GE/S(U)-01/2022-23 SPECIAL REPAIR TO BOUNDARY WALL NEAR BLDG NO P70 P51 P35 IN BIKRAM ENCLAVE AND PROVN OF 04 X TOILETS NEAR BLDG NO NP157 AT ARMY PUBLIC SCHOOL JR WING UNDER GE SOUTH UDHAMPUR

Amount

Surface excavation not exceeding 30 cm deep in hard /dense soil and ageraging 15 Cm deep & getting out complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation complete all as specified and as directed.

PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Returning, filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm in any type of soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Damp proofing course to horizantal or vertical surface including form work in PCC 1:2:4 type B-1 25mm thick complete all as specified and as directed.

Hard core of guage n exc. 63 mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded crushed stone aggregate as in sub base floor complete all as specified and as directed.

25 mm thick for PCC 1:3:6 using 20 mm graded crushed stone aggregate as in plinth protection using extra cement complete all as specified and as directed.

Non skid ceramic coloured tiles 400x400x7 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Glazed ceramic coloured tiles 600x300x7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified complete all as specified and as directed.

Rendering 15 mm thick in CM 1:6 on brick work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in CM 1:4 on brick work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and as directed.

Preparation of new plaster surfaces of wall and applying three coats of white wash complete all as specified and as directed.

Preparation of new plaster surfaces and applying two coats of cement base paint and over one coat of primers complete all as specified and as directed.

Preparation of new plaster surfaces and applying three coats of white wash on ceiling complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Form work to soffits of suspended slabs and similar work not exceeding 200 mm thick for flat rough finished surfaces of concrete complete all as specified and as directed.

Form work to sides and soffit of floor or roof beams lintels, beam haunching ,girders lintal cantiliver including supports overhung etc complete all as specified and as directed.

RCC 1:1.5:3 type B-1 using 20 mm graded crushed stone aggregates for slabs supported on walls beams and columns in floors ,roof ,landing ,balconies ,canopies slabs and in shelves and the like complete all as specified and as directed.

RCC 1:2:4 type B1 20mm graded crushed stone aggregates for for lintels bands and roof bends complete all as specified and as directed.

Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups ,spacers and binder cut to length bent to shape required including cranking, bending spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour sheet reinforced with MS square tube complete all as specified and as directed.

Factory made solid PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be coverred with heat moulding plain colour PVC 'C; channels having a PVC sheets strips of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail ,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheets to be fitted in the MS frame welded /sealed to the stiles & rails with suitable arrangement complete all as specified and as directed.

100 mm size butt hinges extruded aluminium alloy with galvanised mild steel hinges pin anodised type B-2 complete all as specified and as directed.

200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

Aluminium handles cast type of 150mm size complete all as specified and as directed.

Steel Ventilators with top hung shutters including hinges steel peg stay complete all as specified and as directed.

S&F for sheet glass 3mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in Each pane complete all as specified and as directed.

GI tubes 15 mm dia medium grade laid in trenches or fitted on walls complete all as specified and as directed.

GI tubes 20 mm dia medium grade laid in trenches or fitted on walls /floor complete all as specified and as directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

110 mm PVC (SWR) branch piece, (Single T) equal or unequal with access door complete all as specified and as directed.

110 mm PVC (SWR) vent cowl complete all as specified and as directed.

110mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement in repair complete all as specified and as directed.

100 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and as directed.

100 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and as directed.

Vitreous china ware wash down water closet pan, (pedestal pattern) coloured including connection to drain and to flushing pipe, anti syphonage pipe etc complete all as specified and as directed.

10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and as directed.

vitreous china white wash hand basin (flat back or angle back type) size 550x400mm white including brackets, pedestal, waste fittings brass chromium plated, CP waste cupling, 32mm dia, waste pipe, PVC connection 15 mm bore with PTMT nuts of length including 15mm dia CP pillar tap fancy type complete all as specified and as directed.

