internal surfaces of Over Head Tank of 10000 gallons capacity at any height / staging by scrapping down/brushing and removing all silt dirt, algae etc from walls, floors, washing/ cleaning with water and applying one coat of white wash to all internal surfaces of walls and ceilings and one coat of cement base paint to all external surfaces including top surfaces of OH tanks including providing one coat of anti corrosive bituminous paint on all old steel surfaces such as vent pipes, inlet, outlet pipes, ladder and one coat of synthetic enamel paint to MS pipe railing complete all as directed by Engineer-in-charge. NOTE : (i) Rate quoted is deemed to include Paintings to oblitering labels using black paint same as existing dimensions and writing particulars etc using white paint with height of letters same as existing writing. (ii) The contractor shall provide all safety measures for the labour to work in heights.

All as per item No 154 here-in-before but 20000 gallons capacity

All as per item No 154 here-in-before but 50000 gallons capacity

All as per item No 154 here-in-before but 75000 gallons capacity

All as per item No 154 here-in-before but 100000 gallons capacity

Cleaning the internal surfaces of Under Ground Sump of capacity 5000 gallons by scrapping down/brushing and removing all silt dirt, algae etc from walls, floors, washing/ cleaning with water and applying one coat of white wash to all internal surfaces of walls and bottom of doom, applying one coat of anti corrosive bituminous paint on all steel surfaces of sump including oblitering labels using black paint same as existing dimensions and writing particulars etc using white paint with height of letters same as existing writing complete as directed by Engr-in-charge

All as per item No 159 here-in-before but 7500 gallons capacity

All as per item No 159 here-in-before but 10000 gallons capacity

All as per item No 159 here-in-before but 20000 gallons capacity

All as per item No 159 here-in-before but 50000 gallons capacity

Preparing the old painted surfaces of DI/CI/GI pipe line of 200mm dia and applying one coat of synthetic enamel paint black colour to existing suction pumping line near the pump house sump to pump house from pump to delivery line through raising and delivery main of the Overhead tank of following sizes of pipe:

All as per item No 164 here-in-before but MS/CI/DI pipe of 150mm dia

All as per item No 164 here-in-before but MS/CI/GI pipe of 100mm dia

All as per item No 164 here-in-before but CI/GI pipe of 80mm dia

All as per item No 164 here-in-before but GI pipe of 50mm dia

All as per item No 164 here-in-before but GI pipe of 25mm dia

All as per item No 164 here-in-before but GI pipe of 20mm dia

Cleaning the swimming pool complete of size 25.10 m long, 11metre width and depth varing from 1 to 5m, of capacity 1,50,000 gallons by bailing out the entire dirty water from the swimming pool using higher capacity pump set and removing the complete scale formation by applying HCL solution and rubbing the surfaces with the wire brush to remove the silt formation and including washing the entire swimming pool all as directed by the Engineer-in-charge

Preparing the old painted surfaces of filteration vessel of size 3000mm dia and 4m height and applying one coat of synthetic enamel paint complete all as pecified and as directed.

Preparing the old painted surfaces and applying one coat of synthetic enamel paint complete all as pecified and as directed.

Preparing the old painted surfaces of suction sweeper pump and motor of capacity 5 HP and applying one coat of synthetic enamel paint complete all as pecified and as directed.

Developing / flushing of bore wells for a period of 6 hours using compressed air method upto availability of crystal clear water including removing and fixing the installation in original location all as specified and directed.

Demolition of brick work built in cement mortar including all quions arches, pillars etc and removing debris outside the MD land complete all as specified and directed.

M&L for brick work with fly ash bricks of old size built in CM (1:6) straight or curved on plan exceeding 6m mean radius complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provided complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and similar bands, plinth courses, string courses, lacing course, parapet, copings, kneelers, apex stones, including necessary form work complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished even and smooth, without using extra cement complete all as specified and as directed.

M&L for applying three coats of white washing on newly prepared wall surfaces all as specified and as directed.

M&L preparation of steel surfaces of any description exceeding 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

Supply and fix direct on line starter three phase suitable upto 5 HP Pumpset in sheet metal enclosure, 415V, including taking out old unserviceable all as directed.Make: L & T MF 1 or equivalent.

Supply and fix direct on line starter three phase suitable upto 7.5 HP Pumpset in sheet metal enclosure, 415V, including taking out old unserviceable all as directed.Make: L & T MF 1 or equivalent make as specified in list of manufacturers.

Supply and fix Auto star delta starter with three phase, 415 volts, with and including prevention facility suitable for upto 10HP pump set including taking out old unservicable all as directed. Make : L & T MK 1 or equivalent make as specified in list of manufacturers.

Supply and fix Auto star delta starter with three phase, 415 volts, with and including prevention facility suitable for upto 12.5HP pump set including taking out old unservicable all as directed. Make : L & T MK 1 or equivalent make as specified in list of manufacturers.

Supply and fix Auto star delta starter with three phase, 415 volts, with and including prevention facility suitable for upto 15 HP pump set including taking out old unservicable all as directed. Make : L & T MK 1 or equivalent make as specified in list of manufacturers.

Supply and fix Auto star delta starter with three phase, 415 volts, with and including prevention facility suitable for upto 20 HP pump set including taking out old unservicable all as directed. Make : L & T MK 1 or equivalent make as specified in list of manufacturers.

Supply and fix single phase preventor 3 phase 415 volts including taking out old unservicable all as directed all as directed

M&L for rolled mild steel joist, channels, angles, or tee sections, fixed independently, without connecting plates, etc as Fe-410-W (gde-E-250), Quality 'A' complete all as specified and directed.

S&F mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe-410-W (Gde-E-250) quality ‘A’ complete all as specified and as directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintel hinges, large hasps and staples, chains, handmade sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290-0 Gde E-165 complete all as specified and as directed

S & F cast iron fittings of any type with nuts, bolts and washers for 80mm to 150 mm dia pipes complete all as specified and as directed.

Servicing, comprehensive maintenance of DG sets of capacity 40/62.5KVA including servicing of all parts as per maintenance manual, supply and renewal of the following items complete all as directed. (i) Diesel filter (pre+ micro) - 2 Nos (ii) Engine oil filter - 2 Nos (iii) Replacement of Engine oil (iv) Radiator coolant - 1 Litre

M & L for epoxy type cable jointing kit complete with jointing material for 1100 volts flat submersible copper conductor cable 6/4 sqmm 3 core all as specified and as directed. Make: Reychem/Birla 3M or equivalent.

M & L for GI tubing heavy grade 80mm dia with necessary fittings laid in floor/ceiling/ lowering in well complete all as specifed and as directed.

M & L for GI tubing heavy grade 50mm dia with necessary fittings laid in floor/ceiling/ lowering in well complete all as specifed and as directed.

M & L for PVC insulated sheathed unarmoured flexible copper conductor cable 3 core 4 sqmm, 1100 volt grade sutable for submersible pumps complete all as specifed and as directed.

S & F three pole contactor with AC coil suitable for motor upto 12.5 HP complete all as specified and as directed.

S & F control relay with AC coil suitable for motor upto 12.5 HP complete all as specified and as directed.

S & F MCCB four pole, 415 volts, 63 Amps, 16 KA with fixed thermal and magnetic settings complete all as specified and as directed.

S & F MCCB four pole, 415 volts, 125 Amps, 25 KA with fixed thermal and magnetic settings complete all as specified and as directed.

M/S.RANGA AND CO

RK ENTERPRISES