Chromium plated toilet paper holder complete all as specified and as directed. Make :- Jaquar Cat Part No ACN 1153N and equivalent in CERA.

Glass shelf with chromium plated guard rails complete all as specified and as directed. Make :- Jaquar Cat Part No ACN-1171N and equvalent in CERA.

600mm long Brass chromium plated towel rail fancy type complete all as specified and as directed. Make :- Jaquar Cat Part No ACN-1111NM and equvalent in CERA.

Soap dish complete all as specified and as directed. Make Jaquar Cat Part No ACN 1131N and equvalent in CERA.

Providing and injecting chemical emulsion for Post constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion @ of 7.50 ltr per sqm of the vertical surface of the sub structure to a depth of 300 mm including excavated channel along the wall and rodding etc complete all as specified and as directed. (Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment).

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed. (Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment)

Providing and injecting Treatment of soil under existing floors using emulsion @ 1 litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and as directed. (Note: The treatment work shall be carried through authorised agencey only , and certificate for the same for warranty shall have to frunished before submitting payment)

Providing and injecting of voids in masonary using chemical emulsion one litre per hole, at 300mm intervals including drilling holes complete all as specified and as directed. (Note: The treatment work shall be carried through authorised agencey only, and certificate for the same for warranty shall have to frunished before submitting payment) and drilling holes at 45 degree and plugging the same with cement mortar 1:2 to match with existing surface.

CP waste coupling 32 mm dia PTMT (half or full threaded) minimum weight 450 gms complete all as specified and as directed.

PVC waste pipe 32mm bore with cup and washers complete all as specified and as directed.

15 mm bore centre hole basin mixer with round spout with 450 mm long copper pipes and brass nuts with out Pop up complete all as specified and as directed. Make: Jaquar Cat Part No CON 167KNB

Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and as directed. Make :- Jaquar Cat Part No:PRS 077

PVC connection 15mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer complete all as specified and as directed. (Suitable for Basin Mixers) Make: Jaquar Cat Part No ALD-803AB

PVC connection 15mm bore 450 mm long Braided Hose with two 15 mm Nut & Rubber washer without nipple complete all as specified and as directed. Make: Jaquar Cat Part -ALD-805B

CP Bib taps cast copper alloy with crutch or butterfly handle two bay, screwed for iron pipe of dia 15mm, fancy type fixed complete all as specified and as directed.

CP Angle valves cast copper alloy,fancy type,with iong shank and cup, bore 15mm, fixed complete all as specified and as directed.

125 mm dia brass chromium plated shower rose with swivel joints complete all as specified and as directed.

600mm long Tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wooden beded in cement mortor 1:3 with MS screws complete all as specified and as directed.

1000 ltrs capacity Rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part-I and as directed including suitable nipple HDPE water tank

20mm dia Gunmetal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

20 mm Ball Valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed for iron pipes complete all as specified and as directed.

Roughing surfaces of old concrete by picking up , sweeping,cleaning and washing down with water to remove dust etc including taking down Tar felt and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound with 3 mm thick plain polymeric water proofing membrane, of weight not less than 3.5 Kg per Sqm and bonded completely to the surfaces with overlap of 10 cm (overlap to be thermo fused by flame) to be laid by companycomplete all as specified and as directed. (WPC shall be measured and paid separatley). (Note : No extra cost shall be paid to contractor in r/o any removal of existing roof treatment.)

Supply only (LW+)water proofing liquid solution complete all as specified and as directed.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete (1:4:8) type D2 for 150mm dia pipe complete all as specified and as directed.

SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:4) as in manholes, septic tank, filter bed, walls, drains etc complete all as specified and as directed.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4). (Note:- reinforcement will be measured and paid seperately.)

Soakage well of size 3 m (dia) x 3 m (depth) including necessary excavation and earthwork, in any type of soil, PCC foundation brick work in CM 1:6 (walls shall be honey combed as shown on drawing), RCC cover slab in M-25, filling the well with brick bats complete all as specified and directed and as shown on drg No CETD-1202/2003 dated 09 Oct 2003 (Revised upto 14-10-14) (sheet1/2&2/2). Note: 1.The drawing has not been made part of the tender document and it is assumed that the tenderers are in possession of the said drawing before quoting their bids being typical detail drawing. However the bidders are free to visit any MES office for refering the same during office hours. 2. RCC shall be M-25 grade design mix irrespective of whatever mentioned in drawing. 3. Foundation PCC shall be 1:3:6 type C-2 irrespective of whatever mentioned in drawing.

Provision of septic tanks (for 100 users), including necessary excavation and earthwork, in any type of soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole cover having 6 mm plate embedded all around/fibre reinforced cover with angle iron frame, vent shaft and sludge chambers etc. complete all as specified and directed and as shown on drg No CETD-1202/2003 dated 09 Oct 2003 (Revised upto 14-10-14) (sheet 1/2 & 2/2). Note :1. The drawing has not been made part of the tender document and it is assumed that the tenderers are in possession of the said drawing before quoting their bids being typical detail drawing. However the bidders are free to visit any MES office for refering the same during office hours. 2. Depth of inlet pipe from ground level shall be 70 cm. 3. RCC shall be M-25 grade design mix irrespective of whatever mentioned in drawing.

Surface dressing hard / dense soil not exc 15cm deep and removal of surplus materials out side MOD land complete all as specified and as directed.

Hard core broken stone or boulders of gauge exc 63mm but n exc. 100mm, deposited spread and levelled in layers n exc. 15cm thick watered and rolled/ramed to a true surface complete all as specified and as directed.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to floor complete all as specified and as directed.

15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM 1:4 complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment. complete all as specified and directed.

Supply and fixing Kerb stone of size 300mmx300mmx100mm thick made of precast cement concrete 1:2:4 type B-0 using 12.5mm grated crushed stone aggregates including earth work for laying kerb stone, complete complete all as specified and as directed. Make : Ruchi or equivalent in performance of makes as specified in PS.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar complete all as specified and directed.

Dismantling iron work of any description complete all as specified and directed.

Dismantling old serviceable/unserviceable barbed wire including removing of unserviceable barbed wire from site and serviceable materials kept in safe custody for re-use complete all as specified and directed.

Excavation over areas not exceeding 1.5 m deep and getting out as in soft/loose soil complete all as specified and directed.

Removing excavated material exc 250m but n.exc 500 m and deposited where directed complete all as specified and directed.

Use & waste of form work to sides of footings, rough finished flat surfaces complete all as specified and as directed.

Use & waste of form work to sides of retaining wall etc rough finished surfaces complete all as specified and directed.

Use & waste of form work to sides of columns etc rough finished surfaces complete all as specified and directed.

RCC M 25 design mix (RMC), using 20 mm graded stone aggregate as in footing complete all as specified and directed.

M & L for broken glass coping on top of walls, embedded in cement mortar 1:3 complete all as specified and directed.

RCC M 25 design mix (RMC), using 20 mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia as in reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed not less than 0.9mm dia) complete all as specified and directed.

Boulder pitching grouted with cement and sand mortar 1:6 hand packed tightly complete all as specified and directed

Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to E-250 complete all as specified and directed.

Mild steel work conforming to grade Fe-165 (Fe-290) angle post or struts in fencing fixed independently including cutting and bending to shape as directed drilling holes, notching for wire etc. complete all as specified and directed.

Applying two coats of cement based paint on wall over a coat of chalk whiting including preparation of new plastered surfaces complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and directed.

S & F Punched tape concertina coil (including spike and handle) with 50 turns and 1050mm dia, width of barbed 9mm and spacing of clips 23.5mm to 24.5mm c/c weight of coil will be 10 to 14 kg without packing. Coil length will be 6m when opened up etc complete all as specified and directed

S & F galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of post including securing and tying at crossing with and provision of galvanised mild steel wire staple or steel pins etc complete all as specified and directed. (Each line wire to be mesured)

Hand packing broken stone or boulders (any thickness) at back of walls over arches etc and raising (or lowering) to the required level complete all as specified and directed.

110 mm dia PVC (SWR) pipes single socketed in any length as in weepholes of retaining wall complete all as specified and directed.

Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar in any description complete all as specified and directed.

Complete removal of existing treatment applying two coat of cement base paint in old surfaces on walls complete all as specified and directed.

Walling of random rubble stone masonry uncoursed, with best quality locally available harder stones such as granite, trap, basalt, trap, basalt stone etc, well bonded, bedded and solidly hearted , built in cement mortar 1:6 complete all as specified and as directed.

Boulder filling dry, hand packed tightly, as in wire crate apron bunds, complete all as specified and directed. (Wire crate shall be measured seperately)

Wire net trungers with galvanised mild steel wire with 3.14 mm dia of wire (cold dip) wooven in square size mesh , size of mesh 75mmx75mm complete all as specified and directed. (Note : Cost of labour for boulder filling shall be deemed to be included in cost of fixing of trungers)

Point wiring for one light point /fan point/ bell point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable 1100V grade in and including not less than 2.00 mm thick and 20 mm dia Non metallic Rigid PVC surface/Concealed Conduit ( ISI marked ) with and all accessories 1.5 mm thick mild steel terminal boxes concealed on walls, painting the same inside and out side with one coat of black bitumen paint with 3mm thick hylam brand bakelite sheet cover for fixing of piano switches/sockets/ regulator etc along with PVC insulated and unsheathed FRLS 1.5sqmm multi stranded copper conductor cable (green color) as earth lead, & connected to common earth and earthdolly, making good the disturbed surface to match with the existing specification complete all as specified and as directed.

All as per description of Ser Item No.111 here-in-before but for one 3 pin 5 Amp socket outlet point controlled by one push button on independent board complete all as specified and directed.

Switch piano flush button single pole one way 5 amps 240 volt complete all as specified and directed.

Switch socket combination 15 Amps 2-in-1, 5 Pin flush type, 230 volts complete all as specified and directed.

Ceiling rose surface bakelite 3 terminals complete all as specified and directed.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers along with all electrical wire connection complete all as specified and direceted.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good to distributed wall surfaces to match with existing complete all as specified and directed.(Note-MCBs will be measured separately)

MCB single pole 240 volt any rating from 10 to 40 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed.

MCB TPN 415 volt any rating from 40 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 4 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 2.5Sq mm as earth lead complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.30 mm thick burried directly in ground (earth pit not less than 2.25 Mtrs below normal ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead 4 mm dia by means of bolts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and indicated and testing on completion including excavation earth work drilling holes for electrode PCC pit & cover, funnel, water pipe lugs GI pipe medium grade protection pipe for earth lead up to DBs complete all as specified and directed.

Angular Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for light fittings complete all as specified and directed.

Supply and fixing LED lights fitting 1x 22W, 230V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed..

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Street light Bracket complete made of GI pipe of suitable size, medium grade 1.2 m long bent to shape as per site requirement along with MS flat iron clamps with nuts, bolts, washers including grouting the same with wall complete all as specified and directed.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 16 Sqmm x 4 core size all as specified including taking down old cable complete all as specified and directed. Note : Earth work and other connected work shall be measured & paid sperately.

Excavation in trenches and exceeding 1.5m wide and not exc 1.5m in depth in hard/dense soil and getting out complete all as specified and directed.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cable to give mechanical protection to underground cables complete all as specified and directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and directed.

s l sharma and sons

vijay constrction co

SINGH CONST CO

M/S ASHOK KUMAR PACHIALA

BHAGWATI TRADERS